Alternative IEEE drivers for the P6N SLI Platinum?

Long story short, now that I upgraded to Windows 7 (64bit), I can't stream video from my camcorder to my computer anymore, however it turns out that my camcorder also supports firewire, and wouldn't you know, so does my P6N! Or so I thought at least.
I buy a firewire cable and plug my camcorder into my comp... nothing. I figure the cable is bad so I buy a new one. I plug it in and... nothing. So I try to install some software from the website (The camcorder is a Sony Handycam DCR-HC20) and... nothing.
Sony's telling me to go bug windows, where as Windows is telling me to go bug Sony, however the only other problem I see hinted at when i search for solutions is that perhaps the drivers im using for my firewire ports are bad, so I need different ones. The thing is i don't know where to go to get reliable IEEE drivers, so I guess it'd be best to ask you guys.
Here's a rundown of my comp:
Windows 7 64bit (However chances are if any solution works for Windows Vista 64bit, it WILL work for Windows 7, so don't be shy about any solutions you may have)
P6N SLI Platinum
Handycam DCR-HC20
Oh yeah, i'm not sure which BIOS i'm using, however I don't recall ever flashing it so i would assume its the one that it was shipped with.
Thanks you for your time.

Quote from: DaLoona on 16-August-09, 21:54:16
Maybe a silly question, but did you connect the firewireconnection on your motherboard to the port on your case?
Hahaha, its all connected but i can imagine someone doing that, haha.
All kidding aside though, now that I think about it my computer only recognizes 2 firewire ports when there's 3 (one on my soundcard, 1 on the motherboard itself, and the extra one that I plugged in myself that came with the motherboard).
I guess I could fiddle with the added one but is there any reason why the firewire port on the actual motherboard itself wouldn't register my hardware being plugged in? I really wish I had another computer I could test it on, or at least something else that's firewire capable but I can't find anything, so the only other thing I can think of is the port on the camera is dead, which I SEVERELY doubt because its in perfect working order and hasn't been used that often in the few years that i've had it.

Similar Messages

What the most stable quality 4gb (2x2gb) memory for the P6n SLi Platinum?

Hi,
I'm looking for the most stable and very good quality 4gb of ram for the P6N sli platinum MB - what make does everyone recommend for this board?
I note that Kingston value ram is mentioned on the Approved list but I wanted something faster than the valueram?
Does anyone have either G.Skill or super talent and if so how do they work? Any other makes that you can recommend?
I know that there have been issue swith 4gb of ram for Xp/Vista 32 bit systems but from what I am reading hopefully the next bios should resolve this ...?
Thanks as this is the only item that's holding up my build now !

I don´t know whats the most stable 4GB solution is, I only can tell you, that I use Micron/Crucial mamory for years and never had any problems.
Actually in my new P6N-SLI Platinum are working 4 1GB dimms of crucial value ram ddr2-667 without problems.
There is a new bois version 1.22 for the platinum which solved the 4GB problem of earlier bios versions.
That was a bios problem and not a problem of the ram.
Manufacturer as Gskill on their GBHZ6400 modules and OCZ on their 1066 SLI modules are using the same Micron chips called D9GMH which are on my values.
They have great potential above the rated 667 speed. Cause i´m coming from germany and at the moment the prices of memory here are very cheap, a lot of people are thinking about upgrading their memory.
All what I read about here in germany G.Skill, Mushkin(very expensive), OCZ, A-data, TeamGroup are the most reliable rams
when it comes to high speeds and low latency modules.
At least I recommend the Crucial Ballistix ddr800 if you are not able to handle special settings in the motherboard bios.
And of course there are coming 2GB modules from most of the manufacturers, so you only need 2 modules for 4GB.
It´s your choice...
greetings from germany
gonzos-revenge

How to update a BIOS for a P6N SLI Platinum motherboard

I'm running Vista x64 with 4GB RAM. I'm having the same problem as everyone else that the OS runs slower with 4GB. I installed the Microsoft's hotfix and that didn't correct the problem. I downloaded the 1.5 BIOS drivers but I'm having trouble installing them. I created a boot disk by right clicking on the A: drive and selecting Format. Then I checked of System Disk or whatever it was called so I can boot off of it. It loads the A: prompt but it wont see any of my hard drives. I have two partitions; a C and a D. Since that didn't work I grabbed another floppy and installed the drivers on their.
Problem is that I don't understand how to Flash the BIOS. I run Afud408.exe from the command prompt and I get a list of options. I believe I selected the /p which did something, but then I rebooted and the BIOS is still v1.1 in the boot up screen. Can someone please help me? What do I need to type in the command prompt to get it to update?
Thanks.

Quote
Problem is that I don't understand how to Flash the BIOS. I run Afud408.exe from the command prompt and I get a list of options. I believe I selected the /p which did something, but then I rebooted and the BIOS is still v1.1 in the boot up screen. Can someone please help me? What do I need to type in the command prompt to get it to update?
In order to make this work you need to run the afud408.exe from a pure DOS command line (not a DOS box).
The correct command line needs to be:
afud408.exe BIOS-File name
Example:
afud408.exe A7350NMS.150
However, the best thing is to use the following tool, it will make the whole procedure a lot easier since it automatically prepares everything for you:
>>MSI Forum HQ USB flashing tool<<
It works with Vista 64bit as well. All you need is an USB Flash drive.
If you don't have an USB-Flash Drive you can also prepare a CD for flashing. Guides can be found here:
http://www.biosflash.com/e/bios-boot-cd.htm
http://www.biosflash.com/e/bios-boot-cd2.htm

MOVED: Had problems overclocking the P6N SLI Platinum?

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=125463.0

JACK NEW. IS THE BEST MAN TO HELP BE CAUSE HE HAD ONE HIMSELF, but anyway quad core, dual core etc makes no difference your memory and your cpu fsb makes a difference.
using dual core you can get up to 2.7GHz and using bios you can easily get up to 3.2 ghz without any water cooling. you can go up 3.4 ghz but everyone will tell you you need water cooling unless you want to lose your cpu

Speedfan config for P6N SLI Platinum

Would someone please upload their Speedfan config to the Speedfan website if they have configured SF for the P6N SLI Platinum mobo?
Or at least tell me what temp1, temp2 and temp3 and some of the voltages really are? WOuld love to know the NB and SB voltages as they do not seem to match what I have set in the BIOS. Vcore amtches but that is about it.
Also, I have my ram at 1.8V and VRAM always shows as 2.21V - any thoughts?
Thanks, Dave

Thanks. I like the concept of the Speedfan control mechanism and it was rated very well by this article - http://www.tomshardware.com/forum/221745-29-core-quad-temperature-guide. The free Everest has lots of stuff turned off so you have to purchase the Pro version and HWMonitor does not have any mechanism to rename the sensors. I also have TAT, CPU-Z and RealTemp but they are some incomplete.

P6N SLi platinum supports some yorkfields

Just in for the P6N SLi platinum users:
The Yorkfield Q9300 and Q9450 are supported on the mainbord with the current BIOS, 1.5 as well as the wolfdale E8190, E8200 and E8500
The Q9450 and E8400 are still under testing.
Look here:
http://global.msi.com.tw/index.php?func=prodcpusupport&prod_no=1140&maincat_no=1&cat2_no=170&cat3_no=#menu
Great news, altough the QX doesn't work, you now can still buy a new quad with nice speeds

When I read the site today it says than none of the 45nm CPU's such as the Q9300, 9450 etc are supported. Am I misreading this? In a separate thread I mentioned my dilemma. I have the P6NSLi Plat board and need a quad core CPU to run the application I need it for (golf simulator). Any options? Also need a Geforce GTX 285 or 295 card. That should work, correct?
Jeff

PSU support for P6N Sli Platinum

Hi,
This is my first post. I'm about to buy the P6N Sli Platinum mobo, and wonder if my current PSU would support it. It has the following specs:
Sirtec HPC 420-302 DF (420 Watt)
+ 5volt    40amp    220W
+ 3.3volt    30amp    220W
+ 12volt    18amp    218W
- 5volt    0.3amp    1.5W
- 12volt    0.8amp    10W
+ 5volt vsb    2amp    10W
It has a 20-pin ATX connector and additionally a 4-pin connector, I believe this is a +12V CPU-power connector, althought I'am not completely sure it's not an additional connector to connect to modern 24-pin motherboards.
The mobo-manual says:
"This connector allows you to connect an ATX 24-pin power supply.
You may use the 20-pin ATX power supply as you like. If you’d like
to use the 20-pin ATX power supply, please plug your power supply
along with pin 1 & pin 13 (refer to the image at the right hand).
There is also a foolproof design on pin 11, 12, 23 & 24 to avoid
wrong installation"
However, it also mentions the ATX12V power connector, which is 8-pin. Can I connect my 4 pin connector here? Anybody with the same motherboard?

Don't bother about the 300Watt but try to think in amperage (especially on the +12V-rail).
Example:
CPU: 7-8A
HDD: 2A (x2=4A)
Mainboard: 0.5A
3 fans: 0.5A
optical drive: 1A
Now if you take these numbers and add them together you will have about 13-14A not including your graphic card. Even if it would need only 50W (50W/12V~4A) you would already be at the very limit of the +12V-rail.
Even if these numbers above are a little to high and 11-12A seems more realistic (which I wouldn't count on) 6A would be left for your graphic card (72W) and you would still be at the limit of your power supply.
This is just a little example to illustrate the importance of paying attention to the +12V-rail. Maybe 18A is just enough to keep you system running, but I wouldn't bet on it. And to have the PSU working at its limit all the time is usually not a good idea. Remember that the maximum power of the +12V-rail will only be 18Ax12V=216W.

MSI P6N-SLI Platinum Multi-gpu enabling

Owners of the P6N SLI Platinum mobos. I'm having trouble Figuring out how to enable my two EVGA 256-P2-N636-AR GeForce 7950GT in SLI mode. The manual I have doesn't coincide with what my system is telling me. Anybody out there please shed some light on my predicament. thank you. >:(
my system is as follows
1: Intel Core 2 Duo E6700 Conroe 2.66GHz 4M shared L2 Cache
2: MSI P6N SLI Platinum LGA 775 NVIDIA nForce 650i SLI
3: Kingston HyperX 2GB (2 x 1GB) 240-Pin DDR2 SDRAM DDR2 800
4: 2 EVGA 256-P2-N636-AR GeForce 7950GT 256MB
5: system drive - WD Caviar 160GB 8MB SATA 3
6: backup drive - Seagate Barracuda 320GB 16MB SATA3
7: Windows Xp home sp2
8: PSU Antec Neo HE 500

read Moan Guide 1st and provide full system specification including PSU details(look over PSU sticker for them)
made sure JPW1 is connected,
install both VGAs:
made sure SLI Bridge is connected between them,
made sure addiction power cable is connected to each VGA,
connect monitor cable to the 1st VGA(located in the 1st PCI-E x16 slot)
go in BIOS and check for SLI related options, if exist ensure that they are configured property,
install latest chipset drivers for your board from Nvidia: http://www.nvidia.com/content/drivers/drivers.asp
install latest VGA drivers from Nvidia(94.24): http://www.nvidia.com/object/winxp_2k_94.24.html
type in "run":
rundll32.exe nvcpl.dll,LaunchMultiGpuApplet /* click OK or hit {ENTER} key when its done */
and Enable SLI from there, and config "OK":
to verify that SLI is functional correctly get a Everest:
http://www.lavalys.com/beta/everestultimate_build_1059_welo4kjhnxa.zip
navigate to GPU page and check it:
for SLI troubleshooting and guides look here:
http://www.hardforum.com/showthread.php?t=938853

[P6N SLI Platinum] black screen NO BOOT after D-bracket replug [RMA-SOLVED]

Quick setup specs;
P6N SLI Platinum
E6600 (box/stock 2400mhz basic)
2x 1Gb DDR2 6400 Gskill HZ
Sapphire ATI X1600Pro (PCI-e basic)
Aerocool Zero DBA 620W
(2 HDs sata, 2 Hds pata, 2 optical pata at first -all OK at first, disconnected after, so irrelevant here ,( )
(XP Pro clean new install from start)
I tried to check the forum old posts before trying to write that new one, but could not find any really related totally adequate posts so far (or i missed them, sorry if so, then -?). I could already find very useful informations on first aid usual 'rebooting' procedures to follow with minimum new boot configurations, d-bracket new LED signals etc. But so far no luck, all same, nothing better, nothing cured here for the stuation here. ,(( Also excuse my english if not perfect, i am not english either. ,(
VERY bad & sad problem here... ,(((( :
All was working perfectly great during 5 days.. the P6N SLI platinum install went GREAT initially (as normal, not a first pc built, all normally happening, so far so good, etc).... all hardwares compatible together at first (dedicated ATX 'full' 8x8 pins connector too for the cpu only for ex -all working perfect at first try. quick tensions 5V/12V under msi dual core control tool perfect too etc), was great easy going/ great strong ultra-stability feeling on the hardware side.. i was just now concentrating on the software side (no special BIOS tweaks even attempted so far, all on basics-normal e6600/ddr2 auto-settings, apart at the end ddr2 quick test -when problem occured- on 450(900?)Mhz at 2.1V, far far easy under its possible specs max anyway.. and had been working perfect for 3 days with that little ddr2 boost try -no time for special bios further tweakings now, etc), reinstalling and transfering/reorganizing slowly my necessary files/hds/softwares from old to new setup, no oc, nothing special tempted (i was planning oc, new cpu more suited fan/silver6 etc only for the end..), LAN file sharing setup done, Realtek audio setup test done, etc ; installation had been so far one of the quickest and problem free ever... explaining maybe also my fatal lack of cautioun for just (too much) 3 sec in the end after 5/- days of perfect working new ring going on.. ,((( :
At first, i also tried to immediately install the D-Bracket too to check possible hardware install problems -very useful feature i of course thought too..and wanted to try too, "in case of"..- (installing it from quick reading of the printed manual..with no colour pic coding inside..and quick error coming from there thereafter with an initial mismatch usb/jbd1 inverted plugs connections.. *both* having the exact same pins numbers and dispositions, beeing side by side on mainboard layout.. and so able to connect both headers indifferently.. so i did not see it immediately (( .. and no way to see it otherwise as such, anyway.. ,( ), just to be sure all was ok. I noticed that LED were of course, never lightning (not normal).. but as EVERYTHING else was working fine (GLAN, sound, etc etc).. i did not bother more than that -- error checking not necessary.
Till that fatal clumsy day i wanted suddenly to.. check the D-bracket too. ((((
All was working well, XP pro opened for hours as usual etc..
i had not yet totally finished to install the motherboard in the pc-case (always on desk, free in sight..)... so i could always see the connections on it. ... and i noticed that ... the colour headers codes were NOT matching (usb=yellow..).. i had just stupidly initially badly connected the D-Bracket jdb1/usb adjacent plugs (inverting them), so... And still, all had ever worked perfect.. except the D-Bracket, of course, was sending back no lights then, obviously.. so i did the fatal error.. confident all was stable enough and strong if even that initial plug error had had no consequences at all.. i did the fatal bad move to try to UNPLUG the D-Bracket connectors and put them back in right orders WITHOUT switching OFF the power supply so... like an hot USB plug, sort of, in a way. fatal error.. :( :( :(
As soon as i began to remove the usb/jdb1 connectors and put them back in normal order... the system suddenly SHUT DOWN ... no special bad noise, no special smell.. just sudden SHUT DOWN.
From there.. impossible ever to boot back again the so far perfectly working machine (((((((((((( , always same till now :
i switch on the power supply.. orange led appears on motherboard (ok)... i switch on the motherboard.. green led on motherboard appears (ok)... CPU fan begins (ok), video fan begins (ok) .... and... NOTHING.. total black video screen. no more even possibility to see the BIOS. :( total dead startup .. and the fans are going on eternally, blocked eternally in that inital startup with leds on too (no sudden shut down after a few seconds.. just.. nothing)... :(
Suprem irony.. the D-bracket LED seems to 'work' now.. "of course". Just the PC no more booting at all ^. Only thing is that only green LEDs are appearing, no red ones... simply the sequence, from start and never changing :
1. GREEN 2. GREEN
3. GREEN 4. (---) (not red, just nothing -?)
If i look in manual, it means "Testing RTC (real time clock)". I don't know exactly what it means *here*, but sounds to me it is the most basic initial first BIOS checking.. and BIOS can't be reached for even that so ; BIOS fried???? :( :(
I tried every 'standard' things recommanded usually here in older posts, for new boots recovery attempts thereafter in such 'boot errors' situations (clear cmos button pushed in every possible ways -quick, long, quick etc..-, removing little by little everything but the very minimal least energy taxing setup; keyboard, cpu, video, motherboard; 1 ddr2 nearest cpu slot.. point).. NOTHING. Worst, i tried to boot with one of those elements missing.. exact same D-Bracket lightning from start to.. eternally (123 GREEN 4-nothing). Even tried to remove the little (cmos?) KTS lithium battery for a few hours -that could work sometimes with the old already ultra-sensitive amd/nforce2 chipset bioses problems, so i tried there too-?-; same 3 green lights and fans running and nothing else happening from there.. ((
Always the same; total dead boot as above. black screen. no possible access to even bios panel. ,(((
So my desperate questions, now: of course, the origin is obvious here; all happened "by my fault" when i tried 'too quickly' to 'hot-plugging' replace correctly the D-BRACKET plugs *without* switching off the power supply... all shut down suddenly when i put back correctly the usb& jdb1 headers... :( ;
- do you think there could be any possible last HOPES to recover the situation that i had missed (a well known situation in such d-bracket handling 'common' (?) connection error, a simple trick to try i had missed ??)
- do you think i FRIED something in the process on the motherboard ?? :( :(
- do you think it is 'only' the BIOS (fried????) ?? :( :(
- do you think i could have fried a specifical external key component in the process (not necessarily motherboard) : ddr2 modules, cpu, video card????? :( :(
- is my only solution is to send the motherboard to RMA (no other ways now) ???
please, don't hesitate to give me any possible hints to try to avoid the RMA process.
can i avoid it, right now?
is that possible to fry an whole board just with such a D-Bracket 'hot plug switch' (on a so far perfectly working -light- setup - no oc, little video card, etc) ???? :( :(
That is the only C2D Intel/ddr2 motherboard i have here around. No possibility to test elements by elements for precise error checking (cpu, ddr2 modules, video card or powersupply).
Only things i could check so far are;
- the power supply (aerocool 620W zeroDBA) ;
i tested it back on my old amd xp-m nforce2 setup.. always working apparently. NOT 'fried' so, apparently. but no way of course to test for exemple the special 8x8 (or 8x4) Intel ATX cpu connector on old xp-m motherboard. But power supply NOt fried at least, apparently -?
- the video card.
no way for me to really test the pci-e card on other motherboard around but.. i tried a very old PCI VGA card.. that one works on old setup.. and on P6N, no effect, doesn't improve the situation. So, not sure the new pci-e video card isn't fried.. but a new video card doesn't correct the dead boot problem.. (
No way for me to test the ddr2 or CPU directly though.
Do you think DDR2 or CPU could have been fried in the process too ???
or just, as i fear anyway, 'simply', the motherboard BIOS fried -??? :-(
Really, thx for any suggestions..
if there could be an 'hidden' trick i did not try yet to try to recover the (initially working perfectly!!! (( ) setup, WITHOUT engaging the motherboard RMA process (at least 2 or 3 weeks lost here to wait the return..online store etc..)....
please, suggest me.. ,((
i am *really* very sad of that stupid clumsy idea to want to 'enable' the D-Bracket.. all was working great so far.. and i lost all with just that stupid idea to try an hot plug bracket reconnection without switching off the power supply it seems.. can it be possible,sigh?? all seemed so stable before that, that i.. just lost my usual cautious just 3 sec too long it seems... :-(
Thanks in advance
hoping post not too long too, but i tried to expose the situation as precisely as possible; first time i ever had such a problem with a motherboard/system install.. that is quiet ironical knowing it was also the best and quickest/easiest easy going new built i ever had so far too.. till then ,( .. and all came from the 'helper' d-bracket 'luxury second hand possible boot helper diagnostic tool' checking in the end too, here.. really hoping i can avoid an RMA process.. and no other hardware elements (apart the motherboard?) could have been damaged in the process ? ,(((

hi, thx a lot for the quick answer. sorry for the length indeed (i did not know exactly how to describe the situation.. without omitting any later possibly important details).
Alas, i already tried that many times in following interesting asnwers on similar problems in old posts here; did NOTHING. ,(
But after your post, i tried it again, and removed for the remaining *hours* (6/8h?) the cmos battery as suggested again *too* so -pushed again the clear cmos button etc when battery out, then when in again, then replugging the powersupply etc; NOTHING better alas too. always same, no boot, black screen, no bios. ,(
Problem always the same, to sum up, for clarity:
power supply on => orange motherboard led is lightning up, motherboard on => green motherboard led is lightning up, cpu/video/case fans are working up as normal and.. that's all. nothing else forever. black screen. no signal. not a single chance to get again the bios setup screen.
another detail i omitted, maybe; keyboard lights are all lightnng up too.. and stay blocked in that state too. tested with 2 different keyboards, same. to shut down the leds, fans etc, only one solution, shut down the power supply button directly, at that stage.
right now, i test on barebone minimal system as recommanded too;
cpu, 1 dimm (closest cpu slot), video, keyboard. all rest disconnected.
i of course tried to reset the cmos with the 'magical red button' many times before, with power supply cable plugged out, pushed the button trying almost every possible way so far (quick, long, long sequences, short sequences etc etc)... changed NOTHING so far -is that thing working?? ,(. and right now, same after hours with cmos battery removed too. ,(
the d-bracket leds are always (now it is correctly plugged..) :
123 GREEN 4 (nothing)
"Testing RTC (real time clock)"
another 'interesting' detail is that; those leds are appearing IMMEDIATELY after the motherboard is switched on, from start (green led appearing on P6N). and it is staying as such till the end. nothing else. i tried to connect also the case speaker ; no bips, no sound signals at all too.
I also remind the system was WORKING like a dream during 5 days *before* i had that sudden TOTAL boot problem.... AND i touched almost nothing in the bios too all along, for initial security reasons too.. (i was concentrating on the software installs anyway right now, NOT on the oc side..). The ddr2 quick little change i did was also the ONLY change i tempted to simply test quickly some setting i already saw working without problem with that P6N and that kind of ram.. and it was working without problem so far too, so.. all the time idem. And it had been perfectly working for 3 days as such untouched from there; no problems at all (those memory modules have been seen on that motherboard largely at those specs, why i did that quick test anyway.. far under their possible max -micron chips). it was even working so well i forgot to put the setting back as default after that quick ram test.. so much it was stable too (even if i had not time to do real memtest test on that one - i did for many hours with the initial automatical default settings too, to check the ram quality, was perfect for many hours, so ok too, no bad ram initially too-; was so stable for all my XP software installs operations etc.. that i forgot it thereafter, to be true..why it stayed like that till that moment (incidently).. but i preferred to mention it 'just in case' though, yes. i also did not push at all the dimm voltages in the process, it was always far inside the specs at 2.05V to be exact -usual for that ram too up to those numbers easy for it. i did not push the ram voltages either so..).
The problem ONLY appears when i wanted to unplug the *initially* badly connected D-bracket headers so (inverted headers.. but that caused NO problems either so far too for the system stability.. only the LEDs were of course not working so far..) : i did the error to NOT switch off the power supply. :(
*then* immediately the system shut down... and above situation appeared. ,(
BUT all was working perfect before.. ram setting included so. ,((
So my simple questions now too ;
- do you know what means *exactly* the d-bracket message 'Testing RTC" (123 GREEN, 4 nothing).. initial bios problem, isn't it?? other ways to recover it now?? ,((
- is it a WELL KNOWN PROBLEM when we try to disconnect and replug too hastily the d-bracket headers without switching off the power supply (*my* main erorr here, it seems :( :( ) ????
... and of course, do you think it could have *fried* another key component (cpu, ram -?? why i reminded the setting, just in case-?-, video card? .. ) with that d-bracket initial disconnection error ... ,(
as i said, i have no secondary c2d/ddr2 motherboard here : no way to test the cpu and ddr2 modules on another motherboard to be sure too here. :( i absolutely can't know if they have been damaged or not, here.. :( :(
any other idea for the motherboard itself though ??? ,(
once again, thx a lot for any suggestions and precisions on that problem (is that a COMMON well known problem with the d-bracket, when we unplug and replug it without extrem care like i did -my main inattention error it seems.. mainly because all was so stable before too.. ((( - without shutting down the power supply/system FIRST ???? can it be possible 'only' that shut down all the system??? (( )
thx in advance again +

P6N SLI Platinum Bios update in Vista x64

Just wondering how I update the bios for my P6N SLI Platinum in Vista x64? When I d/l the bios all the stuff is for 2000/me/xp. Why is there no vista support under anything?

Use the USB flashing tool developed here at the forums.
clickme>>MSI Forum HQ USB flashing tool!!!<<clickme

P6N SLI Platinum

I recently built a new computer with the P6N SLI Platinum mobo. The cpu (Intel Duo 2 Core E4300), vid card (evga 8800 GTS), memory (mushkin 2gbddr2 800), hd (Maxtor 320 gig SATA), and psu (apevia atx 500 watt) are all new. When the computer boots, all the fans and leds come on, but the monitor doesn't get a signal and the screen is black. I reseated the vid card and tried dvi/vga adaptor and a different monitor. The orange light and green light on the mobo are on. I used the pcie power 6 pin plug for the vid card. The 24 pin and 4 pin power connections to the mobo are ok. I haven't seen the bios because of the black screen. I also cleared the cmos and still no signal. I also tried an old Voodoo 2 pci vid card without the 2d pass through option and still no signal (don't know if that would work any way, but worth a try). The optical drives and the hd spin so they seem ok. I installed the D bracket with the lights to the usb header and jdb header. Should I see lights on this D bracket when the computer is booting? I don't see any and I don't get any beeps.

I now have no lights on the D bracket after clearing cmos again. I tried booting with one stick of ram and no change, then I tried booting with no ram and no change (no D bracket lights and no beeps). At this point, I have very little plugged into mobo - 1 hd, two optical drives, cpu, 2 fans and that's it.
Here are the ps specs:
Model
Brand APEVIA
Model ATX-CW500WP4
SPEC
Type ATX
Maximum Power 500W
Fans 2
PFC No
Main Connector 20 + 4Pin
Dual +12V Yes
PCI-E Connectors 1 x 6Pin
Power Good Signal 100-500ms
Hold-up Time >10ms at full load
Efficiency > 70% under max range load
Over Voltage Protection Yes
Overload Protection Yes
Input Voltage 115/230 V
Input Frequency Range 50/60 Hz
Input Current 12A @ 115AC, 6A @ 230AC
Output +3.3V@17A, +5V@25A, +12V1@16A, +12V2@18A, [email protected], [email protected], [email protected]
MTBF 100,000 Hours
Approvals UL, CSA, TUV, CE
Features
Connectors 1 x Main connector (20+4 pin)
1 x 12V (P4)
6 x peripheral
2 x SATA
1 x PCI-E
2 x Floppy

Question regarding P6N SLI Platinum CPU support?

I went to the product page list on the main MSI website and it lists the Kentsfield CPUs, but I happen to have an Intel Yorkfield Q9450 CPU. The question is, will this motherboard support that CPU or will it only support the ones listed on the product page?
I have the P6N SLI Platinum mainboard and recently got my hands on the Q9450 chip and would like to swap out CPUs with the Core 2 Duo E6700 that is in there now - anyone know if I can or not? The product page says that a CPU with a FSB of 1333 has to have that set manually in the BIOS, which I am willing to do, just need to know if this mainboard will even support the CPU I want to put into it.
Thanks!

Nuts, that's what I was afraid of...I was thinking that since the product page specifies a CPU with a FSB of 1333 (which the Q9450 has) it would be compatible.
Thanks for the answers - looks like I can't re-use my mobo, time for a new one.

P6N SLI Platinum (MS-7350) BIOS issue

I RMA'ed my P6N SLI Platinum MS-7350 and got back another identical board. However, this one has BIOS 2.7 in it. Bios 2.7 according to MSI page on this board is actually for the P6N SLI (also a MS-7350). The latest BIOS for the Platinum is 1.7. Im confused. Should I reflash it to 1.7 so that it has the proper BIOS instead of a BIOS from the P6N SLI not platinum? I know I have the platinum because the box says so AND the board has the copper heat piping across it unlike the MSI picture of the SLI (non-plat).

Quote from: TeachDJ on 05-January-10, 01:15:33
I have those: eSata, Firewire, and SPDIF port on this board yet, BIOS is currently flashed at 2.7 as mentioned. Thanks.
Then they clearly did return the Platinum board to you, as the P6N does not have those extras.
And (apparently) the v2.7 BIOS works with the Platinum as well as the plain P6N. Fascinating. Maybe you want to contact Tech Support about it, but if it's working--why are you concerned?
I'm interested because my P7N Platinum has a v1.3 BIOS, and (like your P6N) the lesser-capability board, the P7N, is up to BIOS v2.2. So I have wondered "Why is the simpler board getting more recent updates than the more sophisticated one?" But my system is working perfectly--it ain't broke so I don't need to fix it!

P6N SLI Platinum BIOS issue...

So I purchased an e8400 processor after the 1.6 BIOS update came out for my P6N SLI Platinum, got it yesterday. I put the processor in and it didn't work . I turned to Google to have the internet fix the issue, and it seems if I adjust some options in my BIOS, it may make the e8400 work. Two of the things it said to change were EIST and C1E. I went into my BIOS, and tried hitting F4 in the CPU menu to get C1E to show up, but it won't. The EIST option is no where to be found either...
Anyone else running into the same issue, or got a e8400 to work after changing stuff in the BIOS?
Thanks a lot!
EDIT: Forgot to post my system specs
Mobo: P6N SLI Platinum
CPU: Intel Pentium D 930
RAM 2GB (1GB x2) Patriot DDR 667 (PC 5300)
GPU: eVGA nVidia GeForce 8800GT
PSU: Thermaltake 500W

I used that bios, but on my regular p6n sli and got it to work. here is my topic on it
https://forum-en.msi.com/index.php?topic=115998.0
Dont clear the bios after you take out the old cpu or it wont work
I have been tinkering with it all day just to see what the actual problem is and it doesnt seem that it is the EIST OR C1E. from what I have done it seems that it is a problem with the voltages that keeps it from booting. If you change those with the other cpu in and then save and exit. Dont let it reboot, shut it off before it starts to boot up again and put the e8400 in

P6N SLI Platinum, no post (also!)

Hey guys.. I think I checked everything, but want to make sure.
Relatively new P6N (bought it, didn't have processor, stored it for the last 6 months) Platinum board. Finally got the CPU and Memory today (info below). Plugging it in, and I get.. nothing. No post, no beeps (with connected speaker), all lights on D-bracket *OFF*, all lights on keyboard *ON*. All fans come on as well. Both yellow/orange LED and the green LED between PCIs come on.
I slowly disconnected everything, and even ONLY with the board and CPU (no vid card and RAM, only front-panel and D-Bracket connected), still same result. Now, I'm thinking it MAY be the CPU, however, I would expect to still get ALL RED on the D-Bracket as per the manual. I don't have ready access to another 775 processor.
Items:
CPU - Intel E8400 (Wolfdale)
RAM - Corsair XMS2 (model "TWIN2X2048-6400C4") I've heard there was issues with this, is why I turned the board on without ANY RAM. Yes, it would not have posted, but I would/should have gotten a signal on the D-Bracket!
PSU - Antec NeoHE (430W, 3 12V rails, +3.3V 22A; +5V 14A; +12V 16A / rail; -12V 0.8A; +5Vsb 2.5A)
The only thing I have left to do is to try it outside the case. However, I'm posting here now in case anyone sees anything obvious I missed. I actually HOPE it's something I can do here - even if it NEEDS a bios update, I would still expect the D-Bracket to give me all reds ("The System will hang here if the CPU is damaged or not installed properly.") However, I'm afraid to turn the board on without a CPU. (Is that safe? Dangerous? I was iffy about not having the RAM in..)
Thanks all!
Mike.

Quote from: Jack the Newbie on 27-February-08, 04:18:29
The options usually change with the CPU that is installed.
Not sure, if the problem is only the current BIOS or if it is your CPU after all. It is hard to say at this point.
Eh, I'm hoping it's not the CPU. I can't verify if I get different options with the E8400 only because I get the same result (after updating to 1.5 and 1.6b3 BIOS revs as I had originally - everything powrs on, no D-LEDs (all off, NOT all red) and keyboard LEDs all on. So I don't even get the change to get into the BIOS to verify. :/ I'm sure that if I COULD, I could tweak the settings to at least get a stable system until I could use the processor at it's fullest, but.. as it is now, it's a nice lump of silicon.
Quote from: Jack the Newbie on 27-February-08, 04:18:29
This guy....
https://forum-en.msi.com/index.php?topic=114440.0
... was apparently able to get an E8400 working on a P6N SLI(-FI). It has the same model name & PCB Version as the P6N SLI Platinum.
I don't know, the best thing is probably to wait for a BIOS Update. Can you test you processor on another system that already supports Wolfdale CPUs?
I'm waiting. It's impressive - the P6N, even with the cheapest 1.6GHz Celeron processor is really nice. I won't have another LGA775 system to test with for another month. Hopefully, they'll have another beta or have released an update by then..
Thanks for your help, of course!
Mike.

Alternative IEEE drivers for the P6N SLI Platinum?

Similar Messages

Maybe you are looking for