Alert status GREY in BPM configuration
Hello Everybody,
I am configuring BPM in Solution Manager for "Order to Cash" process concentrating on "IDOC monitoring". The IDOC monitor will monitor the IDOC status in my ECC system, so no need to define interfaces.
The configuration is completed without any errors. But once i go and check the alerts, i see that alert status as GREY.
It says "MTE node inactive".
I have done the following troubleshooting -
1. I have checked the ST-PI and ST-API tools and they are as per the prerequisite.
2. I have assigned the necessary auto reactions in RZ21 again
3. I have applied SAP note - 1587042
4. I have reorganised the alerts
5. I deleted the corresponding MTE in RZ20 and regenerated the alerts
6. I reset the node
7. The collector status is green
8. Involved SAP in this issue but they are slow in responding.
9. All RFCs working fine
Looking out for an immediate help / suggestions on this issue.
Thanks,
Manan Joshi
Post the information regarding system components.
Similar Messages
-
SCOM 2012 - ServiceNow connector - alert status "Forward Pending"
Hi,
Installed the connector available under here:
http://www.servicenowguru.com/integration-tools/integration-update-sets/
Steps followed: http://wiki.service-now.com/index.php?title=Microsoft_System_Center_Operations_Manager_SCOM_Integration
However, the alert status is "Forward Pending". What can be the reason behind it?
Anyone have the correct configuration steps for this connector? Following warning message logged every second in event viewer:
Exception in timer function:No such host is known
Any suggestions much appreciated!!For this issue, you can check below link
http://social.technet.microsoft.com/Forums/systemcenter/en-US/e48cabab-b385-4156-84c1-f732a1285ccb/alert-forwarding-status-in-scom
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question, please click "Mark As Answer"
Mai Ali | My blog: Technical | Twitter:
Mai Ali -
Alerts through Email Using BPM
Hi Friends,
can anybody help me on BPM as i am new to BPM.I need a help from you , i want to send an alert through Email using BPM can any body send me a sample scenario related to this one.In BPM you create the Alerts. In Alert Configuration (in RWB) you can define for each Alter Category whether it is to be forwarded via Email.Prerequisites for that:
1. XI/PI must have been configured to send Mails (SMTP)
2. All receivers must have maintained an Email Adress in SU01
3. Only users defined in XI/PI can get the mails.
4. Schedule the regular sending of Emails out of the XI/PI system using transaction SCOT
5. The Mail Server (Lotus Domino or Exchange Server) must accept Mails from XI/PI system (Server and Port). Ask your Mail Guys.
6. If you do not define the Mail Server as IP address in SMTP configuration take care that the XI/PI is able to resolve Server Name to IP Address (e.g. by maintaining local hosts ob XI/PI).
Hope this helps!
Regards,
Volker -
Which driver to use in the BPM Configuration Steps?
Hi,
I´m in the BPM configuration steps and we will use BPM on a Weblogic Server, I´m in the step when you need to create to JDBC Data Sources for the Enterprise and Directory Databases, do you know which driver shoul I use? should it be XA o Non-XA?
Thanx in Advanced!
Kind Regards,
Gerardo JSince there are no drivers, you can create your own, request one, use the Instrument I/O Assistant, or hope someone has one and posts it here. For help on creating one or requesting one, see the main Instrument Driver Network page. As long as you are familiar with the instrument and have the manual, creating a driver is not that hard.
-
BPM Configuration Error on Weblogic Configuration
Hi,
I try to configure BPM Directory and always get error on wlst.sh command
weblogic.common.resourcepool.ResourceSystemException: Cannot load driver class: weblogic.jdbcx.oracle.OracleDataSource
My system spec:
- Solaris SPARC 64
- Weblogic 10.3.0.0 using JRockit 1.6.0_16
- BPM 10gR3
The configuration error in weblogic configuration.
Really need help here..
Thanks
Regards,
Eric WijayaHi Eric,
Just checking: Are you using BPM 10.3.2?
Do you mean the BPM Directory Configuration?Yes, I'm talking about the directory configuration and the engine configuration too.
I've configure the BPM Directory to use BPM's Oracle Driver Version:10,11 which is selected by default by the BPM Configuration Wizard but still got the jdbc driver error. If you are using 10.3.2, you will see that there is another driver called: "Oracle Driver Version:10,11" (without BPM!!). You must use that driver. (if you install the latest 10.3.2 HF, that driver is the default one).
If you don't have that driver, then you are using an older version than 10.3.2. Please migrate to 10.3.2.
Hope this helps,
Ariel -
Can we able to see the Work Items status in the BPM Workspace
HI,
Can we able to see the work item status in the BPM workspace.
For exampls, I have create the request as requester then it will go for approval.
After sometime i login into the workspace can i able to see my request status(it mean where it is like approval1, approval 2)?
Pls let me know, its possible in the BPM workspace.
Regards,
Anandh PHello Anandh,
You can utilse the filter option of the BPM workspace.
When you filter the instances you can view the status of all the instances even if they are currently not assigned to the particular user.
All you need to do is click on the show filter link.
Select the process from the Filter by: combo box.
Check the status boxes and click on apply filter.
You will be able to view the instance even if it is not assigned to you.(Though you will not be able to work on it.)
If you wish to give custom messages like "pending with HR" or "Pending with Admin" then you need to add a column by creating a project variable and mapping it to the custom view. Then these messages can also be shown on the instances.
Hope ths helps.
Regards,
Jaydev Doshi -
Problem with BPM Configuration
Hi,
I'm not able to get the process of BPM Configuration.
My Scenario is
File->R/3(BAPI)->File(Response),through BPM
1.Do i need 2 Business Service?
Is the flow like this?
File->IP->SAP->IP->File.
If it is correct then why do I need Business Service?
Correct me if i am wrong.
I'm very much confused with BPM,Need Help.
Regards,
Prashanth K.R,Hi Prashanth,
>>1.Do i need 2 Business Service?
no you don't need 2 one is enough
but in fact sometimes it's good to have two...
let's say one folder ackts as a foderl for storing XML files on one server for CRM data
the second on is for txt data for EDI
if you use two then you know which folder is responsible for what...
BTW
use can define Business Service in less then 20 seconds
>>>File->IP->SAP->IP->File.
If it is correct then why do I need Business Service?
you use business services to define that file adapter
is not connected to any other application
if you just use a file folder on ftp then you have to create a business service to define the sender/receiver
Regards,
michal
Message was edited by: Michal Krawczyk -
Hello *,
I would like to ask 2 questions regarding BPM:
1) Is there a way to use BPM configurable parameters in order to configure the timeout of a block?
2) Where can I find a blog explaining the use of BPM configurable parameters?
Kind regards,
Heikocheck this blog- this might give u information to start....
http://wiki.sdn.sap.com/wiki/display/XI/UserDecisionstepinSAPPI7.1-Part+I
chirag -
BPM: Confirming alerts doesn't refresh alert status
Hi Colleagues,
Have anyone dealt with refreshing problems in Solman's BPM?
If I have a red alert and process it, I proceed to confirm the alert.
In this node, status is changed to green (some cases into grey).
If I get back to the first screen in the BPM, process is still in red leading to confusion to our local monitoring team. It doesn´t matter that no other alerts are current unconfirmed.
You can refresh as many times you want, system remains in red.
I have a message in support but response process is really slow.
They just recomended to apply latest version of note 0001255970 but no effects were observed.
We are in ST 400 SP 17.
Thanks,
Renato PetrulisJust as feedback from SAP Support, it´s not an error:
(...) Let me explain the difference between Current Status and Open Alerts a
little more:
Every MTE (MTE: Monitoring Tree Element. It is the actual measurement that you are interested in. For example, BDocs con ErrorBDocs con Error defined in component BDocs con Error is an MTE) has configurable thresholds. The thresholds define the values which, when exceeded, create an alert instance. Both yellow and red thresholds can be defined. The alert instance records the time at which the threshold was exceeded,and also have a corresponding status i.e. if the red threshold is
exceeded, a red alert instance is created. When you hit the 'Confirm' button, you are actually clearing the alert instances.
Whereas, in the Current Status view, you actually see the current value of the MTE, which can be red or yellow or green irrespective of what hadhappened in the past.
Therefore, the expected behaviour is that when all the alerts are confirmed, the MTE shows green in the Open Alerts view. But the Current Status view continues to show the actual current status, which may be red or yellow or green. Therefore the DSWP transaction is actually working as expected.
Edited by: Renato Petrulis on Dec 11, 2009 3:31 PM -
We have been live with alert framework for some time, but we recently noticed we are not getting alerts when mapping fails within a BPM.
All other errors are being alerted to us properly. Is there something we need to configure differently for BPM?
Thanks in advance,
MichaelHi,
Did you trigger alert from BPM ? Check the Alert sending step in the BPM.
This SAP note on ALert Trougbleshooting may help u-913858
Alerts triggered from BPM e.g- /people/michal.krawczyk2/blog/2005/03/13/alerts-with-variables-from-the-messages-payload-xi--updated
In the BPM, u can configure the Exception Branch for the Mapping. Whenever mapping exception occurs, you can trigger an alert
Regards,
Moorthy -
I have configured NW BPM scenario for the blog:
http://scn.sap.com/community/pi-and-soa-middleware/blog/2013/09/10/step-by-step-guide-for-merging-two-different-interfaces-in-netweaver-bpm
But Sender SOAP Communication Channel is not routing the message to target system and is inactive.
Also the message successfully processed through receiver communication channel and we are getting no errors in that.
Audit Log:
04.10.2013 14:26:17.846
Information
Channel CC_BPM_Send1: Send binary file "\\<Namespace>\Sender\senderA.xml", size 158 with QoS EO
04.10.2013 14:26:17.847
Information
MP: processing local module localejbs/CallSapAdapter
04.10.2013 14:26:17.848
Information
Application attempting to send an XI message asynchronously using connection File_http://sap.com/xi/XI/System
04.10.2013 14:26:17.849
Information
Trying to put the message into the send queue
04.10.2013 14:26:17.856
Information
Message successfully put into the queue
04.10.2013 14:26:17.856
Information
The application sent the message asynchronously using connection File_http://sap.com/xi/XI/System. Returning to application
04.10.2013 14:26:17.870
Information
File "\\<Namespace>\Sender\senderA.xml" deleted after processing
04.10.2013 14:26:17.873
Information
The message was successfully retrieved from the send queue
04.10.2013 14:26:17.889
Information
Executing Request Mapping "http://<Namespace>/OM_Map1" (SWCV f727cab16f8111e191d5e4520afe1f4d)
04.10.2013 14:26:17.889
Information
Message status set to DLNG
04.10.2013 14:26:17.899
Information
Trying to put the message into the send queue
04.10.2013 14:26:17.924
Information
Message successfully put into the queue
04.10.2013 14:26:17.925
Information
The message was successfully retrieved from the send queue
04.10.2013 14:26:17.936
Information
Delivering to channel: CC_SOAP_R
04.10.2013 14:26:17.936
Information
Message status set to DLNG
04.10.2013 14:26:17.937
Information
MP: processing local module localejbs/sap.com/com.sap.aii.af.soapadapter/XISOAPAdapterBean
04.10.2013 14:26:17.937
Information
XI Packaging (Bulk Mode) Option: false
04.10.2013 14:26:17.937
Information
XI Packaging (Bulk Mode) is not Enabled, Proceeding to the Normal Processing.
04.10.2013 14:26:17.937
Information
XISOAP: Received an XI message for processing
04.10.2013 14:26:17.939
Information
SOAP: request message entering the adapter with user Guest
04.10.2013 14:26:17.966
Information
Message was received by the messaging system. Protocol: XI URL: http://<Namespace>:<host>/MessagingSystem/receive/JPR/XI Credential (User): abcd
04.10.2013 14:26:17.968
Information
Using connection JPR. Trying to put the message into the receive queue
04.10.2013 14:26:18.024
Information
Message successfully put into the queue
04.10.2013 14:26:18.027
Information
The message was successfully retrieved from the receive queue
04.10.2013 14:26:18.033
Information
SOAP: completed the processing
04.10.2013 14:26:18.033
Information
SOAP: sending a delivery ack ...
04.10.2013 14:26:18.033
Information
SOAP: sent a delivery ack
04.10.2013 14:26:18.034
Information
Message status set to DLNG
04.10.2013 14:26:18.034
Information
Message was successfully transmitted to endpoint <local> using connection File_http://sap.com/xi/XI/System
04.10.2013 14:26:18.036
Information
Java proxy runtime (JPR) accepted the message
04.10.2013 14:26:18.041
Information
Calling Invoke Method
04.10.2013 14:26:18.041
Information
Message status set to DLVD
04.10.2013 14:26:18.194
Information
Back after executing Invoke Method
04.10.2013 14:26:18.194
Information
JPR successfully processed the message
04.10.2013 14:26:18.195
Information
The message was successfully delivered to the application using connection JPR
04.10.2013 14:26:18.196
Information
Message status set to DLVD
Why the sender SOAP adapter is not sending any data??
Thanks & Regards
DeepikaHi, Deepika
I am looking for this blog and it seems to be deleted by SCN. Do you still have the doc and would you mind sending it to me?
Thanks,
Jonathan. -
Hello All,
I have created a control step to trigger alert for success condition in BPM after send step.
When i executed the BPM status ready is showing for the control step in workflow logs.
Will it get executed? Otherwise is there anything else to be added for this to get executed.
Thanks in Advance
RajeshHi Rajesh,
That means it is still waiting for condition to be met. Try checking the technical details of the same. you can use Goto->technical details and check where it is waiting.
Else you can add a switch step in BPM and put the control step in one branch and cancel in the other . So, in that case atleast one of them will execute and you will come to know what the error is?
Regards,
Sachin -
I have BPM where there are multiple send steps ( Files ) and Sych Sends as well.
I would like to send alert if Send step fails. We donot have CCMS. I would still be able to send alerts to list of Users I guess. How can I achive this.
BPM steps:
Start - Receive - split - (8 Async sends in Parallel ) - Send Sync - Send Async - Stop
Do I have enclose all 8 Async Sends in a block and add Exception branch ?.Hi,
Correct You have to use On block step with exception handle step with 8 send steps..
in exception handle .. put control step , ..
in alrtcatdef.. add users specific .. whatever you want list..
Here all 8 steps with exception name in each send step..and put in fork and this should be in block with exception .. if any one fails raise exception.. by control step in exception handler..
and if you want to stop the execution / process then put another control step to cancel the process..
Else if you eant to continue after raising the alert , you have to use tranformation step and do not put second controlstep..
see some links here to get an idea..
After createing an Alert Category using ALRCATDEF. The next step will be to define an ALERT RULE.
To define an ALERT RULE, just go to your RUN TIME WORKBENCH, and select ALERT CONFIGURATION, and after that , select your ALERT CATEGORY and
and create a rule for that category.
Just check this blog by michael for a complete scenario,
/people/michal.krawczyk2/blog/2005/09/09/xi-alerts--step-by-step
Now, when you use the report RSALERTTEST under SE38, you will find your ALERT CATEGORY, and will be able to trigger it.
This same ALERT can now be used in your BPM.
The links below on Alert Management (ALM) will be of good help to you:
http://help.sap.com/saphelp_nw04/helpdata/en/3f/567ddea69d3d4c93a6aedabd08899e/frameset.htm
http://help.sap.com/saphelp_nw04/helpdata/en/3f/81023cfa699508e10000000a11402f/frameset.htm
Also go through these blogs:
https://www.sdn.sap.com/sdn/weblogs.sdn?blog=/pub/wlg/1382. [original link is broken] [original link is broken] [original link is broken] [original link is broken]
/people/michal.krawczyk2/blog/2005/09/09/xi-alerts--step-by-step
/people/michal.krawczyk2/blog/2005/09/09/xi-alerts--troubleshooting-guide
Meanwhile look at these forum threads also:
Alerts not getting triggered from Adapter Framework
Alert Configs...
Regards
Chilla.. -
I am new for Alert Configuration, no idea how to configure an alert ?
My Scenario is file to RFC.I am doing this scenario with out bpm.
If any case any error comes, i need to send a mail which contains the material number also.
With out BPM how can i achieve this ?
Study SAPhi,
yes u can configure alert without using BPM.
use the FM 'SALERT_CREATE'.
steps,
1) define ur alert category in ALRTCATDEF tcode.
2) import that category in alert configuration at RWB.
3)define the Rule for that category like sender interface receiver interface..
4)define the fixed recipient (username of the recipient)
5) now define a udf in which call the FM ''SALERT_CREATE'.
for reference please go through the bhavesh kantilal blog in sdn.
regards,
navneet. -
BPM Configuration in Message Split
Hi All,
My scenario 1:2 Message Split is like this....
Message types: MT_INPUT,MT_OUTPUT1,MT_OUTPUT2.
Message Interfaces: MI_INPUT(OUTBOUND),MI_INPUT_ABS(ABS),MI_OUTPUT1(INBOUND),MI_OUTPUT1_ABS(ABS),MI_OUTPUT2(INBOUND),MI_OUTPUT2_ABS(ABS).
Message Mappings: Source is MT_INPUT and target is MT_OUTPUT1,MT_OUTPUT2(MM_Message_Split)
Interface Mappings: Souce is MT_INPUT_ABS(ABS) and traget is MI_OUTPUT1_ABS,MI_OUTPUT2_ABS(IM_Multiple Files).
BPM steps are:One recieve step,transformation step,Fork.
Fork Branch-1:Reciever determination and Send Output1
Fork Branch-2:Reciever determination and Send Output2.
I didn't create any correlation ID in BPM.
In the configuration of XI I know that I have to create 3 reciever determinations,3 Interface Determinations, 2 Reciever agreements and 1 sender agreement.
But I am fumbling to find out the flow of message interfaces involved here, especially in the interface determinations.
Please help me, I am a newbie to BPM.........Hi Vijaya,
go through this you can get some idea
/people/sudharshan.aravamudan/blog/2005/12/01/illustration-of-multi-mapping-and-message-split-using-bpm-in-sap-exchange-infrastructure
/people/narendra.jain/blog/2005/12/30/various-multi-mappings-and-optimizing-their-implementation-in-integration-processes-bpm-in-xi
without using bpm:-
/people/jin.shin/blog/2006/02/07/multi-mapping-without-bpm--yes-it146s-possible
/people/claus.wallacher/blog/2006/06/29/message-splitting-using-the-graphical-mapping-tool
sekhar
Maybe you are looking for
-
I have tried 6 times to download itunes on my 64bit lap top. I keep getting error messages, and I have disabled the pop up blockers still nothing. Does anyone have any ideas?
-
I need to split the load of my WSUS on to another site because the amount of computers is straining the internet connection in the amount of uploads performed. However I'm having an issue at the second WSUS where only Windows 7 and Server 2003 client
-
Adding images to rows in a table depending on file type
Hello, Within Visual Composer we have a table which lists documents and contains information about the document type i.e. description = 'This is a Word Document', file type = 'application/msword' then I have uploaded the images (icons) for the differ
-
Disable Firewall for Windows 8.1 in Domain Location Network Settings via GPO
I have Clients OS XP, 7, 8 and 8.1 Now I want disable only 8.1 firewall automatic via GPO. It's possible to apply only Windows version purpose with out any group and OU. Md. Ramin Hossain
-
I have a file I have been working on for a good part of the day. 12+ hours. Saving it religously throughout the process. Opening and closing the file with no issues. At the end of the day I saved and closed out of Illustrator cs5. Life was good. I ha