Airport Utility can't "see" base stations after Leopard 10.5.4

After upgrading to Leopard 10.5.4, Airport Utility can't "see" Airport Extreme UFO version and Airport Expresses. But the Expresses are glowing green, so I assume they're working. But if they can't be "seen" when scanned by Airport Utility, they can't be added as speaker options to iTunes.
Have unplugged and re-plugged in power to Airport Extreme and Expresses.
Oddly enough, at one point the sound through my eXpresses would kick in for five seconds and then disconnect for a minute, then play for five, then disconnect for a minute.
This same thing happened when I switched to Leopard.
Any solutions?

Well what do you know...after a week, it just magically decides to work, without even using Airport Utility.
Boy are these Airports touchy....and unreliable.
I still want to know: What makes these things drop in and out???

Similar Messages

  • Airport Utility Can't See Base Stations

    I am sure this is something simple. I can log onto an Airport Network with my Powerbook just fine but no matter what I do, I cannot "see" any of the base stations on the network. I receive the error message "Airport Utility was unable to find any Apple wireless devices." This happens on at home, at my office, and at my friends' house. Other computers log on without any difficulty.
    Both of my computers are using 10.5.2 and have been since February. Airport Utility is v. 5.3.1. Everything was working fine until one morning when I woke up and found that iTunes couldn't find my remote speakers. I had made no changes or updates in the few days before. It just stopped working.
    Anyone else had this problem or know what might be the cause?
    Thanks

    Thanks for the reply. I have tried power cycling everything. I also powered things up in different in different order to see if that would solve the problem. It didn't. It just makes no sense that I can be on the network and not see the base station.
    Thanks again for your help.
    Alan

  • Airport Utility can't find base stations.

    I have three base stations in my network, an old extreme, the new extreme, and an express. On my 17" macbook pro, the airport utility cannot detect any base stations. It can connect to my network, and surf the internet fine. It just can't find the base stations. On my roommates macbook, airport detects them fine. We are both running fully updated versions of Leopard. I have already done a clean install to see if it fixed the issue, but it still persists. The only reason this is annoying is I have lost my ability to stream music to the express station. Has anyone even encountered this issue?

    I've had the same problem with my leopard machine.
    I have an AirPort Extreme base station connected to the internet and an AirPort Express connected to my stereo set. iTunes couldn't find the express anymore, so I tried to use the Airport configuration program. That couldn't find any base stations (neither extreme nor express) although my internet connection was working (via the extreme base station).
    Connecting using an IP address (AirPort config programm, shift-cmd-O) did work, so if you only need to reconfigure the base station you can do that without having Airport Config find the base station.
    After restarting the base station my Mac found both the base stations. Go figure.
    The trouble isn't caused by sleeping as my Leopard Mac isn't allowed to sleep due to crappy connections afterwards.

  • Wireless working, but Airport Utility can't find base station

    I am having issues with Apple TV and iTunes that led to me investigating my new Airport Extreme base station (AEBS) as possible cause.
    Oddly, I'm right next to the AEBS now and the wireless is working sweetly as I type. However, when I use the Airport Utility to access the base station, it can't find it - I can 'rescan' for all the hours but with no luck.
    Any ideas what's going on here?

    I've just encountered this problem for the first time. On my brand new MacBook Air (Leopard factory installed), I opened Airport Utility, entered Manual Setup, and restarted my Airport Extreme from the Base Station menu. It restarted, but once it was back up the Airport Utility could no longer find it, even though I was connected to the internet (and the Network preferences pane showed connection and a green light).
    I have a MacBook (vintage 2007) that's still on Tiger -- I've never had any problem using Airport Utility from there, so I imagine I can still configure the base station from there. But I hope this issue is on Apple's radar so there'll be a Airport Utility update that fixes it.

  • AEBS stopped working/ airport utility can't read base station configuration

    AEBS was working fine including the 7.1 update except printer wasn't working. As I attempted to trouble shoot network, AEBS stopped working. I tried accessing it through airport utility but it couldn't find the base station. I have now done a hard reset four times and though airport utility will recognize the base station it gets hung up trying to read the base station configuration. So I can't troubleshoot the AEBS from airport utiltity and the yellow light keeps flashing. What do I do now?

    AEBS was working fine including the 7.1 update except
    printer wasn't working. As I attempted to trouble
    shoot network, AEBS stopped working. I tried
    accessing it through airport utility but it couldn't
    find the base station. I have now done a hard reset
    four times and though airport utility will recognize
    the base station it gets hung up trying to read the
    base station configuration. So I can't troubleshoot
    the AEBS from airport utiltity and the yellow light
    keeps flashing. What do I do now?
    I had the same problem and a hard reset (6 seconds on the reset button) was recommended by Apple Tech support and that did it for me. The AE was back being seen and allowing me to reconfigure it from scratch.

  • Airport Utility can't find base station

    I feel like I must be missing something very obvious. But my Airport Utility can't find any base stations, even though I am successfully connected to this network, the base station is about three feet away from the computer, and Internet Connect has no trouble finding it and specifiying the base station's id.
    I have just done a wipe-and-install of my whole computer; I've reinstalled all software from CDs or installers, and this utility wanted to upgrade to version 5.2.1 (it says Disk Version 2.0 on the disk) before running, so I did that. And no base station detected, despite rebooting the computer, and rescanning any number of times. I'm using OS 10.4.6.
    What can I do?
    Message was edited by: Paul-ny

    There is something puzzling that bothers me, even though I have things working again.
    I first lost access to the AEBS when I tried to use Airport Utility to change the security setting of my network. It has been on the default WPA2 setting, and I was wanting to downgrade that to WEP because the long WPA password was too long to be accepted by my Palm TX Wifi software. But the shorter WEP password shouldn't have been a problem. At the time, after my system reinstall, the utility and the base station seemed to be working all right.
    When I completed resetting the base station with WEP, though, there was an error message, after which I could no longer connect to the network with my laptop (using the old password or the new password), and then the utility lost sight of the base station as well. I had to do a hard reset and start over. When I did the same thing again, the same thing happened. When I reconfigured the base station with the WPA2 security, though, it all worked, and my laptop could get back online.
    At this point I tried changing it again to WEP, and the same problem recurred. One last time with WPA2, and that's where I am now, except that I was pleased to find that my PDA, which had just been replaced under warranty, has some newer software in it and it now can accept my passkey (?)-- my airport code rather than the 64(?)-digit number version of it, so it's working, too.
    But apparently Airport Utility has lost sight of the base station again. I don't need it for anything, but this is annoying. What's more curious, though, is what was happening when I chose WEP security.

  • Airport Utility can't find base station, but station works fine

    I recently purchased an AEBS. The network seems to be working fine (I have an iMac flat panel (10.3) connected via Ethernet, an iBook (10.3) connecting wirelessly, and a Mac mini with 10.4 connected wirelessly). However, airport utility doesn't see the base station. Should I be concerned?

    Got my answer from previous posts -- had to do a hard reset *while the device was plugged in and wait for the flashing green light* then it all worked fine. thanks !

  • Airport utility can not find extreme station after upgrade to 7.5.2

    i been using extreme for about 3 years and it was fine until yesterday i upgrade to 7.5.2, it result i lost the internet. opened airport utility from my macbook, said" it can not find any wireless device" but on the top right of mac windows, the signal sign is still there,
    i suspect it is something wrong with the IP setting, but i has't changed any thing myself, maybe the new updates change it?

    kfc360 wrote:
    "it can not find any wireless device"
    Welcome to Apple's discussion groups.
    Your system details don't mention what type of Mac you have, but if you can move it near to the AirPort Extreme and connect an Ethernet cable to a LAN port on the Extreme, then AirPort Utility should be able to see it. Once AirPort Utility can see it you can begin to investigate the problem in more detail.

  • Airport Express Can't See Base Station

    I have an airport extreme base station that has two computers normally connected to my network wirelessly (iMac G4 and Powerbook G4) which have worked fine for months. After completing an apple security update this evening on both computers the Powerbook G4 did not automatically connect to the network upon restart as it normally does. The iMac G4 started up fine and is how I am posting this note. The powerbook on the toolbar shows the network I want to join but when I select it (and and see the check mark next to it) I still cannot access the internet. When I run the Airport admin utility it cannot see any base stations (despite the iMac sitting 1 foot away and working perfectly). When I manually give it the IP address and password it says "unable to read the configuation of the selected base station." When I try the Airport Setup Assistant it also lists my network as one that I can choose but when I click on the "continue" button it says "unable to establish a network connection" and that my computer could not connect to the internet. Help!!! I have tried every angle I can thing of to get the Powerbook to connect like it did a few hours ago.

    I have just discovered the same problem. After downloading the latest security update my Powerbook G4 [10.3.9] can not "see" any base station or express and/or connect to my network. The G5 running 10.4.5 works fine and sees all. Everything had been working just fine before the update then... Have tried all the work arounds I can think of and wasted a great deal of time. Any answers out there?
    G5Tower / G4Powerbook   Mac OS X (10.4.5)   G4Powerbook OS 10.3.9

  • Airport Utility does not see base station

    Hello,
    I just got an Airport Extreme. I am able to connect to it from mac and pc running vista but I am not able to see the base station from the airport utility on the windows platform. I can see it from the mac. Any ideas why - am I missing something on the windows platform.
    Thanks
    Praveen

    Thanks for your answers. I found this answer in a different thread. Once I unchecked CheckPoint VPN software - the base stations now show up in Airport Utility.
    Re: iTunes 7 for Windows Vista: AirTunes won't connect to remote speakers
    Posted: Jun 25, 2007 6:06 AM in response to: Vanlew Reply Email
    I had same frustrating problem.
    I was able finally to restore AirTunes.
    In Local Area Connection Status.Properties
    In the "uses the following Items" list,
    Item "Check Point SecuRemote" appears.
    This is the VPN CLient that was installed to let me log in to my office network from home.
    Uncheck SecuRemote, OK; iTunes Speakers button shows.
    Check SecuRemote, OK; iTunes Speakers button disappears.
    This looks like a bug in Checkpoint Software.
    In your case, something else may be interferring.
    Other OS Vista 32 bit - SecuRemote beta for Vista

  • Solid Green light at start up. Airport utility can't find base station.

    Help!
    I've got a problem with my Airport Extreme base station. It's not so extreme. When I hook it up, I get a solid green light and it can not be found by the airport utility in order to set up. I've tried resetting it, power on and off. Nothing. Any suggestions on how to start over or get this thing working?
    Thanks,

    David_957, Welcome to the discussion area!
    Try temporarily connecting your Mac to the AirPort Extreme base station (AEBS) via Ethernet. After you get it configured you can disconnect the Mac's Ethernet connection to the AEBS.

  • AirPort Utility can't detect base station but my laptop's wireless utility

    Just bought an AirPort Extreme base station yesterday. I have installed the new version of AirPort Utility from the disk on my Windows XP laptop and updated it online.
    Visibility of the station from AirPort utility is very sporadic. I have gone through setup twice and done a re-set of the station once. I can see the station from my laptop's wireless utility, but can't establish an internet connection. Can't connect with AirPort Utility long enough to figure out if the configuration is ok.
    Anyone seen anything like this? Could I have a bad base station? thanks.

    I have a similar problem, only it is my MacBook that can see the Airports, and my G5 that cannot. To make it even more counter-intuitive, the G5 is *plugged in* to the Airport Extreme base station, and while it gets internet and other network devices, it cannot talk to the very router it is connected to.

  • Wireless encryption when Admin Utility can't see base station

    I am running an iMac G5 circa 2006 and an iBook from 2001. I have an old-school Airport Extreme base station (the one that looks like a little spaceship). The base station is connected to a cable modem. The signal is great, I can get on the Internet no problem, but neither computer recognizes the base station in Airport Admin Utility. No base stations come up, so I can't configure the base station to encrypt my signal.
    I tried implementing a WEP through the Sharing tab, but that didn't work. My signal is still unsecured.
    Any suggestions?

    There are several 'old-school' AirPort Extreme Base Stations (AEBS) models. Graphite, Dual Ethernet (Snow), and the current AEBS.
    Sorry but that is not quite true.
    The graphite AirPort base station (ABS) and Dual Ethernet (aka snow) ABS are NOT AirPort Extreme base station (AEBS). They operate at 802.11b.
    But... before this week there were 3 different versions of the AEBS. You can see the differences between those in the table at www.ifelix.co.uk/tech/1301.html

  • Airport Utility does not see Base Station but I'm still online

    I have an original airport base station and just downloaded Airport Utility 5.5.1
    The base station is working because I'm online with it posting this thread.
    But Airport Utility 5.5.1 does NOT see it...
    The strange thing is that I have one of the early dome Airport Extremes here as well. That one IS recognized but the Airport Utility.
    Anyone have any suggestions as to why the original Airport is not showing up in the utility even when I know it's obviously being seen by my card and connecting to the web?
    Thanks
    g

    Did you power cycle your network as follows?
    Power everything on the network down, order is not important
    Wait a few minutes, then start the modem first and let it run a few moments by itself.
    Then start the next device connected to the modem and let it run a few moments.
    Then start each device the same way until everything is up on the network.

  • Can't see Base Station

    After a restart I lost my Airtunes and the Airport Extreme and Express were no longer findable in the Airport Admin. Utility.
    I am now connected by Ethernet cable to the Extreme ( usually I connect wirelessly), but still cannot 'see' the base stations.
    I can connect to the internet and see my networks: I can call up the base station under the 'other' tab, but without being able to 'see' the base stations, I can't use the Airport Setup assistant to reestablish a connection from my Express to my home network.
    I have followed the instructions at http://www.info.apple.com/kbnum/n106685 and at Point 15 cannot see the Base station whether I configure manually or using DHCP.
    I have hard reset both Express and Extreme Base Stations.
    I have tried disconnecting the router power for half an hour.
    My kids computer has its Airtunes unaffected by all these disruptions.
    Any ideas while the machine is on the kitchen table connected via ethernet
    Nathanael
    G5 iMac 20" 2 GB RAM   Mac OS X (10.4.4)   LaCie d2 External Harddrive
    G5 iMac 20" 2 GB RAM   Mac OS X (10.4.4)   LaCie d2 External Harddrive
    G5 iMac 20" 2 GB RAM   Mac OS X (10.4.7)   LaCie d2 External Harddrive

    This happens to me every morning after the Airport Extreme n has been inactive over the night. I swithch off Airport on my computer (I have the Airport indicator up in the menu bar), wait a couple of seconds and then switch it on again. Airport Utility than recognizes the base station.
    However, Airport Utility will not recognize an Airport Express which I have set up in "bridge mode", i.e. it is used only to connect to a printer. For the Airport Utility to find the Airport Express station, I need to do a change on the Airport Extreme n station and then "Update". As the Airport Extreme then restarts, Airport Utility will then also find the Airport Express and I will be able to print.
    This is cumbersome, of course, and useless for my kids who have no Admin authority and cannot make changes to the Airport Extreme (I have Access controls installed).
    This should get you going but is not the final solution.
    /Uno

Maybe you are looking for