Airport Utility can't find Airport Express after setting up as repeater station

I wanted to extend my 2Wire-based wireless network into a specific room that never seems to be able to pick up the signal, and found the following instructions on how to do so on Apple's website:
(note: these instructions were submitted by another user in response to a question as to whether or not an Airport Express could be used as a repeater station for non-Airport Extreme-based wireless networks - linked here http://store.apple.com/us/question/answers/product/MB321LL/A?pqid=QY4CAJJC7KFTTD KYH72DKPXF4CAUA9D4J).
Yes, you can do this two ways: If you can connect your airport express to your router via ethernet, then you will perform the following steps in the airport utility:
1. Select your airport express.
2. Select manual set up.
3. Under Wireless, select Participate in a WDS network
4. Enter your network name, radio mode, channel, and security
5. Under WDS, select WDS main
6. Check wireless clients
7. Add the MAC address of the router
8. Click update
That's it
Now, if you connect your airport express to your router wirelessly, all the steps are the same except for step 5. In this step, select WDS remote instead. Everything else is the same.
I followed those instructions exactly with my Airport Express and, after restarting, the amber light is flashing on and off continuously and the Airport Utility can't find the Airport Extreme base station. What the heck went wrong here?

Update:
I restarted the laptop I used to set up the AX as well as pushing the "reset" button on the AX (first time - pressed it for 1 second, Second Time - pressed and held for 15 seconds then let go). The Utility still isn't recognizing the base station.
I also upgraded the Utility's software to 5.5.3 right before I went through these steps, and now it's not recognizing the base station. ARGH.
Update #2: I plugged the AX into my laptop with an ethernet cable and the utility STILL can't detect it. This is ridiculous.
Update #3: Not 30 seconds after update #2, it FOUND the **** AX >.< I'm updating the firmware, but I still can't get it to work as a repeater station if I have to plug it into my laptop all the time JUST to get the Utility to recognize that yes, Virginia, there IS an Airport Extreme.
Message was edited by: bleedingrose19

Similar Messages

Airport utility can't find Airport Express

I reset my network today after getting a new Aiport Extreme AC. After setting up the Extreme, I wanted to add my Express stations (1 and 2 gen) back into the network. But neither of them are appearing in AirPort Utility under 'other wi-fi devices'. This picture shows the 1gen express several minutes after a hard reset. Same story with the 2nd gen express. Neither appear. I'm on a 2011 iMac, OS 10.9.5, Airport utility 6.3.2. Any help is appreciated. Thanks.

Hold in the reset button for 8-10 seconds on the 2nd Gen AirPort Express, then release and allow a full minute for the Express to restart.
During that time, restart your Mac.
Click the WiFi icon at the top of the screen, then look for a listing of New AirPort Base Station.
Click on AirPort Express just below that listing
Mavericks (and Yosemite) are notorious for "lost" AirPorts so you may need to repeat the actions above a few times. If you are still having difficulty, we'll need to check some Network settings on your Mac in regards to IPv6.
On your Mac.....open System Preferences (gear icon on the dock)
Open Network
Click on WiFi on the left to highlight it
Click Advanced at the lower right
Click the TCP/IP tab
Check that the setting for Configure IPv6 is set to Link Local Only
Click OK
Click Apply
Then, perform the same steps as above except click on Ethernet to highlight it
Restart your Mac again and see if the AirPort Express appears when you click on the WiFi icon
If still no luck....and if you have an iPhone or iPad handy......
Tap Settings on the home screen
Tap WiFi
Look for a listing of Set Up a New Base Station
Tap on AirPort Express

Airport utility can not find airport extream base station

I bought apple airport extream base station recently. I download ariport utility ion my iphone. But the airport utility cant find my airport extream base station.

Power up the AirPort Extreme for a few minutes
Hold in the reset button on the back of the AirPort Extreme for 10 seconds then release
Allow a full minute for the AirPort Extreme to restart again
On the iPhone home screen, tap Settings
Tap WiFi
Look for the listing of Setup A New Base Station
Tap on AirPort Extreme
The example below shows an AirPort Express. You will see AirPort Extreme
When you tap on AirPort Extreme, that will get the setup wizard running. Follow the prompts.

Airport utility can not find my airport express...

Airport utility can not find my airport express...
I was trying to connect a PC (Windows XP) laptop to my wireless network via the airport express.
I have a Mac with an airport that I use to get internet in my other room. I am trying to get internet on the laptop too.
I somehow manage to erase my network & now my airport utilities won't even scan/recognize my airport??
ANY help would be appreciated, mac helpline wanted $59 to help & I live in a small northern community where they do not have anyone that will address a Mac issue!!
Thanks for your time.

Thank you SO MUCH Tesserax for taking the time to help!
I powered everything down, slowly powered everything else up from the modem to the airport then the computer. I then reset the airport & rescaned it through utilities. I set up a new network & voila! wireless up & running again.
I am going to try to connect the laptop to the network now.....well, mabey tomorrow night, I've had enough for 1 evening!
I will update....or possibly be begging for more help...we'll see!
Thanks again for your time!

My airport utility can't find the airport device.

Everything is connected. I bought the device about eight months ago and have used it successfully to set up wireless networks twice. Now i have a DSL modem, and there was an error that the IP was in use. So i followed some tips online to reset both devices, restart, etc. Currently i have everything connected and plugged in, including with an extra ethernet cable from my laptop to the airport's wan port. However, NOW the airport utility can't find the device and it's just sitting there blinking amber slowly. The modem is all lit up and green and appears to be working. ***? is the airport express broken?

adubatowka14 wrote:
I got the AU to find my AE by connecting them with an ethernet cable.
How are you configuring up the Express once you have AU working with it? Please provide us with what you want/need to have.

Airport utility can't find my airport base station

Im trying to set up a wireless internet at home. I have a comcast cable internet connected to motorola sb120 cable modem and I connected an ethernet cable from the modem to my aiport base station. when I open the airport utility in my macbook (also from my iphone 4s) the airport utility can't find the base station. the base station has a solid green ligh on and the modem "llink" light is binking amber. If I connect the ethernet cable frm the modem to my macbook I can get the internet with out any problem ...please help me set up my wireless internet with airport base station. ty.

Suggest that you try the following:
1) Reset the cable modem. There is a reset button on the back or bottom of the device. Check your documentation for the modem for exact details. In general, you press the reset button for a few seconds and then power down the modem completely.
That means pulling the power plug from the back of the modem or the AC wall plug
Leave the modem powered off at least 30 minutes
2) Perform a Factory Default Reset on the AirPort Extreme using the instructions in this document
Resetting an AirPort Base Station or Time Capsule FAQ
3) Then power off the AirPort Extreme
After 30 minutes.....
4) Connect the Ethernet cable from the cable modem to the WAN port (circle icon) on the AirPort Extreme
5) Temporarily, connect another spare Ethernet cable from your Mac to one of the LAN <-> ports on the AirPort Extreme
7) Power up the modem and let it run for 5 minutes by itself
8) Power up the AirPort Extreme the same way
At this point, the AirPort Extreme should be slowly blinking amber
9) Open AirPort Utility (I assume that you have AirPort Utility 6.0) and click on Other Base Stations, then click on the Base Station xxxxxxx representing your AirPort Extreme to start the setup process
AirPort Utility should suggest that you configure the AirPort Extreme to "Create a wireless network". Accept that option and enter the required wireless network name that you want and passwords
Follow any more prompts as required and AirPort Utility should configure the device for you
Wait 25-30 seconds for a green light
10) Disconnect the temporary Ethernet cable from your Mac to the AirPort Extreme
11) Log on to the wireless network that you named during the setup process
12) Report on your results

Airport Utility can't find base station

I feel like I must be missing something very obvious. But my Airport Utility can't find any base stations, even though I am successfully connected to this network, the base station is about three feet away from the computer, and Internet Connect has no trouble finding it and specifiying the base station's id.
I have just done a wipe-and-install of my whole computer; I've reinstalled all software from CDs or installers, and this utility wanted to upgrade to version 5.2.1 (it says Disk Version 2.0 on the disk) before running, so I did that. And no base station detected, despite rebooting the computer, and rescanning any number of times. I'm using OS 10.4.6.
What can I do?
Message was edited by: Paul-ny

There is something puzzling that bothers me, even though I have things working again.
I first lost access to the AEBS when I tried to use Airport Utility to change the security setting of my network. It has been on the default WPA2 setting, and I was wanting to downgrade that to WEP because the long WPA password was too long to be accepted by my Palm TX Wifi software. But the shorter WEP password shouldn't have been a problem. At the time, after my system reinstall, the utility and the base station seemed to be working all right.
When I completed resetting the base station with WEP, though, there was an error message, after which I could no longer connect to the network with my laptop (using the old password or the new password), and then the utility lost sight of the base station as well. I had to do a hard reset and start over. When I did the same thing again, the same thing happened. When I reconfigured the base station with the WPA2 security, though, it all worked, and my laptop could get back online.
At this point I tried changing it again to WEP, and the same problem recurred. One last time with WPA2, and that's where I am now, except that I was pleased to find that my PDA, which had just been replaced under warranty, has some newer software in it and it now can accept my passkey (?)-- my airport code rather than the 64(?)-digit number version of it, so it's working, too.
But apparently Airport Utility has lost sight of the base station again. I don't need it for anything, but this is annoying. What's more curious, though, is what was happening when I chose WEP security.

Airport utility can not find extreme station after upgrade to 7.5.2

i been using extreme for about 3 years and it was fine until yesterday i upgrade to 7.5.2, it result i lost the internet. opened airport utility from my macbook, said" it can not find any wireless device" but on the top right of mac windows, the signal sign is still there,
i suspect it is something wrong with the IP setting, but i has't changed any thing myself, maybe the new updates change it?

kfc360 wrote:
"it can not find any wireless device"
Welcome to Apple's discussion groups.
Your system details don't mention what type of Mac you have, but if you can move it near to the AirPort Extreme and connect an Ethernet cable to a LAN port on the Extreme, then AirPort Utility should be able to see it. Once AirPort Utility can see it you can begin to investigate the problem in more detail.

Airport Utility doens't see aiport express after reconfiguring

I have my airport express connected through bridge mode to a 2Wire 2701 HG-B modem. I just bought this Airport Express and whenever I try to modify settings, Airport Utility can't see it after the restart, even though I'm still connected through wifi to the same airport express. This is frustrating since I'm trying to experiment with the settings and would prefer to connect through 5GHz on 802.11n. But I need to reset the Airport Express to factory settings each time to in order to access the settings through the Utility again to retry everything. I'm on a Mac Pro with wireless N airport card. Is my Airport Express defective? This can't be right.

+"I do have another question now that I can play around with the settings. I'm having trouble setting it up so I can receive the 5GHz signal on 802.11n"+
I believe the the default settings for the Extreme are 802.11n 5 GHz on the main network and 802.11n (b/g compatible) on the guest network.
So that I'm clear, are you saying that you are having difficulty connecting to the the main network? Your Mac should be capable of handling "n" settings. Another issue may be the fact that the 5 GHz signals are absorbed by walls and any other obstructions much more quickly than the 2.4 GHz signals. Unless you have close to line-of-sight with the router, many users find that they get a better connection at 2.4 GHz than at 5 GHz.

My airport utility can't find my airport base station

My AirPort Express stopped working! It keeps flashing the amber status light. I tried finding the problem with airport utility but airport utility can no longer find my airport base station. I did a hard reset but I am not sure what to do now.????

Suggest that you try the following:
1) Reset the cable modem. There is a reset button on the back or bottom of the device. Check your documentation for the modem for exact details. In general, you press the reset button for a few seconds and then power down the modem completely.
That means pulling the power plug from the back of the modem or the AC wall plug
Leave the modem powered off at least 30 minutes
2) Perform a Factory Default Reset on the AirPort Extreme using the instructions in this document
Resetting an AirPort Base Station or Time Capsule FAQ
3) Then power off the AirPort Extreme
After 30 minutes.....
4) Connect the Ethernet cable from the cable modem to the WAN port (circle icon) on the AirPort Extreme
5) Temporarily, connect another spare Ethernet cable from your Mac to one of the LAN <-> ports on the AirPort Extreme
7) Power up the modem and let it run for 5 minutes by itself
8) Power up the AirPort Extreme the same way
At this point, the AirPort Extreme should be slowly blinking amber
9) Open AirPort Utility (I assume that you have AirPort Utility 6.0) and click on Other Base Stations, then click on the Base Station xxxxxxx representing your AirPort Extreme to start the setup process
AirPort Utility should suggest that you configure the AirPort Extreme to "Create a wireless network". Accept that option and enter the required wireless network name that you want and passwords
Follow any more prompts as required and AirPort Utility should configure the device for you
Wait 25-30 seconds for a green light
10) Disconnect the temporary Ethernet cable from your Mac to the AirPort Extreme
11) Log on to the wireless network that you named during the setup process
12) Report on your results

Airport Utility can not find air port extreme base station

I am running XP home on my computer and have an air port extreme base station connected to it wired. I have no problem connecting to the internet yet more times then not the air port utility can not find the base station. On occasion it will find it but most of the time it can not. Rebooting does not help.

I recently purchased one of the new Airport Extreme base stations and after carefully reading the instructions; I first installed the Airport Utility 5.5 that came on the CD onto my MacbookPro. I then connected the new base station to my macbookpro via Ethernet and power it up. I copied a previously saved configuration onto it. All my printers, IMAC and macbookpro were able to connect.
I then used my older base station and my airport express to extend the N and G networks through the house. My problem was (1) the new Airport utility would consistently lose the older extreme base station and the airport express, (2) An my HP printers keep losing the wireless connection to the new airport extreme base station. The only resolve was to consistently restart the new base station, after which (1) the new airport utility would see the older base station and express again and (2) the wireless connection to the printers would be restored.
After about a week of this, I removed the new Airport Extreme and replaced it with the older extreme (802.11N DRAFT) and de-installed the Airport Utility 5.5 and re-installed Airport Utility 5.4.2 and everything works fine.
Has anyone else experienced any problems with the newly released Airport Extreme (fully 802.11N) base stations and Airport Utility 5.5?

Airport Utility can´t find anything?

My Airport Express and Time Capsule shows on both my iPhone and my PC but not on my Mac? I can´t stream from the PC as well as gain access wirelessly (is that a word?) to the TC!
I couldn´t even set it up on my Mac (tried several times, came up with an error) but had to set it up on my PC. I believe it was after some update it went wrong! (It doesn´t show in the Finder either)
Yes, - I have restarted my Mac, I rebooted both modem and router, - that´s not the problem (remember It shows on the 2 PC´s)
I had the latest 6.1 (610.31) and tried to run the 5.6.1 verson instead with no luck!
Please help!

If you are using a PC, the Windows firewall, anti-virus, or Microsoft Security Essentials (if you have it installed) is likely blocking the connection from your PC to the AirPort Extreme.
You will have to get into the settings for each of these applications to check on blocked connections and then "allow" an "exception" so that the connection will occur.
You might have better luck if you connect your PC directly to a LAN <-> port on the AirPort Extreme using an Ethernet cable.
Once you get the connection working on AirPort Utility, click on the AirPort Extreme then click Manual Setup.
Click the Wireless tab located below the row of icons to reveal the wireless settings. Change the password and verify here, then click Update to save the new settings.

Airport Utility can't see Airport Express Device

I tried to print some documents and I received a message telling me the printer is not ready or may not exists, so I launch the Airport Utility to see what is going on and there is no Airport Express just my Time Capsule.
I already reset the airport express to factory settings and everything goes ok until the green light shows but the airport utility can't see it.
Any help will be appreciate
thanks
Dan
I already tried connecting the Airport Express to my computer with an ethernet cable

Connect an Ethernet cable between the wall jack and the WAN (circle of dots) port on the AirPort Express. Connect a second cable between the LAN (opposing arrows) port on the Express to your computer.
You should now be able to access the Express using the AirPort Utility to configure the Express as a WAP.

AirPort Utility can't find Netgear router OR new AirPort Express

Hello,
I couldn't find my situation fully addressed in older posts, so I'm posting one myself.
I am trying to EXTEND my current network with a newly purchased AirPort Express. My equipment is as follows:
Comcast modem connected via ethernet cable to...
Netgear Nighthawk AC1900 R7000 dual-band router
One three-year-old Mac Mini running Lion
One newer MacBook Pro running Mavericks
Two iPhone 4S, latest software updated as of Nov. 2014
Two-year-old iPad, latest software updated as of Nov. 2014
Newly purchased AirPort Express as of Nov. 2014
We have a large house with an office at the extreme end resulting in a week signal, so I need to extend my network. The Netgear router sends a strong signal otherwise, and ALL devices are working properly and are fully connected to the WIFI network.
So here is the problem:
I've tried many, many times to connect the APE using AP Utility with only two successful connections, but these connections were to "Join Existing Network" not to extend that network, but I selected this option as it seemed closest to what I want to do since "extension" of network was not an option. Then I see that I can edit the APE within AP Utility. I've done so, resetting the unit as a network extender, and the two times I tried this I sat waiting for five minutes for the thing to update only to get an error message. At this junction I could do nothing but remove the APE in AP Utility by "forgetting" it. No other options were available that I could see.
Now, the two times I've done the above, were two times within 20+ attempts to get AirPort Utility to even see the darn thing. I've tried placing the APE near the Netgear router, moderately close (other side of room) and even at the far end of the house, and neither the APE or the Netgear router were ever found in the AP Utility save the two incidences mentioned above. I've scoured the net, rechecked all connections and performed all troubleshooting procedures I can find to no avail. All I get is a flashing amber light and no connection
A: Why won't AirPort Utility find my Netgear Router?
B: Why won't AirPort utility find my AirPort Express?
C: Why, on the two occasions the AP Utility did find the APE, did it not give me the option anywhere to set it up as an EXTENDER to the current network?
D: Is there any other way to add the APE to my network as desired without using AP Utility? (I do have the Negear Genie app, but I don't see options for adding a device for network extension so far)
I'm at wits end. Can anyone help?
Oh, and I've tried using AP Utility on both Macs listed above with the same results.
Thanks for your help!

A: Why won't AirPort Utility find my Netgear Router?
AirPort Utility works only with an Apple router, as does the utility for a Netgear work only with a Netgear router.
B: Why won't AirPort utility find my AirPort Express?
Any of 3-4 common reasons. We'll have to work on troubleshooting that.
C: Why, on the two occasions the AP Utility did find the APE, did it not give me the option anywhere to set it up as an EXTENDER to the current network?
Apple designed the wireless "extend" feature on their routers to only work with other Apple routers.
D: Is there any other way to add the APE to my network as desired without using AP Utility?
No
Not sure how you want to proceed at this point. It might be possible to use the AirPort Express to extend the Netgear network if you connect it using a permanent, wired Ethernet cable connection back to the Netgear router.
If you cannot run the Ethernet cable, your best bet by far is to use another Netgear extender or repeater, which would likely be compatible with your Netgear router.

Airport Utility can't find base stations.

I have three base stations in my network, an old extreme, the new extreme, and an express. On my 17" macbook pro, the airport utility cannot detect any base stations. It can connect to my network, and surf the internet fine. It just can't find the base stations. On my roommates macbook, airport detects them fine. We are both running fully updated versions of Leopard. I have already done a clean install to see if it fixed the issue, but it still persists. The only reason this is annoying is I have lost my ability to stream music to the express station. Has anyone even encountered this issue?

I've had the same problem with my leopard machine.
I have an AirPort Extreme base station connected to the internet and an AirPort Express connected to my stereo set. iTunes couldn't find the express anymore, so I tried to use the Airport configuration program. That couldn't find any base stations (neither extreme nor express) although my internet connection was working (via the extreme base station).
Connecting using an IP address (AirPort config programm, shift-cmd-O) did work, so if you only need to reconfigure the base station you can do that without having Airport Config find the base station.
After restarting the base station my Mac found both the base stations. Go figure.
The trouble isn't caused by sleeping as my Leopard Mac isn't allowed to sleep due to crappy connections afterwards.

Airport Utility can't find Airport Express after setting up as repeater station

Similar Messages

Maybe you are looking for