Alsa problem on boot

i am having this output on arch linux start. Sound work.
Restoring ALSA Levels [BUSY] Found hardware: "HDA-Intel" "Nvidia MCP77/78 HDMI" "HDA:10ec0662,15658217,00100101 HDA:10de0002,10de0101,0010
Sun Jan 29 16:23:45 2012: Hardware is initialized using a generic method
Sun Jan 29 16:23:45 2012: /usr/sbin/alsactl: set_control:1328: failed to obtain info for control #1 (No such file or directory)
Sun Jan 29 16:23:45 2012: /usr/sbin/alsactl: set_control:1328: failed to obtain info for control #2 (No such file or directory)
Sun Jan 29 16:23:45 2012: /usr/sbin/alsactl: set_control:1328: failed to obtain info for control #3 (No such file or directory)
Sun Jan 29 16:23:45 2012: No state is present for card Generic
Sun Jan 29 16:23:45 2012: Found hardware: "HDA-Intel" "ATI R6xx HDMI" "HDA:1002aa01,00aa0100,00100200" "0x174b" "0xaa60"
Sun Jan 29 16:23:45 2012: Hardware is initialized using a generic method
Sun Jan 29 16:23:45 2012: No state is present for card Generic
Sun Jan 29 16:23:45 2012: [FAIL]
Last edited by fpilee (2012-01-29 19:43:43)

RichAustin wrote:This might possibly be the same as http://www.linuxquestions.org/questions … nt-868335/ though that is for Slackware.
Found my answer in the wiki.
https://wiki.archlinux.org/index.php/Ad … chitecture
Last edited by doug piston (2012-01-31 18:36:31)

Similar Messages

P35Neo2 FIR and problem with booting

So I have problem with booting my compie. Compie try to boot to the part of start windows, after that in case of switch into graphicis mobo going down and restarting (WinXP SP3). I think, that problem is not in PSU, cos i have 800W XILENCE (+3,3V 28A, +5V 32A, 4x+12V 20A, -12V 0,5A, 5VSB 3A), Board P35 Neo2 FIR, E7200 proc, bios 1.9 (updated). I have 5 disk and use raid function in bios. Graphic Radeon HD3650, Memory Zeppelin 4x1GB KIT 800Mhz.
I start with change of PSU from 550W to 800W but it didnt work, previus PSU had (+3,3V 30A, +5V 32A, 2x+12V 18A, -12V 0,8A, 5VSB 3A),
i try change memory, but no efect.
After update bios there was standard warning about bad cheksum, after resave Bios settings it was gone, and compie boot after that.
Any idea?
Thanks

So my problem is solved...but my feeling of this is not good...
I updated BIOS from 1.9 to 1.10, reset Bios settings, after restart i pressed F2 for load standart settings and i changed in Bios only that i am using RAID and disable disket and it works...i boot my compie into windows without any problem...
So i try change another things in Bios and my compie hangs in continous resets without booting into windows...no BSOD only restart and restart...
After reseting Bios settings and again Load to Default it works...and run windows...
There was only one new thing ... screen flick for the second with new screen about checking NVRAM ....this screen was not visible before (and maybe this is the problem), cos if i change something in BIOS about clocking and power management and other ones, this screen is by booting missing...and compie not run in Windows...
Next thing what i see, that in CPU multiplication dont work multiplication 9,5 and proc used frequency 2400 (9x) (it is E7200 on 2533)
i hope that this bios 1.10 fixed my problems...and my opinion is that P35 Neo 2 FIR is not ideal board for E7200 proc...so i m looking for another proc...and maybe another board...

Bootcamp problem when booting win vista

hello guys
i have one small problem while booting with windows vist. i make a clean install with vista.
first i created bootcamp partition and then i boot with vista dvd and i formated the ''bootcamp'' partition and install vista. after restart and pressing the option key to select the vista boot the booting started with some errors. because is not possible to make screen shots on bootime i record a video and i uploaded to youtube so u can watch the errors.
does this happen on all macbooks with bootcamp/vista installation or the problem is on my macbook or the vista installation...?
http://www.youtube.com/watch?v=J7PrnQw-T_A
thanks

If Vista installed, and did an automatic restart after expanding and copying files to your hard drive, it should restart on its own into Vista until all the updates are applied. No need to use the Option key.
I didn't visit YouTube to try to see, other than what you have described.
As long as you formatted to NTFS and Vista accepted the partition (20-50GB is good number).
I would install Boot Camp from your OEM DVD from Apple either before doing any auto updates from Microsoft, or when it is all done. Either works. And add AV software like Norton AV 2009 (and yes, it is fine, unlike 2008 and before, and no need for any of the "Suites" with Vista, most get in the way and take over).
I have had trouble with Vista SP1 DVD though.

Problem with boot / new install system ond SSD

Hi guys,
I have fresh installed system on my new SSD. I use my old HDD as external usb drive.
I have problem with boot when I dont have connected HDD to usb.
My system boot only to console no to KDE. When I connect external HDD to usb and reboot system, system boot normally.
Logs after boot.
Feb 26 16:46:39 arch systemd[1]: Reached target Login Prompts.
Feb 26 16:46:39 arch systemd[1]: Starting K Display Manager...
Feb 26 16:46:39 arch systemd[1]: Started K Display Manager.
Feb 26 16:46:39 arch systemd-logind[231]: New seat seat0.
Feb 26 16:46:39 arch systemd[1]: Started Login Service.
Feb 26 16:46:40 arch kernel: microcode: CPU0 sig=0x1067a, pf=0x80, revision=0xa07
Feb 26 16:46:40 arch kernel: platform microcode: Direct firmware load failed with error -2
Feb 26 16:46:40 arch kernel: platform microcode: Falling back to user helper
Feb 26 16:46:40 arch kernel: random: nonblocking pool is initialized
Feb 26 16:46:40 arch kernel: uvcvideo: Found UVC 1.00 device CNF7129 (04f2:b071)
Feb 26 16:46:40 arch laptop-mode[271]: enabled, not active
Feb 26 16:46:40 arch kernel: input: CNF7129 as /devices/pci0000:00/0000:00:1a.7/usb3/3-3/3-3:1.0/input/input16
Feb 26 16:46:40 arch kernel: usbcore: registered new interface driver uvcvideo
Feb 26 16:46:40 arch kernel: USB Video Class driver (1.1.1)
Feb 26 16:46:40 arch systemd[1]: Started Wicd a wireless and wired network manager for Linux.
Feb 26 16:46:40 arch systemd[1]: Starting Network.
Feb 26 16:46:40 arch systemd[1]: Reached target Network.
Feb 26 16:46:40 arch systemd[1]: Starting OpenSSH Daemon...
Feb 26 16:46:40 arch systemd[1]: Started OpenSSH Daemon.
Feb 26 16:46:40 arch systemd[1]: Starting NoMachine Server daemon...
Feb 26 16:46:40 arch sshd[373]: Server listening on 0.0.0.0 port 22.
Feb 26 16:46:40 arch sshd[373]: Server listening on :: port 22.
Feb 26 16:46:40 arch mtp-probe[404]: checking bus 7, device 2: "/sys/devices/pci0000:00/0000:00:1d.1/usb7/7-2"
Feb 26 16:46:40 arch mtp-probe[404]: bus: 7, device: 2 was not an MTP device
Feb 26 16:46:40 arch kernel: hidraw: raw HID events driver (C) Jiri Kosina
Feb 26 16:46:40 arch kernel: usbcore: registered new interface driver usbhid
Feb 26 16:46:40 arch kernel: usbhid: USB HID core driver
Feb 26 16:46:40 arch systemd[1]: Starting Sound Card.
Feb 26 16:46:40 arch systemd[1]: Reached target Sound Card.
Feb 26 16:46:40 arch systemd-udevd[145]: renamed network interface eth0 to enp3s0
Feb 26 16:46:40 arch kernel: psmouse serio4: elantech: assuming hardware version 2 (with firmware version 0x040101)
Feb 26 16:46:40 arch kernel: psmouse serio4: elantech: Synaptics capabilities query result 0x7e, 0x13, 0x0d.
Feb 26 16:46:40 arch kernel: i915 0000:00:02.0: irq 45 for MSI/MSI-X
Feb 26 16:46:40 arch kernel: [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
Feb 26 16:46:40 arch kernel: [drm] Driver supports precise vblank timestamp query.
Feb 26 16:46:40 arch kernel: vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
Feb 26 16:46:40 arch kernel: iTCO_vendor_support: vendor-support=0
Feb 26 16:46:40 arch kernel: iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
Feb 26 16:46:40 arch kernel: iTCO_wdt: Found a ICH9M TCO device (Version=2, TCOBASE=0x0860)
Feb 26 16:46:40 arch kernel: iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
Feb 26 16:46:40 arch kernel: input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio4/input/input15
Feb 26 16:46:40 arch systemd-logind[231]: Watching system buttons on /dev/input/event2 (Lid Switch)
Feb 26 16:46:40 arch systemd-logind[231]: Watching system buttons on /dev/input/event1 (Sleep Button)
Feb 26 16:46:40 arch systemd-logind[231]: Watching system buttons on /dev/input/event3 (Power Button)
Feb 26 16:46:41 arch kernel: microcode: CPU1 sig=0x1067a, pf=0x80, revision=0xa07
Feb 26 16:46:41 arch kernel: platform microcode: Direct firmware load failed with error -2
Feb 26 16:46:41 arch kernel: platform microcode: Falling back to user helper
Feb 26 16:46:41 arch kernel: input: 2.4G Wireless Wireless Receiver as /devices/pci0000:00/0000:00:1d.1/usb7/7-2/7-2:1.0/input/input17
Feb 26 16:46:41 arch kernel: hid-generic 0003:1915:0F01.0001: input,hidraw0: USB HID v1.11 Keyboard [2.4G Wireless Wireless Receiver ] on usb-0000:00:1d.1-2/input0
Feb 26 16:46:41 arch kernel: input: 2.4G Wireless Wireless Receiver as /devices/pci0000:00/0000:00:1d.1/usb7/7-2/7-2:1.1/input/input18
Feb 26 16:46:41 arch kernel: hid-generic 0003:1915:0F01.0002: input,hidraw1: USB HID v1.11 Mouse [2.4G Wireless Wireless Receiver ] on usb-0000:00:1d.1-2/input1
Feb 26 16:46:41 arch kernel: BUG: unable to handle kernel NULL pointer dereference at (null)
Feb 26 16:46:41 arch kernel: IP: [<ffffffffa06c1317>] mousedev_open_device+0x77/0x100 [mousedev]
Feb 26 16:46:41 arch kernel: PGD b650b067 PUD b650a067 PMD 0
Feb 26 16:46:41 arch kernel: Oops: 0000 [#1] PREEMPT SMP
Feb 26 16:46:41 arch kernel: Modules linked in: mousedev(+) hid_generic iTCO_wdt iTCO_vendor_support ath9k(+) usbhid ath9k_common hid ath9k_hw ath uvcvideo mac80211 microcode(+) videobuf2_vmalloc videobuf2_memops videobuf2_core videodev media evdev psmouse serio_raw pcspkr cfg80211 lpc_ich i915(+) atl1e snd_hda_codec_via snd_hda_intel drm_kms_helper snd_hda_codec drm snd_hwdep snd_pcm snd_page_alloc i2c_algo_bit i2c_core snd_timer asus_laptop snd battery ac soundcore sparse_keymap acpi_cpufreq rfkill video input_polldev thermal intel_agp intel_gtt shpchp processor button ext4 crc16 mbcache jbd2 sr_mod cdrom sd_mod atkbd libps2 ahci libahci libata scsi_mod ehci_pci uhci_hcd ehci_hcd usbcore usb_common i8042 serio
Feb 26 16:46:41 arch kernel: CPU: 1 PID: 227 Comm: acpid Not tainted 3.13.5-1-ARCH #1
Feb 26 16:46:41 arch kernel: Hardware name: ASUSTeK Computer Inc. K50IJ /K50IJ , BIOS 217 12/04/2009
Feb 26 16:46:41 arch kernel: task: ffff88007ffeda00 ti: ffff8800b6516000 task.ti: ffff8800b6516000
Feb 26 16:46:41 arch kernel: RIP: 0010:[<ffffffffa06c1317>] [<ffffffffa06c1317>] mousedev_open_device+0x77/0x100 [mousedev]
Feb 26 16:46:41 arch kernel: RSP: 0018:ffff8800b6517c10 EFLAGS: 00010202
Feb 26 16:46:41 arch kernel: RAX: 0000000000000000 RBX: ffff8801390f5800 RCX: ffff8801390f5868
Feb 26 16:46:41 arch kernel: RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000246
Feb 26 16:46:41 arch kernel: RBP: ffff8800b6517c28 R08: 0000000000000000 R09: ffff88013b001600
Feb 26 16:46:41 arch kernel: R10: 0000000000000000 R11: 0000000000000004 R12: 0000000000000000
Feb 26 16:46:41 arch kernel: R13: ffff8801390f5880 R14: ffff8800b3287558 R15: ffff880138c8f600
Feb 26 16:46:41 arch kernel: FS: 00007f8de7e14700(0000) GS:ffff88013fd00000(0000) knlGS:0000000000000000
Feb 26 16:46:41 arch kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
Feb 26 16:46:41 arch kernel: CR2: 0000000000000000 CR3: 00000000b6507000 CR4: 00000000000407e0
Feb 26 16:46:41 arch kernel: Stack:
Feb 26 16:46:41 arch kernel: ffff88013926e400 ffff8801390f5800 ffff8801390f5878 ffff8800b6517c60
Feb 26 16:46:41 arch kernel: ffffffffa06c20cc ffff8801390f5b48 ffff8800b3287558 ffff880138c8f600
Feb 26 16:46:41 arch kernel: ffffffffa06c2e80 ffff880138c8f610 ffff8800b6517c98 ffffffff811a834f
Feb 26 16:46:41 arch kernel: Call Trace:
Feb 26 16:46:41 arch kernel: [<ffffffffa06c20cc>] mousedev_open+0xcc/0x150 [mousedev]
Feb 26 16:46:41 arch kernel: [<ffffffff811a834f>] chrdev_open+0x9f/0x1d0
Feb 26 16:46:41 arch kernel: [<ffffffff811a19e7>] do_dentry_open+0x1b7/0x2c0
Feb 26 16:46:41 arch kernel: [<ffffffff811aedc1>] ? __inode_permission+0x41/0xb0
Feb 26 16:46:41 arch kernel: [<ffffffff811a82b0>] ? cdev_put+0x30/0x30
Feb 26 16:46:41 arch kernel: [<ffffffff811a1e01>] finish_open+0x31/0x40
Feb 26 16:46:41 arch kernel: [<ffffffff811b1bf2>] do_last+0x572/0xe90
Feb 26 16:46:41 arch kernel: [<ffffffff811af0b6>] ? link_path_walk+0x236/0x8d0
Feb 26 16:46:41 arch kernel: [<ffffffff811b25cb>] path_openat+0xbb/0x6b0
Feb 26 16:46:41 arch kernel: [<ffffffff811b3cda>] do_filp_open+0x3a/0x90
Feb 26 16:46:41 arch kernel: [<ffffffff811c05c7>] ? __alloc_fd+0xa7/0x130
Feb 26 16:46:41 arch kernel: [<ffffffff811a2fd4>] do_sys_open+0x124/0x220
Feb 26 16:46:41 arch kernel: [<ffffffff811a30ee>] SyS_open+0x1e/0x20
Feb 26 16:46:41 arch kernel: [<ffffffff8152142d>] system_call_fastpath+0x1a/0x1f
Feb 26 16:46:41 arch kernel: Code: c0 6e e5 e0 5b 44 89 e0 41 5c 41 5d 5d c3 66 0f 1f 44 00 00 4c 89 ef 41 bc ed ff ff ff e8 a2 6e e5 e0 eb e0 48 8b 15 c9 21 00 00 <8b> 02 8d 48 01 85 c0 89 0a 75 c6 48 8b 05 37 1f 00 00 48 3d 60
Feb 26 16:46:41 arch kernel: RIP [<ffffffffa06c1317>] mousedev_open_device+0x77/0x100 [mousedev]
Feb 26 16:46:41 arch kernel: RSP <ffff8800b6517c10>
Feb 26 16:46:41 arch kernel: CR2: 0000000000000000
Feb 26 16:46:41 arch kernel: ---[ end trace 76aa0cbb67cf77f6 ]---
Feb 26 16:46:41 arch kernel: microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
Feb 26 16:46:41 arch systemd[1]: acpid.service: main process exited, code=killed, status=9/KILL
Feb 26 16:46:41 arch systemd[1]: Unit acpid.service entered failed state.
Feb 26 16:46:41 arch kernel: [drm] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
Feb 26 16:46:41 arch systemd[1]: Started Laptop Mode Tools.
Feb 26 16:46:41 arch nxserver[374]: NX> 161 Enabled service: nxserver.
Feb 26 16:46:42 arch kernel: fbcon: inteldrmfb (fb0) is primary device
Feb 26 16:46:42 arch kernel: ath: phy0: Enable LNA combining
Feb 26 16:46:42 arch kernel: ath: EEPROM regdomain: 0x60
Feb 26 16:46:42 arch kernel: ath: EEPROM indicates we should expect a direct regpair map
Feb 26 16:46:42 arch kernel: ath: Country alpha2 being used: 00
Feb 26 16:46:42 arch kernel: ath: Regpair used: 0x60
Feb 26 16:46:42 arch kernel: ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Feb 26 16:46:42 arch kernel: ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xffffc90011e80000, irq=17
Feb 26 16:46:42 arch systemd-udevd[139]: renamed network interface wlan0 to wlp2s0
Feb 26 16:46:42 arch kernel: Console: switching to colour frame buffer device 170x48
Feb 26 16:46:42 arch kernel: i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
Feb 26 16:46:42 arch kernel: i915 0000:00:02.0: registered panic notifier
Feb 26 16:46:42 arch kernel: ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
Feb 26 16:46:42 arch kernel: acpi device:38: registered as cooling_device2
Feb 26 16:46:42 arch kernel: input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input19
Feb 26 16:46:42 arch nxserver[374]: NX> 161 Enabled service: nxnode.
Feb 26 16:46:42 arch nxserver[374]: NX> 161 Enabled service: nxd.
Feb 26 16:46:42 arch systemd[1]: Started NoMachine Server daemon.
Feb 26 16:46:42 arch systemd[1]: Starting Multi-User System.
Feb 26 16:46:42 arch systemd[1]: Reached target Multi-User System.
Feb 26 16:46:42 arch systemd[1]: Starting Graphical Interface.
Feb 26 16:46:42 arch systemd[1]: Reached target Graphical Interface.
Feb 26 16:46:42 arch systemd[1]: Startup finished in 1.241s (kernel) + 3.231s (userspace) = 4.473s.
Feb 26 16:46:46 arch kernel: IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
Feb 26 16:46:48 arch kernel: IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
Feb 26 16:46:49 arch wicd[226]: dhcpcd[1383]: dhcpcd not running
Feb 26 16:46:49 arch dhcpcd[1383]: dhcpcd not running
Feb 26 16:46:49 arch kernel: IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
Feb 26 16:46:49 arch wicd[226]: Failed to connect to non-global ctrl_ifname: wlp2s0 error: No such file or directory
Feb 26 16:46:49 arch wicd[226]: dhcpcd[1389]: dhcpcd not running
Feb 26 16:46:49 arch dhcpcd[1389]: dhcpcd not running
Feb 26 16:46:49 arch kernel: IPv6: ADDRCONF(NETDEV_UP): enp3s0: link is not ready
Feb 26 16:46:49 arch wicd[226]: Failed to connect to non-global ctrl_ifname: enp3s0 error: No such file or directory
Feb 26 16:46:49 arch wicd[226]: dhcpcd[1397]: dhcpcd not running
Feb 26 16:46:49 arch dhcpcd[1397]: dhcpcd not running
Feb 26 16:46:49 arch kernel: IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready
Feb 26 16:46:49 arch wicd[226]: Failed to connect to non-global ctrl_ifname: wlp2s0 error: No such file or directory
Feb 26 16:46:51 arch systemd[1]: Starting Getty on tty2...
Feb 26 16:46:51 arch systemd[1]: Started Getty on tty2.
Feb 26 16:46:52 arch kernel: wlp2s0: authenticate with 08:86:3b:7f:86:08
Feb 26 16:46:52 arch kernel: wlp2s0: send auth to 08:86:3b:7f:86:08 (try 1/3)
Feb 26 16:46:52 arch kernel: wlp2s0: authenticated
Feb 26 16:46:52 arch kernel: ath9k 0000:02:00.0 wlp2s0: disabling HT/VHT due to WEP/TKIP use
Feb 26 16:46:52 arch kernel: wlp2s0: associate with 08:86:3b:7f:86:08 (try 1/3)
Feb 26 16:46:52 arch kernel: wlp2s0: RX AssocResp from 08:86:3b:7f:86:08 (capab=0x411 status=0 aid=4)
Feb 26 16:46:52 arch kernel: wlp2s0: associated
Feb 26 16:46:52 arch kernel: IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes ready
Feb 26 16:46:53 arch dhcpcd[1416]: version 6.2.1 starting
Feb 26 16:46:54 arch dhcpcd[1416]: DUID 00:01:00:01:1a:96:a5:70:1c:4b:d6:a2:1f:ad
Feb 26 16:46:54 arch dhcpcd[1416]: wlp2s0: IAID d6:a2:1f:ad
Feb 26 16:46:54 arch dhcpcd[1416]: wlp2s0: soliciting an IPv6 router
Feb 26 16:46:54 arch dhcpcd[1416]: wlp2s0: ipv6nd_sendrsprobe: sendmsg: Cannot assign requested address
Feb 26 16:46:54 arch dhcpcd[1416]: wlp2s0: rebinding lease of 192.168.2.3
Feb 26 16:46:55 arch kernel: type=1006 audit(1393429615.096:2): pid=1406 uid=0 old auid=4294967295 new auid=0 old ses=4294967295 new ses=1 res=1
Feb 26 16:46:55 arch login[1406]: pam_unix(login:session): session opened for user root by LOGIN(uid=0)
Feb 26 16:46:55 arch systemd[1]: Starting user-0.slice.
Feb 26 16:46:55 arch systemd[1]: Created slice user-0.slice.
Feb 26 16:46:55 arch systemd[1]: Starting User Manager for 0...
Feb 26 16:46:55 arch kernel: type=1006 audit(1393429615.106:3): pid=1477 uid=0 old auid=4294967295 new auid=0 old ses=4294967295 new ses=2 res=1
Feb 26 16:46:55 arch systemd[1]: Starting Session 1 of user root.
Feb 26 16:46:55 arch systemd[1]: Started Session 1 of user root.
Feb 26 16:46:55 arch systemd-logind[231]: New session 1 of user root.
Feb 26 16:46:55 arch systemd[1477]: pam_unix(systemd-user:session): session opened for user root by (uid=0)
Feb 26 16:46:55 arch login[1406]: ROOT LOGIN ON tty2
Feb 26 16:46:55 arch systemd[1477]: Failed to open private bus connection: Failed to connect to socket /run/user/0/dbus/user_bus_socket: No such file or directory
Feb 26 16:46:55 arch systemd[1477]: Mounted /sys/kernel/config.
Feb 26 16:46:55 arch systemd[1477]: Stopped target Sound Card.
Feb 26 16:46:55 arch systemd[1477]: Starting Default.
Feb 26 16:46:55 arch systemd[1477]: Reached target Default.
Feb 26 16:46:55 arch systemd[1477]: Startup finished in 7ms.
Feb 26 16:46:55 arch systemd[1]: Started User Manager for 0.
Feb 26 16:46:59 arch dhcpcd[1416]: wlp2s0: leased 192.168.2.3 for 283824000 seconds
Feb 26 16:46:59 arch dhcpcd[1416]: wlp2s0: adding route to 192.168.2.0/24
Feb 26 16:46:59 arch dhcpcd[1416]: wlp2s0: adding default route via 192.168.2.1
Feb 26 16:46:59 arch dhcpcd[1416]: forked to background, child pid 1522
Feb 26 16:47:10 arch kdm[238]: X server startup timeout, terminating
Feb 26 16:47:12 arch systemd-udevd[131]: worker [140] /devices/pci0000:00/0000:00:02.0 timeout; kill it
Feb 26 16:47:12 arch systemd-udevd[131]: seq 1255 '/devices/pci0000:00/0000:00:02.0' killed
Feb 26 16:47:12 arch systemd-udevd[131]: worker [146] /devices/platform/i8042/serio4/input/input15 timeout; kill it
Feb 26 16:47:12 arch systemd-udevd[131]: seq 1659 '/devices/platform/i8042/serio4/input/input15' killed
Feb 26 16:47:12 arch systemd-udevd[131]: worker [148] /devices/pci0000:00/0000:00:1d.1/usb7/7-2/7-2:1.1/input/input18 timeout; kill it
Feb 26 16:47:12 arch systemd-udevd[131]: seq 1679 '/devices/pci0000:00/0000:00:1d.1/usb7/7-2/7-2:1.1/input/input18' killed
Feb 26 16:47:12 arch kernel: [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
Feb 26 16:47:12 arch systemd-udevd[131]: worker [140] terminated by signal 9 (Killed)
Feb 26 16:47:12 arch systemd-udevd[131]: worker [148] terminated by signal 9 (Killed)
Feb 26 16:47:12 arch systemd[1]: Starting Load/Save Screen Backlight Brightness of acpi_video0...
Feb 26 16:47:12 arch systemd[1]: Started Load/Save Screen Backlight Brightness of acpi_video0.
Feb 26 16:47:12 arch kernel: input: failed to attach handler mousedev to device input15, error: -4
Feb 26 16:47:12 arch systemd-udevd[131]: worker [146] terminated by signal 9 (Killed)
Feb 26 16:47:12 arch kernel: input: failed to attach handler mousedev to device input18, error: -4
Feb 26 16:47:12 arch kernel: mousedev: PS/2 mouse device common for all mice
Feb 26 16:47:13 arch kdm[238]: X server for display :0 cannot be started, session disabled
Feb 26 16:48:56 arch kernel: usb 7-2: USB disconnect, device number 2
Feb 26 16:48:56 arch laptop-mode[1782]: Laptop mode
Feb 26 16:48:56 arch laptop-mode[1783]: enabled, not active
Feb 26 16:48:56 arch laptop-mode[1834]: Laptop mode
[xx@arch Desktop]$ uname -a
Linux arch 3.13.5-1-ARCH #1 SMP PREEMPT Sun Feb 23 00:25:24 CET 2014 x86_64 GNU/Linux
Could you please someone help me with this?
Thanks

Sorry to bump this, but I'm having the exact same error tonight on my HTPC, any chance you found out what the problem was ?
To make matters worse, it's not happening every single time, but maybe every 4 out of 5 boots (same kernel, no changes in between.)
I thought this was a kernel issue related to this:
https://lkml.org/lkml/2014/3/10/359
I've tried adding atkbd and psmouse to my mkinitcpio.conf MODULES section and rebuilt, but no change.
I changed the NVidia driver from nvidia-304xx to nvidia-full-beta-all ( 334.21 ) from AUR but it had the same error at the same place.
Here's the part from `dmesg` where it borks:
[ 3.229195] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:04.0-3/input2
[ 3.236312] input: Logitech Unifying Device. Wireless PID:400e as /devices/pci0000:00/0000:00:04.0/usb3/3-3/3-3:1.2/0003:046D:C52B.0003/input/input6
[ 3.237230] logitech-djdevice 0003:046D:C52B.0004: input,hidraw1: USB HID v1.11 Keyboard [Logitech Unifying Device. Wireless PID:400e] on usb-0000:00:04.0-3:1
[ 3.279150] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 3.280083] IP: [<ffffffffa1cbc317>] mousedev_open_device+0x77/0x100 [mousedev]
[ 3.280810] PGD c99ea067 PUD c9f4a067 PMD 0
[ 3.281266] Oops: 0000 [#1] PREEMPT SMP
[ 3.281668] Modules linked in: mousedev(+) nvidia(PO+) snd_hda_codec_realtek hid_logitech_dj usbhid hid usb_storage coretemp evdev microcode pcspkr serio_raw snd_hda_intel(+) snd_hda_codec shpchp snd_hwdep snd_pcm snd_page_alloc snd_timer snd soundcore i2c_nforce2 i2c_core wmi processor button r8169 mii ext4 crc16 mbcache jbd2 sd_mod ata_generic pata_acpi ahci libahci libata ohci_pci ohci_hcd ehci_pci ehci_hcd scsi_mod usbcore usb_common psmouse atkbd libps2 i8042 serio
[ 3.281820] CPU: 1 PID: 211 Comm: acpid Tainted: P O 3.13.6-1-ARCH #1
[ 3.281820] Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./MCP7A-ION, BIOS 080015 10/10/2009
[ 3.281820] task: ffff8800ca5c1b00 ti: ffff8800c97f0000 task.ti: ffff8800c97f0000
[ 3.281820] RIP: 0010:[<ffffffffa1cbc317>] [<ffffffffa1cbc317>] mousedev_open_device+0x77/0x100 [mousedev]
[ 3.281820] RSP: 0018:ffff8800c97f1c10 EFLAGS: 00010202
[ 3.281820] RAX: 0000000000000000 RBX: ffff8800c9987000 RCX: ffff8800c9987068
[ 3.281820] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000246
[ 3.281820] RBP: ffff8800c97f1c28 R08: 0000000000000000 R09: ffff8800cf401600
[ 3.281820] R10: 0000000000000000 R11: 0000000000000004 R12: 0000000000000000
[ 3.281820] R13: ffff8800c9987080 R14: ffff8800c0260058 R15: ffff8800c9f2a500
[ 3.281820] FS: 00007f8f12f05700(0000) GS:ffff8800cfa80000(0000) knlGS:0000000000000000
[ 3.281820] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 3.281820] CR2: 0000000000000000 CR3: 00000000ca93e000 CR4: 00000000000007e0
[ 3.281820] Stack:
[ 3.281820] ffff8800c9940000 ffff8800c9987000 ffff8800c9987078 ffff8800c97f1c60
[ 3.281820] ffffffffa1cbd0cc ffff8800c9987348 ffff8800c0260058 ffff8800c9f2a500
[ 3.281820] ffffffffa1cbde80 ffff8800c9f2a510 ffff8800c97f1c98 ffffffff811a83ef
[ 3.392372] Call Trace:
[ 3.398245] [<ffffffffa1cbd0cc>] mousedev_open+0xcc/0x150 [mousedev]
[ 3.398245] [<ffffffff811a83ef>] chrdev_open+0x9f/0x1d0
[ 3.398245] [<ffffffff811a1a87>] do_dentry_open+0x1b7/0x2c0
[ 3.398245] [<ffffffff811aee61>] ? __inode_permission+0x41/0xb0
[ 3.398245] [<ffffffff811a8350>] ? cdev_put+0x30/0x30
[ 3.398245] [<ffffffff811a1ea1>] finish_open+0x31/0x40
[ 3.398245] [<ffffffff811b1c92>] do_last+0x572/0xe90
[ 3.398245] [<ffffffff811af156>] ? link_path_walk+0x236/0x8d0
[ 3.398245] [<ffffffff811b266b>] path_openat+0xbb/0x6b0
[ 3.508083] random: nonblocking pool is initialized
[ 3.398245] [<ffffffff811b3d7a>] do_filp_open+0x3a/0x90
[ 3.398245] [<ffffffff811c0617>] ? __alloc_fd+0xa7/0x130
[ 3.398245] [<ffffffff811a3074>] do_sys_open+0x124/0x220
[ 3.398245] [<ffffffff811a318e>] SyS_open+0x1e/0x20
[ 3.398245] [<ffffffff815216ad>] system_call_fastpath+0x1a/0x1f
[ 3.556729] Code: 40 c1 85 df 5b 44 89 e0 41 5c 41 5d 5d c3 66 0f 1f 44 00 00 4c 89 ef 41 bc ed ff ff ff e8 22 c1 85 df eb e0 48 8b 15 c9 21 00 00 <8b> 02 8d 48 01 85 c0 89 0a 75 c6 48 8b 05 37 1f 00 00 48 3d 60
[ 3.556729] RIP [<ffffffffa1cbc317>] mousedev_open_device+0x77/0x100 [mousedev]
[ 3.556729] RSP <ffff8800c97f1c10>
[ 3.556729] CR2: 0000000000000000
[ 3.563412] ---[ end trace 590b482a8704c6ac ]---
[ 3.980300] input: HDA NVidia HDMI/DP,pcm=3 Phantom as /devices/pci0000:00/0000:00:08.0/sound/card0/input7
Here's the output on a good boot:
[ 3.415791] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:04.0-3/input2
[ 3.422256] input: Logitech Unifying Device. Wireless PID:400e as /devices/pci0000:00/0000:00:04.0/usb3/3-3/3-3:1.2/0003:046D:C52B.0003/input/input6
[ 3.422644] logitech-djdevice 0003:046D:C52B.0004: input,hidraw1: USB HID v1.11 Keyboard [Logitech Unifying Device. Wireless PID:400e] on usb-0000:00:04.0-3:1
[ 3.434861] mousedev: PS/2 mouse device common for all mice
[ 3.853639] input: HDA NVidia HDMI/DP,pcm=3 Phantom as /devices/pci0000:00/0000:00:08.0/sound/card0/input7
Here's my mkinitcpio.conf
: grep -v ^\# /etc/mkinitcpio.conf
MODULES="atkbd psmouse"
BINARIES=""
FILES=""
HOOKS="base udev autodetect modconf block filesystems keyboard fsck"
Last edited by corpdecker (2014-03-19 02:47:30)

Problems with Boot Camp - PLEASE HELP!

I'm having problems with Boot Camp. Here's what's happening. I ran Boot Camp Assistant, partitioning a 32GB BOOTCAMP drive. I insert my copy of XP and start the installation. My MBP restarts and boots into the Windows Setup. I let it run through the initial actions. I press ENTER to proceed, F8 to accept the license agreement, then when I get to the part where I should be able to select the Partition 3 BOOTCAMP drive (as it says in the Apple Boot Camp Manual) there is only a Partition 1 Unknown drive. It is the only drive to choose from and its a C: drive. I can't figure out why after I run boot camp the partitioned drive doesn't appear as an option in the windows installation. Please help!!!
Message was edited by: CarlConti08

Boot into Leo, start Disk Utility and you should see two partitions, your Leo partition and a Fat32 partition of 32GB at the end of the drive.
If not, boot camp didn't create it for some reason. If it is there then check it with DU and make sure its OK.
While your in there give it a name so you can easily identify it in your windows installer.
If there is no partition, create one using Disk Utility at the END if the drive. make sure you create it as a msdos (Fat32) partition and give it a name. The name cannot be more than 11 characters must be comprised of numbers and/or letters (no special characters).
Verify it before exiting DU.
Put in windows install disk, reboot - hold option key after the chime until you see the boot screen - select windows CD to begin install.
Don't forget to install Leo windows drivers after installing windows.
Kj

Help! problems with boot...

My system has worked fine for a week, but I have been unable to get the usb in front of my computer to work so I tried again today. I booted right after that but a strange noice came, sounded like electrisity and I got a bad CMOS message and the machine refused to boot. I tried to run flash recovery but for some reason both my floppy and keyboard does not seem to work/boot. I have tried another keyboard but nothing happends. I have tried to reset bios and to take out the cmos-battery but it made no change. any ideas of what I can do?

Quote
Originally posted by Jocko
Hi
The differance between this mobo and others, is the useage of the +12v, the CPU and mobo need at least 12amps to post. That leaves nothing for HDDs, Cds, fans, Graphic Card, etc. Your system will not be able to cope for long.
jocko
Taraquin these guys told me the same thing a few weeks ago about my PSU. My system was working fine, so I was like no that can't be right. but after some research on the net. I found that Jocko, SAB, and tiresmoke was dead on the money about the PSU.
From what I read and put together from several resources was that this mobo, CPU combo all by it's self pull heavily on the PSU. you add a Vid card, like an ATI 9800, a few cd roms and floppy and a few hard drives and use something different than the on board sound. What would be considered an average to good PSU just will not cut it with this system. after reading all of this I purchased an Antec true 550. you can believe what you like. but my system that i thought was having no problems, Now boots smoother, I have kept a check on my voltages they don't fluctuate like they did before. and the over performance of the system is better. I remember reading somewhere and I can't remember if it was here or else where that on the 12+ side you need a minimum of 24A for this system to operate well. DeMaxx

Problem during booting

hi guys
I installed Xp and then removed from my macbook.
Now there is problem in booting....
A black screen written " no booting device" comes during start of laptop...
Plz help

Hi and welcome to Discussions,
startup your MacBook while holding down the Option/Alt-key.
Choose your OSX volume to boot from.
Once in OSX goto System Preferences - Startup Volume and set your OSX volume as the default startup volume.
Restart and all should be well.
Hope it helps
Stefan

875P NEO FIS2R problems with booting at power-up

Having problems with booting at power-up.
Recently, with no apparent modification to system - at power up the system will often not boot. About 80% of time systems seems to go into a loop with CD/DVD drive light blinking a few times, then the floppy drive light comes on and can hear the FDD run – within 30 seconds or so, this process starts over again. Power switch LED is on and HDD LED is on (continuously). All fans are running (power supply fan, case fan, CPU fan and Intel Canterwood 875 fan ).
Monitor power on light is in power save mode (amber) when system does not boot. When boot is successful the monitor power light turns green immediately.
After pressing the reset button several times (varies between pressing reset button 1 time to 30 or more times) system will then boot OK or go into set up.
Once running there is no apparent problem.
This mainboard comes with D Bracket containing 2 USB 2.0 ports, and 4 diagnostics LEDs - when boot problem occurs the diagnostic LEDs, give a code that in the MSI mainboard manual states “Initializing Keyboard Controller” and diagnostic LEDs stays in this mode until via reset button provides a successful boot and start up.
Have reseated all connectors.
SYSTEM
Mainboard – MSI 875P Neo FIS2R (MSI 6758)
BIOS – AMI v1.8 (has not been updated)
CPU – Intel P4 2.6 GHz - system bus 800 MHz 512 KB L2 Cache
Memory – 1.5 gb (2 x 256 mb and 2 x 512mb)
Power Supply – Antec 380 watt
HDD – IED WD 160 GB and IED WD 40 GB
Video Card – ATI Radeon 9600 (128 RAM)
Operating System – MS Windows XP Pro (sp2)

Quote from: BOSSKILLER on 17-May-08, 03:34:12
Have you done >>Clear CMOS Guide<<?
Cleared CMOS - no change same problem. Also, re-seated all connectors at same time.
Quote from: Wonkanoby on 17-May-08, 09:06:54
have you just added the second wd drive
are they jumpered right
jumperless if alone on ide
jumpered master /slave if two on it
No, second 40GB HDD was installed months before this issue started and is jumpered as slave drive. Also, no other additional hardware installed for several months before issue.

Qosmio G30 problems when booting up

Hi - I hope someone can help.
My G30 has developed problems on boot up. When I switch on I hear the 'tune' and the drive light flashes but the screen stays black.
I've tried leaving it for up to 10 minutes but still nothing happens. If I hold 'FN' and press f5 it bursts into life and I then scroll the various screen options and it works fine. I am not too technically gifted so be gentle with me if you have any suggestions.
I only found out about the F5 because I thought it was a screen problem so I hooked up a separate screen to try to get some access to the drives.
Any thoughts - anyone?
Ron
Message was edited by: rocketronr6

Hi,
just a question: do you have a picture on your external screen? I couldnt in your posting figure out if yes or not.
You can try to remove memorymodules if possible, to test if its a memory issue. (Its often the problem that one module is faulty and the reason for no-boot)
Otherwise you should bring your lovely paperweight ;) to a local service partner for hardware checkup.
Would appreciate some feedback of your diagnosis progress :)
Greets

2006 iMac running OS10.7.5 with File Vault problem stops boot up?

2006 iMac running OS10.7.5 with File Vault problem stops boot up? Upon login this message appears: Your home folder, which is protected by File Vault, didn't open. it needs to be repaired.
It then asks: To repair the folder and continue logging in press OK. To log in as a different user, click Cancel login.
Clicking Ok
You are unable to log in to the user account "xxxxxxxxxxx" at this time.
Logging in to this account failed because an error occurred.
When I click cancel to log in as different user I get he following message: You are unable to log in to the user account "xxxxxxxxxxx" at this time.
Logging in to this account failed because an error occurred.

This condition is quite difficult and time-consuming to recover from. If the procedure suggested here is too complicated for your experience level, get help from someone more experienced. One option is to make a "Genius" appointment at an Apple Store. Legacy FileVault should not be used under OS X 10.7 or later.
If you have another user account with administrator status and can do so, log in to it and skip to Step 4.
Step 1
Boot into Recovery mode. The OS X Utilities screen will appear.
Step 2
Select
Utilities ▹ Terminal
from the menu bar. In the window that opens, type this:
res
Press the tab key. The partial command you typed will automatically be completed to this:
resetpassword
Press return. A Reset Password window opens. Select your boot volume if not already selected. Pull down the menu labeled Select the user account and select
System Administrator (root)
Follow the prompts to set a password. It's safest to choose a password that includes only the characters a-z, A-Z, and 0-9.
Select
 ▹ Restart
from the menu bar.
Step 3
At the login screen, click Other... Enter "root" (without the quotes) in the Name field, and enter the password you set in Step 4 in the Password field. You should now be logged in. Do nothing while logged in as root except as indicated below.
Open the Users & Groups preference pane. Create a new user and check the box marked
Allow user to administer this computer
Restart and log in as the new user.
Step 4
Load this web page in Safari.
Triple-click anywhere in the line below to select it:
sudo dscl . -delete users/fubar HomeDirectory
Copy the selected text to the Clipboard (command-C).
Launch the TextEdit application. Paste into the window (command-V). Substitute the short name of the FileVault user for the word "fubar".
Triple-click the edited line and again copy to the Clipboard.
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window. When prompted, enter the password of the user you're logged in as.
Step 5
You should now be able to log out and log in as the FileVault user. Your files still won't be available. FileVault is inactive.
Locate the disk image file named "fubar.sparsebundle" or "fubar.sparseimage" at the top level of your home folder. Again, substitute the short user name for "fubar".
Step 6
Try to open the file. If it won't open, try to repair it in Disk Utility. If it still won't open, restore it from your most recent backup. Keep trying older backups until you find one that works. If you don't have a backup, the data is lost, perhaps beyond any hope of recovery. There's a slight chance that you might be able to repair the disk image using an expensive third-party application called "Disk Warrior."
Step 7
Copy the files from the mounted disk image to the corresponding subfolders of your home folder. The Library folder is invisible in the Finder. Open it by holding down the option key and selecting
Go ▹ Library
from the Finder menu bar. Open the copy on the disk image by selecting
Go ▹ Go to Folder
and entering
/Volumes/fubar/Library
in the text box that opens. Again, substitute the correct name for "fubar".
Log out and log back in.
If there isn't enough disk space available to complete this step, unmount the disk image, copy the disk image file to an external storage device, delete the original, and try again.
Step 8
Back up all data, then delete the disk image file.
Step 9
Delete the user you created in Step 3, if applicable.
Step 10 (optional, but recommended)
Follow the instructions in this support article under the heading "Disable the root user."

Restore alsa settings at boot

Hello all,
I'm using alsa with pulse and set my alsa config through alsamixer. However each time I do so, the settings are not restored at boot up.
I added @alsa to my daemon array as well writing the alsa settings as root with "alsactl store".
Might it be that I use pulseaudio which overwrites or handles the settings differently?
Thanks for your advice.

I'm on the right track. Pulseaudio overwrites my alsa settings.
That means, when I run 'alsactl restore' manually after bootup, the correct settings are restored.
Now the question is, how can I restrict pulse to not behave like that?
This is my daemon array where I'm starting ALSA:
DAEMONS=(dbus !network !dhcdbd !networkmanager syslog-ng @acpid @alsa @wicd @bluetooth)
This is my openbox autostart.sh where I'm starting pulse:
adeskbar &
conky -q &
nitrogen --restore &
start-pulseaudio-x11 &
pnmixer &
fbxkb &
batti &
dropboxd &
blueman-applet &
And finally my inittab executing slim:
# /etc/inittab
# Runlevels:
# 0 Halt
# 1(S) Single-user
# 2 Not used
# 3 Multi-user
# 4 Not used
# 5 X11
# 6 Reboot
## Only one of the following two lines can be uncommented!
# Boot to console
id:5:initdefault:
# Boot to X11
#id:5:initdefault:
rc::sysinit:/etc/rc.sysinit
rs:S1:wait:/etc/rc.single
rm:2345:wait:/etc/rc.multi
rh:06:wait:/etc/rc.shutdown
su:S:wait:/sbin/sulogin -p
# -8 options fixes umlauts problem on login
c1:2345:respawn:/sbin/agetty -8 38400 tty1 linux
c2:2345:respawn:/sbin/agetty -8 38400 tty2 linux
c3:2345:respawn:/sbin/agetty -8 38400 tty3 linux
c4:2345:respawn:/sbin/agetty -8 38400 tty4 linux
c5:2345:respawn:/sbin/agetty -8 38400 tty5 linux
c6:2345:respawn:/sbin/agetty -8 38400 tty6 linux
ca::ctrlaltdel:/sbin/shutdown -t3 -r now
# Example lines for starting a login manager
#x:5:respawn:/bin/su robert -l -c "/bin/bash --login -c /usr/bin/startx >/dev/null 2>&1"
#x:5:respawn:/usr/sbin/gdm -nodaemon
#x:5:respawn:/usr/bin/kdm -nodaemon
x:5:respawn:/usr/bin/slim >& /dev/null
# End of file
Any ideas?

Apple Mini-DVI to VGA Adapter Problems in Boot Camp / Windows

I currently run Windows XP SP2 on my MacBook and recently purchased the Mini-DVI to VGA adapter so I could hook up the MacBook to an external projector, monitor, or TV to display what's on my Windows screen on the external device. However, when I connect it to any external device, it just goes nuts and sporadically continues to make the hardware connect and hardware disconnect sounds and doesn't allow for external output of the screen. Any suggestions...? Thanks!
Marc

I think I solved this problem.
It was in issue for me. My second monitor would only display the Windows XP screen when it was loading, then it would black out. I couldn't even move my mouse arrow to the other side. Then I fixed it, here's how (running Windows XP SP3):
1. Start > Control Panel > Appearance and Themes
2. Display
3. Go to tab "settings"
4. Double click the blue image with the "2" inside it. This is the second monitor, adjacent to your first, or primary, monitor. The blue box may be a desaturated, greyish blue, meaning that the monitor is disabled. Click it and it a box will pop up asking if you want to enable the monitor. Click OK, and then like magic, your monitor is resurected in it's Windows Glory! From there, adjust the resolution, and it should work perfectly.
This isn't a Boot Camp compatability issue, it's just a problem with the lack of familiarity that users of OS X have with using XP.
Have a nice day!
Message was edited by: BlakeTron
Message was edited by: BlakeTron

Problem dual booting Windows 8 and windows 7 G480

I bought new laptop g480 and it comes with windows 8 single language and I want to dual boot it with windows 7 Ultimate. So I create one partition 50 Gig using Minitool Partition Wizard, after that I boot into USB device ( I've bootable Windows 7 USB and already disable secure boot in BIOS). The process went fine until it ask me where to install the windows, so I choose the partition 50 Gig I created before but I get this message "Windows cannot be installed to this disk of the GPT partition style". Help me guys how to solve this problem, I've searched solution for this but non of them seems working for me. Step by step will be good for me. I hope to get quick reply for this because I've this problem since 2 days ago and never get solution .
Thank you.
Solved!
Go to Solution.

Hi @CharlyAR
I tried your solution before I posted the message here but it didn't work but then I give it try again and I manage to install the Windows 7 ultimate. Now my pc dual boot with windows 7 and windows 8 (windows 8 is the main OS).
p.s. This is important guys, if u want to make windows 7 bootable USB by following the tutorial on youtube it wont work if you pc/laptops is pure GPT (UEFI) because most of them using MBR to make the tutorial thats why it look easy and works for them, it's almost same but there's "add-on" with GPT mode. You have to make the windows 7 bootable USB in GPT (UEFI) mode or it wont let you install. I couldn't find tutorial for this GPT mode on youtube.
All I do is search my old DVD-RW and erase it and I follow the tutorial here, same what @CharlyAR told me
http://www.youtube.com/watch?v=z7rRsQGew28

Problems dual booting Windows Vista with Oracle Enterprise Linux 4

I tried dual booting my sony laptop which came pre installed with windows Vista,After a successful installation,windows Vista boots fine,but Oracle enterprise linux just stops booting at this point " Starting Udev...................................................(OK)
Initializing hardware....Storage network"
It's posibly a hardware compatibility problem but I dont know why I get stuck at this point.Can anyone help please?

hi,
r u getting this error while installing oel or after installation?
which version of oel u r installing?
u may get this error probably due to hard disk (usually sata) compatility with linux.
--Regards
Xaheer

Problems PXE booting Gen 2 Virtual Machines after Upgrading to Windows Server 2012 R2

My Current Setup:
I have two virtual machines set up with Hyper V on my Windows Server 2012 Server.
VM1: Configured to boot from an ISO file and runs Clonezilla server.
VM2: Configured to PXE boot using a legacy network adapter, and with a passthrough 250Gb hard disk.
These two VMs are connected to an external Virtual Switch, which allows physical machines to PXE boot to the Clonezilla server.
For the past few months I have been using this setup for two purposes:
1. To clone physical machines to the Clonezilla virtual server (as a backup).
2. To restore those image to the second VM if I find that need to get access to the files on the original image..
This has worked perfectly, except for the fact that the speed of the legacy network adapter on the second VM (which is required to PXE boot) is very slow. But I know this is because of the limitations in how the legacy adapter works...
Now my problem:
I found out that Gen 2 VMs allow you to PXE boot without having use a legacy network adapter, allowing me to image back to the VM faster. So I upgraded the Server to Server 2012 R2 . I then created the same two virtual machines on the R2 server. I can still
PXE boot the Gen 1 VM to the Clonezilla Server but I cannot get the Gen 2 VMs to PXE boot properly. They get an IP address from the Clonezilla Server but then just stop with the following screen. (note: I have disabled the Secure Boot).
Are Gen 2 VMs unable to pull down images from anything other than a WDS Server?

Hi J,
>>Unfortunately WDS is not a solution for us as it is dependent on the PC being part of a domain
If you would like to make the client not join to the domain, please check the box before “Do not join the client to a domain after an installation.” In addition, make sure not to set the client to the domain in the unattend file and do not prestage
the computer in AD. "
It is quoted from following thread :
https://social.technet.microsoft.com/Forums/windowsserver/en-US/1026c3a9-0a10-4a58-a48f-5391659a96c8/wds-set-unattend-file-for-workgroup?forum=winserversetup
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Alsa problem on boot

Similar Messages

Maybe you are looking for