Airtunes issue with Sonicwall
I just set up a Sonicwall TZ 150 wireless router and am having issues extending the wireless network with my AE. The Sonicwall shows the AE as being connected but I am unable to see the AE in the Admin Utility or in iTunes. Interestingly, I can click Other in the Admin Utility, enter the Sonicwall assigned IP address and connect to the AE.
Does anybody know why I can't see the AE from the Admin Utility but can connect to it by manually specifying its IP address? I'm assuming this is the same issue that's preventing iTunes from seeing the AE.
Thanks in advanced for the help.
Macbook Pro Mac OS X (10.4.8)
Hi Chocky,
As I know, when you are connecting to a VPN, client require IP information from VPN server instead of DHCP server.
When the RRAS server uses this type of proactive caching of DHCP address leases for remote access clients, it only records the following information for each lease response it obtains from the DHCP server:
The IP address of the DHCP server.
The client leased IP address (for later distribution to the Routing and Remote Access client).
The time at which the lease was obtained.
The time at which the lease expires.
The duration of the lease.
For more information about RRAS and DHCP
https://technet.microsoft.com/en-us/library/dd458962%28v=ws.10%29.aspx?f=255&MSPPError=-2147217396
So we suggest your check this issue with your VPN provider or run command you mentioned as a workaround.
Regards
D. Wu
Similar Messages
-
Cisco ASA 5510 Site to Site VPN with Sonicwall
I am trying to setup a VPN tunnel between a Cisco ASA 5510 (Version 8.2(2)) and Sonicwall TZ200. I got tunnel up and going and I am able to ping the Cisco ASA internal IP from the Sonicwall LAN but nothing else works. When I try to ping a host behind the Cisco ASA from the Sonicwall LAN I get the following message "Asymmetric NAT rules matched for forward and reverse flows; Connection for tcp src outside:10.20.10.x/xxxx dst inside:10.20.2.x/xxxx denied due to NAT reverse path failures" on the ASA
Googling the above error shows issues with version 8.3 and later which looked like the nat commands were changed but the ASA I am working on is still on 8.2 and the other common issue is not adding a NAT exemption. I have double-triple checked that I did add a NAT exception rule from the hosts on the cisco network to the hosts on the Sonicwall network. Seems like I have hit a road block so any help would be appreciated. Thanks
Here are some excertps from the config file (10.20.2.0 behind the cisco and 10.20.10.0 behind the sonicwall)
nat (inside) 0 access-list nonat
access-list nonat extended permit ip 10.20.2.0 255.255.255.0 10.20.10.0 255.255.255.0
access-list outside_1_cryptomap extended permit ip 10.20.2.0 255.255.255.0 10.20.10.0 255.255.255.0
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set peer x.x.x.x
crypto map outside_map 1 set transform-set ESP-3DES-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 28800
group-policy SiteToSitePolicy internal
group-policy SiteToSitePolicy attributes
vpn-idle-timeout none
vpn-tunnel-protocol IPSec
split-tunnel-network-list none
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group x.x.x.x general-attributes
default-group-policy SiteToSitePolicy
tunnel-group x.x.x.x ipsec-attributes
pre-shared-key *****
Added few excerpts from config fileYes inspect icmp is enabled in global_policy
The ping requests time out (The only ping that works is when I ping from the remote side to the ASA internal IP address, no other pings from either side work)
#show crypto isakmp sa
1 IKE Peer: x.x.x.x
Type : L2L Role : responder
Rekey : no State : MM_ACTIVE
#show crypto ipsec sa
interface: outside
Crypto map tag: outside_map, seq num: 1, local addr: x.x.x.x
access-list outside_2_cryptomap extended permit ip 10.20.2.0 255.255.255.0 10.20.10.0 255.255.255.0
local ident (addr/mask/prot/port): (10.20.2.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (10.20.10.0/255.255.255.0/0/0)
current_peer: y.y.y.y
#pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
#pkts decaps: 39543, #pkts decrypt: 39543, #pkts verify: 39543
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: x.x.x.x, remote crypto endpt.: y.y.y.y
path mtu 1500, ipsec overhead 58, media mtu 1500
current outbound spi: 0ED0F897
current inbound spi : 596CCE6F
inbound esp sas:
spi: 0x596CCE6F (1500302959)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 50327552, crypto-map: outside_map
sa timing: remaining key lifetime (sec): 7440
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0xFFFFFFFF 0xFFFFFFFF
outbound esp sas:
spi: 0x0ED0F897 (248576151)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 50327552, crypto-map: outside_map
sa timing: remaining key lifetime (sec): 7440
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001 -
Back when life was simple, under Windows XP, i simply fired up my SonicWALL client, connected to the host, and then connected via RDC and all was good.
Now I have Windows 8.1 and SonicWALL's v4.9.0.1202 64-bit client. I can connect with the client - although it seems to drop the connection quite a bit - but when it is up, I can ping the host. But when I try to RDC, I get the completely unhelpful
error mentioned above.
My version of 8.1 is up-to-date - the VPN client came right from DELL's website. What am I doing wrong?
Just in case you want to know, yes - I can RDC to non VPN and PPTP VPN sites no problem - and on the same LAN, my XP box can RDC with SonicWALL with no issues.
Please, somebody - i need to get back to Planet 10!Did you ever find a solution to this problem. I am having the exact same problem
-
I have had several security issues with Windows 8.1 Pro.
I am curious if the following apps should be loaded by default:
CheckPoint.VPN
JuniperNetworks.JunosPulseVpn
SonicWALL.MobileConnect
F.vpn.client
These programs are installed on a fresh install of Windows 8.1 Pro but I do not think they should be. They are present prior to the install of any 3rd party programs or apps.
ThanksI found them in my firewall list on my Windows 8.1 Pro installation and posted a question on a forum as well, though I don't think it was here. I don't believe anyone ever answered.
It looks as though these are parts of the bundled virtual private networking clients.
Note, for example, the "distributed by Microsoft as part of Windows 8.1" wording on this page:
http://www.sonicwall.com/app/projects/file_downloader/document_lib.php?t=PG&id=605
-Noel
Detailed how-to in my eBooks:
Configure The Windows 7 "To Work" Options
Configure The Windows 8 "To Work" Options -
ITunes 9, Apple TV, and AirTunes issues
It seems that iTunes 9 on my iMac has two issues, possibly related, both of which are very irksome. Both issues appear after the computer wakes from sleep, leading me to think they are symptoms of the same problem.
Issue #1 is that the AppleTV keeps vanishing from the list of devices. iTunes knows about the AppleTV, the AppleTV is on the network and can stream from iTunes, but the device is missing and hence sync won't work. I've checked the firewall log and the AppleTV is being accepted for incoming connections, so it's not a firewall issue. I've reset the AppleTV, reset the connection between iTunes and the AppleTV, resynced all my content and the problem persists.
I've found two ways to fix this issue: restart iTunes, or go to Preferences : Apple TV, uncheck "Look for Apple TV", close Preferences, open Preferences and recheck the same selection. After a 2-3 second delay, the AppleTV appears in iTunes.
Issue #2 is that the remote speakers connected via an Airport Express disappear. This seems to happen at the same time as the AppleTV disappearing, as the drop-down box for selecting the remote speakers vanishes. Normally it lists the computer, the Apple TV, and the stereo but then the box goes away.
Similarly for issue #1, I can get the drop-down back by going to Preferences : Devices and unselect "look for remote speakers", close and reopen Preferences and reselect the same checkbox. Interestingly, doing this does NOT bring the AppleTV back as a device, but the Apple TV is listed along with the remote speakers.
I think the two issues are related, as they both involve the network. My computer is linked via Ethernet to the DSL router with 802.11 then going to the two devices. It seems to me that iTunes is not reestablishing the connection after waking from sleep. But it's not consistent; I can put the computer to sleep and wake it up, and the connection is there. Other times the connection is gone.
The only thing I can't rule out is a problem wirelessly connecting to the devices, but the AppleTV has always reported 5 bars of signal, and the fact that it still streams from iTunes, yet iTunes doesn't see it, makes me think the problem is in iTunes.
Hopefully this will be helpful to someone else with these problems.After suffering with the Apple TV for four months, and scouring the internet for fixes, tricks, and workarounds before posting, I have to wonder how many thousands of people there are silently slamming their heads on the sofa while they wait for apple TV to unfreeze, catch up to their attempted remote prompts, or simply just restart as if ATV even gave up on itself. (issues are in Bold)
I have to opt with the streaming feature to bring my movies, music, and photo's to a big screen and home theater sound system due to a 2TB (mostly full) Western digital external HD plugged into the 802.11n airport extreme.
A possible reason for *the 2 second stoppages in play of movies and music are that the airport has to link the music/movies to my computer(itunes), which must travel back to the airport to go to the apple TV.*
I'm also using the iphone for remote use, being that the infamous IR issues with the standard remote are so notorious, I wouldn't be surprised if Best Buy started selling the ATV with white paper already taped to the sensor.
*While using the main menu, 1 out of 4 times in a five minute period of navigating the ATV, the product is unresponsive to commands from either type of remote, and I am left to:*
*1. wait until it unfreezes after about 4 min (60% of the time) when all prompts are suddenly recognized by ATV, all at the same time, to which often it goes back into another multi minute freeze before use is temporarily made available again.*
*2. hold the menu button down on the IR remote so ATV restarts after i've waited over 5 min to see if the freeze will work itself out(15% of the time) or*
*3. try to wait out the issue until the ATV restarts itself with no prompted action (10% of the time) to which I am asked to pick a language again and given the option to restart, run diagnostics or restore factory settings.*
*---The last 15% of the time ATV stays frozen and unresponsive to any remote for, in my estimation ever (I literally waited almost two months, pressing buttons many times a day to try an wake the ATV got nothing but a screensaver before i gave in), until you're forced to pull the plug because the holding-menu-button restart option isn't even working **
I've tried restoring factory settings, changing IR remote batteries, unpairing and repairing, unsyncing and resyncing both itunes libraries, remotes and airport extreme connections, jogging the itunes preferences, putting paper in front of the IR sensor, restarting both itunes and unplugging the ATV, and I even went back to exchange the apple tv for another apple tv to see if it was just an issue with the hardware...nothing has eased these ailments.
The airport and all wireless devices in-play are no further than 15 feet from each other, including the airport, which is just on the other side of a very thin wall w/i 10 feet of the ATV.
*If, in the menu freeze, (which, again happens about 25% of the time i attempt to navigate the ATV menu) you give up on the iphone remote, u see the ATV is receiving the signals from the IR remote, but nothing moves most of the time (mentioned above) and the best you might get after waiting and trouble shooting long enough is the screensaver stopping for a split second, when u press a button on the IR remote, before continuing to ken burns until you want to use the ATV to play frisbee with interstate 20 traffic.*
I'm not sure if Apple over-engineered this device to the point where it's tripping over itself to perform the most basic functions, but I bought this device so I could watch my movies and listen to my music wirelessly, and at this point, the DVI wire and headphone jack splitter are a much more reliable (yet burdensome) option than the ATV.
If I had to guess, it seems most problems stem from users who stream from an external hard drive, whether it be plugged into the host computer, or broadcast wirelessly (this is not taking into consideration the IR remote issue). This might be an unpopular suggestion to Apple, and i'm sure you have some reasoning for not making this an option, either for monetary or twisted legal obligations but the internet complaint factory might be a little less whiny if you just simply make an option to have the ATV be a screen emulator, with AirTunes, and cut all the other youtube, direct internet to ATV garbage that 65% of the people using this product didn't buy it for.
I have been nothing but awestricken with Apple products since I was a child, and thought there were no ends to the company's ability to make products that work with each other easily, seamlessly, and without the need of a computer engineer to set it up for you. Unfortunately though, it seems, for the time being, we might have met the limits. -
Issues with Windows 8 and UML295...?
This is my first experience using any sort of USB dongle for wireless internet. I'm using a Pantech UML295 with a Lenovo Yoga Convertible Laptop with Windows 8 Professional. Upon inserting the USB dongle into the laptop, it takes a few moments but does eventually connect to the internet. My big thing is that I need to be able to use my Sonicwall Global VPN Client to connect to my corporate network. However, when I launch the application (with the UML295 plugged in) the program never opens. I've also noticed that many other applications either don't open or run extremely slow. Interestingly enough, as soon as I remove the UML295, all "hung" programs magically refresh and open up as normal. The VPN client pops open and attempts to connect (assuming my WiFi signal picks up where the UML295 left off.)
I attempted the same scenario on a Windows 7 laptop and all worked just fine. It looks to me like it's a Windows 8 compatibility issue with the UML295. Has anyone else been experiencing this? With the UML295 being so new, I have been unsuccessful in finding much information on this topic. Hopefully others will start to have some of the same problems and will begin posting their findings. Working in the IT business, I find this issue to be very frustrating, as I am usually the one that's able to solve these types of problems!I think I found a solution to my own problem, in case anyone else runs into this.
I was able to get it working by launching the Sonicwall Global VPN client BEFORE I plugged in the UML295. It's a very slow connection process but it still connects nonetheless - you just have to be patient with it. After the SW VPN client is enabled, the UML295 will find an IP address and then proceed to authenticate itself on the corporate VPN.
I hope someone can find this information useful. -
Issues with Windows firewall and Airport Extreme
Hi all,
I'm having some issues with my Airport Extreme and Windows Vista firewall. I've got the most current versions of all the airport express software and firmware. My iTunes can see the remote speakers, and I can access the airport extreme using the apple-supplied admin software, so I know that they are working and on the network.
However, when I try to stream music through iTunes, the speakers won't connect. (yes, I have the "stream-music" option checked) However, when I disable windows firewall, they work fine. Therefore, the issue seems to be with a specific port that is not open through windows firewall. When I checked the exceptions for windows firewall, all the associated apple software is listed as exceptions. I think that there is one more port open that I do not have.
Any thoughts?
thanks.AirPlay/AirTunes is based on the ROAP protocol. I would suggest trying the following ports:
Add TCP 443 for SSL
Add TCP/UDP 554 for RTSP
Add TCP 3689 for DAAP
Add TCP 5000, 6000, and 6001 for ROAP
Add TCP 5297 for Bonjour
Add TCP/UDP 5298 for Bonjour
Add UDP 5353 for Airport discovery
Add TCP/UDP 7070 for RTSP
Add TCP 8000-8999 for iTunes radio streams
Add TCP 42000-42999 for iTunes radio streams -
Ethernet/wireless connectivity issues with Airport Express
I am having problems with my PC seeing my newly aquired AE and was hoping someone can help, none of the topics already discussed seem to be exaclty the same as my issue.
Scenario:
* iTunes on the PC does not detect the AE so I cannot play my iTunes setup through my stereo.
* The PC can ping the AE.
* The PC can configure the AE if I open the AirPort utility and go to File, Configure Other and enter teh units details.
* Both laptops can connect to the AE via iTunes and the AE Utility also picks up the device.
Equipment
* I have an Open Networks 625W 4 port ADSL router with wireless included in the unit.
* My PC is connected to my LAN via ethernet and is running Windows Vista fully service packed.
* I have two laptops both connected via wireless on my LAN and all devices (ethernet and wireless) can see each other.
* I have an AE with latest firmware and the latest version of the Airport Utility running.
* The bonjour service is running on the PC.
* I have tried turning the PC's F/W off with no change.
* I have tried connecting one of the laptops to my network via ethernet and had the same issues as the PC.
Configuration:
I have tried many different methods of configuration but the one that has me working this far is-
* Joined to a wireless network.
* Using DHCP (and getting IP addresses fine off the third party router)
* Connection sharing is off by default so its working in bridged mode.
Its almost as if the router is not allowing those packets related to Airtunes to pass through from/to the wireless router(and I have tried so many different settigns there). I believe Bonjour is required and Im not sure if any routers have issues with bonjour but I believe its encapsulated within IP packets (not sure on that though). Or Maybe some routers don't work in this scenario and I need to update to a Belkin Wireless G or N or other. Or maybe the software will only accept direct wireless connections if its configured for wireless - I have no idea and am losing hair fast.
Please, any help would be appreciated.I finally cracked it!
I have enabled dynamic routing with RIP v2 (v1 works too), enabled multicast with IGMP proxy and used a bridge filter allowing all traffic between the LAN and the wireless networks. All three settings are required with my router. If I drop any of them AE from LAN to wireless will not work. -
Issues with Creative Cloud for teams deployment workflow
The Adobe Creative Cloud for teams IT Deployment Guide lists out steps for IT admins to deploy the CS6 applications and then have their end-users license the trial software with their Adobe IDs once they have been invited to the team. There are two major issues with this document.
First, the media that is on the FTP is not for North American English. We are working to get that posted on the FTP site ASAP. In the meantime, you can find the CS6 MC media from: http://www.adobe.com/downloads/
[Note: Getting media from that page requires the use of the Adobe Download Assistant which is very consumer focused. Sorry about that.]
Second, in order to have the ability to login properly with a Creative Cloud for Teams account the system needs to have the latest copy of Adobe Application Manager installed. If you do not do this step the end user will be prompted for a serial number.
Unfortunately the Adobe Application Manager can’t be packaged with AAMEE nor is it a native installer. I know, I know! Here are the links to the Adobe Application Manager installers:
Windows: http://www.adobe.com/support/downloads/detail.jsp?ftpID=4773
Mac: http://www.adobe.com/support/downloads/detail.jsp?ftpID=4774
It can be installed from command line by:
Win: <Path to Setup.exe>Set-up.exe –mode=silent –action=install
Mac: <path to ASU> /ASU/Install.app/Contents/MacOS/Install –mode=silent –action=install
Jody Rodgers | Sr. Product Manager | Creative Cloud for Enterprise | Adobe SystemsHi Boncker,
I see that you have an active Subscription under your account . Please launch any of the installed product and when you get the trial prompt , please click on License this software and then Enter the Adobe Id & Password for the account that you have accepted the invite .
Please do let us know if that worked for you or not .
Cheers,
Kartikay Sharma -
Issue with magsafe/charging (blinks green, amber, off)
Having a quirky issue with my mid-2009 Macbook Pro.
A month or so ago, I began having an issue with my macbook charging. When the computer is up and running and I plug in the magsafe it will say "Calculating..." and then say "Not Charging" and then switch to battery use. It constantly does this as long as the magsafe is connected. The lights on the magsafe will constantly cycle from green to amber to no light.
At first, it would do it a few times then it would start charging. Now it constantly does this without ever stopping. I was editing video the other day for a while and it never stopped the cycle.
Thinking it was the battery, I took it into the Apple Store last week and got a new battery because it had been saying "Service battery" for a while and the battery would only last about 20 minutes on a charge. So I just thought the battery finally refused to charge.
But the problem still exists.
The magsafe is new (only 3 months old) and here's the quirky thing: the computer will charge if it's asleep (lid closed) or shut down completely. No blinking lights at all. It will charge as long as it's asleep or shut down. So I don't think it's the charger. But as soon as you hit the power button to starting booting up, it will blink.
I have reset the SMC a couple times actually, but no change.
Is there something software/firmware related that I haven't tried? Any insight or suggestions would be greatly appreciated before I take it back to the Apple Store (which is about an hour away).
Thanks!Try resetting the system management controller
http://support.apple.com/kb/HT3964?viewlocale=en_US
If that did nothing for you, try resetting the NVRAM
https://support.apple.com/kb/HT1379 -
Issue With Page Break When Sorting is also applied on group
Hi
I am facing an issue with Page break only when I have sorting applied on the grouping that I have in the template.
The following is the sample XML
<ROWSET>
<ROW>
<GRE>org1</GRE>
<ORGANIZATION>Accounts</ORGANIZATION>
<FULL_NAME>test1,</FULL_NAME>
<ELEMENT_NAME>TEST BONUS</ELEMENT_NAME>
<CLASSIFICATION>Supplemental Earnings</CLASSIFICATION>
<RUN_VALUE>250</RUN_VALUE>
<MONTH_VALUE>500</MONTH_VALUE>
<QUARTER_VALUE>500</QUARTER_VALUE>
<YEAR_VALUE>500</YEAR_VALUE>
</ROW>
<ROW>
<GRE>org1</GRE>
<ORGANIZATION>Finance</ORGANIZATION>
<FULL_NAME>test2</FULL_NAME>
<ELEMENT_NAME>VOLUNTARY AD AND D</ELEMENT_NAME>
<CLASSIFICATION>Voluntary Deductions</CLASSIFICATION>
<RUN_VALUE>5.19</RUN_VALUE>
<MONTH_VALUE>10.38</MONTH_VALUE>
<QUARTER_VALUE>10.38</QUARTER_VALUE>
<YEAR_VALUE>10.38</YEAR_VALUE>
</ROW>
<ROW>
<GRE>org1</GRE>
<ORGANIZATION>Finance</ORGANIZATION>
<FULL_NAME>test3</FULL_NAME>
<ELEMENT_NAME>HMO MEDICAL</ELEMENT_NAME>
<CLASSIFICATION>Pre-Tax Deductions</CLASSIFICATION>
<RUN_VALUE>19.67</RUN_VALUE>
<MONTH_VALUE>39.34</MONTH_VALUE>
<QUARTER_VALUE>39.34</QUARTER_VALUE>
<YEAR_VALUE>39.34</YEAR_VALUE>
</ROW>
<ROW>
<GRE>org1</GRE>
<ORGANIZATION>Finance</ORGANIZATION>
<FULL_NAME>test4</FULL_NAME>
<ELEMENT_NAME>PENSION NR DC</ELEMENT_NAME>
<CLASSIFICATION>Pre-Tax Deductions</CLASSIFICATION>
<RUN_VALUE>0</RUN_VALUE>
<MONTH_VALUE>360</MONTH_VALUE>
<QUARTER_VALUE>360</QUARTER_VALUE>
<YEAR_VALUE>360</YEAR_VALUE>
</ROW>
</ROWSET>
In the template I group the data based on CLASSIFICATION and then sort on the same column CLASSIFICATION. I have a page-break applied for every group.
When I generate the PDF, I am not getting the page-breaks for every group. Instead some of them are displayed in the same page.
But when I remove the sorting that I had in the template on the column CLASSIFICATION, I am getting the output in the desired way but not in a sorted order.
kumarHi All,
I am using MS-WORD 2007 and BI Publisher desktop 10.1.3.3.3.
When I use split-by-page-break, splitting is performed for every line .. but not for group of lines.
Can anybody throw some light on this?
FYI...
I am using this code:
?if: position() mod 6= 0?
?split-by-page-break:?
?end if?
(Of course with in tags)
in G_LINES loop.
Can anybody help me out :-(
--Saritha -
Issue with PTO (Paid Time Off) quota generation
Hi All,
We have an issue with quota generation of PTO for our employees.
The issue goes like this:
We have a Paid time off for employees 5weeks( 200 hrs) for employees who have worked less than 5 years.
we have paid time off for employees 6 weeks ( 240 hrs) for employees who have worked more than 5 years.
we have the following logic that has to go in this config:
-- Our fiscal year starts on Feb 1st and ends on Jan end or Feb starts which has a full week of working days. ( ex: if 01/31/2012 falls on a Thursday the following Monday which has full 5 day working week would be the end of the fiscal year).
-- Depending on the working hours of the employees and the date of joining for the first year ( for new hires)0041 info type the eligibility gets varied and reduced. Ex( employees who joins on start of fiscal year and works 40hrs per week schedules is eligible for 200hrs of PTO. Employees who join in the month of august and works for 35 hrs per week ( i.e mid of fiscal year) would get 91 hrs of PTO.
I need to put this in the system. I am thinking this could be done with out tweaking PCR.I need help in configuring this in Absence quotas as to what are the things i need change in system config and how do i do it. Please help with some screen shots if possible. I really need this to get it done ASAP. Looking forward for help.
Thanks,
Chowdary.We use TM00 schema. Can i call TS15 and TS 12 rules into TM00 acheieve my issue of quota entilements?
Iam doing this because my businees needs to see if an employee chages his work schedule from 40 to 30 or 20 etc.. the PTO has to vary accordingly.
As the minimum eligibility is to work for 20 hrs to avail the PTO days. If at any point the employee drops it under 20 he will not be eligible till he work any this >= 20hrs per month so the evaluation has to check periodically to update the quota availability.... I need help plz suggest ... -
Issues with iMessage when switching data carrier (wifi - cellular)
So I have had this issue with my 5S and now my 6+ in iMessage. Not *always* but often enough I've run into issues sending messages via iMessage when I associate with wifi in that they don't send. I'll get an error message saying "not delivered" and it will stack as many outgoing messages I try to send. However, if I force the first message to send as text, subsequent messages will go through afterwards without issue. If I go from wifi to cellular I have no issues whatsoever and when I have these issues on wifi, my data works fine (incoming emails, Facebook notifications, etc.). I used to run cellular data only because I had unlimited but now I have a cap so I intend on using wifi when possible...but to have to send my first message as a text just so I can use iMessage is annoying...
Hi there BigDogg795,
I would recommend taking a look at the troubleshooting steps for iMessage found in the article below.
iOS: Troubleshooting Messages - Apple Support
To resolve issues with sending and receiving iMessages, follow these steps
Check iMessage system status for current service issues.
Go to Settings > Messages > Send & Receive and make sure that you registered iMessage with your phone number or Apple ID and that you selected iMessage for use. If the phone number or Apple ID isn't available for use, troubleshoot iMessage registration.
Open Safari and navigate to www.apple.com to verify data connectivity. If a data connection isn't available, troubleshoot cellular data or a Wi-Fi connection.
iMessage over cellular data might not be available while you're on a call. Only 3G and faster GSM networks support simultaneous data and voice calls. Learn which network your phone supports. If your network doesn't support simultaneous data and voice calls, go to Settings > Wi-Fi and turn Wi-Fi on to use iMessage while you're on a call.
Restart your device.
Tap Settings > General > Reset > Reset Network Settings on your iPhone.
If you still can't send or receive an iMessage, follow these steps
Make sure that the contact trying to message you isn't blocked in Settings > Messages > Blocked.
Make sure that the contact you're trying to send a message to is registered with iMessage.
If the issue occurs with a specific contact or contacts, back up or forward important messages and delete your current messaging threads with the contact. Create a new message to the contact and try again.
If the issue occurs with a specific contact or contacts, delete and recreate the contact in the Contacts app. Create a new message to the newly created contact and try again.
Back up and restore your device as new.
-Griff W. -
Issues with WebForm performance
Hi,
We had migrated a new application from UAT to PROD and we encounter webform performance issues with the following actions..
After login, the first form you open it is
always slow. After this you can switch from one form to another without a
delay.
Then once you change any data – the next time
you access a form it gets delayed.
The point to be noted is, it doesnt have any performance issues in the UAT environment and the configuration settings,essbase cache settings are all the same. We did try to move the EPM system to a new server to see if this is a hardware issue but no luck, the performance issues still exist. The consumption of the CPU/memory has been checked and it is proved that the form opening delay has nothing to do with lack of memory.
The JVM head settings is set up at 4GB which is infact higher than that of the UAT environment(2GB).
runs on Windows server2008,11.1.2.1.600 EPM serve, has planning,reporting,foundation on one server (32GB ram) and essbase on another server (32GB ram). Any help is appreciated.
Please find attached the planning logs below and there is nothing mentioned in the hyperionplanning error logs.-----------------------------------------------------------------------------------------------------------------------------------------------------------------
<Nov 5, 2013 8:05:43 PM CET> <Info> <Security> <BEA-090905> <Disabling CryptoJ JCE Provider self-integrity check for better startup performance. To enable this check, specify -Dweblogic.security.allowCryptoJDefaultJCEVerification=true>
<Nov 5, 2013 8:05:43 PM CET> <Info> <Security> <BEA-090906> <Changing the default Random Number Generator in RSA CryptoJ from ECDRBG to FIPS186PRNG. To disable this change, specify -Dweblogic.security.allowCryptoJDefaultPRNG=true>
<Nov 5, 2013 8:05:44 PM CET> <Info> <WebLogicServer> <BEA-000377> <Starting WebLogic Server with Oracle JRockit(R) Version R28.0.2-11-135406-1.6.0_20-20100624-2119-windows-x86_64 from Oracle Corporation>
<Nov 5, 2013 8:05:46 PM CET> <Info> <Management> <BEA-141107> <Version: WebLogic Server 10.3.4.0 Fri Dec 17 20:47:33 PST 2010 1384255 >
<Nov 5, 2013 8:05:48 PM CET> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to STARTING>
<Nov 5, 2013 8:05:48 PM CET> <Info> <WorkManager> <BEA-002900> <Initializing self-tuning thread pool>
<Nov 5, 2013 8:05:48 PM CET> <Notice> <Log Management> <BEA-170019> <The server log file C:\Oracle\Middleware\user_projects\domains\EPMSystem\servers\Planning0\logs\Planning0.log is opened. All server side log events will be written to this file.>
<Nov 5, 2013 8:06:22 PM CET> <Notice> <Security> <BEA-090082> <Security initializing using security realm myrealm.>
<Nov 5, 2013 8:06:28 PM CET> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to STANDBY>
<Nov 5, 2013 8:06:28 PM CET> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to STARTING>
Calling getConnection()
return weblogic.management.jmx.mbeanserver.WLSMBeanServer@327b36fb
Calling getDomainConfiguration()
Calling getConnection()
return weblogic.management.jmx.mbeanserver.WLSMBeanServer@327b36fb
Calling getRuntimeService()
Calling getConnection()
return weblogic.management.jmx.mbeanserver.WLSMBeanServer@327b36fb
return com.bea:Name=RuntimeService,Type=weblogic.management.mbeanservers.runtime.RuntimeServiceMBean
return com.bea:Name=EPMSystem,Type=Domain
Calling getConnection()
return weblogic.management.jmx.mbeanserver.WLSMBeanServer@327b36fb
Domain location is 'C:\Oracle\Middleware\user_projects\domains\EPMSystem'
Calling getRuntimeService()
return com.bea:Name=RuntimeService,Type=weblogic.management.mbeanservers.runtime.RuntimeServiceMBean
Calling getConnection()
return weblogic.management.jmx.mbeanserver.WLSMBeanServer@327b36fb
Calling getConnection()
return weblogic.management.jmx.mbeanserver.WLSMBeanServer@327b36fb
Calling getConnection()
return weblogic.management.jmx.mbeanserver.WLSMBeanServer@327b36fb
Calling getConnection()
return weblogic.management.jmx.mbeanserver.WLSMBeanServer@327b36fb
Checking C:\Oracle\Middleware\user_projects\domains\EPMSystem\servers\Planning0\registry_update.xml file
EPM_ORACLE_HOME: C:\Oracle\Middleware\EPMSystem11R1
Template for PLANNING#11.1.2.0: C:\Oracle\Middleware\EPMSystem11R1\common\templates\applications\epm_planning_11.1.2.1.jar
Dependencies for C:\Oracle\Middleware\EPMSystem11R1\common\templates\applications\epm_planning_11.1.2.1.jar: []
BPMUI shared webapp not referenced from PLANNING#11.1.2.0
Application name: PLANNING#11.1.2.0
Application source: HyperionPlanning.ear
Server name: Planning0
Server port: 8300
Server SSL port: 8343
Application context: HyperionPlanning
Registry product type: PLANNING_PRODUCT
Registry physical web application type: PLANNING_WEBAPP
weblogic.Name property is 'Planning0', seems to be WebLogic mode
registry.isRegistryDatabaseCreated()true
Registry was initialized sucessfully
Executing pre custom update for PLANNING#11.1.2.0
EPM_ORACLE_INSTANCE: C:\Oracle\Middleware\user_projects\epmsystem1
Physical Web App found
Web app already linked to some application server: false
The registry was not modifyed because it already containse all sturctures
Web app is already linked to the logical web app
No needs to run custom updater for PLANNING#11.1.2.0
loggingUpdatePLANNING.block file exist or the system is running in the Fusion mode, skipping logging.xml configuration
Planning locale: en_US
<Nov 5, 2013 8:06:39 PM CET> <Notice> <Log Management> <BEA-170027> <The Server has established connection with the Domain level Diagnostic Service successfully.>
<Nov 5, 2013 8:06:39 PM CET> <Notice> <Cluster> <BEA-000197> <Listening for announcements from cluster using unicast cluster messaging>
<Nov 5, 2013 8:06:39 PM CET> <Notice> <Cluster> <BEA-000133> <Waiting to synchronize with other running members of Planning.>
<Nov 5, 2013 8:07:09 PM CET> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to ADMIN>
<Nov 5, 2013 8:07:09 PM CET> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to RESUMING>
<Nov 5, 2013 8:07:09 PM CET> <Notice> <Cluster> <BEA-000162> <Starting "async" replication service with remote cluster address "null">
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Security> <BEA-090171> <Loading the identity certificate and private key stored under the alias DemoIdentity from the jks keystore file C:\Oracle\MIDDLE~1\WLSERV~1.3\server\lib\DemoIdentity.jks.>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Security> <BEA-090169> <Loading trusted certificates from the jks keystore file C:\Oracle\MIDDLE~1\WLSERV~1.3\server\lib\DemoTrust.jks.>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Security> <BEA-090169> <Loading trusted certificates from the jks keystore file C:\Oracle\Middleware\jrockit_160_20\jre\lib\security\cacerts.>
<Nov 5, 2013 8:07:10 PM CET> <Alert> <Security> <BEA-090152> <Demo trusted CA certificate is being used in production mode: [
Version: V3
Subject: CN=CACERT, OU=FOR TESTING ONLY, O=MyOrganization, L=MyTown, ST=MyState, C=US
Signature Algorithm: MD5withRSA, OID = 1.2.840.113549.1.1.4
Key: Sun RSA public key, 512 bits
modulus: 9550192877869244258838480703390456015046425375252278279190673063544122510925482179963329236052146047356415957587628011282484772458983977898996276815440753
public exponent: 65537
Validity: [From: Thu Mar 21 21:12:27 CET 2002,
To: Tue Mar 22 21:12:27 CET 2022]
Issuer: CN=CACERT, OU=FOR TESTING ONLY, O=MyOrganization, L=MyTown, ST=MyState, C=US
SerialNumber: [ 33f10648 fcde0deb 4199921f d64537f4]
Certificate Extensions: 1
[1]: ObjectId: 2.5.29.15 Criticality=true
KeyUsage [
Key_CertSign
Algorithm: [MD5withRSA]
Signature:
0000: 9D 26 4C 29 C8 91 C3 A7 06 C3 24 6F AE B4 F8 82 .&L)......$o....
0010: 80 4D AA CB 7C 79 46 84 81 C4 66 95 F4 1E D8 C4 .M...yF...f.....
0020: E9 B7 D9 7C E2 23 33 A4 B7 21 E0 AA 54 2B 4A FF .....#3..!..T+J.
0030: CB 21 20 88 81 21 DB AC 90 54 D8 7D 79 63 23 3C .! ..!...T..yc#<
] The system is vulnerable to security attacks, since it trusts certificates signed by the demo trusted CA.>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=thawte Primary Root CA - G3,OU=(c) 2008 thawte\, Inc. - For authorized use only,OU=Certification Services Division,O=thawte\, Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=T-TeleSec GlobalRoot Class 3,OU=T-Systems Trust Center,O=T-Systems Enterprise Services GmbH,C=DE". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=T-TeleSec GlobalRoot Class 2,OU=T-Systems Trust Center,O=T-Systems Enterprise Services GmbH,C=DE". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=GlobalSign,O=GlobalSign,OU=GlobalSign Root CA - R3". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "OU=Security Communication RootCA2,O=SECOM Trust Systems CO.\,LTD.,C=JP". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=VeriSign Universal Root Certification Authority,OU=(c) 2008 VeriSign\, Inc. - For authorized use only,OU=VeriSign Trust Network,O=VeriSign\, Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=KEYNECTIS ROOT CA,OU=ROOT,O=KEYNECTIS,C=FR". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=GeoTrust Primary Certification Authority - G3,OU=(c) 2008 GeoTrust Inc. - For authorized use only,O=GeoTrust Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Server> <BEA-002613> <Channel "DefaultSecure[3]" is now listening on 127.0.0.1:8343 for protocols iiops, t3s, CLUSTER-BROADCAST-SECURE, ldaps, https.>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Server> <BEA-002613> <Channel "DefaultSecure[1]" is now listening on fe80:0:0:0:0:5efe:a53:4816:8343 for protocols iiops, t3s, CLUSTER-BROADCAST-SECURE, ldaps, https.>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Server> <BEA-002613> <Channel "DefaultSecure[4]" is now listening on 0:0:0:0:0:0:0:1:8343 for protocols iiops, t3s, CLUSTER-BROADCAST-SECURE, ldaps, https.>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Server> <BEA-002613> <Channel "Default" is now listening on 10.83.72.22:8300 for protocols iiop, t3, CLUSTER-BROADCAST, ldap, snmp, http.>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Server> <BEA-002613> <Channel "Default[3]" is now listening on 127.0.0.1:8300 for protocols iiop, t3, CLUSTER-BROADCAST, ldap, snmp, http.>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Server> <BEA-002613> <Channel "Default[4]" is now listening on 0:0:0:0:0:0:0:1:8300 for protocols iiop, t3, CLUSTER-BROADCAST, ldap, snmp, http.>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Server> <BEA-002613> <Channel "Default[2]" is now listening on fe80:0:0:0:0:ffff:ffff:fffe:8300 for protocols iiop, t3, CLUSTER-BROADCAST, ldap, snmp, http.>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Server> <BEA-002613> <Channel "Default[1]" is now listening on fe80:0:0:0:0:5efe:a53:4816:8300 for protocols iiop, t3, CLUSTER-BROADCAST, ldap, snmp, http.>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Server> <BEA-002613> <Channel "DefaultSecure[2]" is now listening on fe80:0:0:0:0:ffff:ffff:fffe:8343 for protocols iiops, t3s, CLUSTER-BROADCAST-SECURE, ldaps, https.>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <Server> <BEA-002613> <Channel "DefaultSecure" is now listening on 10.83.72.22:8343 for protocols iiops, t3s, CLUSTER-BROADCAST-SECURE, ldaps, https.>
<Nov 5, 2013 8:07:10 PM CET> <Warning> <Server> <BEA-002611> <Hostname "WIPLPRD01.svc.unicc.org", maps to multiple IP addresses: 10.83.72.22, 0:0:0:0:0:0:0:1>
<Nov 5, 2013 8:07:10 PM CET> <Notice> <WebLogicServer> <BEA-000330> <Started WebLogic Managed Server "Planning0" for domain "EPMSystem" running in Production Mode>
<Nov 5, 2013 8:07:12 PM CET> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to RUNNING>
<Nov 5, 2013 8:07:12 PM CET> <Notice> <WebLogicServer> <BEA-000360> <Server started in RUNNING mode>
using java.library.path: C:\Oracle\Middleware\EPMSystem11R1/products/Planning/lib64;C:\Oracle\Middleware\EPMSystem11R1/bin;C:\Oracle\Middleware\EPMSystem11R1/common/EssbaseRTC-64/11.1.2.0/bin;C:\Oracle\MIDDLE~1\patch_wls1034\profiles\default\native;C:\Oracle\MIDDLE~1\WLSERV~1.3\server\native\win\x64;C:\Oracle\MIDDLE~1\WLSERV~1.3\server\bin;C:\Oracle\MIDDLE~1\modules\ORGAPA~1.1\bin;C:\Oracle\MIDDLE~1\JROCKI~1\jre\bin;C:\Oracle\MIDDLE~1\JROCKI~1\bin;C:\Oracle\MIDDLE~1\WLSERV~1.3\server\native\win\x64\oci920_8
EPM_ORACLE_HOME (C:\Oracle\Middleware\EPMSystem11R1) is set from JVM property "EPM_ORACLE_HOME".
using Java property for Hyperion Home C:\Oracle\Middleware\EPMSystem11R1
EPM_ORACLE_INSTANCE (C:\Oracle\Middleware\user_projects\epmsystem1) is set from JVM property[EPM_ORACLE_INSTANCE].
Reaquired task list lease: Tue Nov 05 20:11:49 CET 2013: 1383678709156
Seeking ESAPI.properties
Found in 'org.owasp.esapi.resources' directory: C:\Oracle\Middleware\EPMSystem11R1\products\Planning\config\esapi\ESAPI.properties
Loaded 'ESAPI.properties' properties file
Seeking validation.properties
Found in 'org.owasp.esapi.resources' directory: C:\Oracle\Middleware\EPMSystem11R1\products\Planning\config\esapi\validation.properties
Loaded 'validation.properties' properties file
Seeking antisamy-esapi.xml
Found in 'org.owasp.esapi.resources' directory: C:\Oracle\Middleware\EPMSystem11R1\products\Planning\config\esapi\antisamy-esapi.xml
EnterData_Inner Processing Time:424
2013-11-05 20:14:47,454 INFO Thread-51 calcmgr.launch - Date/Time Started: 2013/11/05:20:14:47.452 CET Server/Application/Database: localhost/1415_WP/AWP Business Rule Name: WPA_Count By Planning user: wipoadmin Values entered for run-time prompts: [Variable] Wrk_Scenario:"Work_Plan_2014"[Variable] Funds:"Regular"[Variable] Units:"0001"
- Date/Time Started: 2013/11/05:20:14:47.452 CET Server/Application/Database: localhost/1415_WP/AWP Business Rule Name: WPA_Count By Planning user: wipoadmin Values entered for run-time prompts: [Variable] Wrk_Scenario:"Work_Plan_2014"[Variable] Funds:"Regular"[Variable] Units:"0001"
2013-11-05 20:14:54,066 INFO Thread-51 calcmgr.launch - Date/Time Ended: 2013/11/05:20:14:54.066 CET Server/Application/Database: localhost/1415_WP/AWP Business Rule Name: WPA_Count By Planning user: wipoadmin.
- Date/Time Ended: 2013/11/05:20:14:54.066 CET Server/Application/Database: localhost/1415_WP/AWP Business Rule Name: WPA_Count By Planning user: wipoadmin.
EnterData_Inner Processing Time:64
EnterData_Inner Processing Time:15
EnterData_Inner Processing Time:359
EnterData_Inner Processing Time:2
EnterData_Inner Processing Time:53
EnterData_Inner Processing Time:4
EnterData_Inner Processing Time:7
EPM_ORACLE_INSTANCE (C:\Oracle\Middleware\user_projects\epmsystem1) is set from JVM property[EPM_ORACLE_INSTANCE].
EPM_ORACLE_INSTANCE (C:\Oracle\Middleware\user_projects\epmsystem1) is set from JVM property[EPM_ORACLE_INSTANCE].
EPM_ORACLE_INSTANCE (C:\Oracle\Middleware\user_projects\epmsystem1) is set from JVM property[EPM_ORACLE_INSTANCE].
Setting HBR Mode to: 2
In lookupBRLWA()
Found HBR product = ESSBASE_PRODUCT
Found HBR product = ESSBASE_PRODUCT
Found HBR product = ESSBASE_PRODUCT
HBR LWA Component = Default
Default HBR = http://WIPLPRD01.svc.unicc.org:19000/eas
In getDBDetails()
Found HBR product = ESSBASE_PRODUCT
In lookupBRLWA()
Found HBR product = ESSBASE_PRODUCT
Found HBR product = ESSBASE_PRODUCT
=2013-11-05 20:35:08,234 WARN [ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)' com.hyperion.hbr.security.HbrSecurityAPI - Error retrieving user by identity
- Error retrieving user by identity
Embedded HBR initialized.
EnterData_Inner Processing Time:6
EnterData_Inner Processing Time:867
[Tue Nov 05 20:35:33 CET 2013] Planning successfully notified HBR repository.
EnterData_Inner Processing Time:7
2013-11-05 20:40:38,613 INFO Thread-67 calcmgr.launch - Date/Time Started: 2013/11/05:20:40:38.606 CET Server/Application/Database: localhost/1415_WP/AWP Business Rule Name: NonPersonnel_Calc By Planning user: wipoadmin Values entered for run-time prompts: [Variable] Funds:"Regular"[Variable] Units:"0001"[Variable] Wrk_Scenario:"Work_Plan_2014"
- Date/Time Started: 2013/11/05:20:40:38.606 CET Server/Application/Database: localhost/1415_WP/AWP Business Rule Name: NonPersonnel_Calc By Planning user: wipoadmin Values entered for run-time prompts: [Variable] Funds:"Regular"[Variable] Units:"0001"[Variable] Wrk_Scenario:"Work_Plan_2014"
2013-11-05 20:40:47,241 INFO Thread-67 calcmgr.launch - Date/Time Ended: 2013/11/05:20:40:47.241 CET Server/Application/Database: localhost/1415_WP/AWP Business Rule Name: NonPersonnel_Calc By Planning user: wipoadmin.
- Date/Time Ended: 2013/11/05:20:40:47.241 CET Server/Application/Database: localhost/1415_WP/AWP Business Rule Name: NonPersonnel_Calc By Planning user: wipoadmin.
EnterData_Inner Processing Time:44
EnterData_Inner Processing Time:2
EnterData_Inner Processing Time:525
EnterData_Inner Processing Time:1
Reaquired task list lease: Tue Nov 05 20:41:49 CET 2013: 1383680509246I already replied there but it seems no moderator is willing to approve my reply so it never shows up.
So I'll try replying in here instead:
I never thought it could be an emulator issue, I thought I had done something wrong to begin with. So I take having performance issues with tiled layer is not a common problem I suppose?
I'm using MOTODEV SDK platform, A1200 model (motorola). -
Issues with using 3 monitors on 2 external gpu
Hi,
I have some issues with configuring Xorg to use 3 monitors. I have 2 external graphic cards (same model, no SLI). Monitors connected to the first gpu are recognized ok but I can't configure my 3rd monitor conencted to the second gpu via HDMI nor DVI.
1st is recognized as DVI-I-1, 2nd is DP-1 in first card, 3rd monitor is in second card (bus 22:00.0) as DP-1-2 (also tried connecting as DVI-I-2). I can see them in Xorg log but I can't configure my 3rd monitor via kscreen nor xrandr. :-/
lspci |grep VGA:
03:00.0 VGA compatible controller: NVIDIA Corporation GF108GL [Quadro 600] (rev a1)
22:00.0 VGA compatible controller: NVIDIA Corporation GF108GL [Quadro 600] (rev a1)
xrandr:
Screen 0: minimum 320 x 200, current 3840 x 1080, maximum 8192 x 8192
DVI-I-1 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 527mm x 297mm
1920x1080 60.0*+
1600x900 60.0
1280x1024 75.0 60.0
1152x864 75.0
1024x768 75.1 60.0
800x600 75.0 60.3
640x480 75.0 60.0
720x400 70.1
DP-1 connected 1920x1080+1920+0 (normal left inverted right x axis y axis) 527mm x 297mm
1920x1080 60.0*+
1600x900 60.0
1280x1024 75.0 60.0
1152x864 75.0
1024x768 75.1 60.0
800x600 75.0 60.3
640x480 75.0 60.0
720x400 70.1
Xorg config (autoconfig enable only 2 monitors, I generated config and tried to edit it with no luck, I noticed there is PCI:34:0:0 generated by Xorg so I also tried to change it to 22:0:0, I also tried to add that option "Monitor-<output>" but same result):
Section "ServerLayout"
Identifier "X.org Configured"
#Screen 0 "Screen0" 0 0
#Screen 1 "Screen1" RightOf "Screen0"
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc/"
FontPath "/usr/share/fonts/TTF/"
FontPath "/usr/share/fonts/OTF/"
FontPath "/usr/share/fonts/Type1/"
FontPath "/usr/share/fonts/100dpi/"
FontPath "/usr/share/fonts/75dpi/"
EndSection
Section "Module"
Load "glx"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "DELL"
Option "Monitor-DVI-I-1" "DVI-I-1"
EndSection
Section "Monitor"
Identifier "Monitor1"
VendorName "DELL"
Option "Monitor-DP-1" "DP-1"
EndSection
Section "Monitor"
Identifier "Monitor2"
VendorName "DELL"
Option "Monitor-DP-1-2" "DP-1-2"
EndSection
Section "Device"
Identifier "Card0"
Driver "nouveau"
BusID "PCI:3:0:0"
Option "Monitor-DVI-I-1"
Option "Monitor-DP-1"
EndSection
Section "Device"
Identifier "Card1"
Driver "nouveau"
BusID "PCI:34:0:0"
Option "Monitor-DP-1-2"
EndSection
Xorg log (I can see that monitor at time 1767.316):
[ 1766.959]
X.Org X Server 1.14.5
Release Date: 2013-12-12
[ 1766.960] X Protocol Version 11, Revision 0
[ 1766.960] Build Operating System: Linux 3.12.5-1-ARCH x86_64
[ 1766.960] Current Operating System: Linux CZ09DT1XM5002 3.12.5-1-ARCH #1 SMP PREEMPT Thu Dec 12 12:57:31 CET 2013 x86_64
[ 1766.960] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=e2c593e5-b0f4-4c74-84fd-5a88db345ca4 rw quiet
[ 1766.961] Build Date: 13 December 2013 03:11:42PM
[ 1766.962]
[ 1766.962] Current version of pixman: 0.32.4
[ 1766.963] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 1766.963] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 1766.965] (==) Log file: "/var/log/Xorg.1.log", Time: Thu Jan 2 12:43:56 2014
[ 1766.965] (++) Using config file: "/etc/X11/xorg.conf.d/20-multimonitor.conf"
[ 1766.966] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 1766.966] (==) ServerLayout "X.org Configured"
[ 1766.966] (==) No screen section available. Using defaults.
[ 1766.966] (**) |-->Screen "Default Screen Section" (0)
[ 1766.966] (**) | |-->Monitor "<default monitor>"
[ 1766.966] (==) No device specified for screen "Default Screen Section".
Using the first device section listed.
[ 1766.966] (**) | |-->Device "Card0"
[ 1766.966] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 1766.966] (**) |-->Input Device "Mouse0"
[ 1766.966] (**) |-->Input Device "Keyboard0"
[ 1766.966] (==) Automatically adding devices
[ 1766.966] (==) Automatically enabling devices
[ 1766.966] (==) Automatically adding GPU devices
[ 1766.966] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 1766.966] Entry deleted from font path.
[ 1766.966] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 1766.966] Entry deleted from font path.
[ 1766.966] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 1766.966] Entry deleted from font path.
[ 1766.966] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 1766.967] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 1766.967] Entry deleted from font path.
[ 1766.967] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 1766.967] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 1766.967] Entry deleted from font path.
[ 1766.967] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 1766.967] Entry deleted from font path.
[ 1766.967] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 1766.967] Entry deleted from font path.
[ 1766.967] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 1766.967] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 1766.967] Entry deleted from font path.
[ 1766.967] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 1766.967] (**) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/
[ 1766.967] (**) ModulePath set to "/usr/lib/xorg/modules"
[ 1766.967] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
[ 1766.967] (WW) Disabling Mouse0
[ 1766.967] (WW) Disabling Keyboard0
[ 1766.967] (II) Loader magic: 0x7fec20
[ 1766.967] (II) Module ABI versions:
[ 1766.967] X.Org ANSI C Emulation: 0.4
[ 1766.967] X.Org Video Driver: 14.1
[ 1766.967] X.Org XInput driver : 19.1
[ 1766.967] X.Org Server Extension : 7.0
[ 1766.967] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 1766.967] (II) xfree86: Adding drm device (/dev/dri/card1)
[ 1767.169] (--) PCI:*(0:3:0:0) 10de:0df8:10de:0835 rev 161, Mem @ 0xc6000000/16777216, 0xc8000000/134217728, 0xd0000000/33554432, I/O @ 0x00007000/128, BIOS @ 0x????????/524288
[ 1767.169] (--) PCI: (0:34:0:0) 10de:0df8:10de:0835 rev 161, Mem @ 0xfa000000/16777216, 0xf0000000/134217728, 0xf8000000/33554432, I/O @ 0x0000f000/128, BIOS @ 0x????????/524288
[ 1767.169] Initializing built-in extension Generic Event Extension
[ 1767.170] Initializing built-in extension SHAPE
[ 1767.170] Initializing built-in extension MIT-SHM
[ 1767.170] Initializing built-in extension XInputExtension
[ 1767.171] Initializing built-in extension XTEST
[ 1767.171] Initializing built-in extension BIG-REQUESTS
[ 1767.172] Initializing built-in extension SYNC
[ 1767.172] Initializing built-in extension XKEYBOARD
[ 1767.172] Initializing built-in extension XC-MISC
[ 1767.173] Initializing built-in extension SECURITY
[ 1767.173] Initializing built-in extension XINERAMA
[ 1767.174] Initializing built-in extension XFIXES
[ 1767.174] Initializing built-in extension RENDER
[ 1767.174] Initializing built-in extension RANDR
[ 1767.175] Initializing built-in extension COMPOSITE
[ 1767.175] Initializing built-in extension DAMAGE
[ 1767.175] Initializing built-in extension MIT-SCREEN-SAVER
[ 1767.176] Initializing built-in extension DOUBLE-BUFFER
[ 1767.176] Initializing built-in extension RECORD
[ 1767.176] Initializing built-in extension DPMS
[ 1767.177] Initializing built-in extension X-Resource
[ 1767.177] Initializing built-in extension XVideo
[ 1767.177] Initializing built-in extension XVideo-MotionCompensation
[ 1767.178] Initializing built-in extension XFree86-VidModeExtension
[ 1767.178] Initializing built-in extension XFree86-DGA
[ 1767.178] Initializing built-in extension XFree86-DRI
[ 1767.179] Initializing built-in extension DRI2
[ 1767.179] (II) "glx" will be loaded. This was enabled by default and also specified in the config file.
[ 1767.179] (II) LoadModule: "glx"
[ 1767.179] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 1767.179] (II) Module glx: vendor="X.Org Foundation"
[ 1767.179] compiled for 1.14.5, module version = 1.0.0
[ 1767.179] ABI class: X.Org Server Extension, version 7.0
[ 1767.179] (==) AIGLX enabled
[ 1767.180] Loading extension GLX
[ 1767.180] (II) LoadModule: "nouveau"
[ 1767.180] (II) Loading /usr/lib/xorg/modules/drivers/nouveau_drv.so
[ 1767.180] (II) Module nouveau: vendor="X.Org Foundation"
[ 1767.180] compiled for 1.14.4, module version = 1.0.10
[ 1767.180] Module class: X.Org Video Driver
[ 1767.180] ABI class: X.Org Video Driver, version 14.1
[ 1767.180] (II) NOUVEAU driver
[ 1767.180] (II) NOUVEAU driver for NVIDIA chipset families :
[ 1767.180] RIVA TNT (NV04)
[ 1767.180] RIVA TNT2 (NV05)
[ 1767.180] GeForce 256 (NV10)
[ 1767.180] GeForce 2 (NV11, NV15)
[ 1767.180] GeForce 4MX (NV17, NV18)
[ 1767.180] GeForce 3 (NV20)
[ 1767.180] GeForce 4Ti (NV25, NV28)
[ 1767.180] GeForce FX (NV3x)
[ 1767.180] GeForce 6 (NV4x)
[ 1767.180] GeForce 7 (G7x)
[ 1767.180] GeForce 8 (G8x)
[ 1767.180] GeForce GTX 200 (NVA0)
[ 1767.180] GeForce GTX 400 (NVC0)
[ 1767.180] (--) using VT number 3
[ 1767.182] (II) [drm] nouveau interface version: 1.1.1
[ 1767.183] (II) [drm] nouveau interface version: 1.1.1
[ 1767.183] (II) Loading sub module "dri2"
[ 1767.183] (II) LoadModule: "dri2"
[ 1767.183] (II) Module "dri2" already built-in
[ 1767.183] (--) NOUVEAU(0): Chipset: "NVIDIA NVC1"
[ 1767.183] (II) NOUVEAU(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 1767.183] (==) NOUVEAU(0): Depth 24, (--) framebuffer bpp 32
[ 1767.183] (==) NOUVEAU(0): RGB weight 888
[ 1767.183] (==) NOUVEAU(0): Default visual is TrueColor
[ 1767.183] (==) NOUVEAU(0): Using HW cursor
[ 1767.183] (==) NOUVEAU(0): GLX sync to VBlank disabled.
[ 1767.183] (==) NOUVEAU(0): Page flipping enabled
[ 1767.183] (==) NOUVEAU(0): Swap limit set to 2 [Max allowed 2]
[ 1767.222] (II) NOUVEAU(0): Output DVI-I-1 has no monitor section
[ 1767.230] (II) NOUVEAU(0): Output DP-1 has no monitor section
[ 1767.265] (II) NOUVEAU(0): EDID for output DVI-I-1
[ 1767.265] (II) NOUVEAU(0): Manufacturer: DEL Model: a09b Serial#: 827608652
[ 1767.265] (II) NOUVEAU(0): Year: 2013 Week: 41
[ 1767.265] (II) NOUVEAU(0): EDID Version: 1.3
[ 1767.265] (II) NOUVEAU(0): Digital Display Input
[ 1767.265] (II) NOUVEAU(0): Max Image Size [cm]: horiz.: 53 vert.: 30
[ 1767.265] (II) NOUVEAU(0): Gamma: 2.20
[ 1767.265] (II) NOUVEAU(0): DPMS capabilities: StandBy Suspend Off
[ 1767.265] (II) NOUVEAU(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 1767.265] (II) NOUVEAU(0): First detailed timing is preferred mode
[ 1767.265] (II) NOUVEAU(0): redX: 0.650 redY: 0.338 greenX: 0.320 greenY: 0.613
[ 1767.265] (II) NOUVEAU(0): blueX: 0.154 blueY: 0.061 whiteX: 0.313 whiteY: 0.329
[ 1767.265] (II) NOUVEAU(0): Supported established timings:
[ 1767.265] (II) NOUVEAU(0): 720x400@70Hz
[ 1767.265] (II) NOUVEAU(0): 640x480@60Hz
[ 1767.265] (II) NOUVEAU(0): 640x480@75Hz
[ 1767.265] (II) NOUVEAU(0): 800x600@60Hz
[ 1767.265] (II) NOUVEAU(0): 800x600@75Hz
[ 1767.265] (II) NOUVEAU(0): 1024x768@60Hz
[ 1767.265] (II) NOUVEAU(0): 1024x768@75Hz
[ 1767.265] (II) NOUVEAU(0): 1280x1024@75Hz
[ 1767.265] (II) NOUVEAU(0): Manufacturer's mask: 0
[ 1767.265] (II) NOUVEAU(0): Supported standard timings:
[ 1767.265] (II) NOUVEAU(0): #0: hsize: 1152 vsize 864 refresh: 75 vid: 20337
[ 1767.265] (II) NOUVEAU(0): #1: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 1767.265] (II) NOUVEAU(0): #2: hsize: 1600 vsize 900 refresh: 60 vid: 49321
[ 1767.265] (II) NOUVEAU(0): #3: hsize: 1920 vsize 1080 refresh: 60 vid: 49361
[ 1767.265] (II) NOUVEAU(0): Supported detailed timing:
[ 1767.265] (II) NOUVEAU(0): clock: 148.5 MHz Image Size: 527 x 297 mm
[ 1767.265] (II) NOUVEAU(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 1767.265] (II) NOUVEAU(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 1767.265] (II) NOUVEAU(0): Serial No: 36WJX3A91TNL
[ 1767.265] (II) NOUVEAU(0): Monitor name: DELL P2414H
[ 1767.265] (II) NOUVEAU(0): Ranges: V min: 56 V max: 76 Hz, H min: 30 H max: 83 kHz, PixClock max 175 MHz
[ 1767.265] (II) NOUVEAU(0): EDID (in hex):
[ 1767.265] (II) NOUVEAU(0): 00ffffffffffff0010ac9ba04c4e5431
[ 1767.265] (II) NOUVEAU(0): 2917010380351e78eaa0a5a656529d27
[ 1767.265] (II) NOUVEAU(0): 0f5054a54b00714f8180a9c0d1c00101
[ 1767.265] (II) NOUVEAU(0): 010101010101023a801871382d40582c
[ 1767.265] (II) NOUVEAU(0): 45000f292100001e000000ff00333657
[ 1767.265] (II) NOUVEAU(0): 4a5833413931544e4c0a000000fc0044
[ 1767.265] (II) NOUVEAU(0): 454c4c205032343134480a20000000fd
[ 1767.265] (II) NOUVEAU(0): 00384c1e5311000a20202020202000c2
[ 1767.265] (II) NOUVEAU(0): Printing probed modes for output DVI-I-1
[ 1767.265] (II) NOUVEAU(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[ 1767.265] (II) NOUVEAU(0): Modeline "1600x900"x60.0 118.96 1600 1696 1864 2128 900 901 904 932 -hsync +vsync (55.9 kHz)
[ 1767.265] (II) NOUVEAU(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 1767.265] (II) NOUVEAU(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 1767.265] (II) NOUVEAU(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 1767.265] (II) NOUVEAU(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz e)
[ 1767.265] (II) NOUVEAU(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 1767.265] (II) NOUVEAU(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 1767.265] (II) NOUVEAU(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 1767.265] (II) NOUVEAU(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 1767.265] (II) NOUVEAU(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 1767.265] (II) NOUVEAU(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 1767.273] (II) NOUVEAU(0): EDID for output DP-1
[ 1767.273] (II) NOUVEAU(0): Manufacturer: DEL Model: a09a Serial#: 844123724
[ 1767.273] (II) NOUVEAU(0): Year: 2013 Week: 41
[ 1767.273] (II) NOUVEAU(0): EDID Version: 1.4
[ 1767.273] (II) NOUVEAU(0): Digital Display Input
[ 1767.273] (II) NOUVEAU(0): 8 bits per channel
[ 1767.273] (II) NOUVEAU(0): Digital interface is DisplayPort
[ 1767.273] (II) NOUVEAU(0): Max Image Size [cm]: horiz.: 53 vert.: 30
[ 1767.273] (II) NOUVEAU(0): Gamma: 2.20
[ 1767.273] (II) NOUVEAU(0): DPMS capabilities: Off
[ 1767.273] (II) NOUVEAU(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 YCrCb 4:2:2
[ 1767.273] (II) NOUVEAU(0): First detailed timing is preferred mode
[ 1767.273] (II) NOUVEAU(0): Preferred mode is native pixel format and refresh rate
[ 1767.273] (II) NOUVEAU(0): redX: 0.650 redY: 0.338 greenX: 0.320 greenY: 0.613
[ 1767.273] (II) NOUVEAU(0): blueX: 0.154 blueY: 0.061 whiteX: 0.313 whiteY: 0.329
[ 1767.273] (II) NOUVEAU(0): Supported established timings:
[ 1767.273] (II) NOUVEAU(0): 720x400@70Hz
[ 1767.273] (II) NOUVEAU(0): 640x480@60Hz
[ 1767.273] (II) NOUVEAU(0): 640x480@75Hz
[ 1767.273] (II) NOUVEAU(0): 800x600@60Hz
[ 1767.273] (II) NOUVEAU(0): 800x600@75Hz
[ 1767.273] (II) NOUVEAU(0): 1024x768@60Hz
[ 1767.273] (II) NOUVEAU(0): 1024x768@75Hz
[ 1767.273] (II) NOUVEAU(0): 1280x1024@75Hz
[ 1767.273] (II) NOUVEAU(0): Manufacturer's mask: 0
[ 1767.273] (II) NOUVEAU(0): Supported standard timings:
[ 1767.273] (II) NOUVEAU(0): #0: hsize: 1152 vsize 864 refresh: 75 vid: 20337
[ 1767.273] (II) NOUVEAU(0): #1: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 1767.273] (II) NOUVEAU(0): #2: hsize: 1600 vsize 900 refresh: 60 vid: 49321
[ 1767.273] (II) NOUVEAU(0): #3: hsize: 1920 vsize 1080 refresh: 60 vid: 49361
[ 1767.273] (II) NOUVEAU(0): Supported detailed timing:
[ 1767.273] (II) NOUVEAU(0): clock: 148.5 MHz Image Size: 527 x 297 mm
[ 1767.273] (II) NOUVEAU(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 1767.273] (II) NOUVEAU(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 1767.273] (II) NOUVEAU(0): Serial No: 36WJX3A92PNL
[ 1767.273] (II) NOUVEAU(0): Monitor name: DELL P2414H
[ 1767.273] (II) NOUVEAU(0): Ranges: V min: 56 V max: 76 Hz, H min: 30 H max: 83 kHz, PixClock max 175 MHz
[ 1767.273] (II) NOUVEAU(0): EDID (in hex):
[ 1767.273] (II) NOUVEAU(0): 00ffffffffffff0010ac9aa04c4e5032
[ 1767.273] (II) NOUVEAU(0): 29170104a5351e783aa0a5a656529d27
[ 1767.273] (II) NOUVEAU(0): 0f5054a54b00714f8180a9c0d1c00101
[ 1767.273] (II) NOUVEAU(0): 010101010101023a801871382d40582c
[ 1767.273] (II) NOUVEAU(0): 45000f292100001e000000ff00333657
[ 1767.273] (II) NOUVEAU(0): 4a5833413932504e4c0a000000fc0044
[ 1767.273] (II) NOUVEAU(0): 454c4c205032343134480a20000000fd
[ 1767.273] (II) NOUVEAU(0): 00384c1e5311000a2020202020200053
[ 1767.273] (II) NOUVEAU(0): Printing probed modes for output DP-1
[ 1767.273] (II) NOUVEAU(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[ 1767.273] (II) NOUVEAU(0): Modeline "1600x900"x60.0 118.96 1600 1696 1864 2128 900 901 904 932 -hsync +vsync (55.9 kHz)
[ 1767.273] (II) NOUVEAU(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 1767.273] (II) NOUVEAU(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 1767.273] (II) NOUVEAU(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 1767.273] (II) NOUVEAU(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz e)
[ 1767.273] (II) NOUVEAU(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 1767.273] (II) NOUVEAU(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 1767.273] (II) NOUVEAU(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 1767.273] (II) NOUVEAU(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 1767.273] (II) NOUVEAU(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 1767.273] (II) NOUVEAU(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 1767.273] (II) NOUVEAU(0): Output DVI-I-1 connected
[ 1767.273] (II) NOUVEAU(0): Output DP-1 connected
[ 1767.273] (II) NOUVEAU(0): Using exact sizes for initial modes
[ 1767.273] (II) NOUVEAU(0): Output DVI-I-1 using initial mode 1920x1080
[ 1767.273] (II) NOUVEAU(0): Output DP-1 using initial mode 1920x1080
[ 1767.273] (II) NOUVEAU(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 1767.274] (--) NOUVEAU(0): Virtual size is 1920x1080 (pitch 0)
[ 1767.274] (**) NOUVEAU(0): Driver mode "1920x1080": 148.5 MHz (scaled from 0.0 MHz), 67.5 kHz, 60.0 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[ 1767.274] (**) NOUVEAU(0): Mode "1600x900": 119.0 MHz (scaled from 0.0 MHz), 55.9 kHz, 60.0 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "1600x900"x60.0 118.96 1600 1696 1864 2128 900 901 904 932 -hsync +vsync (55.9 kHz)
[ 1767.274] (**) NOUVEAU(0): Driver mode "1280x1024": 135.0 MHz (scaled from 0.0 MHz), 80.0 kHz, 75.0 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 1767.274] (**) NOUVEAU(0): Driver mode "1280x1024": 108.0 MHz (scaled from 0.0 MHz), 64.0 kHz, 60.0 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 1767.274] (**) NOUVEAU(0): Driver mode "1152x864": 108.0 MHz (scaled from 0.0 MHz), 67.5 kHz, 75.0 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 1767.274] (**) NOUVEAU(0): Driver mode "1024x768": 78.8 MHz (scaled from 0.0 MHz), 60.1 kHz, 75.1 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz e)
[ 1767.274] (**) NOUVEAU(0): Driver mode "1024x768": 65.0 MHz (scaled from 0.0 MHz), 48.4 kHz, 60.0 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 1767.274] (**) NOUVEAU(0): Driver mode "800x600": 49.5 MHz (scaled from 0.0 MHz), 46.9 kHz, 75.0 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 1767.274] (**) NOUVEAU(0): Driver mode "800x600": 40.0 MHz (scaled from 0.0 MHz), 37.9 kHz, 60.3 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 1767.274] (**) NOUVEAU(0): Driver mode "640x480": 31.5 MHz (scaled from 0.0 MHz), 37.5 kHz, 75.0 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 1767.274] (**) NOUVEAU(0): Driver mode "640x480": 25.2 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.0 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 1767.274] (**) NOUVEAU(0): Driver mode "720x400": 28.3 MHz (scaled from 0.0 MHz), 31.5 kHz, 70.1 Hz
[ 1767.274] (II) NOUVEAU(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 1767.274] (==) NOUVEAU(0): DPI set to (96, 96)
[ 1767.274] (II) Loading sub module "fb"
[ 1767.274] (II) LoadModule: "fb"
[ 1767.274] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 1767.274] (II) Module fb: vendor="X.Org Foundation"
[ 1767.274] compiled for 1.14.5, module version = 1.0.0
[ 1767.274] ABI class: X.Org ANSI C Emulation, version 0.4
[ 1767.274] (II) Loading sub module "exa"
[ 1767.274] (II) LoadModule: "exa"
[ 1767.274] (II) Loading /usr/lib/xorg/modules/libexa.so
[ 1767.274] (II) Module exa: vendor="X.Org Foundation"
[ 1767.274] compiled for 1.14.5, module version = 2.6.0
[ 1767.274] ABI class: X.Org Video Driver, version 14.1
[ 1767.274] (II) Loading sub module "shadowfb"
[ 1767.274] (II) LoadModule: "shadowfb"
[ 1767.274] (II) Loading /usr/lib/xorg/modules/libshadowfb.so
[ 1767.274] (II) Module shadowfb: vendor="X.Org Foundation"
[ 1767.274] compiled for 1.14.5, module version = 1.0.0
[ 1767.274] ABI class: X.Org ANSI C Emulation, version 0.4
[ 1767.274] (II) Loading sub module "dri2"
[ 1767.274] (II) LoadModule: "dri2"
[ 1767.274] (II) Module "dri2" already built-in
[ 1767.274] (--) NOUVEAU(G0): Chipset: "NVIDIA NVC1"
[ 1767.275] (==) NOUVEAU(G0): Depth 24, (--) framebuffer bpp 32
[ 1767.275] (==) NOUVEAU(G0): RGB weight 888
[ 1767.275] (==) NOUVEAU(G0): Default visual is TrueColor
[ 1767.275] (==) NOUVEAU(G0): Using HW cursor
[ 1767.275] (==) NOUVEAU(G0): GLX sync to VBlank disabled.
[ 1767.275] (==) NOUVEAU(G0): Page flipping enabled
[ 1767.275] (==) NOUVEAU(G0): Swap limit set to 2 [Max allowed 2]
[ 1767.308] (II) NOUVEAU(G0): Output DVI-I-1-2 has no monitor section
[ 1767.316] (II) NOUVEAU(G0): Output DP-1-2 has no monitor section
[ 1767.339] (II) NOUVEAU(G0): EDID for output DVI-I-1-2
[ 1767.347] (II) NOUVEAU(G0): EDID for output DP-1-2
[ 1767.347] (II) NOUVEAU(G0): Manufacturer: DEL Model: a09a Serial#: 844124236
[ 1767.347] (II) NOUVEAU(G0): Year: 2013 Week: 41
[ 1767.347] (II) NOUVEAU(G0): EDID Version: 1.4
[ 1767.347] (II) NOUVEAU(G0): Digital Display Input
[ 1767.347] (II) NOUVEAU(G0): 8 bits per channel
[ 1767.347] (II) NOUVEAU(G0): Digital interface is DisplayPort
[ 1767.347] (II) NOUVEAU(G0): Max Image Size [cm]: horiz.: 53 vert.: 30
[ 1767.347] (II) NOUVEAU(G0): Gamma: 2.20
[ 1767.347] (II) NOUVEAU(G0): DPMS capabilities: Off
[ 1767.347] (II) NOUVEAU(G0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4 YCrCb 4:2:2
[ 1767.347] (II) NOUVEAU(G0): First detailed timing is preferred mode
[ 1767.347] (II) NOUVEAU(G0): Preferred mode is native pixel format and refresh rate
[ 1767.347] (II) NOUVEAU(G0): redX: 0.650 redY: 0.338 greenX: 0.320 greenY: 0.613
[ 1767.347] (II) NOUVEAU(G0): blueX: 0.154 blueY: 0.061 whiteX: 0.313 whiteY: 0.329
[ 1767.347] (II) NOUVEAU(G0): Supported established timings:
[ 1767.347] (II) NOUVEAU(G0): 720x400@70Hz
[ 1767.347] (II) NOUVEAU(G0): 640x480@60Hz
[ 1767.347] (II) NOUVEAU(G0): 640x480@75Hz
[ 1767.347] (II) NOUVEAU(G0): 800x600@60Hz
[ 1767.347] (II) NOUVEAU(G0): 800x600@75Hz
[ 1767.347] (II) NOUVEAU(G0): 1024x768@60Hz
[ 1767.347] (II) NOUVEAU(G0): 1024x768@75Hz
[ 1767.347] (II) NOUVEAU(G0): 1280x1024@75Hz
[ 1767.348] (II) NOUVEAU(G0): Manufacturer's mask: 0
[ 1767.348] (II) NOUVEAU(G0): Supported standard timings:
[ 1767.348] (II) NOUVEAU(G0): #0: hsize: 1152 vsize 864 refresh: 75 vid: 20337
[ 1767.348] (II) NOUVEAU(G0): #1: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 1767.348] (II) NOUVEAU(G0): #2: hsize: 1600 vsize 900 refresh: 60 vid: 49321
[ 1767.348] (II) NOUVEAU(G0): #3: hsize: 1920 vsize 1080 refresh: 60 vid: 49361
[ 1767.348] (II) NOUVEAU(G0): Supported detailed timing:
[ 1767.348] (II) NOUVEAU(G0): clock: 148.5 MHz Image Size: 527 x 297 mm
[ 1767.348] (II) NOUVEAU(G0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 1767.348] (II) NOUVEAU(G0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 1767.348] (II) NOUVEAU(G0): Serial No: 36WJX3A92PPL
[ 1767.348] (II) NOUVEAU(G0): Monitor name: DELL P2414H
[ 1767.348] (II) NOUVEAU(G0): Ranges: V min: 56 V max: 76 Hz, H min: 30 H max: 83 kHz, PixClock max 175 MHz
[ 1767.348] (II) NOUVEAU(G0): EDID (in hex):
[ 1767.348] (II) NOUVEAU(G0): 00ffffffffffff0010ac9aa04c505032
[ 1767.348] (II) NOUVEAU(G0): 29170104a5351e783aa0a5a656529d27
[ 1767.348] (II) NOUVEAU(G0): 0f5054a54b00714f8180a9c0d1c00101
[ 1767.348] (II) NOUVEAU(G0): 010101010101023a801871382d40582c
[ 1767.348] (II) NOUVEAU(G0): 45000f292100001e000000ff00333657
[ 1767.348] (II) NOUVEAU(G0): 4a583341393250504c0a000000fc0044
[ 1767.348] (II) NOUVEAU(G0): 454c4c205032343134480a20000000fd
[ 1767.348] (II) NOUVEAU(G0): 00384c1e5311000a202020202020004f
[ 1767.348] (II) NOUVEAU(G0): Printing probed modes for output DP-1-2
[ 1767.348] (II) NOUVEAU(G0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[ 1767.348] (II) NOUVEAU(G0): Modeline "1600x900"x60.0 118.96 1600 1696 1864 2128 900 901 904 932 -hsync +vsync (55.9 kHz)
[ 1767.348] (II) NOUVEAU(G0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e)
[ 1767.348] (II) NOUVEAU(G0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 1767.348] (II) NOUVEAU(G0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e)
[ 1767.348] (II) NOUVEAU(G0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz e)
[ 1767.348] (II) NOUVEAU(G0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 1767.348] (II) NOUVEAU(G0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e)
[ 1767.348] (II) NOUVEAU(G0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 1767.348] (II) NOUVEAU(G0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e)
[ 1767.348] (II) NOUVEAU(G0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 1767.348] (II) NOUVEAU(G0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e)
[ 1767.348] (II) NOUVEAU(G0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 1767.348] (--) NOUVEAU(G0): Virtual size is 1024x768 (pitch 0)
[ 1767.348] (**) NOUVEAU(G0): Mode "1920x1080": 173.0 MHz (scaled from 0.0 MHz), 67.2 kHz, 60.0 Hz
[ 1767.348] (II) NOUVEAU(G0): Modeline "1920x1080"x60.0 173.00 1920 2048 2248 2576 1080 1083 1088 1120 -hsync +vsync (67.2 kHz)
[ 1767.348] (==) NOUVEAU(G0): DPI set to (96, 96)
[ 1767.348] (II) Loading sub module "fb"
[ 1767.348] (II) LoadModule: "fb"
[ 1767.348] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 1767.348] (II) Module fb: vendor="X.Org Foundation"
[ 1767.348] compiled for 1.14.5, module version = 1.0.0
[ 1767.348] ABI class: X.Org ANSI C Emulation, version 0.4
[ 1767.348] (II) Loading sub module "exa"
[ 1767.348] (II) LoadModule: "exa"
[ 1767.348] (II) Loading /usr/lib/xorg/modules/libexa.so
[ 1767.348] (II) Module exa: vendor="X.Org Foundation"
[ 1767.348] compiled for 1.14.5, module version = 2.6.0
[ 1767.348] ABI class: X.Org Video Driver, version 14.1
[ 1767.348] (II) Loading sub module "shadowfb"
[ 1767.348] (II) LoadModule: "shadowfb"
[ 1767.348] (II) Loading /usr/lib/xorg/modules/libshadowfb.so
[ 1767.348] (II) Module shadowfb: vendor="X.Org Foundation"
[ 1767.348] compiled for 1.14.5, module version = 1.0.0
[ 1767.348] ABI class: X.Org ANSI C Emulation, version 0.4
[ 1767.348] (--) Depth 24 pixmap format is 32 bpp
[ 1767.351] (II) NOUVEAU(G0): Opened GPU channel 0
[ 1767.359] (II) NOUVEAU(G0): [DRI2] Setup complete
[ 1767.359] (II) NOUVEAU(G0): [DRI2] DRI driver: nouveau
[ 1767.359] (II) NOUVEAU(G0): [DRI2] VDPAU driver: nouveau
[ 1767.360] (II) EXA(256): Driver allocated offscreen pixmaps
[ 1767.360] (II) EXA(256): Driver registered support for the following operations:
[ 1767.360] (II) Solid
[ 1767.360] (II) Copy
[ 1767.360] (II) Composite (RENDER acceleration)
[ 1767.360] (II) UploadToScreen
[ 1767.360] (II) DownloadFromScreen
[ 1767.360] (==) NOUVEAU(G0): Backing store disabled
[ 1767.360] (==) NOUVEAU(G0): Silken mouse enabled
[ 1767.360] (II) NOUVEAU(G0): [XvMC] Associated with Nouveau GeForce 8/9 Textured Video.
[ 1767.360] (II) NOUVEAU(G0): [XvMC] Extension initialized.
[ 1767.360] (==) NOUVEAU(G0): DPMS enabled
[ 1767.360] (II) NOUVEAU(G0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 1767.360] (WW) NOUVEAU(G0): Option "Monitor-DVI-I-1" is not used
[ 1767.360] (WW) NOUVEAU(G0): Option "Monitor-DP-1" is not used
[ 1767.362] (II) NOUVEAU(0): Opened GPU channel 0
[ 1767.366] (II) NOUVEAU(0): [DRI2] Setup complete
[ 1767.366] (II) NOUVEAU(0): [DRI2] DRI driver: nouveau
[ 1767.366] (II) NOUVEAU(0): [DRI2] VDPAU driver: nouveau
[ 1767.366] (II) EXA(0): Driver allocated offscreen pixmaps
[ 1767.366] (II) EXA(0): Driver registered support for the following operations:
[ 1767.366] (II) Solid
[ 1767.366] (II) Copy
[ 1767.366] (II) Composite (RENDER acceleration)
[ 1767.366] (II) UploadToScreen
[ 1767.366] (II) DownloadFromScreen
[ 1767.366] (==) NOUVEAU(0): Backing store disabled
[ 1767.366] (==) NOUVEAU(0): Silken mouse enabled
[ 1767.366] (II) NOUVEAU(0): [XvMC] Associated with Nouveau GeForce 8/9 Textured Video.
[ 1767.366] (II) NOUVEAU(0): [XvMC] Extension initialized.
[ 1767.366] (==) NOUVEAU(0): DPMS enabled
[ 1767.366] (II) NOUVEAU(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 1767.366] (--) RandR disabled
[ 1767.388] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 1767.388] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 1767.388] (II) AIGLX: enabled GLX_ARB_create_context
[ 1767.388] (II) AIGLX: enabled GLX_ARB_create_context_profile
[ 1767.388] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile
[ 1767.388] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 1767.388] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 1767.389] (II) AIGLX: Loaded and initialized nouveau
[ 1767.389] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 1767.390] (II) NOUVEAU(G0): NVEnterVT is called.
[ 1767.393] (II) NOUVEAU(0): NVEnterVT is called.
[ 1767.444] (II) NOUVEAU(0): Setting screen physical size to 508 x 285
[ 1767.444] resize called 1920 1080
[ 1767.479] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[ 1767.479] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 1767.479] (II) LoadModule: "evdev"
[ 1767.479] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 1767.479] (II) Module evdev: vendor="X.Org Foundation"
[ 1767.479] compiled for 1.14.3, module version = 2.8.2
[ 1767.479] Module class: X.Org XInput Driver
[ 1767.479] ABI class: X.Org XInput driver, version 19.1
[ 1767.479] (II) Using input driver 'evdev' for 'Power Button'
[ 1767.479] (**) Power Button: always reports core events
[ 1767.479] (**) evdev: Power Button: Device: "/dev/input/event2"
[ 1767.479] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 1767.479] (--) evdev: Power Button: Found keys
[ 1767.479] (II) evdev: Power Button: Configuring as keyboard
[ 1767.479] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3/event2"
[ 1767.479] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 1767.479] (**) Option "xkb_rules" "evdev"
[ 1767.479] (**) Option "xkb_model" "pc104"
[ 1767.479] (**) Option "xkb_layout" "us"
[ 1767.499] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[ 1767.499] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 1767.499] (II) Using input driver 'evdev' for 'Power Button'
[ 1767.500] (**) Power Button: always reports core events
[ 1767.500] (**) evdev: Power Button: Device: "/dev/input/event1"
[ 1767.500] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 1767.500] (--) evdev: Power Button: Found keys
[ 1767.500] (II) evdev: Power Button: Configuring as keyboard
[ 1767.500] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2/event1"
[ 1767.500] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[ 1767.500] (**) Option "xkb_rules" "evdev"
[ 1767.500] (**) Option "xkb_model" "pc104"
[ 1767.500] (**) Option "xkb_layout" "us"
[ 1767.500] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 1767.500] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=3 (/dev/input/event14)
[ 1767.500] (II) No input driver specified, ignoring this device.
[ 1767.500] (II) This device may have been added with another device file.
[ 1767.500] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=7 (/dev/input/event13)
[ 1767.500] (II) No input driver specified, ignoring this device.
[ 1767.500] (II) This device may have been added with another device file.
[ 1767.500] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=8 (/dev/input/event12)
[ 1767.501] (II) No input driver specified, ignoring this device.
[ 1767.501] (II) This device may have been added with another device file.
[ 1767.501] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=9 (/dev/input/event11)
[ 1767.501] (II) No input driver specified, ignoring this device.
[ 1767.501] (II) This device may have been added with another device file.
[ 1767.501] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event6)
[ 1767.501] (II) No input driver specified, ignoring this device.
[ 1767.501] (II) This device may have been added with another device file.
[ 1767.501] (II) config/udev: Adding input device HDA Intel PCH Front Mic (/dev/input/event9)
[ 1767.501] (II) No input driver specified, ignoring this device.
[ 1767.501] (II) This device may have been added with another device file.
[ 1767.501] (II) config/udev: Adding input device HDA Intel PCH Line Out (/dev/input/event8)
[ 1767.501] (II) No input driver specified, ignoring this device.
[ 1767.501] (II) This device may have been added with another device file.
[ 1767.501] (II) config/udev: Adding input device HDA Intel PCH Front Headphone (/dev/input/event7)
[ 1767.501] (II) No input driver specified, ignoring this device.
[ 1767.501] (II) This device may have been added with another device file.
[ 1767.502] (II) config/udev: Adding input device HDA Intel PCH Rear Mic (/dev/input/event10)
[ 1767.502] (II) No input driver specified, ignoring this device.
[ 1767.502] (II) This device may have been added with another device file.
[ 1767.502] (II) config/udev: Adding input device DELL Dell USB Entry Keyboard (/dev/input/event4)
[ 1767.502] (**) DELL Dell USB Entry Keyboard: Applying InputClass "evdev keyboard catchall"
[ 1767.502] (II) Using input driver 'evdev' for 'DELL Dell USB Entry Keyboard'
[ 1767.502] (**) DELL Dell USB Entry Keyboard: always reports core events
[ 1767.502] (**) evdev: DELL Dell USB Entry Keyboard: Device: "/dev/input/event4"
[ 1767.502] (--) evdev: DELL Dell USB Entry Keyboard: Vendor 0x413c Product 0x2107
[ 1767.502] (--) evdev: DELL Dell USB Entry Keyboard: Found keys
[ 1767.502] (II) evdev: DELL Dell USB Entry Keyboard: Configuring as keyboard
[ 1767.502] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.5/4-1.5:1.0/input/input5/event4"
[ 1767.502] (II) XINPUT: Adding extended input device "DELL Dell USB Entry Keyboard" (type: KEYBOARD, id 8)
[ 1767.502] (**) Option "xkb_rules" "evdev"
[ 1767.502] (**) Option "xkb_model" "pc104"
[ 1767.502] (**) Option "xkb_layout" "us"
[ 1767.502] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/event5)
[ 1767.502] (**) Logitech USB Optical Mouse: Applying InputClass "evdev pointer catchall"
[ 1767.502] (II) Using input driver 'evdev' for 'Logitech USB Optical Mouse'
[ 1767.502] (**) Logitech USB Optical Mouse: always reports core events
[ 1767.502] (**) evdev: Logitech USB Optical Mouse: Device: "/dev/input/event5"
[ 1767.502] (--) evdev: Logitech USB Optical Mouse: Vendor 0x46d Product 0xc077
[ 1767.502] (--) evdev: Logitech USB Optical Mouse: Found 12 mouse buttons
[ 1767.502] (--) evdev: Logitech USB Optical Mouse: Found scroll wheel(s)
[ 1767.502] (--) evdev: Logitech USB Optical Mouse: Found relative axes
[ 1767.502] (--) evdev: Logitech USB Optical Mouse: Found x and y relative axes
[ 1767.502] (II) evdev: Logitech USB Optical Mouse: Configuring as mouse
[ 1767.502] (II) evdev: Logitech USB Optical Mouse: Adding scrollwheel support
[ 1767.503] (**) evdev: Logitech USB Optical Mouse: YAxisMapping: buttons 4 and 5
[ 1767.503] (**) evdev: Logitech USB Optical Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 1767.503] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.6/4-1.6:1.0/input/input6/event5"
[ 1767.503] (II) XINPUT: Adding extended input device "Logitech USB Optical Mouse" (type: MOUSE, id 9)
[ 1767.503] (II) evdev: Logitech USB Optical Mouse: initialized for relative axes.
[ 1767.503] (**) Logitech USB Optical Mouse: (accel) keeping acceleration scheme 1
[ 1767.503] (**) Logitech USB Optical Mouse: (accel) acceleration profile 0
[ 1767.503] (**) Logitech USB Optical Mouse: (accel) acceleration factor: 2.000
[ 1767.503] (**) Logitech USB Optical Mouse: (accel) acceleration threshold: 4
[ 1767.503] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/mouse0)
[ 1767.503] (II) No input driver specified, ignoring this device.
[ 1767.503] (II) This device may have been added with another device file.
[ 1767.503] (II) config/udev: Adding drm device (/dev/dri/card1)
[ 1767.503] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=3 (/dev/input/event18)
[ 1767.503] (II) No input driver specified, ignoring this device.
[ 1767.503] (II) This device may have been added with another device file.
[ 1767.504] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=7 (/dev/input/event17)
[ 1767.504] (II) No input driver specified, ignoring this device.
[ 1767.504] (II) This device may have been added with another device file.
[ 1767.504] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=8 (/dev/input/event16)
[ 1767.504] (II) No input driver specified, ignoring this device.
[ 1767.504] (II) This device may have been added with another device file.
[ 1767.504] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=9 (/dev/input/event15)
[ 1767.504] (II) No input driver specified, ignoring this device.
[ 1767.504] (II) This device may have been added with another device file.
[ 1767.504] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 1767.504] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 1767.504] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 1767.504] (**) AT Translated Set 2 keyboard: always reports core events
[ 1767.504] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 1767.504] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[ 1767.504] (--) evdev: AT Translated Set 2 keyboard: Found keys
[ 1767.504] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[ 1767.504] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 1767.504] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 10)
[ 1767.504] (**) Option "xkb_rules" "evdev"
[ 1767.504] (**) Option "xkb_model" "pc104"
[ 1767.504] (**) Option "xkb_layout" "us"
[ 1767.505] (II) config/udev: Adding input device PS/2 Generic Mouse (/dev/input/event19)
[ 1767.505] (**) PS/2 Generic Mouse: Applying InputClass "evdev pointer catchall"
[ 1767.505] (II) Using input driver 'evdev' for 'PS/2 Generic Mouse'
[ 1767.505] (**) PS/2 Generic Mouse: always reports core events
[ 1767.505] (**) evdev: PS/2 Generic Mouse: Device: "/dev/input/event19"
[ 1767.505] (--) evdev: PS/2 Generic Mouse: Vendor 0x2 Product 0x1
[ 1767.505] (--) evdev: PS/2 Generic Mouse: Found 3 mouse buttons
[ 1767.505] (--) evdev: PS/2 Generic Mouse: Found relative axes
[ 1767.505] (--) evdev: PS/2 Generic Mouse: Found x and y relative axes
[ 1767.505] (II) evdev: PS/2 Generic Mouse: Configuring as mouse
[ 1767.505] (**) evdev: PS/2 Generic Mouse: YAxisMapping: buttons 4 and 5
[ 1767.505] (**) evdev: PS/2 Generic Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 1767.505] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input7/event19"
[ 1767.505] (II) XINPUT: Adding extended input device "PS/2 Generic Mouse" (type: MOUSE, id 11)
[ 1767.505] (II) evdev: PS/2 Generic Mouse: initialized for relative axes.
[ 1767.505] (**) PS/2 Generic Mouse: (accel) keeping acceleration scheme 1
[ 1767.505] (**) PS/2 Generic Mouse: (accel) acceleration profile 0
[ 1767.505] (**) PS/2 Generic Mouse: (accel) acceleration factor: 2.000
[ 1767.505] (**) PS/2 Generic Mouse: (accel) acceleration threshold: 4
[ 1767.505] (II) config/udev: Adding input device PS/2 Generic Mouse (/dev/input/mouse1)
[ 1767.505] (II) No input driver specified, ignoring this device.
[ 1767.505] (II) This device may have been added with another device file.
[ 1767.505] (II) config/udev: Adding input device PC Speaker (/dev/input/event3)
[ 1767.505] (II) No input driver specified, ignoring this device.
[ 1767.505] (II) This device may have been added with another device file.
[ 1774.230] (II) AIGLX: Suspending AIGLX clients for VT switch
[ 1774.230] (II) NOUVEAU(0): NVLeaveVT is called.
[ 1774.230] (II) NOUVEAU(G0): NVLeaveVT is called.
[ 1779.499] (II) evdev: PS/2 Generic Mouse: Close
[ 1779.499] (II) UnloadModule: "evdev"
[ 1779.499] (II) evdev: AT Translated Set 2 keyboard: Close
[ 1779.499] (II) UnloadModule: "evdev"
[ 1779.499] (II) evdev: Logitech USB Optical Mouse: Close
[ 1779.499] (II) UnloadModule: "evdev"
[ 1779.499] (II) evdev: DELL Dell USB Entry Keyboard: Close
[ 1779.499] (II) UnloadModule: "evdev"
[ 1779.499] (II) evdev: Power Button: Close
[ 1779.499] (II) UnloadModule: "evdev"
[ 1779.499] (II) evdev: Power Button: Close
[ 1779.499] (II) UnloadModule: "evdev"
[ 1779.499] (II) NOUVEAU(G0): NVLeaveVT is called.
[ 1780.500] Error dropping master: -22(Invalid argument)
[ 1780.501] (II) NOUVEAU(G0): Closed GPU channel 0
[ 1780.503] (II) NOUVEAU(0): Closed GPU channel 0
[ 1780.503] (EE) Server terminated successfully (0). Closing log file.
Thanks for any help!I have a similar issue except with two ATI cards and four monitors.
I have a working xorg.conf that uses Xinerama and all 4 work but have been trying to get xrandr to work since xinerama is deprecated supposedly.
I would like to switch to xrandr but there is some kind of magic voodoo I have with my current xorg.conf that doesn't even work on an exact same machine and cards that I tried to setup for a co-worker.
lspci:
01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV610 [Radeon HD 2400 PRO/XT]
04:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV610 [Radeon HD 2400 PRO/XT]
My xorg.conf:
Section "Device"
Identifier "ATI0"
Driver "radeon"
BusID "PCI:1:0:0"
Option "ZaphodHeads" "DVI-0"
Screen 0
EndSection
Section "Device"
Identifier "ATI1"
Driver "radeon"
BusID "PCI:1:0:0"
Option "ZaphodHeads" "DVI-1"
Screen 1
EndSection
Section "Device"
Identifier "ATI2"
Driver "radeon"
BusID "PCI:4:0:0"
Option "ZaphodHeads" "DVI-2"
Screen 0
EndSection
Section "Device"
Identifier "ATI3"
Driver "radeon"
BusID "PCI:4:0:0"
Option "ZaphodHeads" "DVI-3"
Screen 1
EndSection
Section "Monitor"
Identifier "DVI-0"
Option "Primary" "On"
Option "DPMS" "true"
Option "PreferredMode" "1920x1080"
Option "TargetRefresh" "60"
EndSection
Section "Monitor"
Identifier "DVI-1"
Option "DPMS" "true"
Option "PreferredMode" "1920x1080"
Option "TargetRefresh" "60"
EndSection
Section "Monitor"
Identifier "DVI-2"
Option "DPMS" "true"
Option "PreferredMode" "1920x1080"
Option "TargetRefresh" "60"
EndSection
Section "Monitor"
Identifier "DVI-3"
Option "DPMS" "true"
Option "PreferredMode" "1920x1080"
Option "TargetRefresh" "60"
EndSection
Section "Screen"
Identifier "Screen0"
Device "ATI0"
Monitor "DVI-0"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1920x1080"
EndSubSection
EndSection
Section "Screen"
Identifier "Screen1"
Device "ATI1"
Monitor "DVI-1"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1920x1080"
EndSubSection
EndSection
Section "Screen"
Identifier "Screen2"
Device "ATI2"
Monitor "DVI-2"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1920x1080"
EndSubSection
EndSection
Section "Screen"
Identifier "Screen3"
Device "ATI3"
Monitor "DVI-3"
DefaultDepth 24
Subsection "Display"
Depth 24
Modes "1920x1080"
EndSubSection
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Emulate3Buttons" "no"
Option "ZAxisMapping" "4 5"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "ServerLayout"
Identifier "Default Layout"
Screen "Screen0" 0 0
Screen "Screen1" RightOf "Screen0"
Screen "Screen2" Above "Screen1"
Screen "Screen3" Above "Screen0"
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
Option "Xinerama" "1"
EndSection
My Xorg.0.log shows all the DVI connections when I don't use a xorg.conf file but only two are "connected"
I see DVI-0 and DVI-1 connected and in "xrandr -q" but in Xorg.0.log I see DVI-1-2 and DVI-1-3.
xrandr --listproviders show the two cards as well.
Tried "xrandr --setprovideroutputsource 1 0" and they show up in KDE but as clones and then X crashes eventually.
"xrandr --setprovideroutputsource 0 1" just plain crashes X
Maybe you are looking for
-
How to add class file to the project in netbean
Hi, I am not sure if it is the right place to put the question. I just cannot find the way to add my existing java class file into the project in net bean. Anyone can help? Thanks a lot
-
Free of Charge indicator in Purchase Order / Line item
Dear All, Is there a table where i could locate if a particular purchase order / line item has the FOC tick maintained. I went through quite a few tables and am unable to locate the same. Or is there any other logic from which i could derive if a par
-
Trigger Second Interface for the same Creation event
Hello all, I have to send my every created equipment to two different systems. I created Custom function Modules which create individual Idocs. I called these function modules in Methods and we created two custom Tasks to trigger workflow creation ev
-
Why a method can not be invoked in JSP ???
I define a method in a JAVA Class file,as this: public Enumeration getElementsNamed(String name, String parentname) { Element elem = doc.getDocumentElement(); NodeList nodes = elem.getElementsByTagName(name); int size = nodes.getLength(); Vector elem
-
Expression editor: generic function GET
Hi there, I want to send an e-mail, that contains context data with cardinatlity 1..n. My context looks like this: |- Data Object (1..1) |---STATUS (1..n) |----- ApprovedBy (0..1) |----- ApprovedOn (0..1) |----- DeclinedBy (0..1) |----- DeclinedOn (0