Airpot update. sync problems. etc.

so to those of us who had this problem and had to switch off airport everytime we were using our apps, i have been reading the different discussions and people have said that there was an update released to this. however i have not seen any to download when i check my software update. i have another computer which does not even have logic and suffers from the same symptoms in other applications and when i check the software update it says everything is up-to date!
do i have to get it from somewhere else?
thanks!

In addition to power draw problems when charging from USB there are also bandwidth problems on each USB header. (UHCI) Each header controls one or two USB channels, and each channel can control multiple devices if a HUB is used.
However, the total bandwidth can never exceed 480 Mbps for Hi-Speed USB 2.0.
People who have USB external disks, or USB network controllers can easily over-run the bandwidth available on any UHCI.
I personally have never had a problem using a HUB, but all of my hubs are externally powered, and I don't have any high-bandwidth devices other than the iPhone connected to the hub.
Yours sounds like it could be more related to bandwidth than power, but who knows.

Similar Messages

App updates syncing problem

The problem of app updates not syncing properly (error messages) has been discussed before and the best solution I have seen is to remove the app and then reinstall it by syncing via the iPhone Applications tab in iTunes.
However, this has the effect of wiping any data associated with the application. For instance I have just updated eReader which has deleted all my downloaded books!
Has anyone come up with a better solution to this? Of course, the whole update process should work without any of this messing about, and I believe it does for some people. I would love to know why none of my updates now work properly whether done from the iPhone or from iTunes. Hopefully Apple will address this in a future software update.
Nick

Well all, throw my hat into the ring as well... I have an original 8GB iPhone with version 2.1 installed. the phone works great except when it comes to installing upgraded Applications. It just will NOT install the Application upgrades and I am not about to throw days worth of data that has been applied to certain Apps. So until a fix comes along I guess I will use the version I have installed. Here is the error message I am receiving:
"Some of the applications in your iTunes library were NOT installed on the iPhone "****" because one or more errors occurred. (See below):"
The application "*******" was NOT installed on the phone "****" because an unknown error occurred (0xE800002E)
In my case I had 6 updates that did NOT upgrade because of the above error. The above error code was the same for ALL of them...
Like all have said in this thread, hoping a fix comes soon and only Apple can do it, which they no doubt will, hopefully the next update they do.......................................
Gunny

After 10.5.7 update : sync problem

I have the same problem as these gentlemen.
http://www.officeformac.com/ProductForums/Office/[email protected]@
It seems to be related to 10.5.7
Never had this before.
As M$oft is mute as usual (laptop hunters anyone ?),
I thought someone could help here…
10.5.7 was made with Combo

I first removed syncing ~/Library/PubSub but this did not help too much.
I removed the contents of ~/.FileSync from clients (2) and server. Since the clients have FileVault home dirs that requires being logged in everywhere.
The old SQLite db in ~/.FileSync directory was 16MB, the new one 1.8MB. After that, I have seem an improved responsiveness. Still not something extremely fast, but good enough.
It would be good if there was some sort of 'reclaim' functionality in the SQLite db that underlies home syncing, just like there is for FileVaulted home directories.

Sync problem - earlier today I updated both iTunes and my iPod Touch. Since then, I have tried syncing the two. The iPod Touch claims that there is no music on the iPod, however, when I connect it to my computer it says my full library is on there.

Sync problem - earlier today I updated both iTunes and my iPod Touch. Since then, I have tried syncing the two. The iPod Touch claims that there is no music on the iPod, however, when I connect it to my computer it says my full library is on there. At present, I am unable to listen to songs on the iPod when not connected to the computer. What can I do to fix this?
Thanks for any help!

- Have you reset your iPod:
Press and hold the On/Off Sleep/Wake button and the Home
button at the same time for at least ten seconds, until the Apple logo appears.
- Next would be to backup your iPod and then restore you iPod from backup via iTunes.

Sync problems with new 4.3 update

I have just updated my iPhone 3gs and now I have sync problems with itunes. Eveytime I try and sync my playlist or any music to the iPhone it end up with a spinning beach ball after a couple of tracks.
Has anyone else had this problem?
I have reset my iPhone a few times now since the update but it doesn't resolve the matter.
Please help.
Kind Regards
Alan

Sorted this myself eventually. just factory restored my iPhone via iTunes. working now!

Sync problem after update

I installed the iTunes update and the 3.1 iPhone update. I had no problems with those at all. I then decided to sync my phone. My syncs usually only take a few minutes. My phone has been on "syncing iPhone" for at least an hour. It hasn't moved to backing up phone or anything.
I'm not sure whether to just let it continue or if there is something else I should do. The sync process is using nearly 100 percent of my cpu on the computer and I could barely get anything else open to get to this forum and type this message.
Any suggestions are welcome. Is anyone else having unusual syncing experience since the update? What will happen if it never progresses and I just need to unplug it? What will I need to do with the iPhone?
In my year of having the iPhone I've never had a sync problem before. Thanks for any help.

I just cancelled the sync by using the slider. I didn't realize I could do that. The phone seems fine. I may try it again and see what happens.

Sync problem after 1.0.2 update

My iPhone freezes-up when I try and sync since the 1.0.2 update.
The progress bar just shows "syncing iPhone etc" , but not sycning, contacts, music, photos, etc"
The slider on my iPhone goes dim and I have to retart the iPhone using the home and on/off button.
I have gone thru this procedure several times and now I just have it charging with the AC adapter.
Also restarted the G5, still have the issue.
Anyone else ? Possible solution ?
Thanks,
Art

I continue to have no luck syncing since going to 1.0.2
After clicking restore system, the iPhone "slide to unlock" stops and it freezes up.
I must then restart the iPhone using the home & on/off button.
As another post recommended, I deleted the 1.0.2 files from the "iphone software upades" folder,
restarted and have gone thru the above process several times, always ending in an endless
spinning beachball and then error 1602.
Any new answers before I go to the Genius Bar ??
Thanks, Art

New Outlook sync problem after update!!!

I had the 'original' Outlook sync problem, which went away after the iTunes update to 7.3.1, but now, after the iPhone update last night, I have an entirely NEW Outlook sync problem!!
When I sync the iPhone, right when it gets to the 'syncing contacts' part (that you see in the top box/window in iTunes) I get an error message that I haven't seen before. It says "AppleMobileDeviceHelper has encountered a problem and needs to close..." and it gives me the option to send an error report. I dismiss the error box, and the sync process hangs, and iTunes becomes unresponsive.
If I open Outlook, the two Apple sync oblects are still enabled, and get no error message. If I re-open iTunes and try to sync again, it only syncs iTunes content, and never even tries to sync my contacts or calendar.
Anyone having anything similar since last night? The only thing different is the iPhone firmware update.

I just cancelled the sync by using the slider. I didn't realize I could do that. The phone seems fine. I may try it again and see what happens.

Sync problems after iTunes Match update

iTunes Match has created an ongoing sync problem for me. If Match updates automatically based on songs I've purchased from the iTunes store, then I usually have no issues with the sync function. However, if I load a CD that is not in the Match library, or if I just manually do an update to Match, it causes my 160gb iPod to take 15-20 minutes to sync. Why is this happening?

I cannot sync my music but I get the message that it is connected but it is not recognised.
As advised on the error message I have reset the Nano and re-installed itunes with the same results.
Doublechecking. Have you tried a complete uninstall of both iTunes and all the other related software components and then a reinstall? If not, try the instructions from the following document:
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8

Hot Sync problems with Windows Vista using a Tungsten E2

Need Help solving a hot sync problem. Have a Tungsten E2, about a year old. Use Windows Vista OS. Can not sync to desktop. It worked fine for awhile then stopped sync'ing. Have reinstalled Palm Software, Have downloaded Palm 6.2. Have deleted all 3rd party apps,,,and their back up files. Particulary,,,,Epocrates apps, Took over my PDA. Installations and updates gets to synchronizing Calender and 'freezes' have left it on overnight figurng lots of data,,,,no progress. I need help. I really enjoy using this equipment. I use my PDA for all my scheduling of work shifts appts etc. I would appreciate some suggestions. Thanks in advance. Mike.
Post relates to: Tungsten E2

Hi.. Welcome to the Palm forums. So if I am understanding you when you try to sync it goes to calendar and freezes and never completes the sync. That being the case the first thing you want to do is go to the conduits and turn off calendar then sync and all should be successful, except calendar will not sync. What this indicates is that you have corrupted data in your calendar, most likely on the E2. Do a google search on your computer for a utility 'dbfixit' and download it to your computer. Extract it so you have the dbfixit.prc file and double click on it to put it in the installer. Then, insuring the calendar conduit is off, sync to install it. Once installed run dbfixit. This utility is free or can be purchased for (I believe) 12.95. The free version will search for corruption and problems let you know where they are and you will have to manually fix or delete them. If you register it, when you run the utility it will find the errors and fix them as well. Once all errors are fixed, turn the calendar conduit back on and you should be able to sync.

2014 Sync problems on iPod classic / Please help!! 2014

Hello community!
I really need some help with this problem I am having... I have done some research for the past few days on my own but nothing I have found has helped.
First some specs on my device...
iPod Classic: 80 GB (I believe this is iPod with video, assumed on the fact that it supports movie syncs)
iPod software version: 1.1.2 (up to date according to iTunes)
Formatted for Windows
Syncing to Dell Inspiron with Windows 7
iTunes updated to current version (11.4)
I had much mof my music library uploaded onto my iPod for quite sometime. (close to 14,000 songs synced at 192 kbps) I often like to put my iPod on shuffle and just listen to whatever comes on, but here and there I will skip songs until something I am in the mood for comes on... I began to notice that my iPod was freezing (ON THE DISPLAY ONLY!!! Playback through speakers continued) when I would skip through songs... Once the screen dimmed however, I could once again skip to the next song. I figured this was a problem concerning corrupted files or something similar. These are the steps I took..
1.) Updated iTunes to version 11.4 and checked for further updates
2.) ATTEMPTED to check disk within Windows (was unsuccessful and heard the iPod making a lot of 'clicking' noises from within the casing)
3.) Performed an iPod restore within iTunes
4.) Performed a check disk within Windows and recovered any bad sectors (SUCCESSFUL)
5.) Selected 'Music' sync and the option for 'Entire music library'
6.) UNCHECKED 'Include music videos'
7.) Reconfigured settings as they were before and made slight changes..
     a.) Checked 'Open iTunes when this iPod is connected'
     b.) Checked 'Sync only checked songs and videos'
     c.) Checked 'Convert higher bit rate songs to '192 kbps' AAC'
     d.) Unchecked 'Manually manage music and videos'
     e.) Unchecked 'Enable disk use'
8.) Began a sync on my iPod... With well over 10,000 songs I knew this was going to be a lengthy process.. I left computer unattended..
When I returned to my computer, iTunes was unresponsive... The only way I could get iTunes to show was to minimize a Window on top of iTunes. iTunes states 'Syncing iPod... Do not disconnect' but does not show a rolling progress bar.. I cannot cancel sync, I cannot eject iPod, I cannot close iTunes...
I attempt to eject iPod device through windows, UNSUCCESSFUL (Cannot unmount generic volume while the device is in use)
I 'Ctrl+Alt+Dlt' to Task Manager and End Program 'iTunes' UNSUCCESSFUL..
I End Process 'iTunes.exe *32' and eject iPod through Windows SUCCESSFUL
When the iPod displayed 'OK to disconnect with load bar, I disconnected the device.
As soon as this bar was full iPod IMMEDIATELY rebooted completely and powered back up with only 20 songs synced. (Frustration ensues)
Confused and thinking maybe my screen saver caused an interruption during the sync, I changed screen saver and power saving options to eliminate any possible interruption, REPEATED STEPS 3-8 ABOVE, and started sync again.. Left computer unattended
Again, coming back to computer much later, iTunes was in the same unresponsive state. Closed iTunes and began looking for answers on the internet. Any and all answers I found stated I should restore iPod, update iTunes, run diagnostics tests, etc., etc...
All of which I had done EXCEPT for running a diagnostics test..
Running a diagnostics test: I ran only the tests concerned with 'Device Connectivity' and 'Device sync' tests.. Here are the very interesting results I yielded from these tests...
Device Connectivity Test:
Support services:
     'iPod support service is running.' Status: GREEN
     'iTunes Helper is running.' Status: GREEN
     'Apple Mobile Device is running.' Status: GREEN
Ports:
     'USB ports verified.' Status: GREEN
     'No FireWire (IEEE 1394) ports found.' Status: GREEN
     'iPod found.' Status GREEN
ALL TESTS PASSED
Device Sync Tests
Results:
     No iPod touch, iPhone, or iPad found. Status: RED
ONE OR MORE TESTS FAILED
I am at a loss, I realize that Apple has discontinued the iPod Classic but does that mean iTunes will no longer support these devices!?
And if ANYONE has ANY suggestions for possible steps I can take to regain syncing privileges to my iPod once again, please let me know!
Also, I have diagnostics test results saved on my desktop and available to post if required!
Thank you for any and all help!
-Chris

!UPDATE!
I made several adjustments to my sync options and made some progress and am now trying to sync in 'stages' as I like to think of them.
Here is what I did:
1.) Under 'Music' tab in 'My iPod' options I opted to sync 'Selected playlists, artists, albums, and genres'
2.) Selected a small portion of tunes I know I want on my iPod (ended up being close to 3,500 songs.
3.) Under 'Summary' tab I unchecked the 'Sync only checked songs and videos' box
4.) Unchecked 'Convert higher bit rate songs to ___ AAC'
5.) Checked 'Enable disk use'
6.) Ran a SUCCESSFUL sync!
I am now running a sync keeping the same adjustments in place and have added 6,556 songs. (SYNC IN PROGRESS)
I am wondering if trying to convert that many songs to a lower bit rate is causing sync problems and it appears as if I am at least making progress on this. HOWEVER, I really prefer to decrease the bit rate on my songs so I may fit more on my iPod... Usually most of the files I have in iTunes are at 320 kbps with a select few at 192 kbps. I would like to make everything the way it was before my first iPod restore.. 192 kbps, but this also seems to be the cause of the sync problems I am having? Anyone else have a comment on this?
Thanks again
-Chris

Frustrating audio sync problem with MJPG clips!

I make short films from our family trips, using the jpg:s and mjpg clips made with our Canon compact digital camera. This has worked fine (since PE 2). Now I often get a frustrating audio problem on SOME of the MJPG:s, SOMETIMES.
When I play the clip in PE7, after 0.5 - 1 sec the audio jumps back to start, before it continues to the end along with the video. This makes the audio out of sync with the video (lagging 0,5 – 1 seconds).
The only way to fix this is to separate the audio track from the video, cut the start of the audio (to where it jumps back to the start) and then move the audio track to make it in sync. Besides being a tedious way to do on all clips, the audio track is not possible to extend “in the other end”, so I have to cut the video at the end as well…
However, this is not happing on all MJPG clips but only on some.
Also, the clip looks fine in other programs, e.g. wmp or windows movie maker.
I have tried other MJPG decoders but that does not make any difference (so it’s obviously no problem with the video). The audio is PCM Audio 44100Hz, 706 kb/s mono.
Now, when I tried repairing the PE7 installation, updating DirectX, removing all caches in the project directory, rebooting, it worked! The clip I was testing was in sync!
But, the next day I noticed the sync problem again on a lot of other clips… I then thought I should try to force PE to reanalyze the video again, so I remove the cache-directories (did not help) and moved the project file to another directory (this did not help, but on the other hand, I didn’t see PE7 analyzing the video again, so maybe there is a cache somewhere else??)
I noticed (looking at properties on the clip in the preview window in PE7), that the original audio is 44100Hz mono, but PE7 converts it to 48000Hz mono. Don’t know if there is some problem there, but it should not be any difference on different clips from the same source… (and the “jump back” in audio is 0,5-1 seconds regardless of clip length, and not the 9% that the difference in frequency would suggest + the audio plays in “normal speed”).
I’ve run out of ideas!!
Please, does anybody have any constructive ideas or tips on what to try? Are there more caches to clear? Are there conflicts with another program, like wmp?
(I use PE 7.0 on a 4Gb, quadcore system running Windows Vista Home Premium 64 bit.)
// G

Thanks, I suppose I can start batch-converting my mjpg movies before importing them inte PE7, if that would make this problem disappear. I'll try that (I have FormatFactory installed, but VirtualDub seems like a nice tool if that is better), although that would make the process a bit more long-winded...
Regarding GSPOT info on a file that works and one doesn't, there are typically no difference between them (except length and content, of course). In fact, as I mentioned above, the same movie did not work until I did some reinstalling, clearing caches etc. Then the same movie suddenly worked OK again.
I attach the GSPOT info on that file.
(I never had this problem on my older XP system that run PE2...).
I will try converting to see if the problem disappears.
Thanks!
// G

AV sync problems when rendering Quicktime in PE 8

I have a simple problem when rendering to Quicktime format fromPremere Elements 8: The AV sync goes out of whack.
I have tried rendering:
(a). To MPEG - output is fine.
(b). To WMV - output is fine.
(c). MOV - av sync errors
I am assembling about five clips. The first clip plays fine. The AV sync problems starts at the second clip - the audio is a good 3 seconds or so ahead of the video.
Everything is fine in the editing window.
I am running in Windows 7. To make sure it is not the player, I have played the quicktime output in Windows Media and itunes and the same problem is in both.
Has anyone seen this issue?
Thanks.

Hi Steve,
Sorry for the confusion. It a sensible suggestion to identify the input formats and output formats and I would most appreciate your inputs to this issue because I admit that I am really struggling here to get a workflow going.
Input formats:
1. MJPEG 1280x720P at 24 frames per second (from a Panasonic Lumix Camera)
2. WMV 1280x720P at 24 frames per second from output of other programs (which only support wmv output at High def output)
3. MPEG2 1280x720P at 24 frames per second (and sometimes 25 frames per second) from other sources
Target output formats are:
1. Blu-Ray
2. MP4 container format @ 1280x720P for playing on my Apple TV
3. DVD (ordinary plain PAL DVD at 720x576P at 25 frames per second)
My goal is have Pre Elements 8 Project settings in High Def and then to simply target all three outputs from one project so that I do not have to redo all of the projects with different project settings.
Workflow is in two stages:
Step 1 is to create one project for each Chapter and save to disk: The inputs are from all three input formats that I identified above (High Def - MJPEG, WMV, and MPEG2). I would like to edit, mix the audio, and then save each chapter to disk. The format in which I save this is preferably some kind of high def format that can be edited easily at a later time.
Step 2 is to create the Project that is used to assemble each chapter for final output: This is the project where I put in Chapter marks, create menus, etc. The target outputs from this chapter are Blu Ray (high def), AppleTV (high def), and PAL DVD (Standard def).
In all cases, I set up my Project Settings as HDV-AVI for internal rendering because all inputs are high def and most target outputs are high def.
Issues that I am dealing with:
1. I cannot figure out the best export format to go from Step 1 to Step 2. HDV-AVI doesn't seem to be available as an export format. Basically, I am looking for an export format that puts the least strain on resources when they are read in for Step 2 and retains the highest quality.
2. Most of my inputs are 24 frames per second but the internal rendering for Pre Elements 8 seems to be 25 frames per second. Frame rate conversion can be quite tricky and can put significant strain on resources, but it is not clear if this is straining Pre Elements 8 or not. It does seem to be. I am happy to convert my files into a format that puts the least strain on Pre Elements 8 internal rendering and yet produces the best output.
Note: If you ask - why do I do this in two steps? It is because I am always putting a strain on system resources when operating in high def. Unless I am careful, I get a message that Pre Element is "low on resources" followed by a crash shortly thereafter. I have Win7 32 bit, 4 GB RAM, no other programs running, all drivers updated with the most recent version (yes - even the NVIDIA driver) so there really isn't anything else that I can do in this area.
So I am looking for suggestions in the following areas:
1. An alternative workflow that produces the three high def outputs with the three high def inputs defined above that doesn't cause Pre Elements to continually go low on resources and crash.
OR
2. A recommendation for a high def format that puts minimal strain on Pre Element resources?
Thanks!

.mov sync problems

I'm having sync problems with an 11 min Quicktime video
piece. The project is just a basic interface with control buttons
(Play, Rew, ffd, etc...) for the video. I've encoded it in several
ways and still get the same problem. Audio and video are slightly
out of sync. I normally use pieces that are 3 to 5 minutes long and
don't have these issues . Could it be that Director has a bug for
longer length pieces? Please help.

Alternately, you can try using the MpegAdvance xtra instead
of
Quicktime. It is not free, but it works very well, and most
of the
commands are the same as QT, so there isn't much of a
learning curve. I
have had very good luck using it in the past.
-Mike
Sean Wilson wrote:
> Can you try updating to the latest version of QT (and if
it works
> include the installer with your distribution)?
> Also, ensure you have the latest Director update
(10.1.1) which includes
> the latest version of the QuickTime Asset xtra

X6 and ovi suite sync problem - usb connection

i recently bought an x6 and set up ovi suite etc which all worked fine! yesterday i updated maps and the x6 operating system using ovi which again seemed to work fine. Now however when i connect phone to my pc the pc comes up problem with hardware installation and ovi suite only occassionally recognises phone - even when it does it will not sync music! help please - wish i hadn't updated anything as it all worked fine before !!!!

I have a similarly frustrating sync problem with my X6. It's my second phone too.
I've had Ovi Suite installed on my computer for about 9 months. I had difficulty getting it to sync with my X6 phone at first but after some troubleshooting I got it working reasonably well.
However over the last few months it doesn't initiate the syncing process after I connect my device. I can open Ovi Suite and click the sync buttons but it doesn't do anything.It doesn't freeze or crash either which is strange considering it is not processing the request.
I've tried everything including reinstalling the software and resetting my phone. This worked once and since went back to it's old tricks.
The only thing that works is removing the X6 device in OVI suite, rebooting the PC and adding the device again. This is real pain in the backside as you can imagine doing this each time I want to sync it.
In contrast the previous version - PC Suite - worked well with my old Nokia phone.
Nokia support have provided some guidance after pushing for a reply but you dont get expert or timely help from them.
Come on, we cant be just a few people having these issues? I reckon lots of x6 owners aren't getting full value from these devices.
It's at the stage where I'd not recommend a Nokia x6 or other Nokia phone to anyone wanting the PC connectivity which is one of the major benefits of a phone these days.
Go on Nokia give us some love!
One frustrated owner counting down the days to my upgrade option.

Airpot update. sync problems. etc.

Similar Messages

Maybe you are looking for