Airport utility cannot find my new Time Capsule

I just bought a new timecapsule, connected it to my modem via the wan port, turned it on and the light went from green to flashing amber. Airport Utility does not find any wireless devices i can try over and over but no succes.
I reset the Timecapsule a few times already. Whatever i try airport utility does not find anyhting and i can make no connection with my timecapsule
I thought this should be so hard.. does anyone know whats going wrong?
I looked on various websites but i never get past the second 2 step: Airport utility recognizing my timecapsule
Also tried software update but it says everything is up to date..
Hope somebody can solve this!
Thanks in advance
Rhodo

Airport Utility does not find any wireless devices i can try over and over but no succes.
Look for another wireless network with a name like Apple Network xxxxxx and log on to this network. No password is required. Then open AirPort Utility.
Or, temporarily connect an Ethernet cable from your computer to one of the LAN <-> ports on the Time Capsule and then open AirPort Utility.

Similar Messages

  • Airport utility cannot find my new Airport extreme.

    I plugged in the airport, opened airport utility and it scans and says it finds nothing.  The airport is right next to my computer.  It is not out of range.  It is blinking orange. I have a dell inspiron 600m running windows XP.  My modem is a westell 6100g.  I anticipate problems getting them to work together, but i didn't expect to not be able to even find the airport to configure it.  What is going on here?  Please help.

    So I successfully set up the airport, disconnected it from the computer, connected it to the modem and used the laptop wirelessly, went downstairs to see if the other computer (a mac) could get online, it could.  Left the house, came back around midnight.  No wireless signal.  went to sleep.  this morning, no wireless signal. opened airport utility.  No airport found.  Reconnected laptop to LAN.  Found.  went through setup again.  got wireless signal.  disconnected laptop.  went in other room.  5 minutes later, no signal, no ability to see airport.  connected laptop to modem and put it in bridge mode.  same situation, only the signal seems to dissapear quicker.  I can access the internet by connecting my laptop to the airport LAN, and while that cable is connected I can see (and my computer says, use) the wireless network, but as soon as i disconnect the computer the wireless goes down.
    Bob- my windows firewall is completely disabled and i currently have no anti-virus software installed, so i don't think that is the problem.
    Any advice?

  • AirPort Utility cannot find TC

    I'm having problems with connecting my Time Capsule with my Mac via ethernet cable. AirPort Utility cannot find the device, the Capsule is flashing amber only. I have tried to restart the device and modem but still no progress.. Do you know what might be the problem? I'm confused..

    I am having the same problem. No matter how I attempt to connect TC (ie. Ethernet connected to Linksys Router or as the hub for my network connected directly to my cable modem) , it seems to start correctly (brief green light) then solid amber and I can hear the disk coming up to speed....and then Blinking Amber.
    The really odd part is that it worked perfectly for the first month.
    Obviously, Airport Utility can't find it!
    It is the 1 TB model.
    Please, any suggestions?

  • Airport utility cannot find new time capsule

    I have moved house and bought a new time capsule. The airport utility cannot find it. As context, I have successfully set up the new wi-fi network - should I use this to connect to the time capsule of my main wifi network ? I have also done a factory reset already. I think the cables are correctly plugged in - from the LAN output on my router to the WAN port on the TC - is this right ?

    As context, I have successfully set up the new wi-fi network - should I use this to connect to the time capsule of my main wifi network ?
    No, your cabled connection is far superior.
    I have moved house and bought a new time capsule. The airport utility cannot find it.
    Do you have iphone or ipad?? If so download the airport utility for iOS.. it is far superior to the Mac version.. and should be able to discover it.
    If you need to do it from the Mac.. start over.. sorry .. yet another factory reset is helpful.. do it properly like this.
    1. The Factory Reset universal
    Unplug your TC/AE. Hold in reset. and power the TC/AE back on..  all without releasing reset and keep holding in for about 10sec. The time is not important.. it is the front LED rapid flashing that indicates you are in factory mode.
    Release reset.
    If it doesn’t flash rapidly you have released reset at some point and try again.
    Be Gentle! Feel the switch click on. It has a positive feel..  add no more pressure after that.
    TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations.
    No files are deleted on the hard disk.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
    2. Make sure ipv6 is set to link-local only.
    3. After the reset the TC will appear in the WiFi as a new device. And in the Airport utility as Other Wi-Fi Devices (1) which you click.. from upper left corner of the AU.
    4. No luck do it the hard way. Or what I should say.. is the exact manual method that brooks no exceptions due to lousy networking in Mavericks.
    Plug the TC into the computer by ethernet.. make sure IPv6 is also set link-local only in the ethernet interface of the computer.. and simply do full manual setup. Turn wireless off in the computer. You can do this in full network isolation.. ie TC plugged into computer. Start with factory reset.. that is assumed before the following steps.
    These are the steps for manual configuration.
    1. Make sure you are getting an IP in the computer from the TC.. the router must show 10.0.1.1 after a reset. The computer will be 10.0.1.2
    2. Open the airport utility and go to the top menu area. Open File / Configure Other.
    3. Type in your IP address.. after a factory reset there is no password required. But if it complains it is public
    Click ok.
    4. You will then get the full edit screens where you can manually setup the TC to whatever you want.
    5. For mavericks I strongly recommend changing to all SMB compatible names, ie short 2-20 characters.
    No spaces and Pure alphanumeric.
    eg
    6. Use same rules for wireless. Set security to WPA2 Personal..
    use a password of 10-20 characters mixed case and numbers... but still pure alphanumeric.
    You can use a different name for 5ghz if you want.
    You can also set channels at least for 2.4ghz I am not sure if 5ghz is relevant for AC models.

  • HT4145 Does this article apply to OS X Lion and Airport Utility 6.0?  Reason: Airport Utility cannot find my Airport Extreme (4th generation) wirelessly on my Time Capsule configured network even although the firmware in both units is up to date.

    Does this article apply to OS X Lion and Airport Utility 6.0?
    Reason: Airport Utility cannot find my Airport Extreme (4th generation) wirelessly on my Time Capsule configured network even although the firmware in both units is up to date.

    I thought you were trying to Extend the network with an Express as the article mentions you pointed to...
    You can't find the Airport Extreme then...
    I woudl suggest doing a Factory reset....
    http://support.apple.com/kb/HT3728
    Then you should be able to set it up just as you did when it was new....
    Factory default reset (using reset button)
    If the AirPort Base Station or Time Capsule isn't accessible from AirPort Utility, the Factory Default reset can be accomplished by using the reset button.
    Unplug the AirPort Base Station or Time Capsule from power.
    Press and hold the reset button with a pen or pencil, then plug the AirPort Base Station or Time Capsule back in while continuing to hold the button until you see the light (LED) flash rapidly. This should happen after a few seconds.
    Release the button. This will factory default reset the AirPort Base Station or Time Capsule.

  • HT1178 my airport utility cannot find my Time Capsule

    My time capsule is connected to my mac pro but in trying to set it up my Airport Utility cannot find it.

    Connected by ethernet?
    Airport turned off?
    No other connections .. do it in complete isolation.
    Do factory reset. That will not harm the backups at all. But it will get the TC functional if that is possible.
    If you have issues.. please give us info on the ethernet setup in the computer.. it should be set to dhcp and get IP from the TC.. 10.0.1.2

  • Cannot set up Time Machine because Airport Utility cannot find it.  What do I do now?

    Sorry, I meant to say Airport Utility cannot find Time Capsule.  The TC is not listed as an available drive in the TM setings panel.  Trying to set up a MBP.  iMac TM settings panel lists TC but if I search for it from either machine, iMac or MBP it is not found.  Repeated rescanning doesn't find it.  Also trid Airport Utility from iPad and iPhone, still not found.  When I first purchased it I set it all up so I have logged into it before.  That was a couple of months ago, now I've got around to setting up TM I can't access it.  It is continuing to provide my wireless network though.

    OK, turned off all devices, pulled the plug out of the TC, waited then plugged back in.  Started everything up again and Airport Utility can now find the TC.
    Thanks to you both for trying to help.  Next time I'll try this first but it didn't seem like a very elegant Apple solution to the problem.

  • Airport utility cannot find my Airport Express, repeated rescans, nothing, even with direct connect via Ethernet. Help!

    I use Airport Express to stream iTunes to my home stereo. This is the ONLY thing I use it for. It quit working and now Airport Utility cannot find the Airport Express unit, even after repeated re-boots of all components, resetting the Airport Express, even when connected directly to my router via Ethernet. I use a D-Link wirless router.
    I downloaded the latest Airport Utility, but it will NOT work with XP (from the Apple website, not my words).
    The Airport Express will achieve a solid green indicator after reset, but Airport Utility cannot find it. Until Utility can find and recognize the Airport Express hardware, I cannot adjust or reset any settings, etc.
    Help!

    I downloaded the latest Airport Utility, but it will NOT work with XP (from the Apple website, not my words).
    The latest version of AirPort Utility.....5.6.1.....will only run on a Windows 7 machine.
    Try AirPort Utility 5.5.3 for Windows (make sure that  you have Service Pack 3 installed on your PC, otherwise the application will not run on an XP machine).
    The Airport Express will achieve a solid green indicator after reset, but Airport Utility cannot find it.
    After a "hard reset" or "factory default reset", the light will not be green.....it will be slowly flashing amber after it restarts. See this Apple support document for more information on various resets:
    Resetting an AirPort Base Station or Time Capsule FAQ

  • Airport utility cannot find Extreme nor Express, but internet is working?

    I have an airport extreme base station and and airport express (as a wireless extender and media speakers)
    When my iMac wakes up from sleep, airport utility cannot find any devices.
    - internet works as usual
    - airplay doesn't work (via my ipod or my iphone)
    - apple TV 2 can't find the itunes library.
    - in system preferences -> network - my network seems to be all ok and when I turn off airport and on again, both devices suddenly appear in the airport utility. But when the iMac goes to sleep, same problem happens.
    - I have made ensured that my network is the preferred network but still the problem persists.
    as the internet is working, there doesn't appear to be a problem. However, when airplay and apple TV are not working properly, this is a problem!
    Grateful for any help. Thanks.

    My Airport utility cannot find my base station either, and I can't print. But I can access the Internet!
    The base station just "vanished" one day after working perfectly for about two months. I first discovered this when I was unable to print - I began troubleshooting by entering the utility, only to discover the base station was not listed.
    I finally deleted my networking settings in Vista, and then did a factory reset on the Aiport Extreme. I then set everything up from scratch again to successful resolution.
    Then again one day a short time after that, it vanished again! In frustration, I disconnected Airport and put it away. I tried setting up a new Dlink I purchased to replace the Airport, but the Dlink didn't work either!!! Dlink tech support couldn't fix the problem and suggested I get my money back. I then, as a last ditch attempt, reconnected the Airport. It automatically found the base station without me doing anything besides just hooking it back up!
    It worked for about two weeks and now it vanished again! The utility upgrade released the other day has not fixed this problem. I guess I'll delete networking connections again in Vista, and do a factory reset to Airport again.
    I guess Airport and Vista just don't play well together.

  • Airport Utility cannot find my Extreme base station but everything works!

    I must be going crazty, but I can't figure this one out. I've had my Extreme and Express configured since November of 2007. Airport Utility would always find them and let me look at the configuration. I don't believe that anything major has changed on my laptop. Today I went to run Airport Utility and it cannot find my 2 stations. Again, everything is working, I can surf the net, from various laptops throughout my house.
    I had to do a factory reset to the extreme, and thankfully I remembered the 10.0.1.1/public and was able to reload a baseconfig I had. After this I still couldn't find the extreme nor the express with Airport Utility.
    Does anyone have any suggestions? Why would Airport Utility stop finding my stations?
    Any help would be amazing.
    Thanks,
    Frank

    My Airport utility cannot find my base station either, and I can't print. But I can access the Internet!
    The base station just "vanished" one day after working perfectly for about two months. I first discovered this when I was unable to print - I began troubleshooting by entering the utility, only to discover the base station was not listed.
    I finally deleted my networking settings in Vista, and then did a factory reset on the Aiport Extreme. I then set everything up from scratch again to successful resolution.
    Then again one day a short time after that, it vanished again! In frustration, I disconnected Airport and put it away. I tried setting up a new Dlink I purchased to replace the Airport, but the Dlink didn't work either!!! Dlink tech support couldn't fix the problem and suggested I get my money back. I then, as a last ditch attempt, reconnected the Airport. It automatically found the base station without me doing anything besides just hooking it back up!
    It worked for about two weeks and now it vanished again! The utility upgrade released the other day has not fixed this problem. I guess I'll delete networking connections again in Vista, and do a factory reset to Airport again.
    I guess Airport and Vista just don't play well together.

  • Airport Utility cannot find AX base station

    I can see that this is unfortunately a widespread problem, but I wonder if anyone has found a solution. I am running a wireless network with Airport Extreme and iMac (and several Windows laptops). Most of the time it's fine, but twice have I encountered that after shutting off modem and AX that the airport utility cannot find base station even though it is sitting right next to iMac. Also, all lights are solid green, both on modem and AX. I can find loads of other wireless networks, just not my own. No combination of resetting, restarting or reconnecting seems to do the trick and it get's very frustrating! If anyone has a solution, let me know.
    Thanks!

    Have youi tried maybe running an Ethernet cable from the AX to the Base Station to establish the connection and then removing it (or reconfiguring the wireless network) ?
    DaleB

  • How do I connect to Time Capsule from a Windows 8.1 machine which is on a Windows domain. I have been able to connect from a Windows 7 machine on a Windows domain to a Time Capsule. Airport utility is not displaying the Time Capsule Win8.1 machine

    How do I connect to Time Capsule from a Windows 8.1 machine which is on a Windows domain. I have been able to connect from a Windows 7 machine on a Windows domain to a Time Capsule. Airport utility is not displaying the Time Capsule Win8.1 machine.
    I have checked that the firmware has been updated to 7.6.4 . Similalrly the Win8.1 machine has been loaded with the update specified in another discussion.

    Firstly how are you connecting to the TC.. wireless or ethernet?
    Please open a command window and ping it.. ping by name and by IP address.
    If ping succeeds at least by IP it should work.
    In windows explorer type
    \\10.0.1.1 (or whatever the TC ip is.. that is the default).
    Having the airport utility for windows loaded can help the process. As it loads bonjour for windows.
    7.6.4 firmware on the TC is useless. It works better on 7.6.1
    If the ping does not succeed by either name or IP address yet you have internet through the TC, then your network is setup wrongly. You are have firewalls blocking local IP. Take down all the firewalls.

  • Airport utility cannot find base station

    Hello. I upgraded to Leopard. I have normal internet access from airport extreme but airport utility cannot find my base station. How can I re-establish contact? Thanks

    Which base station do you have?
    The "AirPort Utility" is only compatible with the round 802.11b/gAirPort Extreme base station (AEBS), square 802.11b/g/n AEBS, and AirPort Express (AX).
    It is not compatible with the older graphite 802.11b AirPort base station (ABS) nor the dual-Ethernet (aka "snow") ABS.
    If you have a compatible base station, have you tried doing a reset on the base station and perhaps temporarily connect your computer via Ethernet to the base station?

  • HT1349 Airport Utility cannot find my Extreme or Express?

    Airport Utility cannot find my Extreme or Express?

    Hi, found an answer to this on web
    1) Ensure that AE is sending a signal out (ca. 45s after at reset)
    2) To see this signal first go to the wifi and connect to the net that AE send out - name: "Apple xxxxx.."
    3) Start up Airport Utility and AU will now see your AE
    Finish and configure

  • Airport Utility cannot find Time Capsule and has a blinking amber light

    I have a wireless router for my Wifi set up through AT&T (2WIRE). I am trying to add my TC to my existing network rather than establishing a new Wifi network with it. When I try to plug in my TC to set it up, Airport Utility cannot even find it. My TC has a blinking amber light also. I have tried reseting my TC, resetting my router, unplugging my router, unplugging my TC... I have the latest version of Air Port utility (6.2 (620.33)).

    Connect the TC LAN port to the computer by ethernet.
    If necessary do a reset of the TC so it shows up.
    Put the TC into bridge mode.
    Go to the wireless page, and set wireless to off.
    Update the TC.. disconnect from the PC and plug WAN port to LAN port of the 2wire with ethernet.
    The TC will now exist as a client in your network without creating a second wireless network.
    You should also be able to access the TC via the airport utility.
    I do think you should use the TC wireless since the 2wire does not provide a signal at 5ghz which is much faster than 2.4ghz.
    So I do suggest you in fact do use the wireless but it is up to you.
    It makes no difference having two wireless networks if they both connect back to the same router.
    Do not use the "Join a wireless network" method.. ie no cable between the TC and 2wire.. that is poorest possible setup.

Maybe you are looking for