Alum BT keyboard does not work after wake up - but BT trackpad does!

Here is my set up:
MBAir 2011 model (13", i7 4GB, Lion.. all up to date)
Desktop set up (same at work and home)
- Thunderbolt display
- Aluminum Bluetooth Keyboard
- Aluminum Bluetooth Trackpad
What I do:
- Plug in the sleeping mbair into my display via thunderbolt and power cable
- Wake up using external bluetooth trackpad
- computer wakes up and external trackpad is functional (it always works)
- 7/10 times the external keyboard will not connect to enter password to get into system
     - I have tried power button banging on it for a long time and does not work
     - open mbair and type password in and remove keyboard and repair and after several tried it will work
     - then I can close mbair and use external keyboard
     - painful to do this most days at home and work
What have I tried
- PRAM, SMC reset
- remove all BT entries - trash blutooth properties files and freshly add them back
- I have tried waking using keyboard as well and it does not work
Only think I have wanted to try and have not found out is, if keyboard can reset to factory.
Yes I also have the occasionaly wifi not connecting from sleep issue

Hello
Have you noticed this problem on factory settings or only on your Windows 7 installation? Maybe its just a driver or software issue
Make also sure that latest BIOS version is installed. Look on the Toshiba website for an update:
http://eu.computers.toshiba-europe.com > Support & Downloads > Download Drivers
Before you start the update, make sure that all programs are closed and you are logged in as Administrator.

Similar Messages

Satellite M70-394: WLan does not work after wake up from standby

Hi all....
I have a problem with my WLan connection and hope one of you may be able to help. Starting my computer from off there isn't a problem with the WIFI connection but if I put the computer into standby by closing the lid and then restarting it from there the light comes on briefly for wi fi but then goes off and the only way I can connect is through a cable.
Any suggestions would be gratefully appreciated.

Hi
I have read in the forum that some similar "Wlan standby" issues were fixed by BIOS update.
I think you should compare the BIOS version on the notebook with the BIOS which is available on the website. If there is a new update try to upgrade it
Be sure that you have chosen the right BIOS.

Flash player does not work after I installed it

Flash player does not work after I installed it

I'm using Mac Osx and my browser is Safari
Date: Wed, 5 Feb 2014 00:41:29 -0800
From: [email protected]
To: [email protected]
Subject: Flash player does not work after I installed
    Re: Flash player does not work after I installed it
    created by Mike M in Installing Flash Player - View the full discussion
This is a user-to-user forum, NOT 24/7 support. You're "lucky" I happen to be up at 1:40 am to answer you.
What OS are you using?
http://mmonlinedesigns.com/images/os.png
What browser?
http://mmonlinedesigns.com/images/browsers.png
     Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/6087541#6087541
     Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/6087541#6087541
     To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/6087541#6087541. In the Actions box on the right, click the Stop Email Notifications link.
           Start a new discussion in Installing Flash Player at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0.

My keyboard does not work after cleaning :-(

Hello, I have a MacBook Pro (bought in december 2009) an now the keyboard does not work after I cleaned it. This was on thursday and today it still does not work. Any ideas?

Chances are that you've shorted the terminals on the keyboard, and will need to be replaced… When the keyboard on unibody MacBook Pro's is replaced the whole 'top case' will be done, trackpad etc… Now generally it is highly unlikely that the Liquid submersion indicators will have been activated unless the cloth was saturated with water. Also unless you purchased the AppleCare protection plan your MacBook will be out of warranty and will require an out of warranty repair.
From knowledge out of warranty repair for a top case assembly it's £163 and a level 2 hardware repair is £28

Satellite A110-228 LAN does not work after hibernate

Well, subject says it all, really. The LAN (wired) network does not work after hibernate.
It seems it cannot find the DHCP server, so after a while it gets a 169.* address.
After a reboot, the network functions as usual (gets a IP address from the DHCP server)
Tried the usual things, disconnecting the cable, disabling the LAN device, battery or AC adapter, the behavior is reproducible.
The wireless network will be restored after a hibernate.
It needs a little help though (right click on the icon and "recover" or whatever it is called in English)
Any suggestions?
Wilm Boerhout

Hi guys
In the Toshiba HW setup which is placed in the control panel the options Wake-up on LAN and Built-in LAN should be enabled.
I think the options are disabled by default.
Furthermore the default setting for Wake on Settings is OS controlled. To use the Wake-up on LAN function under power off mode, in the device driver for the network card under the menu point Wake On Settings the Value Wake on Magic & Directed must be set.
Please check this how to enable WOL (first time use):
1. Go to [Start] -> [Control Panel] -> [Toshiba HWSetup] -> [LAN] tab
2. Enable Wake-up on LAN
3. Click [Apply]. System will request to reboot.
4. After the reboot go to [Start] -> [Control Panel] -> select [System]
5. On system properties dialog box select [Hardware] tab -> click [Device manager]
6. On Device manager dialog box select [Networking adapters] -> double click [Intel(R) PRO/100 VE Network Connection]
7. Go to [Advanced] tab -> select [Wake On Settings] property -> Select [Wake on Magic & Directed]
8. Press [OK] to close the dialog box.

Card slot does not work after update (14/10/2011)

Card slot does not work after yesterday update (14/10/2011)! It works with my SD card month ago, but now it dosn't!!!
MacBook Pro 13 OS ver. 10.6.8

Thanks for your suggestion. I downloaded OnyX and ran the cleaning function. After restarting, I opened Help and once again the first screen appeared fine. But again most of the links did not work, though those under the "What's New" heading did work. I might add that I had previously tried a variety of suggestions posted in another thread, which included deleting from the caches folder in Home>Library several files such as com.apple.helpui and help.plist in the Preferences folder. (As noted in my previous post this evening, I also created another user but that also did not have any effect.) Any other ideas? Thanks

HT1688 My Hot Spot does not work after update to 6.0.1. Service is with ATT. Apple says problem is with ATT, ATT says problem is with Apple. Anyone else having this problem?

My Hot Spot does not work after update to 6.0.1. Any suggestions?

Ok, I had the same issue, my phone is unlocked(iphone 5 with 6.1.3). So I went to the apple store and had it replaced. it worked good for a day and started doing the same thing. When the apple tech replaced my phone, he transfered my screen protector to the new one.
so I thought it was my sim card, I put in my sisters sim card from a different carrier and it did the same, so then I was like let me take off the screen protector, and that was it.
so guys, if you have a screen protector on your phone and it's doing "low signal", "No Service", "Searching", "Full bars cycle" then take off the screen protector. so far my phone is working normal.

Click to activate does not work after update

Click to activate plugin does not work after updating to version 23.0.1

hello Kamullia, if you have set click-to-play to true in about:config you can now go to the ''addons-manager > plugins'' section and set the permissions individually for each plugin type.

WiFi iPhone 4S does not work after update iOS 6.0

WiFi iPhone 4S does not work after update iOS 6.0

This sounds more like a hardware issue.
Have you checked that the dock connector port is not dirty?

My sound system does not work AFTER installing pc to tv wireless connection

my sound system does not work after installing hp pc to tv wireles device when I am using lap top for other purposes.

Hi,
You don’t install VS2010 on the client PC, then where did the Form Invoice not work? When you run it from another version of VS? Or when you run the application with application.exe?
Based on your description, one form works well, another form does not. I assume that two forms are in two different projects, then please check the .Net Framework used by the two projects. If they are different, you can use the
one used by the Form contact for Form Invoice.
Because this issue is a project issue, I recommend you to consult it on some application forum such as Windows Forms General forum for better support.
VS General Question forum mainly discusses
the usage of Visual Studio IDE such as
WPF & SL designer, Visual Studio Guidance Automation Toolkit, Developer Documentation and Help
System and Visual Studio Editor.
Thanks,
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

Apple TV does not work after trying to update software. Main light keeps blinking and on the screen shows itunes icon and a usb cable. What does that means?

My Apple TV does not work after trying to install the new software update. The main light keeps blinking rapidly and on the screen it shows the itunes icon and a USB cable. What does that mean?

The Apple TV is in recovery mode. Try to restore the Apple TV. Follow the link for instructions on the restore process.
http://support.apple.com/kb/HT4367

Hp Mini 110 1013tu Keyboard is Not working after upgrade to win 7

Hello need help on weird happenings to my keyboard..
Before i upgrade the Operating System From Windows XP to Windows 7 the Hp Mini 110 is working fine..
All keys on keyboard is working and touchpad is also working.
But after upgrading to windows 7 some keys on keyboard are not working like z,x,c,v, left ctrl and other more keys..
what do you think is the problem??
Hardware Issue? or Driver Issue?
please help thank you..

Hello @MysticDragon ,
Welcome to the HP Forums!
I understand some of the keys on your keyboard are not working after installing Windows 7.
I do not see any drivers available for your notebook for Windows 7 on the HP website, so their might be some compatibility issues as it's going to rely on Windows update to find current drivers. This doesn't mean it will not work, but I cannot say for sure that it will.
Try this:
1. Click Start.
2. Click Control Panel.
3. Click Clock, Language, and Region.
4. Click Region and Language.
5. Click the Keyboards and Languages tab.
6. Click Change keyboards...
7. On the General tab, make sure English (United States) - US is selected in the Default input language field.
8. Click on any other keyboards in the Installed services list.
9. Click Remove.
10. Repeat for all other non-English (United States) keyboards.
You may also want to try rolling back to Windows XP and see if the issue persists. It is possible the issue is coincidental and not the direct result of the update to Windows 7.
Let me know if this works!
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP.

IMessage does not work after upgrade to iOS 8.1.3 to my iPad 4

iMessage does not work after upgrade to iOS 8.1.3 on my iPad 4

I Fixed it by trying to sign in with a different ID and canceling when it asked For a password and then signed in with my ID and it works! No more error message. I got this idea from another discussion. Thank you for replying though.

HT3917 My apple wireless keyboard is not working after new batteries installed

My apple wireless keyboard is not working after new batteries installed.

Do you get a steady green light to say there is a connection. If not, are the batteries the right way round. Do you have a monitor to tell the batteries strength. Is there a reading. Are the batteries good quality ones, Duracell, Energiser or Apple rechargeables.

"F11 System Recovery" during boot does not work after Cloning hard drive.

Problem: “F11 System Recovery” during boot does not work after Cloning hard drive.
HP Envy m6-1125dx UEFI Notebook Computer with GPT hard drive.
Original Seagate Hard Disk GPT 700GB with Window 8.0_64 upgraded to Windows 8.1_64
Startup Menu (F11 System Menu works properly) only on original hard drive.
Following obtained from Disk Management & diskpart in Command Prompt.
GPT Disk <700GB>
Partition 1 WINRE NTFS Primary 235MB/400MB [Recovery]
Partition 2 EFI System FAT32 (LBA) Primary 108MB/260MB [System]
Partition 3 (NONE) Unformatted Primary 128MB/128MB [Reserve]
Partition 4 Main NTFS Primary 90GB/195GB [Primary “C”]
Partition 5 (NONE) NTFS Primary 372MB/450MB [Recovery]
Partition 6 Data NTFS Primary 7GB/475GB [Primary “E”]
Partition 7 NTFS Primary 26MB/350MB [Recovery]
Partition 8 Recovery NTFS Primary 24GB/26GB [Recovery “D”]
I have Cloned the original hard drive to a new HGST 1TB Hard Drive using four different methods (sector by sector):
Acronis True Image 2015
Acronis Backup for PC
AOMEI Backupper Professional
Macrium Reflect
Each time the cloning process completes successfully and has the same original partition arrangement. The computer works properly except when trying to use the “F11 System Menu” key during boot. It gives the following error message:
“Recovery
Your PC needs to be repaired
A required device isn’t connected or can’t be accessed.
Error code: 0xc0000225
You need to use the recovery tools on your installation media. If you don’t have any installation media (like a disc or USB device), contact your system administrator or PC manufacturer. “
Any suggestions why the F11 System Recovery does not work during boot and how to fix the problem would be appreciated. I have does various disk checking and file checking on both the original and new hard drive with no errors.
Thank you in advanced.

Hi,
How did you clone the HDD ? One-for-one or different method ?
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Alum BT keyboard does not work after wake up - but BT trackpad does!

Similar Messages

Maybe you are looking for