All device mappings lost, including DVD, trying to install Windows 8.1 on a new SSD disk containing no OS

I have a catch-22 situation. When I installed a new SSD disk on my desktop (does not contain an OS), Windows 8.1 would not install. The error stated that there was no partition to install on. I saw a Forum describing initializing the drive with DISKPART
using the advanced tools and a command prompt I got through the windows 8.1 installation disk, which I did successfully.
I did what it described, created an active partition, an all my drive mappings were lost. Now I can't access the Windows installation disk because the mapping was lost on my DVD reader. The error says to press any key to boot from DVD, when I do this the
message just comes up again. It is clear my DVD is not spinning or being accessed. So, every solution I have read on these forums seems to depend on being able to read the DVD, which I cannot do. I have unplugged all hard drives but the new SSD and DVD
reader.
When I try to get a listing from the shell, my only option, it says nothing is mapped. My BIOS settings boot first from DVD, then from disk. It doesn't matter, the DVD cannot be accessed.
How do I map my DVD with no OS so the Windows installation disk can be accessed?

Hello LBLivnat,
With no operating system, the DVD recognization is not from Windows.
Please go to bios and check if the DVD rom is recognized in the BIOS.
Please contact the manufacturer and check if the issue is from the BIOS.
Best regards,
Fangzhou CHEN
Fangzhou CHEN
TechNet Community Support

Similar Messages

Hello, I have mistakenly deleted all partitions on my mac while trying to install windows on my macbook pro, how do i reinstall the mac os back

Hello, I have mistakenly deleted all partitions on my mac while trying to install windows on my macbook pro, how do i reinstall the mac os back. I just wanted to have them both, please help. thank you in advance

Install Mavericks, Lion/Mountain Lion Using Internet Recovery
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
Boot to the Internet Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND-OPTION- R keys until a globe appears on the screen. Wait patiently - 15-20 minutes - until the Recovery main menu appears.
Partition and Format the hard drive:
1. Select Disk Utility from the main menu and click on the Continue button.
2. After DU loads select your newly installed hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed. Quit DU and return to the main menu.
Reinstall Lion/Mountain Lion. Mavericks: Select Reinstall Lion/Mountain Lion, Mavericks and click on the Install button. Be sure to select the correct drive to use if you have more than one.
Note: You will need an active Internet connection. I suggest using Ethernet
if possible because it is three times faster than wireless.

I Lost two HDD trying to install Windows 10 with BootCamp

I tried to install Windows 10 preview on a MBP Mid 2012 and after boot in Windows installer I choose the partition and the installer fails. I tried to boot again on OSX and didn't work anymore.
Using Disk Utility it shows that the HDD is not recognized. I tried the same procedure with an old HDD, and everything happens again.
I guess that Windows 10 installer is the responsible for the failure, but I can't understand how an installer can do that.
I plugged one of these HDD on a PC, and notice that it works, the other not.
I don't know if is possible to recover these HDD since it seems to be a firmware problem.
Anyone experience something like that, or anyone who can help me? Now I fear to install Windows 10 when it'll be available to the public. I do need it on a BootCamp partition instead of Virtual Machine because of video performance.

I'm not sure if the condition is related, but that version of Windows does not appear on the current list of supported versions.

Trying to install Windows 7 on iMac Mountain Lion - Pain

Hey all,
I am having hard times trying to install Windows 7 (64 bits) on my iMac.
Have followed every steps (Boot Camp and Apple guides, checked the forums here, etc.); made the partition, downloaded the drivers onto an empty and FAT formatted USB hard disk, etc., and all that worked fast and easy.
The problem starts when it comes to install W7 (Superdrive built in so it's in a DVD): after I choose the language, right away it says "No drivers found". It supposes to ask for the drivers after the installation but it does the opposite. I have checked the drivers one by one and it recognizes some of them, but when it tries to load them a new windows pops up repeating the same "No drivers found" thing.
I even modified Boot Camp so now it can burn a ISO image onto a USB drive. Downloaded and tried another W7 version but it was worse ("no bootable device" message...)
Have checked many other threads like this, vids, etc., but have found no solution so far. Apple's help definitely *****... And this supposes to be cake. Have spent days on this and nothing.
Just in case, all I have used on this is Boot Camp (updated, 5.0.4) and everything else on my computer is updated also. Don't have any VM, nothing like that.
Don't know how to solve this and install Windows on my computer. Please somebody help me. I am far from being a tech so will appreciate your patience on descriptions. Thanks!

There are various guides for installation and compatibility on the Apple support site for Bootcamp, did you download and read them?
I have only installed Windows once with Bootcamp, that was Windows 8, I followed the instructions and it worked ok but there seems a few items that you need to be aware of, it is all in the manuals, Apple suggest you print them off for reference.
That is about as much as I can tell you.

Trying to install Windows with Bootcamp

Hello. First, I do know this has been a recurrent trouble for a lot of Mac user who have tried to install Windows using Bootcamp. Believe me, I've looked it up both here in the Apple Communities and in saint Google. My situation is, however, that I have replaced my optical drive with a SSD, and now my optical drive works externally, via USB. Everytime I try to install Windows in a dedicated partition in the SSD, it just stays forever in a blank screen with blinking cursor.
Apple's troubleshot won't work for me, and I'm beginning to think that the issue has more to do with the optical drive itself. I tried:
To install Windows on the HDD instead of SSD.
To unplug every USB (even mouse), except for the optical drive with Windows 7.
To install it via USB stick (creating a bootable .iso with Disk Utility). In this case the usb stick does not even appear when holding option key.
To try another Windows 7 version (32/64 bits).
I have even read it might be because of a bad installation of the RAM memory... this makes no sense?!
If anyone has encountered this same situation, I'd appreciate some help. Hope I can get this done, because Steam's Age Of Empires won't ever work in OS X :S
Thank you all for reading and helping!
MacBook Pro
13-inch, Early 2011
2,3 GHz Intel Core i5
8 GB 1333 MHz DDR3
OS X 10.9.5

If your Mac was originally configured with a built-in Optical drive, and it was later replaced, Bootcamp knows your original configuration and will not work properly in the modified configuration, because it uses your Mac's model string (found in About This Mac -> More Info -> System Report -> Hardware) for example, MacbookPro 11,3. The only supported method to install Windows is to restore the original HW configuration and install it and then move hardware around.
Please see Unable to Install Windows 8 on secondary Hard Disk .

Trying to Install Windows 7 onto MBP Mid-2010 but I get this "No bootable device -- Insert boot disk and press any key". What do I do?

I'm trying to install Windows 7 onto my MacBook Pro Mid-2010 (MacBookPro6,2) from a USB drive, since my Super Drive no longer will burn DVDs or CDs. I did the XCODE trick to allow me to make the bootable USB. But when it reboots after partitioning I get this, "No bootable device -- Insert boot disk and press any key" message. When I press a key after reinserting the USB it still won't boot after pressing a key. I unplugged anything connected to it and it still doesn't work. Is there any way I can get it to be recongized or do I just need to get an external disc drive and burn a disc that way?

If your computer came with an inetrnal optical drive, you must use that to install Windows.

Hi, i have tryed to install os x leopard, (its a old imac) , disk utility is greyed out , my install dvd cant find any hdd to install on , my only way to format and configure is through terminal but dont know what commands to execute

hi, i have tryed to install os x leopard, (its a old imac) , disk utility is greyed out , my install dvd cant find any hdd to install on , my only way to format and configure is through terminal but dont know what commands to execute...
i tryed diffrent commands such as diskutil eraseDisk JHFS+ Disk1
diskutil list , wont show up my harddrive , i now its functionally cause it shows up in disk utility with name and i can get info about it , but everything is greyed out can only switch between "erase , partition , recover , Raid ,....
when i click the apple in the top left corner the whole menu is greyed out... what to do ? help me please
Sincerly AppleNoob92
p.s i have no experience in apple imac's at all never used before, but im kinda windows nerd so computers i understand but this imac make my insane, cant seem to find any solutions anywhere on the WWW....

Your HD may be crashed, so you probably should use the oringinal install discs to run Apple Hardware Test in extended mode. If error codes appear this confirms a hardware failure. In addition you cannnot repair the HD using Disk Utility from the startup disk, you have to use the origninal Install discs that shipped with the computer or the most up-to-date version of OS X on a disc that you have.

Im trying to install windows 7 in on my macbook pro, i thought it just install like intel based PC, so i use windows 7 DVD, i format the harddisk, and installation failed. When i reboot, OS X is missing, because i've format my harddisk. So what should ido

Im trying to install windows 7 in on my macbook pro, i thought it just install like intel based PC, so i use windows 7 DVD, i format the harddisk, and installation failed. When i reboot, OS X is missing, because i've format my harddisk. So what should i do to make my MBP is with windows 7

Thanks for all of your help! Big time!
Guys, I been in the business working on PC and MAC for years. So I am not green at this, I was looking for some kind of option to get past the boot loader.. Which is failing.
I know how to boot into these modes.. Done tons of research before posting and couldn't find anything.
It will not go into Internet Recovery, or any thing else. I hear the sound .. then that is it.. I get nothing else..
I have tried clearing the NVRAM which is Option + Command + P + R
Still nothing..
So I thought I would try here to see if maybe there was some trick out there someone might know of that would work.
What else guys? I am hitting th keys right..

I get an error message when trying to install windows 7 on my macbook pro. The message says "windows has encountered a problem communicating with a device connected to your computer. I don't have anything connected to my computer. How do I fix this?

I'm trying to install windows 7 on my macbook pro. I went through the process of bootcamp telling it to install windows 7. Once the windows boot manager started an error message came up. The error message says " windows has encountered a problem communicating with a device connected to your computer. I don't have a usb connected to my computer. I am using windows 7 professional install disc. I can't figure out what i am doing wrong. The same message keeps coming up over and over. Am I doing something wrong or is it something else?

Well, shucks, i just spent almost 30 minutes trying to find your model user guide to explain it better, I guess they never got around to making it.....
I would just borrow another Windows disk and try installing it again and if it does it again then you might take it to an Apple Store and see if one of the "Genius' " can figure it out.
Make sure your internet is enabled and click on your blank desktop and at the top of your screen is a Help menu option, enter PRAM and it should give you a list of things relating to Pram. It may take a few seconds to list anything as it has to connect to Apples severs first. It should list the things you may have to fill back in when your done.
"P-ram" stores some common information that is used in the background, your date, time, startup disk, etc, that you don't have to re-fill when you restart, it's a little different for each computer.

HT1199 After trying to install window 7 my new iMac will not reboot back to apple. Black screen "No bootable device -- insert boot disk and press any key". How do I get out of this?

After trying to install Windows 7 in my new iMac It will not boot up back to Apple. I have a black screen with the following "No bootable device -- insert boot disk and press any key". My iMac did not come with a boot disk. What can I do?

Try holding down the option/alt key during a restart and see if you can see/select your boot drive there.

HT1338 I have been trying to install window 7 operating system through booth camp assistant, i will finish all the stages for windows to complete installation it will hook at that stage please i need help.

I have been trying to install window 7 operating system through booth camp assistant, i will finish all the stages for window to complete installation it will hook. the installation cannot be able to complete and i really install windows on it, please i need an assistance on how to go about it.

Right now I have 6 different systems installed. Windows XP, 7, and 8 plus Linux Mint, Commodore, and OS X Snow Leopard (for old times sake), all running on Mountain Lion.
I recommend reading the user manual as it greatly helps getting through the steps, however an intuitive person should pick it up fairly easily.
Thanks to BobTheFisherman for the link.
There are other ways to get Windows on a Mac but I'm a big fan of open-source software.
Give it a try. You might like it or it may not be your cup of tea.

Can't find a bootable device after trying to install Windows 7 in bootcamp

I've been trying to install Windows 7, 64 bit. Haven't managed yet due to problem that I've just posted about in a separate thread. Now, though, when I switch on it says 'can't find a bootable device'. If I switch on whilst holding down the Option key, the (OSx) internal hard drive is there and I can boot up. But I don't want to have to do that every time... Tried resetting the PRAM as advised, made no difference.

Look at Apple () -->system preferences -->*Startup Disk*
hope this helps

Trying to install Windows 7 with an ISO burned to a DVD.

I'm trying to install Windows 7 with an ISO burned to a DVD. When I do so in Bootcamp, it is unable to add a partition to my drive. Any ideas what I might be doing wrong?

From the Boot Camp System Requirements page: http://support.apple.com/kb/HT5634
Your 2007 Macbook only supports the 32 bit version of Windows 7. The correct Boot Camp version is 4.
Mac model
Windows 8
64-bit
Windows 7
64-bit
Windows 7
32-bit
Windows Vista
64-bit
Windows Vista
32-bit
Windows XP
32-bit
MacBook (13-inch, Mid 2010)
4
4
DVD
DVD
DVD
MacBook (13-inch, Late 2009)
4
4
DVD
DVD
DVD
MacBook (13-inch, Mid 2009)
4
DVD
DVD
MacBook (13-inch, Early 2009)
4
DVD
DVD
MacBook (13-inch, Aluminum, Late 2008)
4
DVD
DVD
MacBook (13-inch, Early 2008)
4
DVD
DVD
MacBook (13-inch, Late 2007)
4
DVD
DVD
MacBook (13-inch, Mid 2007)
4
DVD
DVD
MacBook (13-inch, Late 2006)
4
DVD
DVD
MacBook (13-inch, Mid 2006)
4
DVD
DVD

Have new MacBook pro tried to install windows 7 failed cant get DVD out of drive

Tried to install windows 7 using boot camp message said can't install on any of the partitions can't get DVD out to restore eject button doesn't have any effect is there a key combination to eject dvd

First try the normal methods to remove the disc. Drag its icon to the Trash can in the Dock or select 'Eject' from the File menu.
If you are running a virtual machine, e.g. VMFusion, ensure that the CD is disconnected from the virtual machine. This will sometimes allow the CD to now show up in Mac OS X.
Shut down the computer and start up whilst holding down the mouse button. This may take some time, but keep your finger on the mouse button right up until the disc comes out or the log-in screen has appeared.
If you have Toast Titanium installed on your computer, choose EJECT DISC from the menubar.
Sometimes you can successfully use the eject disc button in iTunes even if the disc is not visible to the Finder
Open Disk Utility and choose the disc you wish to eject in the left-hand pane, then click on the Eject button.
Some Macintoshes have a paperclip hole that you can insert a straightened paperclip into, manually triggering the eject mechanism.
Open Terminal and type "drutil tray eject" to eject the disc/tray, and "drutil tray close" to close the tray.
Restart the computer while holding down Command-Option-O-F, to enter the Open Firmware prompt. Type "eject cd" without the quotes, and press return. The disk ought to eject. To start into OS X, type "mac-boot" without the quotes. Press return, and the computer will continue with the startup. (This will not work on an Intel Mac. There is no Open Firmware on Intel Macs. )
If your computer has an eject button on the keyboard, restart the computer holding down the Option key. When the startup disk selection screen appears, let go of the option key and press the keyboard's eject button.
http://guides.macrumors.com/Force_Eject_a_Stuck_CD_or_DVD

I can not use my mouse or keyboard when I am trying to install windows via boot camp

Please can you help!
I can not use my mouse or keyboard when I am trying to install windows via boot camp

Starting a couple of days ago my mouse and keyboard stopped working suddenly.
How are they connected? In my case they are wireless and their receiver is plugged into my USB hub. After an update I found the OS inexplicably not recognizing my USB hub and hence any devices which were plugged into it. My fix was to
plug the receiver into a different USB port (so I could use the mouse and keyboard; otherwise I would have had to use the OSK via Touch or pen.) Once I had normal access into my machine again I used Device Manager to remove all USB controller and
hubs (including hidden ones) and I then shut down, disconnected all USB devices and powered back up, this time using only Touch to get going. Once the OS had settled down I started plugging stuff back in the way that I wanted it to be recognized.
If I didn't have Touch I would have had to have left the wireless receiver plugged in both places which I assume would be OK. I have no idea why updates have such a catastrophic effect for USB devices.
Robert Aldwinckle

All device mappings lost, including DVD, trying to install Windows 8.1 on a new SSD disk containing no OS

Similar Messages

Maybe you are looking for