Al realizar un ejecutable me marca un error en labview 2009

Saludos
El error es el siguiente, porfavor ayuda
Visit the Request Support page at ni.com/ask to learn more about resolving this problem. Use the following information as a reference:
Error 5 occurred at Delete in New Zip File.vi->AB_Engine_Package_App.vi->AB_EXE.lvclass:Build.vi->AB_Build.lvclass:Build_from_Wizard.vi->AB_UI_Frmwk_Build.lvclass:Build.vi->AB_UI_FRAMEWORK.vi->AB_Create_Build_Application.vi->EBUIP_Global_OnCommand.vi->EBUIP_Global_OnCommand.vi.ProxyCaller
Possible reason(s):
LabVIEW: File already open.
C:\Documents and Settings\fernando.garcia\Desktop\builds\registro2\registro\Application.zip

Verify that the file is located there first.
Make sure that it is not open by some other program
Make sure that you do not have any references to it in LabVIEW except where you are trying to use it.
Make sure that it is not read only.
Tim
Johnson Controls
Holland Michigan

Similar Messages

TS3694 mi ipod touch 4g marca un error al intentar restaurar de fabrica. es el error (3194) podrian ayudarme?

no pueedo restaurar mi ipod touch 4g. me marca el error (3194) podrian ayudarme??

See the actions for that error here:
iTunes: Specific update-and-restore error messages and advanced troubleshooting
iPhone Error 3194 - How to Fix iTunes Error 3194?
Fix Error 3194 from iTunes during iPhone restore

Me marca un error al abrir iTunes

Buen día
Me marca un error al abrir iTunes algo de que lo tengo privilegio para abrir el programa...

Gracias, ya pude eliminar el archivo sc y ya no manda error el itunes, agradezco el apoyo y envio imagen de donde se encuentra el archivo en windows 8, saludos
Message was edited by: Pedroandrese

Porque al descargar Creativeclound me marca el error 205¿?

trato de instalar este programa pero el instalador no llega ni a la mitad y me marca el error 205

error 21 http://support.apple.com/kb/TS3694
error 42110 http://support.apple.com/kb/TS1424

Realizar un Ejecutable

Buenos días a todos.
estoy realizando una aplicacion en labview 8.5,
y quiero realizar un ejecutable, alguien me puede
indicar cono hacerlo.
gracias

Foro Repetido
http://forums.ni.com/ni/board/message?board.id=6170&thread.id=5229
Carlos Pazos
Applications Engineer
National Instruments Mexico

Ejecutable Labview 2009

Hola no poseo el Aplication Builder de labVIEW 2009, hace poco ya me crearon un ejecutable pero tube unos problemas y tube que realizar unas modificaciones. Alguien sería tan amable de crearme un ejecutable del programa que adjunto?
Muchas gracias.
Attachments:
Nueva logica proyecto 5 REV.vi ‏36 KB

Hola,
Primero, para poder realizar ejecutable y instaladores tienes que tener LabVIEW PDS (Professional Development System) o FDS (Full Development System) ; si tienes LabVIEW Base no podrás.
Luego, lo que tienes que hacer :
- en el LabVIEW proyecto, abajo hay "Build Specification", allí tienes que añadir un EXE y abrelo para definir sus propriedades.
- cuando este ejecutable funciona en tu ordenador tendrás que realizar un instalador si quieres que funcione en otro ordenador que no tiene LabVIEW.
Suerte
When my feet touch the ground each morning the devil thinks "bloody hell... He's up again!"

Error in ni visa control out for usb in labview 2009

Hi,
I am using labview 2009 in which i have made a vi which communicates with a pic controller through USB interface.
the vi is working fine in labview 8.6. I tried it in two PCs. but when i run that vi in a PC with labview 2009 then the VISA CONTROL OUT.vi gives error "0xBFFF003E : Could not perform operation because of i o error.". while the control in.vi works fine in both the labview versions and any other PC that i tried.
I have run the application in total of 4 PCs with same set of cards/interfaces. two of them having labview 8.6 are running fine and giving no error but other two with labview 2009 are giving error.
and it doesn't stop here.... i searched in the vi and did some experiment and found that when i give Request value input to control out.vi as "0x36 "(as required by my PIC program) then it is giving error but when i give other value such as " 0x35 or 34 or 55"(used for other purpose) then it is not giving error.
Can it be a PIC programming problem? (i dont think so as everything is fine in other PC with LV 8.6)
I have already explored the ni forum for this error solution but could not find helpful.
Can anyone solve my problem?

I installed labview 8.6 in that machine and made a small program with only 3 vis (visa open session, visa close session and visa usb control out.vi) which is working in LV 8.6 platform.
Sorry the above statement is not correct actually.
When i run the program in LV 8.6 it giving that same error but this time it is not displayed as pop up window. so i could not judge that error was still there.

Posting only posisble error in periods 2009/08 and 2009/07 in company code

Hi Experts,
When my user do GI for this month he got error as mentioned below,
Posting only possible error in periods 2009/08 and 2009/07 in company code
Already i have done it but still am not confident.
Also this particular corrections i need to do it in Production system
Please guide which month i need to enter 1st in MMPV,request you to explain step by step.
Cheers,
Kumar.S

Hi,
Check in T.code: MMRV and see which period is open for ur Co.Code and back posting is allowed or not.
In MMPV open period 09 with your company code.
Note-1: Check Fiscal Period Variant in OBY6..........is it K4.
Note-2: From FI side check or Now use t.code: OB52 and open the 09, 2009 period in Account Types A, K, D,M, S and specially Account Type u201C+u201D which stands for valid for all accounts type and save. Better consult FICO consultant for OB52 step.
Regards,
Biju K

LabVIEW 2009 launches with errors

Hi Folks,
LabVIEW 2009 launches with errors now everytime I open it. A window appears showing an error list with nothing in it, with a close and show dialog box (hangs with hour glass). Neither option is possible since the window self closes in about two minutes. It's a little frustrating since it adds to my loading time everytime I launch it.
Any suggestions other than unistall/install process?
Windows XP Professional 2002, SP3
Labview 2009, Mem Alloc 39125K, TCP Server inactive, Version 9.0 (32bit)
Regards,
-SS

Hi!
The exact sme thing happend to me. But for me it was on the LV2010 version. Just suddenly it started to launch everytime I opened LV. After a re-installation of LV it was gone.
Regards,
Even
Certified LabVIEW Associate Developer
Automated Test Developer
Topro AS
Norway

Excecutable VI generating an error 222 on Keithley 2612A although its run properly when starting from labview 2009 directly

Dear all,
I have a VI which runs perfectly and I can control, a Keithley 2612A for transistor measurements.
The VI run well when I excecute it from the computer which has the platform Labview 2009 (XP OS)
The equipment (ie Keithley 2612A) is linked to another computer which don't have labview 2009.
I installed Run-time-engine 2009 (OS XP 32 bits) on this computer.
Then I create an excecutable of my VI with the "build application" option.
The excecutable VI starts normally on the computer but when I want to run it, I am getting an error message from the Keithley 2612A (which was not the case when I ran the VI directly from the computer haing Labview 2009 installed on it). The error message is 222 (ie parameter too long)
I thought that I did something wrong and I create an excecutable from an original VI from Keithley (ie without any change). I am getting the same error message.
When I create an excecutable with run time engine 2009 included (as it is possible to do it wiht LB 2009) , I am geeting the same error message.
So I need no to check step after step when the message happens but
Does anyone knows anything about such an issue ?
Thank you
Solved!
Go to Solution.

Dear all,
Just for those who might encounter a similar issue.
I found the solution after tackling all possibilities.
The source of the problem was (for unknown reason) that the country setting of the computer was wrong
and decimal numbers were written with a , instead of a point.
Since I reset correctly the country setting, the stand alone files are running normally.
Best regards
Youki

Error installing LabVIEW 2011 on Win 7

I'm getting an error installing LabVIEW 2011 Professional:
I found a thread concerning missing MSIs, which suggested that one run setup.exe with the /log function, so I did, but I don't think it actually says anything useful.
I also found a Microsoft download page for WindowsInstaller-KB893803-v2-x86.exe, which is the thing that's supposed to be missing. This seems to be an old version of the installer (most recent compatible OS = WinXP SP2), so I don't really feel like installing this on my Windows 7 system.
Help!! Thanks in advance.
-- Philip

Hi Keller,
I'm Jamie an Applications Engineer at NI UK.
It does seem that you are missing some of the necessary support files required for the installer to run correctly, the details of which are available in the KnowledgeBase article here. Did you download the install files or are you installing from disk?
In addition to the setup.exe file, ensure that you have copied the following folders to the target PC or destination folder when creating an installer with LabVIEW.
bin
license
supportfiles
Hope this helps get you up and running with LabVIEW 2011, let me know if you experience any further issues.
Thanks
Jamie
Jamie S.
Applications Engineer
National Instruments

Run-time error "5010": Labview: VI execution ...

I get Run-time error "5010": Labview: VI execution terminated by server. This error occurs sporatically. I am running Visual Basic 5.0 application that communicates to Labview 6.1 VIs. It is using NI-Imaq to do vision analysis of parts. I just need to know what to look for that may be causing this error. I am also running it on a PXI system with 64 MB of memory.

Hello,
I recommend you to do direct function calls to NI-IMAQ and NI Vision function libraries from Visual Basic as this will be a lot more efficient and improve rubustness of your application. During the installation of both software, you have the option to include support files for Visal Basic. Once these components are installed you should see the shipping examples in the following directories (if installed in the default path):
(NI-IMAQ) C:\Program Files\National Instruments\NI-IMAQ\Sample\VB
(NI Vision) C:\Program Files\National Instruments\MeasurementStudio\VB\Samples\IMAQ
There are additional examples that can be found in the Code Library (see the link on the left sidebar).
Let me know if you have further questions regarding this issue.
Regards,
Yusuf C.
Applications Engineering
National Instruments

Error when trying to set up OPC I/O server with LabView 2009

Hi.I get an error when I try to set up OPC I/O server with LabView 2009 and the DSC module. If I open an empty project, right click ”My Computer”. Select new / I/O Server… and then OPC Client, the following error appears: Unable to browse OPC Server from the selected machine.Error -2147467262 occurred at GetOPCServerList.viPossible reason(s):LabVIEW: (Hex 0x80004002) No such interface supported. I have tried to repair LabView, but with no luck. Any idea what it could be?

The problems are not related to each otherOk then. Lets try getting this solved. Lemme dig......

Why does labview 2009 32-bit closes up with no error message?

Hello.
I am developing an application using a PCI-6534 board, Windows XP SP3, and LabVIEW 2009 32-bits. In this application I am generating a 300 Hz signal using the P2.0 digital line. I am trying to make digital acquisition using the P0 port (8 bits), using N-sampling. The program that generates the 300 Hz clock, works with no problem. However, when I start running the program that performs the data acquisition, LabVIEW suddenly closes up with no error message. The LabVIEW windows just disappear from the screen.
As for me it looks like a LabVIEW bug.
In case anyone decided to help me, I could attach the programs so that you could check them.
What can I do to solve this problem?
Thank you.

I had the same problem with one of our applications. I supplied gigabytes of process monitor and desktop execution toolkit logs, but nothing was resolved. I upgraded from WS2003 and LV2009sp1 to W7 64b and LV2010, per NI's recommendation but the problem persists. I had the corresponding service ticket open for 3 months where NI said the application ran fine for them on W7 with 2010. (long story)
I understand your frustration, and I recommend getting your local application engineer involved as an advocate with application support.. If you pay for service, pound on them to provide it. My $0.02.

Labview 2009 Student Edition Vista x64 installation fail, no error messages though

I am trying to install a copy of the LabView 2009 student edition and everytime the installation initializes, the modules fail to install for every single module. There is also no error message.
I got a message that LabView may not be working correctly due to Windows Firewall, which I have disabled. That message referred me to ni.com/info, code expm69.
Let me know, I'm a little confused as to what's going on. Would it be due to a patch or what not?
Thanks!
Solved!
Go to Solution.

Hi imagineerme,
Regarding your installation issues, a possible cause may be that you don't have permissions on the computer that you are installing. Are you set as the administrator on this computer? Is this a school computer or your own?
It's also possible that LabVIEW may be installed on your computer already. To check this, go to Program Files/National Instruments to see what you already have installed.
If neither of these are the cause, can you please provide me with more information about your installation? Does the installer crash or just go straight to the finish screen? Does anything install at all? Thanks and best of luck,
Julianne K
Julianne K
Systems Engineer, Embedded Systems
Certified LabVIEW Architect, Certified LabVIEW Embedded Systems Developer
National Instruments

Al realizar un ejecutable me marca un error en labview 2009

Similar Messages

Maybe you are looking for