Airport WEP keeps getting lost after reboot

Every time I reboot the WEP connection is lost.
How can I set this up so it stays after a reboot and connects automatically?
Thanks

Delete the WAP from your list of preferred networks and also delete it from your keychain using Keychain Access. Then re-add. I had to do this for bith a WPA and a WPA2 access point. Funny thing is that after upgrading to 10.4.8 it took two days for the WPA account to start misbehaving and another 4 days till the WPA2 one started dropping. Deleting completely and re-adding them fixed it both times.

Similar Messages

Microphone +20 Boost keeps gets unchecked after rebooting pc..

Everytime I reboot the mic boost keeps getting unchecked. I have the latest drivers for X-Fi and Vista 64 SP. Please help.......very annoying!

But, there is a catch : if You're using PC's case front panel connectors for headphones(for sure Audigy, don't know with X-Fi, but probably the same result) and You'll prevent cthelper from starting, it will disable autodetection of headphones by Your card.
It was so in my case.
However, I confirm - removing cthelper from Your startup really helps Your Mic

Account Information Keeps Getting Lost After it is Saved

At my office computer we have an iTunes account that is to be used at our office as well as a couple places around the world. We have entered in all of our credit card and billing information and yet, after we sign out and sign back in, when we try to purchase a song and put in our login and password, we are taken to an account verification page that, even if we verify, does not allow us to purchase a song. We have reset iTunes and re-entered the credit card information fully. What could be the cause of this. The work computer I use does use Vista. Any thoughts are appreciated.

Delete the WAP from your list of preferred networks and also delete it from your keychain using Keychain Access. Then re-add. I had to do this for bith a WPA and a WPA2 access point. Funny thing is that after upgrading to 10.4.8 it took two days for the WPA account to start misbehaving and another 4 days till the WPA2 one started dropping. Deleting completely and re-adding them fixed it both times.

When trying to connect airport express keep getting unexpected error please try again. IVE TRIED A HUNDRED TIMES AND HAVE FOUND SUPPORT PAGES UNHELPFUL

when trying to connect airport express keep getting unexpected error please try again. IVE TRIED A HUNDRED TIMES AND HAVE FOUND SUPPORT PAGES UNHELPFUL

Have you tried using a WEP password for your wireless network instead of a WPA one? That fixed it for me.

HKLM Permissions lost after reboot

Hello All.
I have a need to give the Everyone group full control over the root HKLM hive of the registry. I have used the RegEdit GUI and the regini command to grant full control to the Everyone group for the HKLM Key and Subkeys. However, once I reboot the workstation,
the permissions have reverted back to the original.
The local administrators group is the owner of the HKLM key, and I am logged in as a member of this group when making the permission changes. I have UAC disabled, and have tried regedt32.exe > Run as Administrator and cmd.exe > Run as Administrator,
and I can set and confirm the permission changes with error, but the changes are lost after reboot. No AV is installed.
Does anyone have any clue what I am missing here?
Thank you in advance!

Hi,
I cannot repro such issue on my computer. This should be something wrong during restarting or the admin account.
If you have any other admin account, please log on with it and try to grant the permission you would like to see what’s going on.
To make sure that other program reset permission during restarting, please test this issue when booting into Safe mode and let me know the results.
If the issue still persists in safe mode, please help to collect the boot trace for further research.
How to collect a good boot trace on Windows 7
http://blogs.technet.com/b/jeff_stokes/archive/2012/09/17/how-to-collect-a-good-boot-trace-on-windows-7.aspx
Once down, please upload the .etl file into SkyDrive or Similar ones and share the public link here for our research.
Keep post.
Kate Li
TechNet Community Support

Hyperlinks from other placed indd documents or pdfs getting lost after export to PDF

after upgrade vom CS 5.5 to CS 6: hyperlinks from other placed indd documents or pdfs getting lost after export to PDF
I tried all options for the as well known and working export options

after upgrade vom CS 5.5 to CS 6: hyperlinks from other placed indd documents or pdfs getting lost after export to PDF
I tried all options for the as well known and working export options

The password file is getting corrupted after rebooting the standby database

Hi,
The password file is getting corrupted after rebooting the standby database.
Since the databases are not in sync, I had to copy the pwfile from primary to standby to make 'em sync.
(BUT.... the pwfile is not getting corrupted every time I reboot the standby by)
Could somebody please explain the reason for the pwfile on the standby database getting corrupted while rebooting ?
Env: Oracle 11g on Windows 7
Thanks in advance

Moderator Action:
This thread was originally posted to the Oracle/Sun Servers HARDWARE forum.
This is definitely not an issue related to any hardware components.
... it's now moved to Database General Questions, hopefully for closer topic alignment.

Aperture 3: GPS data gets lost after 'Update from Master'

My library contains photos in JPEG format that I geotag in Places, then I save the metadata with 'Write IPTC Metadata to Master'. The problem I have is, that the GPS data gets lost after I do an 'Update from Master', even if I saved the metadata before. I'm having this problem with referenced and managed photos and all my JPEGs from several different cameras. The only way to permanently store the GPS info into my photos seems to be to export the geotagged photos as versions.
Does anybody has the same problem or knows how to solve this?
Thanks in advance,
Michael

Use Houdah geo (http://www.houdah.com) to write location data back to the EXIF. It's interface is very similar to Places (Google maps and pins) and you can interface with the Aperture library. It's a bit of a pain, but if you need it done now rather than wait for an Aperture 3 fix, then...
Also, see here: http://www.nickrains.com/index.php?option=com_content&view=article&id=65:apertur e-3&catid=12:news&Itemid=24

Why does my storage keep getting filled after deleting everything?

my storage keeps getting filled after I delete most of my apps, photo, etc. Im pretty sure it had something to do with the new update because it was fine before. please help its really bugging me and I cant even go on some of my apps because I don't have enough storage

While it's normal for your charger to feel hot due to its function, sometimes there's too much heat.
If your charger becomes so hot that you cannot touch it or you note a strange smell, your charger is malfunctioning and should be replaced.
A charger that malfunctions could damage the iPad battery, which also may need a replacement.

ITunes settings lost after reboot

I have a problem where after a reboot the settings of iTunes are back to default. For example:
it loses the account for the Store (I have to re-enter email address and password);
it loses the wifi sync settings for my devices
it shows the iTunes tutorials screen, as if I'm starting iTunes for the first time
settings under preferences are lost
Other things are not lost:
the library is still there;
iTunes remembers the devices (when connecting it is handled as a known device) and knows what playlists/apps/.. to sync with it.
Since I'm not rebooting my Windows 7 PC a lot, the problem is not occuring a lot, it doesn't keep me from using iTunes, it is just annoying. Now after rebooting I decided it's enough and I would post the issue (since I can't seem to find a comparable issue).
Also worthwile noticing is that the problem is already there for some time, though I can't exactly pinpoint anymore when it started. Possible when iTunes 9 or 10 were realeased.
Now I'm using:
Windows 7 64-bit (completly up to date)
iTunes 10.5.2.11
Thanks for any help!

Router>sh ver
Cisco IOS Software, 1841 Sofware (C1841-IPBASE-M), Version 12.4(7d), RELEASE SOFTWARE (fc2)
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
Router uptime is 34 minutes
System return to ROM by power-on
System image file is "flash:c1841-ipbase-mz.124-7d.bin"
Cisco 1841 (revision 7.0) with 114688/16374K bytes of memory.
Processor board ID FCZ1251943K
2 FastEthernet interfaces
1 Channelized (E1 or T1)/PRI port
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM
31360K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2142
Router>

German umlaute lost after reboot

The strange behaviour is that, after rebooting the linux server where the application is running, german umlaute are lost. If the application is reinstalled umlaute are shown as long as no reboot occurs. There was no problem with this when jre122 was used, problem arised with jre142. The data are read from a mysql database.

It seems that I have solved the problem with the character set. It's not really something that I understand but it works: I have changed the startup script that is used in /etc/init.d/rc5 to start the server. I changed the shell for the script. It was not working when I used #/bin/bash or #/bin/sh but it works when I use #/bin/csh.

Pagefile gets deleted after reboot

I have moved the pagefile to another partition and left a small piece on the system drive:
C: (Windows) 200-500 MB
B: (Temp) 4000-16000 MB
When I set the pagefile size, the pagefile gets created immediately, but after reboot it gets deleted again and remains only on the system drive. So after reboot, there is only 200 MB pagefile, not 4200 MB. And the total available memory is only a little
bigger than the amount of RAM, not 16 GB as it should be.
What is wrong? Am I missing something?
I have Win7 Pro SP1 x64, and a lot of free space on B:. Both partitions are on the same SSD disk.

Hi Xars
Thanks for your digging and we found similar cases with yours,so I tested on my own machine and turns out it is actually related to the Drive letter. Since The letters A and B are usually reserved for floppy disk drives, it's not recommended to
assign A and B to anything other than a floppy or floppy substitute even you do not have a floppy disk drive installed. I suppose Windows might not let you if you do this thinking "putting a pagefile on a floppy disk!"
We found sort of workaround for you but it still takes a lot of works, and it even need to reformat you hard disk.
Therefore, we recommend changing driving letter and we think it is the best way to avoid this kind of issue.
About Change, add, or remove a drive letter(Windows vista and 7 )
http://windows.microsoft.com/en-us/windows/change-add-remove-drive-letter#1TC=windows-vista
You could refer to similar case “Pagefile on a volume that uses "A" or "B" as the drive letter”
http://answers.microsoft.com/en-us/windows/forum/windows_7-performance/pagefile-on-a-volume-that-uses-a-or-b-as-the-drive/fdac6f23-a34d-e011-8dfc-68b599b31bf5
Regards

Qosmio X500: Lan/Internet connection get lost after period of time

Hi all,.
I got the qosmio x500 for about half a year now...
I got this problem where after about 5 hours or less the lan/internet connection get lost.
I disabled the wireless connection and is using only the wired connnection now.
When it get disconnected... all devices seems to work seemlessly, no problem can be found. I checked the win7 network adaptor --and it seems to be connected properly.
I haven't got a slightest idea how to fix that.... Only a reset of the system and reloading the os results with a valid connection.
It is even stranger,. When using it for a piriod of time (listeding to audio streams from the web)... when getting back to the machine the audio connection seems to work properly.... but when trying to access other sites, or other machines in the homegroup, or network (under explorer). It result faulty.
Please guide me somehow how to fix the issue, it is bugging me a lot (all these resets to the machine probably doesn't do it any good as well).
thanks in advance,.

Hi,
It could be the energy saving feature of your network card.
Right click Network Icon on the status bar, choose 'Open Network Center and Sharing', Click on 'Connection', Click on 'Properties' (low left button), you'll see the tab with your Network Properties. Click 'Configure' (Upper right button), choose 'Power Management' (last right tab).
Uncheck 'Allow computer to shut down this device to save energy'. Probably your problem will now be solved.
If the names I write aren't exactly right, I'm on a French language computer so my translations can be slightly wrong.
Bye,
Ton
Message was edited by: Tonio78370

Hyper-V 2012 R2 - Linux Guest VLAN Settings lost after reboot

Hi Guys,
last night a have seen a strange behavior with a Sophos UTM 9.204020 Linux Guest VM. (This VM is based on SUSE SLES v11? i think)
So i have Setup this in my home lab and experienced the same problem.
----Setup-----
2 External VM Switches
Management OS is on VLAN 4093 with IP 192.168.20.1
The guest network adapter is in Trunk Mode, VLAN Tag (4093) is set in the guest OS with IP 192.168.20.100
Everything works until you kick off a reboot from the guest or hyper-v console, after the reboot you loose the connectivity on the network adapter with the vlan trunk.
If you shutdown the guest and start it everthing works again - this happens only on reboot!!
I have tried diffrent things (static mac, enable disable hardware features (vmq/offloading etc) on the vm network adapter but always the same error.
After some search on the net i have found this article: Link
This guy has the same problem with another linux vm (based on debian) his workaround was to trigger a powershell script with the eventlog after reboot of the vm, this works for me too but this must be bug?
Has anyone else experienced this problem?
André

Hi Andre,
I would suggest you to install the supported Linux guest OS on hyper-v , please refer to following link:
http://technet.microsoft.com/en-US/library/dn531030.aspx
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

BPM: Condition gets lost after transport

Hi everybody,
we have a BPM.
When we transport the BPM from our development-XI to our test-XI the condition gets lost!!!
Strange behaviour. Any ideas?
Regards Mario

Hi Farooq,
no.
Thanks Regards Mario

Airport WEP keeps getting lost after reboot

Similar Messages

Maybe you are looking for