Airport (via Keychain I think) Keeps Changing My Wireless Network Key

I think my airport express utility is is changing the stored 128 bit WEP key for my XP wireless utility. Is is possible that this could happen via keychain? If so, how do I delete keychain entries in windows XP? Thanks.

It is asking for your security phrase not the router's password, in case you are entering the wrong password. If you are sure you are entering the correct phrase, you can reset your router to factory defaults then set up your security again.

Similar Messages

Airport Express as an end point on a wireless network and connect a computer via the ethernet port?

Can I use my Airport Express as an end point on a wireless network and connect a computer via the ethernet port? - I'm wanting to connect a computer that does not have wireless and is in another building.

The requirements for this to work are:
1) The AirPort Express must be the 802.11"n" version. Model Number is A1264
2) There must be adequate wireless signal stength where the Express will be located
3) The Express must be configured to "join" the wireless network with the option checked to activate the Ethernet port

This AirPort base station was unable to extend the wireless network.

I have an AirPort Extreme in the lounge connected to BT infinity.
I also have an airport express in the kitchen connected to a stereo system.
I have had this set up for around 12 months.
The airport express will not extend the wireless network.
I reset it, restart, factory reset etc and it will work fine for around 3 days, then I get the same error message saying
This AirPort base station was unable to extend the wireless network. Make sure the wireless network you’re trying to extend was set up and is working correctly, that you entered a matching wireless network password into this device, and that this device is in range of the wireless network.
The express is situated easily within range of the extreme. And the airplay between those two, my iMac and two apple tv's works pretty much as it should.
Can someone please shed some light on this?
Maybe I have it in a wrong setting or summut....

G Beach wrote:
I am also experiencing a recent failure in my Airport devices no longer extending my wireless network.
My Aiport Express and second Airport Extreme were extending my wireless network for more than a year
The only change that has taken place lately is that the firmware for both devices was upgraded to 7.6.4, however the upgrade was only in response to trying to resolve this problem. Needless to say, the firmware upgrade did not resolve anything.
If I didn't know better, I'd have thought I wrote the above.
I have a TC from a few years ago (last one before the tower, I think), plus the older AEBS that it replaced extending the network, plus a 1-year-old Express also extending. I had upgraded them all to 7.6.3/4 when it came out, but reverted them all to 7.6.1 when everything went crapways (others having the same issues of the LAN regularly croaking), and didn't bother upgrading again since.
Today I just tried 7.6.4 on all of them, and it seemed OK at first with green lights all around in Airport Utility. Then I made one change, which was to enable 5Ghz on the main AEBS/TC only (the express doesn't need it, and the older AEBS can't do it).
The latter two started flasing amber and giving the "unable to extend wireless network" error message.
So I'm wondering if you are similarly using 5Ghz?

Airport Express (1st generation) does not reconnect to wireless network after router is cycled on/off

Operating System: os x 10.9.1
Airport Utility 6.3.2
Airport Express 802.11n (1st generation)
Linkus router: Model WRT310Nv2, Firmware Version 2.0.01
Motorola Cable Modem: Model 2210-02, Firmware 7.7.3r5
The Airport Express (AE) is setup to join my wireless network using Airport Utility. A printer is connected to the AE with a USB cable. After the setup the AE light is green and the printer can be accessed over the wireless network.
The problem starts if the router is cycled off/on. Now the AE will not rejoin the wireless network and there is a non-flashing amber light. If the power to the AE is cycled off/on the AE reconnects to the wireless network.
This is about as handy as a screen door on a submarine.
Is it possible to see the setting of the AE the same way the modem and router settings can be accessed? Can this issue be fixed?

If they send you a replacement printer it will have ink tanks with it. You can store the ink tanks from your current printer and use them later on you "new" printer if you wish. Store them nozzle-up so they do not leak.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

My C7280 keeps dropping the wireless network but my C7180 is okay

My C7280 keeps dropping the wireless network but my C7180 is okay both have set IP addresses, both in same room and the C7280 has to be setet to see the wireless. It will work okay all day but the next day it has dropped the network.
Any ideas

What operating system? There is an update for "Windows 7 Critical Update to enhance reliability of network connection", the version for 64 bit Windows 7 is here. If you have a different operating system check HP's download page for your appropriate operating system and look for updates.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

I have an Airport Extreme which I'm using for a wireless network. Can I also plug in my iMac to one of the free ethernet ports on the Airport Extreme to connect to the Internet that way? Thank you.

I have an Airport Extreme which I'm using for a wireless network. (The wireless router is connected to a DSL modem.) Can I also plug in my iMac to one of the free ethernet ports on the Airport Extreme to connect to the Internet that way? Thank you.

Yes, you can.

HP Laserjet CP1025nw keeps disconnecting from wireless network

I just purchased this printer yesterday and have had no luck getting the wireless network connection to stay connected for longer than a few minutes. Currently it's connected to my cisco router via ethernet and works great connected that way. I can AirPrint from all my IOS devices and from my Macbook Air and Windows 7 laptop.
I am able to get the printer to work on wireless for a short period of time - roughly 10 minutes or so. I have sent test prints from my IOS devices as well but eventually the blue wireless light on the printer begins flashing and that means it has lost it's connection. Restarting the router and printer will get the wireless back online for a few minutes and the problem comes back. I read somewhere that power cycling is a "solution" but I don't agree.
Now, I suppose I could leave it plugged via ethernet cord, but I specifically bought this printer for it's wireless printing capability and would have liked the option of moving it to another location away from my router if need be. It should work as advertised in my opinion without having to reset/power cycle anything on a regular basis.
My dad bought the same printer as it was on sale. He has asked me to set it up but hopefully he hasn't opened his box yet. I know he is hoping to use the wireless function due to the spreadout floorplan of his home office.
I have updated the firmware on the printer (and router) to the latest version and set a static IP address as well. DHCP yielded the same results. Following some advice on this forum I have even disabled SNMP though I don't think that would be the problem.
Any thoughts? Is HP even planning on providing future support in the form of firmware updates now that the printer is a pretty much a clearance item?

Hi hp_ik
I understand the printer keeps losing the network connection.
I will be happy to assist you with this.
I have provided a document for the printer not maintaining a wireless connection.
I would setup the static IP for the printer to see if this will resolve the issue.
It may not be the printer, it may be your router's inability to wake the printer.
What router are you using?
Can you get into its settings?
If you can then look for and enable "Multicasting".
If not you will have to contact the router company.
Disconnect the routers power cable, wait 10 seconds, then reconnect the power cable. Wait till it's ready.
As a troubleshooting step, try connecting the printer to the router via an Ethernet cable (cat5). This is just to find out if the printer and the router are having problems communicating via wireless.
If you need more assistance just let me know.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Airport does'nt want to connect to ANY wireless network

hello there.
once more someone writing who is experiencing problems with the macbooks incorporated airport.
after joining a 3rd party wifi and returning home, my macbook is unable to connect to ANY wifi network. the bar is completely grey, but airport finds all available networks. in the network dialog appears "airport is active, but not connected to any network", indicated by a red lamp. i am also not able to connect to my network's router typing its local ip in the browser.
rebooting hundreds of times, removing all networks from the list and re-adding my WEP-secured home network did not solve the problem.
i also tried almost all solutions apple offers to fix airport problems including installing the newest firmware, but all this resulted the same.
in the diagnostics, airport seems to work normally, exept that i cannot connect to any network. furthermore, now my macbook does not accept the (correct!!!) WEP for the wifi, telling me that it is invalid - i tried it with and without the "$" in the beginning.
does anybody have an idea how to bring me back online?
gracias, benbanderas

IM having a very similar problem myself! i have my Macbook for around a year now and i have never actually had any problems with it apart from the wireless connection. my router is a speedtouch 576 and i have never been able to pick up a signal.
I dont fully know how to connect it to a wireless network even if there was signal because I have never been able to go online wirelessly. when i do get a signal a bar appears then disapears several times and when i try to connect it says password is wrong even though it might be correct (using all different 128's and using the $ )
not sure if it is a hardware roblem but I wondered if i could take it to an apple care store and see what they think about it. perhaps thats the best thing you could do if you have applecare?
Jono

How do I use Airport Extreme to create wired access point on wireless network?

Bit of an odd situation. I just went from cable to DSL at home and the modem moved from right by my computer to upstairs.
Trouble is, there's no real easy way to get a cable from the modem upstairs to my X-box (sans wireless connector) downstairs.
I could buy the wireless adaptor for the X-Box, but I was hoping I wouldn't have to spend any more money.
I have my airport extreme, and I was hoping I could use it to create a wired access point on the network, recieving the signal from the wireless modem upstairs and allowing me to plug in the X-Box.
Is this possible? If so, how? I've been through the config panel about a dozen times, but can't figure out what combination to set up.
Thanks.

Will it work if I use the express to create the network?
Yes, providing that you have an 802.11n version of the AirPort Express and the Express has been configured to "Allow this network to be extended".
Then, the AirPort Extreme can be configured to "extend" the Express network. When you do this, the AirPort Extreme will provide more wireless coverage and the LAN Ethernet ports are enabled, so you can connect an Ethernet device.
This will not be a "normal" Ethernet connection. It will only work as well as the wireless "hop" between the Express and Extreme allow.
For best results and performance, a wired connection through the hole in the wall is always best. If you decide to do this, you will need the "new" AirPort Express with both a WAN and LAN port on the device. But, you could try wireless first to see if it will meet your goals before you reach for the tools.

How do I resolve error 10057 when trying to set up my airport express to extend the range of my wireless network

I have a Dell XPS running on Windows 7 and use an AirPort Extreme 802.11n Wi-Fi to get wireless internet access for other laptops in the home. I want to connect an AirPort Express 802.11n into the network to wirelessly extend the range of my wireless network. I have installed the AirPort Utility but when I attempt to connect to the AirPort Express, it gives me an error code 10057 and says I should check the internet connection. I have tried resetting the TCP/IP settings on my PC but that did not fix the issue. The Airport Express is also flashing yellow rather than solid green. Has anyone found a fix for this issue?

This sounds as if you have an older AirPort Express that is no longer supported by the newer Mavericks operating system.
To check and see if that might be the case, locate the model number on the side of the AirPort Express. It will start with an "A" followed by four numbers. Hard to see in the faint print.....so you may need reading glasses or a magnifying class to see the model number clearly.
Model numbers A1084 and A1088 of the AirPort Express are no longer supported by AirPort Utility in Mavericks.
You will need to use a Mac running Leopard, Snow Leopard, or a PC to be able to administer the older AirPort Express.

Adding Airport Express to an existing Windows WEP enabled wireless network

I have can't find anything to help me add my new Airport Express to my existing WEP network. All I want is to use to play my Itunes through the sitting room stereo. I've upgraded the firmware on my Netgear 802.11b wireless access point so I can have a 13 digit WEP password. I've installed the latest install software from the apple website for the express box.
I can access the express box fine on its own but not add it to the existing network. Now the only thing that works is the apple connection! My old wireless network has stopped working. I tried the same at my office yesterday and the only way to resolve the situation was to uninstall all the Apple software and then my Wireless network was able to work again. I'm pulling my hair out here and getting in to trouble with the rest of the family because it is taking so much time up!
Someone mentioned somewhere some new firmware - I can only find one for MAcs not PCs - I don't have any Macs on my network.
Please help.
THANKS

Make sure you have installed at least Airport 4.1 on your PC:
http://www.apple.com/support/downloads/airport41forwindows.html
Most Netgear wireless routes will tell you the hex equivalent of the plain text WEP password you enter into it - and this is found using the same web browser based process you use to configure the router. This information cannot be found by any other means (like "pinging" the router's IP address). If you can get the WEP key in this manner, configure the Airport Express with the same WEP key *while it is still cabled to the router*.
The alternative is to come up with a 26-digit hex format WEP key of your own choosing. You can then wirelessly access the Airport Express and enter that WEP key on it first, followed by doing the same on the router second.

Can I use the Ethernet Port for a computer when it is also used as a wireless network with an Airport Extreme as the access point for the wireless network

Can I use the Ethernet Port of the A1264 Airport Express to connect to the Ethernet port of a computer that does not have wireless capability when the Airport Express is also used on a wireless network with an Airport Extreme 5th generation as the access point for the network?
I have AE 5th gen
looking to buy (from ebay) the AEX A1264
Various computers, printers and hubs for the network
Is this possible to do?

Bob, Thanks for the info. I have read different articles that said yes, but I wanted to make sure before I commit to buy. I have an older A1084 which I could not use the Ethernet port. I know at one point I was able to when I was on 10.4. Now that I am on an Intel processor and 10.8 I am going to have to upgrade some of my Apple wireless hardware.
Thanks Again.

Airport error when attempting to import photos across wireless network

Hi,
I'm using the latest version of iPhoto '09 on a MacBook that's connected to my home wireless network through an Airport Extreme. Also on the same network is a brand new Mac Mini. When I attempt to import photos into iPhoto '09 on my MacBook from the Mac Mini, I get an Airport connection error that I dismiss by clicking OK. Immediately after clicking ok, I then get a "Can't find the original photo..." error and I hit cancel. I do this three times and presto the photo imports itself. This occurs every time I attempt to do an import.
My network is not dropping. My Internet connection is not dropping. My MacBook and the Mac Mini stay connected continuously so I'm not sure why I get these errors.
Any thoughts?
Thanks,
Mark

It has nothing to do with the Airport connection.
This sometimes occurs if you’re importing a file into iPhoto and there’s already a file there with the same name. Digital cameras can produce many, many files with the same name over their lifetime, so it’s not uncommon to have several files called IMG_00543.JPG, for instance. Now you want to import one also called this.
What happens is that iPhoto compares the two files to check for duplicates. However, if iPhoto cannot find the file already in the database for comparison, then you get this message. It suggests that your database is damaged because iPhoto has lost track of this (or these) similarly named files.
A simple test is to rename the file you are importing - just add a character - IMG_00543a.JPG for instance. If this then imports with no issue then you might consider rebuilding your library:
Download iPhoto Library Manager and use its rebuild function. This will create a new library based on data in the albumdata.xml file. Not everything will be brought over - no slideshows, books or calendars, for instance - but it should get all your albums and keywords back.
Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one.
Regards
TD

Can either the Airport Express or Airport Extreme be used "standalone" to create a wireless network with access to the internet?

I want to create a wireless network for my iMac, Macbook Pro and iPad, and I'm confused about the Airport Extreme and Airport Express devices.
There is mention for both about connecting them to a DSL or Modem. Does this mean I have to obtain additional hardware before they will enable connection to the internet? (In the past, I've used a Belkin Router, which simply connected to the phone line.)
Any advice gratefully received.
Tony

Does this mean I have to obtain additional hardware before they will enable connection to the internet?
Yes, you need a modem. The AirPorts are routers only. They do not have a modem built in, so you will need a modem if you want to be able to connect to the Internet.
The Belkin device that you have used before is a modem/router. It combines the functions of a modem and router in one package.

G4 (MDD) with AirPort Can't See/Won't Connect to Wireless Networks

Hi all. I've seen topics/threads that get close to my question/problem, but not quite.
I inherited a PowerMac G4 (MDD)/Dual 1 GHz/1.5 GB DDR SDRAM/running 10.3.9.
I purchased a used original AirPort card from eBay, opened up the machine, and plugged it in. When I went to update the software (from a CD), my machine told me that it was up to date (though one HD is running OS9 and one running OSX -- so the software wouldn't install because the HD running OSX said it was up-to-date and the HD running 9 said it was impossible). The machine recognizes the card/shows it gray in the toolbar/says it has Firmware Version 8.70 in the System Profile.
My problem is that the AirPort can't see any wireless networks 99% of the time, even though 3 (including mine) are in range all the time. I've seen my network only flicker into possibility a few times, and even though I've disabled all security measures on the wireless router (Linksys Wireless-G, Model WRT54G), it simply won't connect. One time in 3 hours it momentarily looked like it was going to connect, then said "out of range," then disappeared completely. It has seen 0 wireless networks for the past hour.
I've read everything far and wide trying to solve this issue and am totally stuck. At first I thought I needed an antenna for the AirPort, but this is an internal card, so that doesn't seem right. I know the AirPort card (and not Extreme) is right because a) I don't have a FW800 port and b) the machine recognizes this card. Finally, I thought it may have had to do with the WPA security on the Linksys, but even with security disabled...nothing.
I'm feeling very frustrated. Any advice?
Thank you very much.

Thanks, Tom. I did as you suggested, and the Max Signal under the Log is showing a red 12, which is terrible, yes? What, exactly, does this tell me? That this is simply a case of old technology (AirPort b) struggling to communicate with new technology (Linksys g) over a medium distance (Linksys is in next room, through wall)? If plugging straight into the ethernet were an option, I'd just do it. But I can't get my G4 onto the Internet without running cords down the hallway and through my TV room, which is an obvious eyesore.
Is there a chance this AirPort card is only partly functional and I should return it? Or do I need to accept the fact that this G4 needs to either be moved closer to the Linksys router or be plugged in directly?
Thank you.

Airport (via Keychain I think) Keeps Changing My Wireless Network Key

Similar Messages

Maybe you are looking for