ALE error - variant LOGSYS does not exist?
In trying to setup ALE within SAP (ECC 5.0) to send a material master IDOC from the ERP to XI. I followed the ALE Quick Start guide and several other resources on the net including IDOC Cookbook and others. When I try to select transaction BD10 (Send Material Master), it returns the following error:
Variant LOGSYS does not exist
The long text is:
Variant LOGSYS does not exist
Message no. DB612
Diagnosis
You selected variant LOGSYS for program RBDSEMAT.
This variant does not exist.
Procedure
Correct the entry.
In trying to narrow down the problem, I created a minimal scenario of just sending the MATMAS IDOC from one client to another on the same system and I get the same error.
My first thought was the logical systems for the two
clients were not setup correctly, but they seem okay. I'm using the 'PRODUCTION' logical system that came with the IDES version we installed (client 811) and trying to send to a new client I setup as logical system VM1CLNT300 (client 300) on the same system.
RFC Destinations test okay, partner profiles, ports, and the distribution model seem okay.
Googling for that error message above produced nothing that I could get an answer from. Any ideas?
Thanks,
-tim
Yes, both logical systems are there. Additionally, each
client has been set to the appropriate logical system:
client 811 -> PRODUCTION logical system
client 300 -> VM1CLNT300 logical system
-tim
Similar Messages
-
DP Mass Processing error Variant &0000000000322 does not exist
Hi,
When I double click on the process chain which is created already in transaction RSPC, the system displays message Variant &0000000000322 does not exist.
Please help to resolve this issue.
thanks and regards
MurugesanHi,
Variants starting with & are temporary variants and are not transported from one system to another. So if you have transported your process chain from one system to another, the chances are the temporary variants have not been transported.
So pls change your process chain to use a more permanent variant. You can create permanent variants for mass processing jobs as follows.
Go to SE38, type program name as /sapapo/ts_batch_run. Click on variants and create variants with the relevant info.
Hope this helps.
Thanks
Mani Suresh -
Error - Variant &0000000000000 does not exist in Job Logs
Hi All,
We have job SWWDHEX running under two different Ids at exactly same time and similar varaint in SAP system:
Job CreatedB Status Start date Start time
SWWDHEX BASISBATCH Canceled 12/13/2011 13:32:07
SWWDHEX BASISBATCH Canceled 12/13/2011 13:35:07
SWWDHEX BASISBATCH Canceled 12/13/2011 13:38:07
SWWDHEX BASISBATCH Canceled 12/13/2011 13:41:07
SWWDHEX WF-BATCH Finished 12/13/2011 13:32:07
SWWDHEX WF-BATCH Finished 12/13/2011 13:35:07
SWWDHEX WF-BATCH Finished 12/13/2011 13:38:07
SWWDHEX WF-BATCH Finished 12/13/2011 13:41:07
As you see jobs running Jobs running successfully under User WF-BATCH.
But while BASISBATCH User jobs are failing with error:
u201CVariant &0000000000000 does not existu201D
I checked in jobs which are in released status for both user contains same varaint &0000000000000.
These jobs are running in different clients.
Please let me know reason of this job failure and also let me know is this job client dependent to make sure both runs are necessery for this job.
Regards,
Shivam MittalHello,
As you see jobs running Jobs running successfully under User WF-BATCH.
But while BASISBATCH User jobs are failing with error:
u201CVariant &0000000000000 does not existu201D
This might be related to the fact that it is executed at the same time.
Is it possible to postpone the job in one client by one minute?
Please let me know reason of this job failure and also let me know is this job client dependent to make sure both runs are necessery for this job.
According to available SAP notes this job seems to be client dependent.
Related SAP notes:
Note 1262519 - Functions and monitoring of deadline monitoring
Note 1059852 - Workflow background jobs are scheduled several times
Tomas -
Hi,
When i try to process account statement through FB12 it take me fine but once i go to F.64 and click on the generated request it shoots following error
Variant SAP06 does not exist
Message no. DB612
Diagnosis
You selected variant SAP06 for program RFKORD10.
This variant does not exist.
Procedure
Correct the entry.
Please advise if i am missing anything in configuration.
Thanks!
Mohammed ZiaHi ZIA,
for correspondence variant needs to be assigned to program.
Goto SA38 enter RFKORD10. then maintain variant. click save and rerun f.64.
let me know if you have any problem.
Pls assign points as way to say thanks -
ERROR SHOWS 'VARIANT CASHDE DOES NOT EXIST' WHILE GIVING PRINT in tcod FBCJ
DEAR ALL,
MY FI CONSULTANT WHILE PRESSING PRINT BUTTON IN FBCJ TCODE FOR CASH JOURNAL AN ERROR MESSAGE SHOWS 'VARIANT CASHDE DOES NOT EXIST '. AS AN ABAPER I TRIED A LOT AND DEBUG THE STD. PROGRAM BUT I AM UNABLE TO SOLVE THE ISSUE. SO I NEED UR HELP .PLEASE SUGGEST ME TO SOLVE THE ISSUE.
IT IS VERY URGENT.
REGARDS
BANAJAThanks
-
Transporting Process Chain - error Source system does not exist
Hi,
I tried to transport a local PC by itself (not including its main meta chain) since I have only done modifications in the local PC only. In the PC, there are PSA Processing, ODS Processing, ODS Activation, ABAP Program w/ variants and Infocube Rollup.
However, I got the following transport error: Source system does not exist
=======
Diagnosis
Source system is not known.
System Response
The imported data for DataSource was deleted again because the referenced source system does not exist and no mapping is defined in table RSLOGSYSMAP on an existing productive source system.
Procedure
Create the referenced source system in the Data Warehousing Workbench or define mapping to a known source system in table RSLOGSYSMAP.
You get to maintenance using Tools -> Conversion of the logical system names.
============
I have checked at the table RSLOGSYSMAP and all source system mappings are in order.
And the weird thing is, upon checking the PC itself in the transport-to box, I can activate it without any error.
FYI, we are currently upgrading to BI Accelerator. Am not sure if this could be one of the reasons.
Any inputs and tips are highly appreciated and will be rewarded with points accordingly.
ThanksHi,
This error is due to the fact that the
mapping table for the after import (RSLOGSYSMAP) is not correct maintained in PB7 system.
You need to maintain table RSLOGSYSMAP in each system
You can find the steps to do it in the attached note 127326:
o Maintain table 'RSLOGSYSMAP' in the target BW with view
'V_RSLOGSYSMAP' and enter as 'original source system' the logical name of the source system in the source BW and as 'target source system' the logical name of the source system in the target BW.
This maintenance is required since it allows the correct source system reference of the InfoSources to be transported.
This source system reference in turn is absolutely necessary to activate the transfer structure.
Example:
Source BW with source system AAA.
Target BW with source system BBB where the source system AAA
corresponds to the source system BBB.
Entry in RSLOGSYSMAP in the target BW:
Original source system: AAA, target source system: BBB.
Give the DDIC user in the source BW in client 000 the
authorization profile S_RS_ALL to create BW objects.
Cheers
Rajesh -
Variant YAE14 does not exist- F.27- Customer statement
Hi All,
User is getting an error message as Variant YAE14 does not exist. Message no. DB612. Variant YAE14 is correctly assinged to the company code and variant and print program is correctly defined in OB77 and OB78 respectively.
Kindly advice.
Diagnosis
You selected variant YAE14 for program RFKORD11.
This variant does not exist.Have you created the variant for your program (Not asking about the assigning it in OB78)
Create it through SE38
or
IMG ==> Accounts Receivable and Accounts Payable ==> Vendor Accounts ==> Line Items ==> Correspondence ==> Make and Check Settings for Correspondence ==> Create Report Variants for Correspondence
Create with the same name (The variant name must be matched with the error variant user is getting) -
Variant BP_CASH does not exist.
Hi frnds,
Variant BP_CASH does not exist
Message no. DB612
Diagnosis
You selected variant BP_CASH for program RFCASH20.
This variant does not exist.
Procedure
Correct the entry.
in Prd while doing fbcj tcode.
Tryng to take printout of the screen by selecting Print cash journal the above error is cmng and its going out of the screen..
Note : In development is working without any issues pl guide to solve this issue in Production.
Thanks in advance.Thanks
-
Dear Friends,
Using T.code F.61 ( Trigger for correspondence) , I entered correspondence - SAP11(Customer Credit memo), Company code:2000, Document No:2000000,Fiscal year 2011 and excuted.
I am getting the error as follows,
Variant SAP11 does not exist
Message no. DB612
Diagnosis
You selected variant SAP11 for program RFKORD50.
This variant does not exist.
Procedure
Correct the entry.
Please suggest how to solve the error.
Regards
SridharHi Sridhar,
Variant are client specific so you have to create the variant in the client your are testing this scenario.
Just make same variant in client and test the scenario. -
Layouts - Variant &1 does not exist for version &2 of layout module &3
Hi Sap All.
when i am trying to create IDOC's of type LAYMOD01 using LSMW with IDOC Object type ,there were some IDOC;s failing in SAP With status 51 saying as "Layouts - Variant &1 does not exist for version &2 of layout module &3".
the following below text explain you the error message related to one particular IDOC of type LAYMOD 01 which was failed in sap with status 51 :
Variant 6325 does not exist for version 0000 of layout module EC-83-0214
can any one explain me the reason on why the IDOC's were failed.
regards.
Varmanot required any more
-
Error: Selected disk does not exist (21) Module-SRE-700
Already tried everything that the recovery cisco commands, anyone have idea how to solve the problem of the print shown in print?
Initializing memory #2. Please wait...
This may take a minute....
Serial ATA Port 0 : Hitachi HTE545050B9A300
DDR Memory 4096 MB detected
Intel(R) Core(TM)2 Solo CPU L3400 @ 1.86GHz
BIOS SM 3.52.8, BIOS Build date: 02/08/2011
System now booting...
Please wait...
Please press P to select Primary Boot Loader ...
or S to select Secondary Boot Loader ...
or wait to boot from default configuration ...
Now booting from primary boot loader....
Authenticating boot loader....
Primary Boot Loader Authenticated - booting....
ServicesEngine boot-loader> install_key waas-accelerator-4.4.5c.4-k9.bin
Keyfile Size 202814577 over limit 32768 will not burn into flash
ServicesEngine boot-loader> verify
Loading disk:/bzImage ... Unable to load image
Error: Selected disk does not exist (21)
Unable to boot image
Unrecognized command
ServicesEngine boot-loader>
#service-module sm 1/0 session
Trying 172.20.245.1, 2067 ... Open
Please wait...
Please press P to select Primary Boot Loader ...
or S to select Secondary Boot Loader ...
or wait to boot from default configuration ...
Now booting from primary boot loader....
Authenticating boot loader....
Primary Boot Loader Authenticated - booting....
Please enter '***' to change boot configuration:
Trying to reset Service Module SM1/0.
May 7 11:27:33.055: %SRE_SM-6-STATE_CHANGE: SM1/0 changing state from SERVICE_MODULE_STATE_ERRQ to SERVICE_MODULE_STATE_SHDN
Initializing memory #1. Please wait...
Initializing memory #2. Please wait...
This may take a minute....
Serial ATA Port 0 : Hitachi HTE545050B9A300
DDR Memory 4096 MB detected
Intel(R) Core(TM)2 Solo CPU L3400 @ 1.86GHz
BIOS SM 3.52.8, BIOS Build date: 02/08/2011
System now booting...
Please wait...
Please press P to select Primary Boot Loader ...
or S to select Secondary Boot Loader ...
or wait to boot from default configuration ...
Now booting from primary boot loader....
Authenticating boot loader....
Primary Boot Loader Authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialize network device
Backup current platform configurations....
SRE step 1 - SM registration...
Finding (hd1,3)/296e03bc-3236-4a68-a178-688e56400a1e, failed
Local install not supported
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait ................... done.
May 7 11:29:03.331: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration RequestLoading disk:/bzImage ... Unable to load image
Error: Selected disk does not exist (21)
Unable to boot image
þ
Initializing memory #1. Please wait...
Initializing memory #2. Please wait...
This may take a minute....
Serial ATA Port 0 : Hitachi HTE545050B9A300
DDR Memory 4096 MB detected
Intel(R) Core(TM)2 Solo CPU L3400 @ 1.86GHz
BIOS SM 3.52.8, BIOS Build date: 02/08/2011
System now booting...
Please wait...
Please press P to select Primary Boot Loader ...
or S to select Secondary Boot Loader ...
or wait to boot from default configuration ...
Now booting from primary boot loader....
Authenticating boot loader....
Primary Boot Loader Authenticated - booting....
Please enter '***' to change boot configuration:
Detect and Initialize network device
Backup current platform configurations....
SRE step 1 - SM registration...
Finding (hd1,3)/296e03bc-3236-4a68-a178-688e56400a1e, failed
Local install not supported
Response - no installation needed (len: 422)
SRE Installation Not Needed
Restoring orignial configuration...
Updating flash with bootloader configuration.
Please wait ................... done.
May 7 11:30:31.339: %SM_INSTALL-6-INST_RBIP: SM1/0 received msg: RBIP Registration RequestLoading disk:/bzImage ... Unable to load image
Error: Selected disk does not exist (21)
Unable to boot image
ú
Initializing memory #1. Please wait...
Initializing memory #2. Please wait...
This may take a minute....
Serial ATA Port 0 : Hitachi HTE545050B9A300
DDR Memory 4096 MB detected
Intel(R) Core(TM)2 Solo CPU L3400 @ 1.86GHz
BIOS SM 3.52.8, BIOS Build date: 02/08/2011
System now booting...
Please wait...
Please press P to select Primary Boot Loader ...
or S to select Secondary Boot Loader ...
or wait to boot from default configuration ...Hi,
Opened a tac and managed to get the resolution of the problem. For those with the same problem reported by me above just follow the procedure below:
1. uninstall existing SRE-V software
http://www.cisco.com/en/US/docs/interfaces_modules/services_modules/sre_v/1.5/user/guide/software.html#wp1055364
2. run sm-hw-util to set sata mode to IDE
http://www.cisco.com/en/US/docs/interfaces_modules/services_modules/sre_v/1.5/user/guide/software.html#wp1091438
3. configure a static, 32bit route to point the service module IP address to the SM slot/0 interface
ip route 255.255.255.255 SM slot/0
4. install WAAS:
http://www.cisco.com/en/US/docs/app_ntwk_services/waas/waas/v421/module/installation/guide/wssmcfg.html#wp47040
http://www.cisco.com/en/US/docs/interfaces_modules/services_modules/sre_v/1.5/user/guide/software.html#wp1091438 -
Error ACLContainer: 65315 does NOT EXIST in the Object Cache for parentID:
Expert,
I did the following steps to upgrade the OWB repository from 10g to 11g
• Created a dummy workspace in the 11.2 repository
• Created users in the destination environment
• Run Repository Assistant against the 11.1 source database
• Then selected *“Export entire repository to a file”* and selected the MDL(10g) to import
After 99% of completing I have got the below error
Error ACLContainer: 65315 does NOT EXIST in the Object Cache for parentID: 65314
Please let me know the solution.
Thanks,
Balaa...Hi I had the same error and worked on it for almost a week with no success but there is few work around for this try it it might work for you.
Step 1>Run a health check on OWB 10.2 enviroment(make sure you clone your OWB 10.2 enviroment and then do this healthcheck ,these checks are tricky )
refer
Note 559542.1 Health Check of the Oracle Warehouse Builder 10.2 Metadata Repository
This will give you info about your missing ACL
Step 2> download these two scripts fixLostACLContainer.sql ,fixAllACLContainers.sql
please refer :
Note 559542.1 Health Check of the Oracle Warehouse Builder 10.2 Metadata Repository
OWB 10.2 - Internal ERROR: Can not find the ACL container for object (Doc ID 460411.1)
Note 754763.1 Repository Cleanup Script for OWB 10.2 and OWB 11.1
Note 460411.1 Opening Map Returns Cannot find ACL Containter for Object
Note 1165068.1 Internal Error: Can Not Find The ACL Containter For for object:CMPPhysical Object
It might resolve this ACL issue but it did not work for me.
If none of these work then
Perform export from design center of OWB 10.2 and import through design center of OWB 11.2.(ONLY OPTION)
It worked for me.
Varun -
HTTP Error 404 :File does not exist
Hi all,
On Test instance we are not able to open the help file,it give an error
HTTP Error 404 :File does not exist
can anybody have solution for this
it's very urgent
Thanks
shekharI have changed the note server definition in the external app to add the mail directory in front of the mail file name 'mail/mufile.nfs' and I get the following error:
05/04/21 15:15:07 lotusnotes: [instance=(null), id=97176201941,7] ERROR: LotusServiceSession: getConfigProperties(): An error occured
while reading/ retrieving the properties from the the configuration file.
05/04/21 15:15:07 lotusnotes: [instance=(null), id=97176201941,7] ERROR: Unhandled exception in SOAP call
oracle.portal.provider.v2.ProviderException: LotusServiceSession: getConfigProperties(): An error occured while reading/ retrieving the
properties from the the configuration file. -
Excise Invoice creation error -Billing document does not exists
Dear Experts,
I have created supplementary sales order, billing with refernece through sales order by VF01.
Now I want to create Excise Invoice but system gives error Billing Document does not exists
I have checked billing document in VBRK table & it is showing in table.
My item categroy is L2N -and set it to C
I have assigned Billing type under Outgoing excise invoice ->Assign billing type to delivery type still my excise invoice is not generating.
Pl. guide me.
Thanks
TruptiResolved my problem.
Actually in Billing item categroy if you put SD Doc. Catg. as M you can do excise invoice even if you have not created the
outbound delivery.
So cycle will be Supplementary Sales Order->VF01 with ref. to SO->J1IIN -Excise invoice creation.
Thanks to all.
Trupti. -
Error "Item 000010 does not exist" while creating sales order in VA01
Dear All,
As per customer requirement we are trying to validate shipping data( item level) and unloading point( item level) by customer enhancement.
Enhancement: V45A0003
Function Module: EXIT_SAPMV45A_003
INCLUDE: ZXVVAU05
Inside include we have written validation code that if user enters any wrong value for shipping data or unloading data
system will throw error message accordingly.
It is working fine and we are getting error message if wrong shipping data or unloading data is entered.
But after the error message is displayed if we try to save the sales order again system throws a STOP message as a POPUP
saying "Item 000010 does not exist".
Now,if we enter proper shipping data or unloading data and try to save the salesorder it is throwing error "Item 000010 does not exist"..
Please let me know your valuable input on this.
Regards
Arindam
Edited by: Arindam Ganguly on Mar 11, 2010 1:55 PMIt sounds like your error routine has prevented the insertion of the data in VBAP or XVBAP internal tables. Therefore, upon return to the screen and SAVE, SAP is examining the VBAP or XVBAP table, comparing to the 'I' index table probably, and finding that there is supposed to be an item 10, but it's not in the necessary table(s). This may be resulting because your internal tables are now inconsistent.
Look at where your inserted error coding is occurring...you may want to move that to the SAVE_DOCUMENT_PREPARE routine in MV45AFZZ, so that everything will have been built, and a final check of the content will stop the sales order save until the data is corrected.
Edited by: Breakpoint on Mar 11, 2010 3:29 PM
Maybe you are looking for
-
Itunes not working, get "missing file, reinstall itunes" message.
1. Itunes not working, get "missing file, reinstall itunes", message. 2. When try to reinstall itunes, gets as far as "starting services", then stops with message, "Apple mobile device failed to start. Verify that you have sufficient privileges to
-
Remote disc in finder devices - can't remove it
I have a "remote disc" item in my finder under devices and cannot eject or remove. iMac, OS X Version 10.6.7 Background: I have 2 very old Compact Flash USB card readers (Intelliflash and ImageMate) and several Compact Flash cards that I wanted to vi
-
I have created a New Warehouse in Admin/Setup/Stock Management/Warehouses. Because I wanted to search first for existing Warehouses, I put * in the Warehouse Code Field and I pressed return. However, because the programme was in ADD mode, instead of
-
NAC - Using ActiveX web agent with low level user
Hi: I have NAC installed in-band and running. We have a group of test taker with user rights to the PC. The ActiveX web agent will not load and the Java agent does not start. Any suggestion o dealing with some low secuirty issue and the browser. Than
-
OS X 10.6.8 Disk Utility Issue
I am running OS X 10.6.8 Through disk utility, I have been informed that the hard disk needs to be repaired by booting from my OS X disk, and running the utility. The problem is I can't find my disk. Any other solutions?