All circuits busy

We have a 3825 with two PRI's terminated on it, that is the voice gateway to the PSTN for about 50 clients (200+ phones). They use varying systems including routers with FXS cards (and analog phones), CME, and SIP voice. Ocationally when someone is trying to call a customer they get a message "all circuits buys" Then they try again a few times and the call goes through.
Are there any logs I can setup on my gateway to determine if we are maxing out on channels at times, which would give this message to the people calling in?
Any thing eles I can check to determine if this issue is mine or the Telco's?

Here is a syslog message that I get when I do a debug isdn error interface ser 1/1:23
7-06-01 10:25:20 Local7.Debug 10.254.249.3 64084: Jun 1 16:25:20.572: ISDN Se1/1:23 **ERROR**: call_cleared: VOICE ERROR: Bearer capability not available(0x3A): bchan -1, call id 0xBA5F
2007-06-01 10:25:20 Local7.Debug 10.254.249.3 64085: Jun 1 16:25:20.768: ISDN Se1/1:23 **ERROR**: CCPMSG_OutCall: fails with cause 0x22
2007-06-01 10:25:20 Local7.Debug 10.254.249.3 64086: Jun 1 16:25:20.768: ISDN Se1/1:23 SERROR: call_cleared: Got a disconnect on a non-existent call (call id = 0xBA61).
2007-06-01 10:25:20 Local7.Debug 10.254.249.3 64087: <009>This probably is a call that we placed that failed.
Any ideas?

Similar Messages

When I call someone who is also on Verizon it says, "All circuits busy" what does that mean?

When I call someone who is also on Verizon it says, "All circuits busy" what does that mean?

Thanks for reaching out to us. I'm sorry you had problems contacting your friends/family.
There are normally a couple of reasons you would hear that particular message.
1.If the announcement is received when calling one specific number the issue is with that device's service provider. They would need to contact their provider and do an investigation.
2. If the announcement is received when ANY number is called the issue is with the Verizon Wireless network. At that time, we we need to open a remedy ticket (which reports it to our engineers to investigate further).
Tamara H.
Follow us on Twitter @VZWSupport

Looking for an app that will manage all my business contacts (5,000 ) by company and then by name

I'm looking for an app that will manage all my business contacts (5,000+). Want the app to categorize by company and then by name, kind of like an organization chart
Ex. Apple, Inc.
-John
-Sam
-Nicole
I just downloaded "FastContact" for free but its too slow while searching. After more research I saw "ABContacts" but don't want to pay $5 for something I may not be looking for.
Any suggestions?

The only thing available to you is the restrictiions section in settings. Due to sandboxing, apps cannot interoperate with other apps except for sending data files from one app to another if allowed. There is no app that will help you.
Settings>General>Restrictions.

Back up Assistant lost all my business contact phone numbers

Saturday My Droid 3 that had already been difficult to use because it would not keep a new phone contact and would freeze in emergencies (I am talking get an ambulance, input a doctor's number while standing in the emergency room, or in business meetings, occasions like that) started losing the screen, it would go black if I opened the keyboard and then freeze with a black screen, continuously. It would not respond to attempts to turn it off. I took out the battery for a minute and put it back in and rebooted only to have the same thing happen over and over if I tried to use an app, make a call, view picture gallery, whatever. So I took my phone to the Oklahoma City, OK Verizon Wireless Store #331769 for CUSTOMER SERVICE. I showed the sales people my frozen black screen phone and that the back was broken and was being held on only at the top and by the neoprene case. They took the battery out and put it back in and declared my problem solved and told me that my phone was like a computer and needed to be turned off once a day and kept charged. I assured them that I was aware of this and that I did turn it off and let it reset and I charged it up every night and sometimes in the day as needed. The FIRST SOLUTION was to reformat the phone which WIPED ALL INFORMATION AND APPS OFF OF MY PHONE. I let them do that and they sent me home with it to replace all my information and apps.
Now I come to find that ALL MY BUSINESS CONTACT PHONE NUMBERS ARE MISSING from using Back Up Assistant. This is critical for my work!
ALL CONTACT INFORMATION was missing on my online account! Why would that happen? I will synch what is left on my phone to my BACK UP ASSISTANT account online.
I still haven't transferred the sim card to my "replacement phone". How can I insure that I don't lose all my contact information again???
I am going to Verizon Wireless Store #331769 for CUSTOMER SERVICE directly after work. If they lose my business contact information and phone numbers, I will be forced to re-enter 200+ contacts before I leave to go out of state for work tomorrow..
Any suggestions for a positive result?
THE CUSTOMER SERVICE GIFT THAT KEEPS ON GIVING. I CAN'T BELIEVE THIS!

Hello Drucatic
I'm sorry you were not able to get the contacts back. I know how irritating it would be to reload all those contacts.Were the contacts synced with the Gmail account? Please try backing it up with Gmail. Are you able to log in online at www.verizonwireless.com/myverizon ?If so, Please log in and check the trash the contacts may of accidently been moved.
Thank you
JoeL_VZW
Please follow us on twitter @vzwsupport

How do I complain I bought my daughter a mac, it's only 20 months old and it's completely broken, we have lost all her business info and photos. I am so not happy

I am so unhappy, I bought my daughter a mac for her birthday and it is completely broken, she took it to the store in London, they told her it is corrupt, it won't turn on and she has lost all her business records and photos. I am her mum and not technical. It cost me so much for her birthday what on earth do I do now. They said she has to fix it herself!!!!!

And does she have current backups of all her important files?
Operating a business with a computer and not keeping current backups is a very dangerous thing to do. Hard drives can fail at any time. Experienced IT people will tell you there are two kinds of hard drives - those that have failed and those that are going to fail. The only question is when.
Best of luck.

CSCtq10477 - Callmanager 9.1 can't make outbound calls, Route List gets error 41 - All devices busy

Hi all
I seem to have run into bug CSCtq10477 and maybe CSCul71689 and CSCum85086, where calls can be received from an MGCP gateway, but fail outbound with Callmanager logs showing
03095771.002 |17:34:14.103 |AppInfo |RouteListCdrc::null0_CcSetupReq - Terminating a call after the RouteListCdrc cannot find any more device.
03095771.003 |17:34:14.103 |AppInfo |RouteListCdrc::terminateCall - No more Routes in RouteListName = RL_OUTBOUND. Rejecting the call
03095771.004 |17:34:14.103 |AppInfo |RouteListCdrc::terminateCall - Sending CcRejInd, with the cause code (41), to RouteListControl because all devices are busy/stopped.
03095771.005 |17:34:14.103 |AppInfo |GenAlarm: AlarmName = RouteListExhausted, subFac = CALLMANAGERKeyParam = , severity = 4, AlarmMsg = RouteListName : RL_OUTBOUND, Reason=41, RouteGroups(RG_OUTBOUND)
and a Route List exhausted alarm appearing in RTMT.
Resetting the MGCP gateway in Callmanager, bouncing the serial interface, E1 controller and No MGCP/MGCP has no impact. I could also see the circuit was not full.
We have got round this by removing the gateway from the Route Group and pointing the Route Patterns directly at the gateway and this works. I can see two of the bugs above are fixed in the latest 9.1.2SU3 code (9.1.2.13900-10), but I don't see CSCtq10477. This bug document shows some 9.1 code is OK, but not this one.
9.1(1.21020.1) - Not listed for download, is this an ES?
9.1(2.10000.11) - Not listed for download, is this an ES?
9.1(2.10000.28) - 9.1(2) - but not shown in the release notes for 9.1(2) either.
Does anyone know if the Release notes just missed this out, or does the bug document need the Fixed versions to be updated?
Thanks

Hi,
9.1(1.21020.1) is an ES.
9.1(2.10000.28) is the base version of 9.1(2) so this bug will be fixed in this version or any higher version of 9.1(2).
Upgrading to the latest ES or 9.1(1) or 9.1(2)SU3 would take care of this bug.
HTH
Manish

How to get all authorized Business area values

hi i am on bw 3.5.
users are assinged with Role1, role2, role3 etc.,
role1 assigns users with business area values 100..200
role2 assigns users with business area values 200..250
role3 assigns users with business area values 150..210
now i want to FIND any standard report or create any custom report/program which will output me
USER with all AUTHORIZED VALUES with BUSINESS AREA....
in this case its USER1 = 100.....250 basically...
maybe something like basically WHAT USERS ARE AUTHORISED FOR REPORTING ...
how to check this with specific characteristics...
or which table????

PFB authorization related tables FYI.
USR02 Logon data
USR04 User master authorization (one row per user)
UST04 User profiles (multiple rows per user)
USR10 Authorisation profiles (i.e. &_SAP_ALL)
UST10C Composit profiles (i.e. profile has sub profile)
USR11 Text for authorisation profiles
USR12 Authorisation values
USR13 Short text for authorisation
USR40 Tabl for illegal passwords
USGRP User groups
USGRPT Text table for USGRP
USH02 Change history for logon data
USR01 User Master (runtime data)
USER_ADDR Address Data for users
AGR_1016 Name of the activity group profile
AGR_1016B Name of the activity group profile
AGR_1250 Authorization data for the activity group
AGR_1251 Authorization data for the activity group
AGR_1252 Organizational elements for authorizations
AGR_AGRS Roles in Composite Roles
AGR_DEFINE Role definition
AGR_HIER2 Menu structure information - Customer vers
AGR_HIERT Role menu texts
AGR_OBJ Assignment of Menu Nodes to Role
AGR_PROF Profile name for role
AGR_TCDTXT Assignment of roles to Tcodes
AGR_TEXTS File Structure for Hierarchical Menu - Cus
AGR_TIME Time Stamp for Role: Including profile
AGR_USERS Assignment of roles to users
USOBT Relation transaction to authorization object (SAP)
USOBT_C Relation Transaction to Auth. Object (Customer)
USOBX Check table for table USOBT
USOBXFLAGS Temporary table for storing USOBX/T* chang
USOBX_C Check Table for Table USOBT_C
Hope this would help you. Role related tables would help you resolve ur issue.

Since I downloaded the new version of Firefox the other day I can no longer access all my business banking and wonder can I return to the old version

I downloaded the new version of Firefox as I was asked and also opted for 1 extra but now I can't remember what it was, an add-on.
When I have tried since to access all areas in Business Banking
I'm unable to do so, namely download next day forecasts.
I've rung HSBC and they have assured me it is not a problem with
their service as they can read my forecasts. It is very important that I can access this witout daily phone calls as cashflow is very tight.

Make sure that the Location Bar is not set to "Nothing": Firefox > Preferences > Privacy > Location Bar: When using the location bar, suggest: History,Bookmarks,History and Bookmarks
See [[Smart Location Bar]]
See also http://kb.mozillazine.org/Locked_or_damaged_places.sqlite

How do I send SMS only at ALL TIMES with an iPhone to ALL contacts? My family shares iPads under my ID and now my teenager gets all my business texts!

How do I send SMS only at ALL TIMES with an iPhone to ALL contacts? iOS 8 now forces all Apple users to use iMessage all the time with all other iOS users. The option to send as SMS only is subordinate to iMessage in iOS 8 settings and CANNOT be turned off to send only SMS texts to another iOS device! This is a serious privacy issue for all households using iOS and doing family sharing, including over a number of iOS devices, under one member's Apple ID. Why should business conversations or financial conversations between parents be readable on an iPad in the hands of a teenager or a seven year old? The answer is not as simple as "Just don't enable iMessage on your other devices," because amy family that shares the Apple ID password is vulnerable to teenagers particularly hacking into iMessage to monitor, for example, what their parents are saying. If I were Samsung or Google I would hammer this issue immediately and continually until it is fixed by Apple (and I'm not sure why they haven't yet). iMessage is a convenience but it has this serious limitation given the architecture of the Apple universe. Apple simply cannot force all its users to conduct text messaging in arbitrarily limited way, any more than it was able to force all its users to switch from Google Maps. When will Apple fix this?

Trademann wrote:
Fox, that does not work, because then you are blocked from sending any form of message to another Apple user. iMessage MUST be activated to text any other iOS device. And then Apple defaults by ALWAYS using iMessage between iOS devices.There is simply no way, within iOS 8, to send SMS only to another Apple user. Apple has made that impossible.
The SMS-only choice used to be on the same menu level as iMessage, but now it is locked WITHIN iMessage, and is not available as a choice unless iMessage is activated. Then it is limited solely to being used if iMessage is not available.
I'm sure their argument is that they are saving their customers money because iMessage is free, but they are imposing an opportunity cost on 100 percent of their user base in the guise of saving that money. What they are really doing is entrapping faithful users such as myself further within the Apple ecosystem. If I hadn't already spent thousands of dollars on my iTunes library I might consider a Galaxy ... Samsung does not deserve to regain any momentum if they can't figure out how to exploit this.
Turning off iMessage does not prevent you from sending messages to other Apple users. You can send an SMS to any iPhone without your own iMessage turned on, even if it is turned on on their iPhone.
The SMS-only option is: Turn off iMessage. Literally. That's it.

Displaying all enhanced Business Content Objects?

Hey all.
Is there a way to display all Business Content objects that have been enhanced/modified without checking each one individually?
Specifically, I am wanting to know which standard InfoObjects in our system have been enhanced, but I don't want to have to manually check each object to determine if it has been enhanced or not.
Thanks in advance.

check table RSDIOBJ field TSTPNM
(exclude 'SAP' and 'DDIC')
Edited by: RafB on Jun 3, 2009 2:35 PM

Locking All E-Business 12.1.3 application schemas

All:
I have a situation where an auditor has come in and we have promised to lock all the E-Business 12.1.3 app schema accounts (i.e.: AR, GL, AP, etc.). Last time I did this things did not work as expected. Is this supported? I know I can change the passwords using FNDCPASS and the ALLORACLE flag but my client would like them locked. Thanks all

Thanks. My auditors are a bit pushy. I see that the other Categories say that they can be locked but, you are correct, Category 6 does not mention locking as one of the options. Is there in any documentation definitively that states that those accounts cannot be locked? I am sure they can't be locked but I need some sort of Oracle documentation explicitly saying it. Thanks again

Overview of all SD business processes within a Client?

Hello Experts,
There is an internal requirement within our Org. I need to get and inform all the SD business processes that are used by a Client. Is there any short cut/t.code for viewing that or I have to go to se16 and give the document types, look for entries and decide the most used process etc...how to go about this.
Regards,
Raj

Dear N Raja,
Not sure any T-code exists for your requirement.
It is easy to find out from Order types- sales area assignment. Here you can find out the diffrent processes (Order types) mapped. Use each order type, take one document number, take document flow identify the steps invloved from order - billing, contract - billing, free goods, foc's, intercompany's etc.
Regards,
Deepu Pillai

B-ACD & All Agent busy prompt (Custom)

Hey Guys,
Need a favor. My B-ACD works fine but i uploaded a customer prompt for all agents are busy. But it still plays the default prompt even though i have named the prompt uploaded with the original name "_bacd_allagentsbusy.au"
application
service aa flash:app-b-acd-aa-3.0.0.2.tcl
paramspace english index 0
param number-of-hunt-grps 1
param drop-through-option 1
param handoff-string aa
paramspace english language en
param max-time-vm-retry 2
param aa-hunt1 2520
param aa-pilot 2530
paramspace english location flash:
param drop-through-prompt _bacd_allagentsbusy.au
param second-greeting-time 30
param welcome-prompt _bacd_allagentsbusy.au
param call-retry-timer 5
param max-time-call-retry 700
param voice-mail 2500
param service-name queue
Any help would be appreciated.
Please rate the post
Shibly Ibrahim

Hey Cario,
you are a star, didnt know about this and hearing it for the first time.
It works like a charm now. Thanks
Please rate the post
Shibly Ibrahim

All drives busy, how to free one for tape labeling?

Our backups are currently wedged because of a media shortfall.
We have a dedicated mediafamily for full backups and all of the tapes for that pool have
been exhausted. All of the drives are have backups running (paused, really) and waiting
for tapes.
It should simply be a matter of labeling more tapes, but here is the problem:
catxcr allows you to examine the transcript and choose what to do. Selecting "help"
offers the choice to label a tape
1955.1: Error: couldn't perform auto-swap - can't find usable volume in library (OB device mgr)
1955.1: : help
1955.1: tape and library manipulation commands:
1955.1: labelvol [--force/-f] <vol_spec> <se_spec> -- label volume(s)but this yields
1955.1: : labelvol -b F26091 203
1955.1: Connection reset by peerAttempts to label a tape directly fail because they are reserved by OSB processes:
[root]# obtool labelvol -f -o -Xfamily:CR-MEDIA-DUP-ARCH4 -D obt8 -b A26001
Error: unable to open qlm connection - requested drive is in useas do attempts to cancel the job and either reserve or borrow the drive for a labeling operation:
[root]# obtool canceljob 1923; while obtool resdev obt8 | grep Error; do sleep 2; done
Info: cancelled job 1923.1.
Info: cancelled job 1923.
Error: drive obt8 is in use by:
OB component Host Process
obacslibd crbkpms1-sca 7630
obtar crbkpms1-sca 13626
observiced crbkpms1-sca 7509
[root]# obtool resdev obt8
Error: drive obt8 is in use by obacslibd on host crbkpms1-sca, process 20018.
[root]# obtool borrowdev obt8
Error: unable to borrow drive obt8 - drive cannot be borrowed.Taking the drive out of service doesn't help with any of the above.
Any suggestions how we can free up a tape drive long enough to label more tapes
into this mediafamily so backups can continue?
Restarting services is one possibility but this should be considered as a last resort.
Thanks,
-pc
Edited by: pcondran on Apr 22, 2011 4:04 PM
Edited by: pcondran on Apr 22, 2011 4:05 PM

If the other tapes are expired then they will be automatically relabelled for use with this media family, so you should never need to manually label tapes unless you're trying to expire tapes that still have valid backups on them.
The borrowdev commands are applicable to a single obtool session, so you have to just type "obtool" to get into that prompt and then do the borrowdev commands in that one session.
Thanks
Rich

All free/busy requests get error 403 in iCal with MobileMe

I'm playing for the first time with looking with my availability in iCal / Lion / MobileMe CalDAV accounts.
Everything else is working well with my calendars and Mobile Me.
I can add events, remove them, edit them, the sync is working well between the web interface and iCal on my Mac (10.7)
The only thing amiss is the availability window just logs an error to the console after a short time out.
It's error 403 which seems to be a permission denied error.
Do I need to grant permission for MobileMe to publish my free/busy status anywhere?
It it locked down until I allow sharing?
Is it tied to sharing a calendar some how?
Just sending a call out to others in case I'm missing something obvious. There are instances of this error on the boards with iCal and 10.6.6. so I presume it's more a server setup / service interruption than something I can change.
Thanks for any input - even if it's a "it works for me right now" or "I too can't get mobile me status in iCal"
(p.s. Mobile Me support says they can't help - talk with iCal people.)
(p.s. After two hours on the phone with iCal - it's back to the MobileMe people to try again. I figured I'd give a shout here before I try them again...)
Here's the error message from /private/var/log/system.log
7/27/11 12:48:30.780 PM          iCal          Error Error Domain=CoreDAVHTTPStatusErrorDomain Code=403 "The operation couldn’t be completed. (CoreDAVHTTPStatusErrorDomain error 403.)" UserInfo=0x7fd30cbbe3d0 {CoreDAVHTTPHeaders=<CFBasicHash 0x10300c1e0 [0x7fff7dbf7ea0]>{type = immutable dict, count = 7,
entries =>
          0 : <CFString 0x7fff7c240c18 [0x7fff7dbf7ea0]>{contents = "Server"} = <CFString 0x7fd30cabf370 [0x7fff7dbf7ea0]>{contents = "MobileMeCalendarServer 1C97"}
          2 : <CFString 0x7fd30cd8acb0 [0x7fff7dbf7ea0]>{contents = "DAV"} = <CFString 0x7fd30cb97840 [0x7fff7dbf7ea0]>{contents = "1, access-control, calendar-access, calendar-schedule, calendar-auto-schedule, calendarserver-sharing, calendarserver-subscribed, calendarserver-principal-property-search"}
          3 : <CFString 0x7fff7c240780 [0x7fff7dbf7ea0]>{contents = "Content-Type"} = <CFString 0x7fff7dbf1640 [0x7fff7dbf7ea0]>{contents = "text/xml"}
          4 : <CFString 0x7fff7c2407b8 [0x7fff7dbf7ea0]>{contents = "Date"} = <CFString 0x7fd30cbd9810 [0x7fff7dbf7ea0]>{contents = "Wed, 27 Jul 2011 17:48:30 GMT"}
          6 : <CFString 0x7fff7c240710 [0x7fff7dbf7ea0]>{contents = "Content-Length"} = <CFString 0x7fff7dbebe80 [0x7fff7dbf7ea0]>{contents = "280"}
          8 : <CFString 0x7fd30cd636e0 [0x7fff7dbf7ea0]>{contents = "X-Transaction-Id"} = <CFString 0x7fd30cbd7060 [0x7fff7dbf7ea0]>{contents = "nk11r10me-calsvr003-10-1311293226-3551930"}
          9 : <CFString 0x7fd30cab2b10 [0x7fff7dbf7ea0]>{contents = "X-Responding-Server"} = <CFString 0x7fd30cdeda10 [0x7fff7dbf7ea0]>{contents = "nk11r10me-calsvr003 10"}
} getting free-busy information for (
    "mailto:[email protected]",
    "mailto:[email protected]"

I have a similar issue. My girlfriend is using a yahoo address and for the life of me I cannot send her an iCal invite from my me.com or mac.com address. It never shows up in her email, not in inbox, not in junk, not deleted. I get an exclamation point on her name in the iCal invite. I can send her invites from Gmail. I created a test account on yahoo and I can send invites to that test account.
Of course I can email her just fine. I can open the invite in iCal, select the down arrow on her name and select "send email" that works just fine. I try to "invite again" and nothing... this is maddening
I've deleted iCal cache, deleted her contact, tried just using her smtp yahoo address, i don't have this issue with anyone else that I know of...

All circuits busy

Similar Messages

Maybe you are looking for