AirportExtreme as wireless router through DSL modem on PC - not working.
Hello all. I've searched through several forums trying to find something could answer my question, but nothing came of it. Hopefully you can help,
Our family has just recently purchased 2 new macbooks (love 'em!) and have been able to join our wirless network (linksys wireless-g 2.4ghz). A few days ago, we purchased the AEBS to replace the Linksys, however, I cannot for the life of me figure out how to make it work. The PC run windows XPSP2, using a basic DSL modem. I've tried various methods of connecting the AEBS to my computer/modem.
now, I read through the instructions to see that my PC must have a wireless card?
Am I correct in assuming that the DSL modem and the AEBS work together to put out a wireless signal, and from that, my PC uses this wireless card to connect to that?
I've tried doing a direct connection with my DSL modem and AEBS, where nothing is actually plugged into the computer. I use a USB wireless donlge thingy and it connects to the network hunky dory. However...no internet. The setup utility for the AEBS does everything all shiny but I am still not able to connect through my PC, or my macbooks. the MB's see the network, but no actual internet.
Is there a way to directly connec the AEBS to my computer and modem without a wireless card for my PC?
Thank you SO much everyones time!
A mac newbie and wireless newbie,
Ogo
In that case I would configure your network as follows.
DSL Modem -> WAN port of Airport Extreme Base Station
LAN Port of Airport Extreme Base Station -> Windows PC
The two MacBook Pros would join the network wirelessly.
Connecting a XP PC to a Airport Network via the LAN port of the AEBS
http://www.ifelix.co.uk/tech/1007.html
iFelix
Similar Messages
-
Netgear Wireless-N 300 Router w/ DSL Modem on Verizon
Before I spend any money, can anyone advise if Verizon DSL is supported with the Netgear Wireless-N 300 Router w/ DSL Modem?
Well, answered my own question. Went ahead and got one. Only had to clone the MAC address from the Westell due to the screwed up DHCP scope that is used. Works like a champ.
-
Best Router with DSL Modem for use with AT&T DSL and Airport Express?
I recently had my old 2WIRE from AT&T DSL service die, so purchased a new 2WIRE 2701HG-B. My old 2WIRE worked with my Airport Express, which is hooked up to my DVR for DirecTV use. The new 2WIRE apparently is not compatible with the Airport Express, so I returned it and purchased a NetGear Wireless-N 300 Router with DSL modem. While this one does work with the Airport Express setup, it runs very slow. This router has mediocre reviews, so I'd like to find a better one.
I'd appreciate any suggestions for a Router w Modem that would work best with my AT&T DSL and Airport Express (802.11n) within the $100 - $150 price range. Thanks!Configure the Express as a bridge: Connect via "Ethernet", and set Connection Sharing to "off (bridge mode)".
The switches ought not to be a problem, and I don't know why your router froze. The Express is simply another wired client, just like a computer might be.
do I turn off DHCP on the router,
No. Something has to provide routing functions so leave the Linksys alone. -
Hi..I have an AirPort Extreme base connected to my DSL Modem and has been working fine. But I recently bought another DSL modem along with the latest Airport Express. With this one however I can't get it to connect to the Internet. The light on the Express is flashing green though. Does it mean I have to re-set the settings on Airport Utility? I.e. the old settings haven't been cleared yet. Any suggestions?
Let's see if I can get this straight.
You have an Airport Extreme base station that is set to "Create a wireless network" and you have the box checked for "allow this network to be extended"....
Then you have an Airport Express that is set to "Extend a wireless network" which you selected the name of your network in the box...
Correct?
See this Apple document:
http://support.apple.com/kb/HT4259?viewlocale=en_US&locale=en_US
The wireless unit on the right of the diagram can be either of the newer Apple base stations.
Extreme, Express, Time Capsule -
I have been having trouble connecting to my wifi on my ipad mini but my iPod is just fine......it will connect and then say "Unable to connect to network" I've tried resetting my ipad mini and turning off my router for 30 seconds and its not working.
What TC do you have? Model number direct from the base is a big help, it will be A1 followed by 3 numbers.. eg
A1409 Gen 4.. The new AC is A1470
How is it setup?
I need the whole network setup. what modem/router, how is the TC connected etc??
I also need to know what IP the ipod gets, so I can see what mode the TC or network router is working in. -
Hi, I tried to update my iPad through iTunes but it did not work. I am trying to update to 5.0. Thanks.
Originally it said that the process would take 76 minutes but after about 30 minutes there was no longer a message giving the status of the update.
-
My 3G modem ZTE MT110 not working with mac OS X Lion
After updating to Mac OS X Lion, My 3G modem ZTE MT110 not working. When i reboot to 32 bit it works, but everytime i switch off my mac, i have to reboot to 32 bit!
Is there a compatible drive that can rum with the new mac lion?Go to:
https://discussions.apple.com/message/15748902#15748902 -
Accessing wireless router thru wired modem/router
I am running XP Home with DSL connection to the internet. I have a ZyXEL Prestige 600 modem/router. Notice that it is a modem/router all in one, not two different items. Someone gave me a used Linksys WRT55AG wireless router that I am trying to setup for use with my daughter's laptop. I have the phone line hooked to the wired modem/router and then the modem/router connected to a hub. From the hub I go to my two desktop computers. I can come off the hub and connect to the wireless router. Then I open my browser (firefox) and type in 192.168.1.1 and can access my ZyXEL modem/router. I have tried 192.168.1.2, 192.168.2.1, and several other combinations for the last two numbers. My default gateway is 192.168.1.1. My IP address is dynamic but is listed as 192.168.1.33. How do I get to the wireless router to re-do the setup?
thanks,
HaroldHookup one computer to the router all by itself via cable to one of the lan ports in back. Push and hold the reset button in back for 30 seconds, release. Now power cycle the router. Connect to 192.168.1.1 with username blank, passwork admin. Reconfigure the router to the IP you need.
-
Unable to connect wirelessly to new DSL modem - HP Deskjet 3050A - HELP!
I have a HP Deskjet 3050A J611g - I've had it a little more than a year (so out of warranty) and it has also been connected wirelessly to my HP laptop and other devices without any issues. Last month I had to get a new DSL modem from AT&T (the brand is PACE and the model is 4111N). Ever since getting the new modem my printer will not maintain a wireless connection.
I worked with AT&T tech support just after getting the modem and they were able to get me connected (they had remote access to my computer - uninstalled, reinstalled drivers, etc.) but within a few days I lost the wireless signal and cannot get it restored. I have worked with AT&T tech support for more than 10 hours - several different reps - and still not working. I have researched the issue myself, tried all of the troubleshooting steps provided by HP and others. I'm at a loss. My printer works if connected to my laptop with a usb cable but not wirelessly.
All my other devices are able to connect wirelessly to the modem, just not the printer. I'm at my wits end! What is left to try other than paying HP support for their assistance?Access your router and make sure that MAC Filtering is turned off. Also, set the encryption type to WPA2-PSK (AES) only as HP printers don't work well with the TKIP encryption type, and set the Mode to 802.11g only as that is the Mode that HP printers work best with. Being on channel 11 shouldn't hurt anything unless there is a device that uses the same channel in the area then you might get some interference. Give these things a shot, and let me know what happens.
-------------How do I give Kudos? | How do I mark a post as Solved? -------------------------------------------------------- -
Setting up Time Capsule as router with DSL Modem as bridge
Hi All,
I want to work this out in my head before I start disconnecting wires. So let me run down what the situation and plan is. If you see a potential issue, I would appreciate the feedback.
What I have:
Verizon DSL. The DSL modem is also doing duty as the router. For a lot of reasons I don't need to get into here, I no longer want the DSL modem to be the router. I have gotten instructions on how to setup the DSL modem to serve ONLY as a bridge. In that configuration, you simply connect the DSL modem to the phone line as usual, then connect your router to one of the ethernet ports. My time capsule has been serving only as a wireless access and backup drive until now. So here is what I plan to do:
1) Connect via ethernet cable, the WAN port on the TC to the ethernet port on the DSL modem.
2) Using the manual setup screen on the TC, select the "Internet" tab.
3) Set "Connect Using" to "Ethernet"
4) Set "Connection Sharing" to "Share a public address"
5) TCP/IP set to "Using DHCP"
At this point, everything should work. At least I think it should. Am I missing something?
Any suggestions appreciated.
Thanks,
RI haven't worked with the Verizon gateways, but configuring the device as a simple bridge might require that the Time Capsule be setup to furnish the PPPoE service. You won't know until you try.
If you are not able to "Connect Using - Ethernet", then that would be an indication that you would need to instead "Connect Using - PPPoE". In this case, you'll need to enter your user name and password that you have established with the service provider in the Time Capsule setup configuration. Be sure to leave the Service Name area completely blank if you setup using PPPoE.
If you are able to "Connect Using - Ethernet" and you configure the Time Capsule to "Share a public IP address", you may see a warning during setup that this is producing what is known as a Double NAT on your network. This is normally not too serious, unless you are trying to setup online gaming, which requires a different type of NAT setting. -
How do I connect my laptop to my Linksys wireless router through the internal wireless card?
I just purchased a gateway laptop and was trying to hook my Linksys wireless router up to it. Ive gotten it hooked up but only through the secondary device (that catches the signal)... I was wondering if there is anyway that I could make my internal wireless internet card a point or no? Can I only connect it to the USB network adapter or is there really a way to go COMPLETELY wireless? Thank you for your time...
Is your internal wireless card enabled? Go to device manager and make sure it is enabled.
Chuck -
Trying to get a mac on my wireless router through a pc
i am tring to get a mac computer to hook up on my wireless router. my router is hooked to a pc and i have been tring to get it on the mac but it is not reading any signals. my router is wrt54g
You may need to update the firmware of the router. Also, if you're using any wireless security, add a $ at the beginning of your password.
-
I have a new wireless router and now my laptop will not recognize the printer.
I recently installed a new wireless router,Linksys E2500, and now my laptop will not connect to my OfficeJet 4500 wireless printer. Operating system is Windows XP. Says it does not recognize the printer. It was working fine with my other Linksys router and I have been able to connect all of my other electronic equipment. Thanks.
You must reinstall the full feature software and drivers again to be sure it will work with the new router. This is the fastest way. Simply follow the instructions that came with the printer.
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired! -
Hello,
When I turn on my iPad 2 and go onto the safari and go onto google the wireless router cuts off and turns the Internet off and the Internet doesn't respond and then after I have to turn the router off and turn it on and then it is back to normal it has happening when I recently updated the new iOS 6 on my iPad since then it was been doing this please can you help and help me sort the problem out
ThanksSome things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
• Launch Settings app
• Tap on Wi-Fi
• Tap on the blue arrow of the Wi-Fi network that you connect to from the list
• In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
Westell c90-610015-06 modem & airport exteme: not working--ideas?
My Westell modem works fine, including when I hooked up a hard-wired router(Asante). I replaced the router and bought an Airport Extreme to handle wireless. Airport's status light is flashing yellow because it's confused. Is my dsl modem (provided by Verizon) not compatible w/Airport? Ideas for troubleshooting? (cables are correct; green lights for dsl/ethernet cables on Airport OK)
t.i.a.You might be DHCP in your area for DSL and now you are MAC bound. You can try and clone the MAC address of the first router or leave it unplugged over night and plug it in when you get up in the morning, that should release the lease.
Maybe you are looking for
-
Discoverer report with parameters and functions
I am new to Discoverer. Is there a way to create a report (with parameters) of one line per customer such that the following data will be displayed for each customer? Among the parameters is: from_date (month & year) ,to_date The basic query gives to
-
Why can't I copy from my WD MyPassport, external, 2TB drive? The message I get is that
-
Am having issues with optical audio on my new Apple TV. Here's the setup: - New Apple TV - Sanyo PLV-Z7000 Projector (no audio-out on it) - Link - Yamaha RX-397 Receiver (RCA inputs on the back) - Link - Digital Coax & Optical Toslink to Analog Audio
-
Windows 8.1 x64 error 0x80070002 While System Restore
Today, I downloaded a file while Widows Defender was updating and it did not warn me about a virus. Now when I try to open Widows Defender, it says Windows cannot find 'C:\Program Files\Windows Defender\MSASCui.exe' so I tried to restore. then when
-
Validating the number of columns
Hi Guyz, how can i validate the number of columns in the custom table with number of columns in flat file.. at the moment ive uploaded all the data in flat file to internal table. plz advise.. Thanks