All Radio Disabled for AP1252AG
Hi,
I have 4500-E serial Catalyst Switch and AP1252AG access point.
WS-X4248-RJ45V (48 Port PoE Card) is installed in 4500-E switch and access point is connected with this switch without power injector. But i am getting LOW power error in AP. AP have 3 radios (2.4 GHz). I have tested with 1 radio also but still i have same problem.
Can you please guide me to solve this problem ?
What power command i have to apply on switch port and AP interface.
Its very urgent please...
Hi Prashant,
From Steve @ Cisco;
Information on the 4500 supporting the 1252 is below:
4500 modules req switch to run 12.2(44)SG or later
WS-X4648-RJ45V-E
WS-X4648-RJ45V+E
power inline port maximum 20000
power inline auto max
From this excellent thread;
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=General&topicID=.ee6e8b8&fromOutline=&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cc1c2b6
Hope this helps!
Rob
Similar Messages
-
3600 AP %CDP_PD-2-POWER_LOW: All radios disabled
Hi All,
I am facing issue with some 3600 APs. These aps are not joining WLC. We have total 137 APs. out of which 97 are registered but rest of them are not getting registered and I am keep getting message on AP console %CDP_PD-2-POWER_LOW: All radios disabled.
While troubleshooting I noticed that Controller can ping these IPs but with drops. So I thought it is a cable issue but when I connect AP directly to switch ports still I get ping drop from controllers IP. When I look at switch port power it shows 13.0 for all non registered APs where as working one is showing 15.4. I have checked there is no network issue. WLC can ping other APs very well being in same subnet only APs which are not getting registered are not pingable 100% there are drops while pinging APs.
All APs are in same subnet and WLC MGMT interface is in different subnet. AP joins WLC via option 43.
I am attaching logs from AP console. I am runing 7.5.102
Can any body help me on this.New-ASW01# sh power in
Available:847.0(w) Used:139.4(w) Remaining:707.6(w)
Interface Admin Oper Power Device Class Max
(Watts)
Gi0/1 auto on 16.8 AIR-CAP3602I-E-K9 4 30.0
Gi0/2 auto on 15.4 AIR-CAP3602I-E-K9 4 30.0
Gi0/3 auto on 13.0 AIR-CAP3602I-E-K9 4 30.0
Gi0/4 auto on 16.8 AIR-CAP3602I-E-K9 4 30.0
Gi0/5 auto on 13.0 AIR-CAP3602I-E-K9 4 30.0
Gi0/6 auto off 0.0 n/a n/a 30.0
Gi0/7 auto on 16.8 AIR-CAP3602I-E-K9 4 30.0
Gi0/8 auto on 15.4 AIR-CAP3602I-E-K9 4 30.0
Gi0/9 auto on 16.8 AIR-CAP3602I-E-K9 4 30.0
Gi0/10 auto on 15.4 Ieee PD 4 30.0
Gi0/11 auto off 0.0 n/a n/a 30.0
================================================
Cisco IOS Software, C3560E Software (C3560E-UNIVERSALK9-M), Version 12.2(55)SE5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Thu 09-Feb-12 18:32 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x02800000
ROM: Bootstrap program is C3560E boot loader
BOOTLDR: C3560E Boot Loader (C3560X-HBOOT-M) Version 12.2(53r)SE2, RELEASE SOFTWARE (fc1)
IDF1 uptime is 5 hours, 42 minutes
System returned to ROM by power-on
System image file is "flash:/c3560e-universalk9-mz.122-55.SE5/c3560e-universalk9-mz.122-55.SE5.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
License Level: lanbase
License Type: Permanent
Next reload license Level: lanbase
cisco WS-C3560X-48P (PowerPC405) processor (revision K0) with 262144K bytes of memory.
Processor board ID FDO1716H0SJ
Last reset from power-on
2 Virtual Ethernet interfaces
1 FastEthernet interface
52 Gigabit Ethernet interfaces
2 Ten Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : 6C:41:6A:30:82:00
Motherboard assembly number : 73-12557-08
Motherboard serial number : FDO17160A8F
Model revision number : K0
Motherboard revision number : A0
Model number : WS-C3560X-48PF-L
Daughterboard assembly number : 800-32786-02
Daughterboard serial number : FDO17150GP4
System serial number : FDO1716H0SJ
Top Assembly Part Number : 800-31328-07
Top Assembly Revision Number : B0
Version ID : V04
CLEI Code Number : COMJP00ARD
Hardware Board Revision Number : 0x04
Switch Ports Model SW Version SW Image
* 1 54 WS-C3560X-48P 12.2(55)SE5 C3560E-UNIVERSALK9-M
Configuration register is 0xF -
My form has a list of yes or no questions. I want to use either cheboxes or radio buttons. Unfortunatly I can't make it work. When I check yes for one question, it marks all yes answers for all other questions. If I mark some radio buttons to answer, it unmarks later. Need immediate help!!!
Is it that you are using a PDF-based form? Did you copy and paste the Yes/No fields all the way down your form? If so, then all of the yes/no boxes are copies of each other and have the same name and properties in the PDF.
For example, if you had:
Question 1 and Question 1 Yes/No checkboxes
Question 2 and Question 1 Yes/No checkboxes
Question 3 and Question 1 Yes/No checkboxes
Question 4 and Question 1 Yes/No checkboxes
Then whatever answer you selected in Question 1 would populate down through the rest of the form.
Changing the Yes/No field properties in questions two through four would eliminate the problem.
I hope that helps,
Brian -
My ipod touch has been disabled for 212,456,875 minutes! I have followed all instructions on the apple support site to restore it but this has not worked. Help!
Without know exactly what you did or what happened:
Disabled
Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Forgot passcode or device disabled
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: Back up and restore your iOS device with iCloud or iTunes
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
If problem what happens or does not happen and when in the instructions? When you successfully get the iPod in recovery mode and connect to computer iTunes should say it found an iPod in recovery mode. -
Hi. My phone screen broke and I had it replaced from a phone shop. The guy said that while changing the screen and phone was blocked. It is now disabled for like 23,000,000 minutes and I can't restore it cause I dont have all the data sync to my computer. Is there anything I can do or can Apple do something if I give them the correct password?
As you had the iPhone opened by an unauthorised repairer ( Apple do not replace screens on iPhone 4)
Apple will not provide any service or support
Take it back to the "phoneShop" and tell them to fix it
You have no other alternatives
or try this
http://support.apple.com/kb/HT1212 -
I have a G5 and iBook with PowerPC/iTunes 10....just recently I can't bring up the preset Internet radio on either one. Is this a glitch, or have they been permanently disabled for older versions of iTunes?
I should have posted this for you a while ago. My apologies for not doing it sooner. This was passed on to me by another user R C-R
He deserves the credit for this workaround. This is his post from an area in the forum where you have to be level 6 or higher in which to participate.
I am getting the same (global) error using iTunes 10.3.1 on a 2008 MacBook running 10.6.8.
A really, really awkward workaround that works for me (for now) is if you have the URL of the Internet radio server you can go to Advanced > Open Stream... (in iTunes 10.x) or type command + U, enter it there & click OK. The station should play fine in 10.x.
You can get the URL from any version of iTunes that still supports the "radio tuning service" (which I gather is an Apple server thing Apple is no longer supporting for 10.x). Play the station normally from the newer version & type command + I to open the info window. At the bottom of the "Summary" tab you will see the URL. (Annoyingly, you can't copy the text so you will have to write it down.)
Once you have that, you can play the station in 10.x & add it to a playlist for future use.
To check this out, maybe try http://198.27.80.37/stream/mbarsott.pls -- it is a European Jazz station that works fine for me with iTunes 10.3.1.
This workaround does work, but is a bit cumbersome. I'm still holding out hope that it is just a glitch. -
I like to text into my favorite radio stations for contests and requests but after having my Galaxy S5 for a couple days the messages started coming back as Failed ... ?
You might have premium messages block.
-
When trying to update my apps on my phone, after logging in it says my account has been disabled for security reasons. I've updated my password but it still says its disabled. Any thoughts?!
Hi,
If you have followed everything in the link below, and still have the problem, click on one of the links at the very bottom under "Additional Information". That's all we can do for you here:
http://support.apple.com/kb/TS2446
Cheers,
GB -
I've been busy with school, thus making me have no time at all to use my iPad. Being the forgetful me, I can't remember my password. I tried entering some of the passwords I used but none of them worked. I forgot the recent password I've been using in my iPad. Now it's been disabled for more than two weeks. I want to use it so badly that I have to reboot it numerous times. What should I do?
FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY. -
"This Apple ID has been disabled for security reasons" Every few weeks
I have had an iTunes account for years with no issue. Lately, I have been receiving the dreaded "This Apple ID has been disabled for security reasons" message every few weeks on my iPad 2(currenly, my only iOS device). I go through the process of reauthorizing my password and info and it works again for a while, then happens again some time later. It's getting annoying. I'm not sure what's changed. Only two computers are authorized to use my account and I am the only one who can log into either of them. No one knows my info and I live alone.
The only thing I can think is that it's a bot spamming my e-mail address and passwords in an attempt to hack my account. If that's the case, am I really going to have to go through this every few weeks just to use my iPad? Don't get me started on how stupid it is to have to type in your password to update existing apps. And that's usually when I find out, not when I actually purchase one.
Is anyone else having this issue? I'm wondering if it's more widespread. Some time ago, a chinese app was mysteriously purchased on my account. Apple refunded the purchase and reset my password. That was about the time that all of this started. The reviews on the app left no doubt that it was happening to numerous people and I have no idea how they would have forced a purchase on so many user accounts.Domin Harvey wrote:
PLEEEEEEEASE, please, please fix this!!
Everyone should keep a few things in mind:
This is an occasional problem affecting a vanishingly small percentage of the installed base. Look at the numbers of actual instances in just this thread, look at the gaps in time, etc.
Many many more ... me for example ... have never seen it at all. That doesn't mean it's not an irritation for those afflicted, but it does mean that it's not something likely to be seen as a critical issue affecting the whole base.
You aren't talking to Apple here in these user-to-user forums, at all, for any reason. This sort of communication is handled through their established Feedback links. If you can suggest a better way for them to handle things then make your thoughts and feelings known at —
http://www.apple.com/feedback/ipad.html -
My itunes account was disabled for some reason. I changed password in iforgot and still didn't work. I could log in and see my music but not make purchases from the store or even redeem an itunes gift card so I set up a new login/account with another email account of mine. On the new account I can redeem my gift card and download items onto my ipad2. Is there any way to move my music to the new account?
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Click the Clear Display icon in the toolbar. Then try the action that you're having trouble with again. Select any messages that appear in the Console window. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message (command-V).
When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some private information, such as your name, may appear in the log. Anonymize before posting. -
It is probably something to do with the fact that I am in the Philippines, but what am I supposed to do? According to the support options I have to pay to open a support ticket. My account was not verified when it was disabled and I think I might be in some sort of deadlock in which the password reset won't work because I'm not verified, and the verification won't work because I can't log in.
I've never bought a single Apple product before and this has got to be the worst intro I could have imagined!Solved.
After about an hour on the phone with US support (who were very helpful I must say) it turns out that if you do not have an iTunes account with credit card information and a billing address, you are very much more likely to get your AppleId account disabled "for security reasons". This begs the question of course as to whose security we are talking about here! But there you go. If you are an Apple first-timer, get an iTunes account, fill in all your details, and you should be alright.
Thanks for everyone's suggestions. -
I'm getting the error message "Photos folder syncing has been disabled for the iPhone <my iPhone> because the folder "Pictures" cannot be found." lately.
Normally, all I do with photos is move them from my iPhone to my computer's (Windows 7) hard drive. I do this by connecting the iPhone with the cable, a box pops up on the screen asking me what I want to do, and I choose "Import pictures and videos". I've previously selected the "delete photos from the device after move" option (or however it's worded...), simply because I don't want this device to fill up with photos.
Lately, it has been importing the photos fine, but it won't delete them from the iPhone. This used to work just fine, now it doesn't work and I don't know what changed, if anything. In iTunes, I get the error message I list at the beginning of this message.
How do I fix this?Hi there scarbo59,
You mentioned that you are still able to import without issues, but you may still want to run through the troubleshooting steps outlined in the article below.
iOS: Unable to import photos to computer
-Griff W. -
My iPod Touch 4th gen is disabled for 22,000,000 minutes. I have looked all around the Apple support communities and I always find the same "solution", which is to put it into DFU or recovery mode and restore from a backup. Here's my problem: My computer crashed awhile back and I had to completely start over from scratch. So, unfortunately, a backup of my device no longer exists on this computer or any other computer.
Is there any way I can simply get rid of the disable? I remember my passcode, so that isn't a problem, all I need is to be able to input my passcode.
Or, do I absolutely have to restore to factory settings, and lose all my data?
By the way, I hope it does not matter, but I can't remember the IOS is was last updated with.
Thanks.Disabled
Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Wrong passcode results in red disabled screen
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: How to back up
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store -
ipod is disabled for 22,362,812 and will not let me restore it says there is a passwoed on this device and it needs to be removed. how do i get this device restored
Go into Recovery Mode per the instructions here.
Then, try the Restore. Everything except the password will be restored. Connect via cable to the computer that you use for sync. Be forewarned that it takes a long time. From iTunes, select the iPad/iPod and then select the Summary tab. Follow directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod. As before, say "yes." Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time. If that happens, only the apps that are part of the IOS will appear on your device. Simply choose manual "Sync" from the bottom right of iTunes.
Maybe you are looking for
-
Max L Import from Server data_file - Essbase 11.1.1.3
I got a problem setting the right path for importing data-files directly from a directory on the server (that is not under the "arborpath"). As I mentioned in the techref: http://download.oracle.com/docs/cd/E10530_01/doc/epm.931/html_esb_techref/maxl
-
RMAN Restore From External System
I have been asked to restore a database from a different company onto our system. I was given a CD with the RMAN backup that they took. It's the same Oracle 9i database and we are both on Windows 2003. I've never done a restore this way before. I wou
-
WebI Design Mode disabled when accessed from BI Launchpad Applications
I am running BI 4.1 and everything seems to be enabled when I log in to BI launchpad using administrator credentials but when I log in as a super user user, by default, Design mode and some of the other options are disabled. I have tried almost every
-
We have several accounts on the iMac, and a wireless Airport connection to the entertainment area. We would like to have iTunes continue playing our playlists even when one of the kids logs me out. Is there a way I can make iTunes immune for logging
-
CS3: Save For Web and keeping EXIF data???
I thought CS3 made a change to allow maintaining EXIF data within a file when using the Save For Web Option. I have Not found any option or preference for this. And when I use the Save For Web option, I loose the original time/date the images were ca