Alert message 1611

Could someone help me to exit from a recovery mode for my iphone? I've searched through many website and tried many ways but still can't have the problem fixed.
An alert message 1611 comes out when I wanted to get an updated itunes. I tried re-booting my pc. I tried unintalled itunes and all other Apple softwares and reinstalled them. I tried restoring my iphone. None of these works.
I also tried downloading iREB and LibUSB as demonstrated in Youtube, but found no way to download libusb-2in32.exe.
Please help...

Hi,
Disable anti virus software and turn off the Firewall on your PC.
Help here: Update and restore alert messages on iPhone, iPad, and iPod touch including Error 1611
Carolyn

Similar Messages

I have updated the iPhone for and an error message 1611 has appeared and my phone no longer works. Any suggestions please?

I have updated my iPhone 4 with itunes 10.5 and my phone has stopped working and it only comes up with an error message 1611 saying there is a hardware issue - yet all I did was plug it to my computer. Help would be good as I need my phone for work, personal etc and it is annoying that an update can stop my phone from working.

Error 1611: This error may indicate a hardware issue with your device. Follow the steps in this article. Alsoattempt to restore while connected with a known-good 30-pin Dock Connector cable, computer, and network to isolate this issue to the device. The MAC address being missing or the IMEI being the default value (00 499901 064000 0) can also confirm a hardware issue. Out-of-date or incorrectly configured proxy or security software, such as FoxyProxy, can cause error 1611. To troubleshoot third-party security software, follow these steps.
From here > iOS: Resolving update and restore alert messages

Filename in an alert message

Hi Friends,
I am doing a simple file to idoc scenario.
if mapping error occurs.
the requirement is to trigger an alert which says "A mapping error occurred when processing the file XYZ.txt"
Constraints are:
1. BPM is not used as it is a simple scenario.
2.RFC lookup during mapping is to be avoided since if mapping itself fails then it will be of no use.
Is there a way/work around to get the filename dynamically in the alert message.
Thank you,

Seems to be not possible without a BPM.....at least by using a standard alert procdure
Using a mapping get the FileName .....have both the source and target message as the same.....
map the FileName to some empty node of the structure.
In the mapping logic, one for which you want to check for any exception, do not make use of the node containing the FIleName...let the rest mapping remain as is
Create a Container Variable and Assign the node containing the FileName to it using a Container Operation.
Then raise the Alert.
I have used a similar approach in one of my interfaces.
Regards,
Abhishek.

Display an Alert message in PL/SQL block in APEX

Hi,
we are getting an oracle exception while inserting a new row. As it is having the unique constaint on a coulumn.
Now the problem iis we need to Display an "Alert message" based on the input field validation. That java script code for alert has to be embeded nside a PL/SQL block in Oracle APEX Application.
we tried doing this with below code:
Begin
INSERT INTO <<table name>>(ID,NAME) VALUES (s1,:TXT_s2);
exception when others then
htp.p('<script language="javascript">');
htp.p('alert("Exception");');
htp.p('</script>');
end;
If anybody knows .... please reply.
Thanks,
Subarna
Edited by: user9955252 on Apr 21, 2010 1:47 AM

Hello,
APEX Forum is here : Oracle Application Express (APEX)
Regards

An alert message observered while appling latest patch MLR 10

Hi Gurus,
While applying latest patch MLR10 we observed an alert message as below
"Creating log file "C:\oracle\midtier\.patch_storage\8404955\Apply_8404955_05-21-
2009_15-44-27.log"
Conflicting patches: 8204237,
Patch(es) 8204237, conflict with the patch currently being installed (8404955).
If you continue, patch(es) 8204237, will be rolled back and the
new patch (8404955) will be installed.
Note: If the patch currently being installed (8404955) is rolled back,
it is recommended that the fixes being rolled back here (8204237, ) are reinstal
led.
If a merge of the new patch (8404955) and the conflicting patch(es)
8204237, is required, contact Oracle Support Services and request
a Merged patch.
Do you want to STOP?
Please respond Y|N
Should we rollback the previous patch before applying MLR10 ? or can i continue with patch application ?
Thanks in advance,
Regards,
Cema

Please continue the MLR10 patch installation, this message would appear for the all patch installation (of course, patch number would be different though).

An alert message pops up upon opening saying could not initiate application security component, and it says to check to see if profile has no read/write restrictions.

An alert message pops up upon opening saying could not initiate application security component, and it says to check to see if profile has no read/write restrictions. Than when it opens all of my saved passwords are gone, I use a master password and its disabled. When I try to enter in a new on e it says can't change password. I can't even open yahoo e-mail says that my ssl security is down but when I check it its clicked. I'm just very confused as to whats going on.
== This happened ==
Every time Firefox opened
== 5/14/2010 ==
== User Agent ==
Mozilla/5.0 (Windows; U; Windows NT 6.1; en-US) AppleWebKit/532.5 (KHTML, like Gecko) Chrome/4.1.249.1064 Safari/532.5

See [[Could not initialize the browser security component]]
Rename (or delete) secmod.db (secmod.db.old) in the [http://kb.mozillazine.org/Profile_folder_-_Firefox Profile Folder] in case there is a problem with the file.

Can we use the value of a variable in an alert message

I have a variable in forms6i. I want to use the value of this variable in an alert message. How is this possible?

Gul wrote:
I have a variable in forms6i. I want to use the value of this variable in an alert message. How is this possible?Try
DECLARE err_txt VARCHAR2(200) t;
al_id ALERT;
al_button Number;
BEGIN
al_id := FIND_ALERT('My_Error_Alert');
SET_ALERT_PROPERTY(al_id, alert_message_text, 'Hello how are you mr. variable '||:variable_name );
al_button := SHOW_ALERT( al_id );
END; Hope it works..
Hamid

How to stop printing the crystal report with an alert message

I am having a field called "APPROVAL" in my stored procedure with which I prepared the CR. I want that if the value in the filed is 'A' then only the crystal report should print else it should prompt with an alert message.

Hi Sreejith,
Check this helps you:
Create an alert from "Report -> Alerts -> Create or Modify Alerts" with below steps:
1. Provide name of the alert (say Alert1)
2. Click on X+2 in front of "Message" field and write the Alert message you want to display.
3. Click on Condition button and write the condition If not({APPROVAL}='A') then true;
The above Alert will prompt with configured alert message when {APPROVAL} field is not having value of 'A'
Now, in a formula, write below content and display it where you want to display the APPROVAL field value:
If {APPROVAL} = 'A' then
{APPROVAL}
This formula content will be blank if the value of {APPROVAL} is not 'A'
Thanks,
Raghavendra

When I am writing an email, I get an alert message that says "The message could not be copied or moved to the drafts folder. Writing to the folder failed. To ga

When I am writing an email, I get an alert message that says “The message could not be copied or moved to the drafts folder. Writing to the folder failed. To gain disc space, choose Empty Deleted and choose Compact Folders and try again.”
If I do that, I get a message saying “There was an error copying to the Sent folder,, retry?”
If I retry it sends the uncompleted email. All I can do is keep deleting the message and carry on. Then the whole business might repeat itself.
Help!
Frank

Because the location for each song in your library is on your hard drive. If the hard drive isn't there, how can iTunes play it?
You'll have to move/copy the music from your hard drive to your computer's hard drive.
Basically, EASIEST way to do all this, if you don't care about your play counts, etc...
-Delete EVERYTHING from iTunes, so that your library is now empty.
-Go to "Advanced" inside of the "Preferences" window, found in the "Edit" drop-down. You can also access Preferences by pressing Ctrl+, (Press Ctrl and the comma key)
-Change your iTunes Media Folder Location to something simple, but on your computer. I use C:/iTunes. Make sure "Keep iTunes Media Folder Organized" and "Copy files to...." are both checked. You can close Preferences now.
-Now, drag and drop your music from your hard drive into your iTunes library. iTunes will automatically add the music to your library, as you would expect, and also creates a copy of each file to place into that iTunes Media Folder you just created.
Shouldn't have any more problems...

Cash account with nagative balance shows an alert message

Hi All,
when user create any type of Outgoing Payment , Incoming Payment, deposits , Journal Entry with the Cash account which is active accounts and the account balance is less than ZERO so system gives an alert message on the screen I want this type any query or any store procedure.

Hi ,
As far as i am understanding your query this may be for outgoing payment.
Do you want to stop a outgoing payment from cash account? if balance in this account is zero.
Clerify your question.
Thanks
Ashutosh

Outlook 2016 getting crashed and throws an alert message as "microsoft outlook has encountered a problem and needs to close.

Hi,
Today i installed Microsoft Office 2016 preview for my Mac OS X 10.10 Yosemite. Word, Excel and Powerpoint applications are working without any problem. However, Outlook getting crashed and throws an alert message as "microsoft outlook has encountered a problem and needs to close.", it's happens always, when i launch outlook. please suggest me, how can i comet from this issue.
Thanks in advance,
Suresh Balakrishnan.

Go to the Microsoft site for help. These forums are not offering support for MS products, especially not for beta products.

Firefox does not opens. It shows an alert message -"Your Firefox profile cannot be loaded. It may be missing or inaccessible."

Firefox window does not opens. It shows an alert message -"Your Firefox profile cannot be loaded. It may be missing or inaccessible." I have deleted the processes in task manager and restarted Mozilla.Even then it does not opens. Pls get me a solution.

Make a new profile ('[[managing profiles]]'); if the old profile directory is still there, just copy-and-paste its contents into the new profile directory.

My ipad was is displaying an alert message " A wi-fi connection is required to download your apps and media". So it has been connected to the internet over night and this morning but is still displaying the alert message and it won't go away. what to do?

Hi,
My name is Norbert. I am having some difficulties restoring my icloud back up. My ipad was doing an icloud back up and the alert message displayed on the ipad after my internet was interrupted "A wi-fi connection is required to download your apps and media".
I got the internet working, my ipad is receiving internet network but the alert message is still displayed on the ipad and won't go away, to make matters worse the ipad is frozen and i can't do anything.
Please can anyone with a similar experience tell me what to do in this situation?
Thank you

Welcome to the Apple Community.
Have you tried a hard restart. Press the on/off button and homescreen buttons together until the device shuts down.

Is it possible to make an alert message.

Hi,
Anyone knows if it Is possible to make an alert-message that pops up ( f.e as a little window) on a specific day to remember me of something I have to do that day?
Would be handy.
Is this possible with Tiger or is there a third party application that does the trick?
Thanks in advance.

Try a free widget called quikAlert
http://www.apple.com/downloads/dashboard/business/qwikalert.html
Regards
TD

Why do i keep getting an Alert message saying "The URL is not valid and cannot be loaded "?

Why do i keep getting an Alert message saying "The URL is not valid and cannot be loaded "?
This happens a lot regardless of the web page. I continually have to restart FF and it persists still

Start Firefox in [[Safe Mode]] to check if one of the add-ons is causing the problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).
* Don't make any changes on the Safe mode start window.
See:
* [[Troubleshooting extensions and themes]]
* [[Troubleshooting plugins]]
If it does work in Safe-mode then disable all extensions and then try to find which is causing it by enabling one at a time until the problem reappears.
* Use "Disable all add-ons" on the [[Safe mode]] start window to disable all extensions.
* Close and restart Firefox after each change via "File > Exit" (Mac: "Firefox > Quit"; Linux: "File > Quit")

Alert message 1611

Similar Messages

Maybe you are looking for