Airtunes Audio from One Speaker Only

I've been running my Airtunes device for about a month now. However, I've just noticed that the sound is only coming from one speaker. I have done all the normal things such as changed the speakers, and changed the audio cable, but the problem persists. Apart from that, the devices exhibits no other problems.
Before I send it back on warranty, anyone have any ideas on what I might be able to check. TIA.

Have the same problem mate...really annoying.... i went and bought a better quality cable but to no avail!! Bringing it to local mac service place tomorrow to get it checked out. Looks like the stereo input port is wrecked!!

Similar Messages

  • In-ear headphones playing audio from one side only

    My apple in-ear headphones only play audio from one side.  I've tried replacing the cap and mesh; and also tested the headphones on different devices and still get the same problem.  Any advice?

    Probably time to have them replaced.
    B-rock

  • No audio from one speaker using the front jack

    I have an hpe-230f. Today I tried to use my headphones and I found out that I only got sound with one speaker.  I used a few other sets of headphones and got the same result. The sound jack on the rear is fine so I suspect that the front port dongle/cable is faulty. 
    I contacted HP support to try to get them to send me a replacement front dongle but they want me to send it in but I can't because I need the computer for schoolwork and if they end up reformatting my hard drive while it's being serviced I''ll be stuck on the phone with Microsoft for quite some time trying to get them to reacivate my Office 2007 key .
    Any ideas?

    Hi,
    Try the following.
    Shut down the notebook, unplug the AC Adapter and then remove the battery.  Hold  down the Power button for 30 seconds.  Re-insert the battery and plug in the AC Adapter.
    Tap away at the esc key as you start the notebook to launch the Start-up Menu and then select f10 to enter the bios menu.  Press f5 to load the defaults ( this is sometimes f9, but the menu at the bottom will show the correct key ), use the arrow keys to select 'Yes' and hit enter.  Press f10 to save the setting and again use the arrow keys to select 'Yes' and hit enter.

  • BAD audio from one speaker (the other is normal)

    I JUST got my iMac today in the mail, and all was going swell, I was pleased... that is till i started to play some music, it sounded a little weird, I isolated the problem to the right side.
    I played a movie and the speech is what's noticeably distorted.
    I heard apple has a return policy, what is it?

    Sorry to hear of your problem. Contact wherever you bought it from and ask them. No one here can help you as we are just users and the decision has to come from wherever you purchased it. I would imagine that they would replace a bad, brand new out of the box unit but only the seller can do that for you.
    Good Luck!!

  • Broken key on keyboard and staticy audio from one speaker. Advice?

    Hey everyone, I'm new around here, name is Mike...
    I bought a T61p last Sept. and have loved every minute of it.
    However, I have two problems:
    a)  I was typing the other day and one of the keys (the ctrl key on the right hand side) popped off, and I can't seem to pop it back on.  I think one of the little connectors might be broken?  Normally I don't even use this key, so it's not the end of the world, but it looks kind of trashy, and I'm worried about excess dust getting into my computer now that there is another opening. 
    b)  When playing music above level "40", there is lots of static on the left speaker.  It has been this way since day one, but since I normally use external speakers or headphones, it's never been too big of a problem, but since I might be sending it out to get my keyboard fixed, I figured I should have the issue addressed.
    According to the warranty, I have until Sept 09 for it to run out...
    So, my question is what should I do to get my T61p back into perfect condition?  What steps should I take?
    Thanks!!!
    Message Edited by CarpeD1em500 on 05-05-2008 01:12 PM
    Solved!
    Go to Solution.

    Well, by "limitation" I mean that a tiny 0.5" speaker doesn't have much power handling capacity and unit to unit variation will likely result in the breakup of one before the other.  You aren't going to get "loud" and you aren't going to get "bass" (if you turn up the bass in Media Player that will definitely distort the speakers).
    Keith
    Formerly 600E 2645, T30 2366, X31 2673, T40 2373, T41 2379, T42 2373, T42 2379, T60 1952, T61p 8889, T61p 8891
    Currently T420 4177-CTO, T430 2347-A54, T430 2349-L64, T430 2347-UN9, T430 2342-CTR, Ideapad K1, H520S 2561-1LU

  • Sound out of one speaker only

    Sound has started to come out of one speaker only. i've checked cords to amplifier etc etc and that is not the issue,. Anyone else had this problem?

    Hello adyomo. Welcome to the Apple Discussions!
    Please try connecting a pair of stereo headphones to the audio port of your AirPort Express Base Station (AX). If you now get sound from both channels, the problem may still be either with the cables or the amplifier. If; however, you are still only getting sound from one channel, either the AX's audio port or its audio circuitry may have failed.

  • Multi-Camera Source Sequence Audio from 1 Speaker instead of both??? HELP PLEASE!!!

    So I have been at this for awhile now. Am I missing something?
    I simply take my 2 .MOV's and 1 .WAV and I create a mulit-camera source sequence. Except when I play it from my time line and it appears in my program pane it only plays the .WAV from one speaker...
    If I break it apart and load the .wav from the timeline into the source pane using keyboard shortcut "F" then it plays through both speakers..?
    Attached is a screen shot of the broken down Mulit-Camera Source Sequence by clip.
    Please help me, thank you!
    Multi-Cam sequence ONLY PLAYS AUDIO FROM LEFT CHANNEL, Adobe Premiere Pro CC.Multicam Editing in Premiere CC IssuePremier Pro Multicam Not Working.creating multi-camera source sequence w/ externally recorded audio

    I just tried that, although it still plays out one speaker when I play it in the timeline, either out or in the nest.  It appears that the timeline has an audio setting that is off perhaps? Or a bug? I have attached many images to check out... Thank you advance!

  • I want to use the audio from one of my clips and the video of another can I do this?

    I have two different video clips that I took from my still camera. I want to use the audio from one of the clips and the video from the other at the same time in imovie can I do this and if yes how

    Yes.
    First go to iMovie/Preferences and make sure that the Advanced Tools are enabled.
    Now, drag the clip with the Video into the project.
    Drag the clip with the Audio and drop it on the first clip at the frame where you want it to begin. A popup menu should appear. Choose Audio Only. You may then want to open Inspector for the video clip (by clicking the little gear icon at the top left of the clip) and going to the audio tab. Here you can turn down the volume of the video clip, so that all you hear is the audio clip.
    Another way. Put the video clip that has the Audio you want in first. Then drag the clip with the video you want and drop it on the clip that has the audio you want. A popup menu will appear. Choose CUTAWAY.

  • Sound on one speaker only

    Last night, while using iChat with another Mac user I was only getting sound from one speaker (right). Both speakers work with iTunes so it's not my hardware (I don't think it is anyway). Could this just be poor bandwidth?
    Thanks.
    MacBook Pro   Mac OS X (10.4.6)  

    Hi MacBoy70,
    This is the iChat software preventing you getting feedback as the MacBook Pro internal Mic is in the left hand speaker grill.
    4:30 PM Thursday; May 18, 2006

  • How can i leave audio from one clip playing, while showing another one in i

    i am editing a movie, using iMovie 08, and want to use sound for a clip in the video for the end credits. how can i do this?
    just to be clear, i am not trying to add audio. i am trying to leave the audio from ONE CLIP playing, while viewing a new frame. thanks.

    This is simple in iMovie 11 (drag and drop), but in iMovie 08, you can still do it.
    [See this blog post for details|http://imovie08.blogspot.com/2007/08/how-to-extract-audio-from-clip.htm l]

  • When I have two clips, one above the other, I would like to hear the audio from one at a time. How do I suppress temporarily one of that, in a easier way? Thank you.

    When I have two clips, one above the other, I would like to hear the audio from one at a time. How do I suppress temporarily one of that, in a easier way? Thank you.

    I would think you would drop down the audio level lines in the "Stereo" tab (FCP 6.0.6 view to me) in the clip's video window.
    But then again, in my old version, I can't play two clips at once.  But I figure if the newer FCP allow you to do that, then that's what I would do.

  • Sound works from one headphone only

    Dear all,
    I can hear sound from one headphone only.
    I can confirm I have tried with three different headsets including the one provided by Sony.
    I can also confirm the problem happens with all applications (Spotify, Walkman, SoundCloud) including the provided sounds and ringtones. 
    Also, the phone has not come in contact with water yet and it hasn't been dropped either (it's two weeks old).
    Last time it worked, was last night when I connected it to my home stereo using a normal stereo minijack. It has stopped working since then.
    I have restarted it a number of times and the problem persists.
    Can you please advise?
    Many thanks in advance
    Solved!
    Go to Solution.

    Dude i have a big piece of fluff inside the hole, and it was the reason for the malfuction for me. Im happy aggain couse i was affraid a little. 
    Spoiler (Highlight to read)
    not a little... almost the baddest day of the year!! 
    not a little... almost the baddest day of the year!! 

  • Help lost audio on one session only and other faults occurred

    Hi  for some reason I have lost the audio on one session only .in multitrackAll other sessions play ok /The tracks in this session  play in edit and   also show as playing on the meter bar in multitrack but no actual audio heard.  Even more annoying is that now if I click anywhere on the task bar  whilst playing a session it stops. I am not aware of making any changes in Audition but vaguely recall possibly hitting another Key whilst tapping the space bar  , Any advice greatly appreciated thanks.

    Eedcam wrote:
    The tracks in this session  play in edit and   also show as playing on the meter bar in multitrack but no actual audio heard.  Even more annoying is that now if I click anywhere on the task bar  whilst playing a session it stops. I am not aware of making any changes in Audition but vaguely recall possibly hitting another Key whilst tapping the space bar  , Any advice greatly appreciated thanks.
    If the transport is running, and you can't hear anything, then at least your audio device is still connected. If it wasn't connected, you wouldn't even get the transport to start. On that basis, I'd suggest having a careful look at the mixer, and seeing if you've accidentally done something like muting the Master channel, or accidentally knocking the fader back to zero. Under the circumstances you describe, this is pretty much where your problem's got to be, I think, especially if it's only on one session.

  • Suggestions for blending audio from one clip to next?

    I'm learning editing and PP and am practicing by editing different clips from a movie to make my own trailer. The problem I'm having is that going from one clip to another has obvious and abrupt changes. I could add audio transitions to each clip, though for a 2.5 minute trailer I'm not sure if fading audio up and down constantly is the best choice? What is the best way to blend the audio from one clip to the next?
    Thanks.

    You can create a crossfade (essentially an
    audio dissolve) from one audio clip to another.
    With the audio track(s) targeted, park the Playhead at the
    audio cut and hit Ctrl+Shift+D (or drag from the effect panel):
    You need to be sure you have sufficient 'handles'
    on both clips to accommodate the crossfade.
    Creating an audio crossfade
    http://tv.adobe.com/watch/learn-premiere-pro-cs6/creating-an-audio-crossfade/

  • I created in iMovie, and extracted audio from one of the clips to use in the title sequence.  All is well, export to iDVD and it plays OK, but when I burn the DVD the audio for the titles does not play. Any suggestions?

    I created in iMovie, and extracted audio from one of the clips to use in the title sequence.  All is well, export to iDVD and it plays OK, but when I burn the DVD the audio for the titles does not play. Any suggestions?

    I am on a MacBook Pro with OS 10.6.7 running iMovie '11 and iDVD 7.1.1.  Thanks for any input.

Maybe you are looking for