Always blinking amber

So, I'm missing something:
the Airport Express just keeps blinking amber.
My ibook G4 was willing to set up the new network, and says in the system settings that we are on the net, the ADSL Ethernet modem seems to think it is on the internet
but we cant seem to find the server when I open safari/check email, and that amber light keeps blinking.
The ethernet was working previously with an imac, who will be retiring,
I was thinking I've entered settings all wrong in the AE setup utility...
any help? enough information?
Cheers

Hi ABinSF.
There are several issues here. Firstly, your AE needs to be in your Airport Control Panel (ACP) in order for it to connect to the Internet. You do this by using the Airport Admin Utility located in the Utilities folder in your Applications folder. If you need further help on this get back to me.
Secondly, the Airport express will always flash amber if it is not connected to the internet. It MUST be connected to the Internet to flash green. For example, my AE is on my home network and is not connected to the Internet therefore is always flashes amber when I connect it to my iTunes library. It plays iTunes extremely well without the green light.
Hope this helps.
Roger
PowerBook 17/1.5 MHz Mac OS X (10.4.3)

Similar Messages

AExpress blinking amber/not always allowing PB to connect?

I have an airport express wth the cable modem hooked up directly to the ethernet port, and then the AExpress plugged into the wall. I am using a PB G4 to connect to the network, and using version 4.2 of Airport.
At first I was setting up my airport express in the closet, and the LED was blinking amber and wouldn't allow my PB to see it as an available network. So I brought it out of the closet in to the open and got my network set up beautifully. Then, I unplugged the airport express to put it in its permanent position, but this time after plugging it back in, I was able to long onto the network but can't get to the internet now and the LED is blinking amber again, no more solid green.
This second time around im positive it isn't interference, i brought it out into the open room with nothing around it, we dont have any 2.4 Ghz phones, no cordless phones at all actually.
Im stumped, I have no idea, I tried turning on interference robustness and even changing the channels in Airport Admin Utility, but to no avail.
Any ideas?

yes actually, the blinking amber means it does not have a valid IP address. make sure you have DHCP routing turned on in airpot admin. you might also try downgrading your firmware to version 6.1.1. this solved many problems for me.
http://www.apple.com/support/downloads/airportexpressfirmware611formacosx.html

MIFI4620LE Jetpack blinking amber light--does this mean the battery is bad? Should the unit operate without the battery installed if plugged in?

MIFI4620LE Jetpack blinking amber light--does this mean the battery is bad? Should the unit operate without the battery installed if plugged in?

The MIFI4620LE Jetpack does not work without a battery installed, even when connected to an external power supply.
I personally think that was a dumb design. I would think the unit would use more electricity when continually charging the battery than just powering the unit it's self, but that's the way Novatel made them.
If your Jetpack works with the battery installed and connected to an external power supply, but does not power on with power supply disconnected, I would say that the battery is defective or worn out.
You should be able to go to a nearby Verizon Store and have them either test the battery or put a new one in it to see if it works. Then you will know if you need to spend the $$ for a new battery. OR if you always use your Jetpack at home, or in your car, just use the old battery connect to a power supply or your cigarette lighter and save the cash.
As the Customer Support person stated, the slow blinking amber light is a normal state when the Jetpack is turned on and connected to Verizon's service.
I hope this solves your problem.

AX - blinking amber light

Three days ago, I was happily using my AX to access the internet. Then two days ago I disconnected the AX in order to use the ethernet cable for something else. But when I went to plug the cable back in, I started to get a blinking amber light. I've since did a hard reset to no avail -- still getting the light. Strangely, when I plug the ethernet cable into my computer directly, I'm able to surf the internet happily. Why doesn't the AX connect to the internet?
Thanks for your help in advance.

Always be sure to allow enough time for a complete power recycle of your network components when changing configurations ...
Modem/Router Power Recycling - Quick
o Power-off the DSL/Cable modem, Internet router, & computer(s); Wait at least 5 minutes.
o Power-on the DSL/Cable modem; Wait at least 5 minutes.
o Power-on the Internet router; Wait at least 5 minutes.
o Power-on the computer(s)
If this fails to get the modem to "recognize" the Internet router, then try the "Full" version.
Modem/Router Power ReCycling - Full
o Power-off the DSL/Cable modem, Internet router, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
o Power-on the DSL/Cable modem; Wait at least 30 minutes.
o Power-on the Internet router; Wait at least 5 minutes.
o Power-on the computer(s)

MSI GS70 : Battery Light Indicator Blinking Amber

Hey everyone, my MSI GS70's battery status light started blinking amber a few days ago. It blinks amber whenever the battery is fully charged with or without the adapter plugged-in. The battery is still working, and the blinking amber light goes away when the battery level drops from 100%.
When the battery level is at 99%, and I plug in the adapter, it starts charging the battery. I remember the battery doesn't get charged when it's at this level.
FYI I hardly use my laptop on battery, always using with the adapter plugged-in, so I'm very confused!!
Thanks.

try ec reset https://forum-en.msi.com/faq/article/how-to-reset-the-ec-embedded-controller

Time capsule blinking amber and my wireless network has vanished after factory reset

Hello,
I have an Apple Macbook aluminum body with a Motorola cable modem hooked up to the Time Capsule which acts as my router. After turning the power off in my home, the internet has not been working. The light on the TC was green, but I had no internet because Airport had a "self-assigned" IP address and may not be able to connect to the internet. Then, I decided to do a hard reset and restore my setting to factory. The light on the TC is blinking amber. When I go into Airport Utility, it gives me this message: "Airport Utility was unable to find any Airport wireless devices". On top of all this, when I did the hard reset, my wifi network is not on the list of Airport networks in my range. It has completely disappeared. I have all the wires connected properly to the router and TC. Please help, this scenario is very frustrating.

If you performed a factory default reset, the TC is now broadcasting a wireless network with a name like Apple Network xxxxxx, where the "x" could be either a letter or number.
You must first log on to this wireless network (there is no security or password) and establish a connection.
Then, if the TC was reset properly, you will be able to open AirPort Utility and re-configure the TC.
When you click Update to save your configuration settings, the TC will "dsiappear" from AirPort Utility. This is normal. Close AirPort Utility and wait for the TC to restart.
Then log on to the "new" wireless network that you named during the configuration.

HT1178 My Time Capsule is only blinking amber. My computer tried to backup but I don't know how to tell if it did in fact back up the data. How can I tell if it backed up and why doesn't the light show green?

Just purchased a Time Capsule. Had to call Comcast to disable the WIFI and have internet connection. The time capsule though blinks amber and the Airport Utility shows blinking amber light and has a red circle with the number 1 in it. After connecting, my computer tried doing a backup for the first time and it appeared that it was backing up and finished although I don't know how to check to make sure that it did backup. How do I check and shouldn't the light on the time capsule be blinking green and the airport utility show green?

TM will show it has done a backup.. Look at the info.. when was the backup completed??
If you want more details install the widget.
A1 here.
http://pondini.org/TM/Troubleshooting.html
The time capsule though blinks amber and the Airport Utility shows blinking amber light and has a red circle with the number 1 in it.
There is an error.. probably trivial.. firmware update, default password..
Open the airport utility and find out what the error is.
Simply click the TC and see status in the summary page.. it will list all the errors and what you should do.. fix or ignore them. ie this TC has an error.. default password.. I chose to ignore.. when I "fix" the problem the LED goes green.
Here is additional TC.. it is blinking amber with faults.
Click the fault. eg default password.
You can ignore or edit .. if you click edit it will take you to the full setup where you can change the settings.
I ignored my errors and now it is green..

Airport Express 801.11b/g and the neverending, unconfigurable blinking amber light

Gather round and let me tell you a tale. Once upon a time I bought an airport express 801.11b/g and I was very happy to use it for airtunes, extending a wi-fi network and the wireless printing capabilities. One day, it beagn flashing a scaaaary amber light. The base station stopped showing up in my airport utility 5.6 as well. The only way to get it to show up, was to hard reset it, and lose all the configurations I once enjoyed happily. After the hard reset, It would show up in the utility, and I would reconfigure it to do all its cool things it once did, and it would restart. But sadly, after restarting the blinking amber light came on a again. It would also not show up in the utility unless I hard reset it again, and the same thing happened over and over and over until I felt like pulling my hair out.
I decided to get another airport express a few months later, ultimately deciding that the unit must have just been defective. Bad luck. But - the second unit literally went through the SAME EXACT THING. Worked for a while, then onto the blinking amber light- hard reset- reconfigure-blinking amber light thing. Over and over and over. Just like the first one. The end.
So - either Im missing something totally fundamental or I had the misfortune of getting two defective units in a row. Both were bought used from different places, and worked "fine" for previous owners. Am I corrupting these things or what?
I have spent literally hours trying all the resets, configuring "workarounds" and nothing works. For both of them.
What do I do with these two devices? I don't need two shiny white paperweights.
Please advise,
Thanks.

Yes. It seems an integral part of the set up process though, you don't have to seperately configure the airport do you?
My wireless security is WPA/WPA2 Personal. When I go through the standard network set up, it automatically enters my wireless security settings. So it doesn't really seem to give an option to specifically set that option on the airport if that makes sense?
I did go through maunual mode to try that with the same result:
If I'm using the airports own network and connect to the wifi, no security, then I'm getting airtunes from my macbook. Of course this means it's plugged into my router via ethernet which isn't any use to me as I want it in my kitchen, and would rather not limit my apple devices to b/g when I have a decent N router, and would also mean running a huge ethernet cable across my house!
The seller has said it worked for him but he's not up to scratch on his tech, so if I'm sure it's malfunctioning he'll refund. Obviously this is great news and he seems like a very nice guy so I want to be certain it's not me malfunctioning before I send it back!
So in summary I have it functioning on it's OWN network:
Wireless mode: Create a wireless network
Wireless network name: Apple Network XXXXXX
etc
Once 'wireless mode' is switched from 'create a wireless network' to 'join a wireless network' I select my current WiFi, security and password, checked the TCP/IP settings all good. Select 'Update'. Get the warning that device and network will be temporarily unavailable am I sure I want to continue. Then it goes through the same as before, says it's succesful, restarts to flashing amber with no way of accessing it unless I hard reset.
Thanks for the help so far...

HT2497 I just purchased the 2TB TC and set it up on bridge mode to my att verse which is connected via ethernet cable. The TC is continually blinking amber and an error message states that a wireless network cannot be found but the uverse is functioning

I just purchased the 2TB TC and set it up on bridge mode to my att verse which is connected via ethernet cable. The TC is continually blinking amber and an error message states that a wireless network cannot be found but the uverse is functioning great. The network name I assigned to the TC is also not appearing among available networks. How do I remedy this, please?

What OS on the computer you are using to setup the TC?
Did you turn on ipv6 for wireless to link-local... this is essential for network access now??
Try power cycling the network.. start up in correct order.. uverse.. 2min wait.. TC.. 2min wait.. computer.
No luck factory reset and start over. Use ethernet cable as well to the computer to help it.
No luck I can show you manual method.

When I plug in apple tv the status light just blinks amber and nothing appears on the screen

When I plug in my apple tv (first gen) the status light just blinks amber and nothing appears on the screen. The status light never turns white and won't stops blinking amber. I've tried to over ride this with the remote, resetting it and trying to revert it to the factory settings. Is there a way to wake it up or is it a lost cause?

Welcome to the Apple Community.
The system looks like it's unable to start up, this could be software but more likely hardware, either way unless it will start up there is nothing a user can do to resolve this.

Airport extreme blinking amber light error when connecting to new modem

I have just bought and installed a new modem gateway. It is an Arris TG852G DOC 3.0 model with a built in WiFi router.
After connecting it and activating it through Comcast, I reset, then reconnected my airport extreme MD0331LL/A Model No. A1408 to the new Arris
modem, I am getting blinking amber lights on the base station. I have internet connectivity, but I am still getting an amber light. My wireless devices (ipad and iphones) all see the old network name and id and seem to work just fine.
When I scanned for my airport base station in my airport utility (version 5.6.1) to try to resolve the error message I get
a message stating that the Airport Utility is not detecting any airport devices.
I cannot reset the default settings as these buttons do not work within the Airport Utility.
I suspect interference between the built in router in the Arris and I understand I need to operate it in bridge mode. Can you please help me fix this.
The COMCAST people are extremely unhelpful, and stated that this is not their problem but a problem with my router
as they have provifded me internet connectivity through the modem and the issue is my problem.

Try connecting an Ethernet cable from your computer directly to one of the LAN <-> ports on the AirPort Extreme to see if AirPort Utility can detect the AirPort Extreme that way.
If yes, click on the AirPort Extreme and then click directly on the word Status (2nd line on the summary page)
A window will open to explain why the amber light is blinking
If the message indicates that you need to configure the AirPort in Bridge Mode......
Click the Internet icon at the top of the window
Click the Internet Connection tab just below
Change the setting for Connection Sharing to Off (Bridge Mode)
Click Update at the lower right of the window to save the new setting and restart the AirPort Extreme
You can disconnect the Ethernet cable that you were using to configure the AirPort Extreme now
It would be a good idea to power off both the Arris gateway and the AirPort Extreme now
Wait a minute
Start the Arris first, and let it run a full minute
Start the AirPort Extreme next the same way
You should be all set

I have an Airport Extreme Base Station and have recently upgraded to Mountain Lion. Now airport utility won't work with my base station so I bought a Time Capsule. For the life of me I can't make the substitution work and only see a blinking amber light.

I have an Airport Extreme Base Station and have recently upgraded to Mountain Lion. Now airport utility won't work with my base station so I bought a Time Capsule. For the life of me I can't make the substitution work and only see a blinking amber light. Can anyone who has made this change offer some advice?

apikoros wrote:
The Utility transferred all of the AE's settings, so I still have to change the password, which leaves me with only 2 other questions, I think:
1) I assume it's just a matter of using the Utility, entering a stronger password and checking for it to be remembered in Keychain Access. But do I have to change the password for each individual unit-- the TC, the Extreme and both Expresses-- or will changing it just for the TC alone work for the entire network?
Resetting the password you will need to do for each device... the utility cannot even see those old units.
So you will have to do it for each one.. think it through.. because as you change passwords the others will lose connection.. so start from the express which are wireless extending .. change those first.. and go back up the chain.. as each one changes it will drop off the network.. until you reach extreme and change that. Then you might need to reboot the whole network to get everything talking again. If something goes wrong.. just pluck that one out of the mix and plug in ethernet.. reset and redo the setup. That is my preferred method anyway.. do everything in isolation one by one. By ethernet and then nothing goes wrong.
2) Who's the treasonous SOB who spilled the beans to you about the ICBM in my back yard?!?
N.Korean hackers.
[Edit] Whoops-- one more question: I want to partition the TC's disk, but Disk Utility doesn't see it. What do I need to do?
You cannot partition a network disk. And apple provided no tools for it in the TC itself. You can pull the disk out and partition it but that voids your warranty. (although done with care who is to know).
Look at Q3 here.
http://pondini.org/TM/Time_Capsule.html
Mixing TM and data on the TC is worth planning carefully. They don't necessarily sit happily together.

Blinking amber in time capsule

Hi,
i am experiencing some trouble while configuring my time capsule for the 1st time.. the airport utility software locates the device but when i try to configure, it errors out with error code -4. i also tried to reset it but no luck.
strange thing is that i am able to access internet in my laptop (windows 7) through time capsule. the device is new and there is no password set for it.
also the led continuously blinks amber.

Is this a cable modem? It has to be off for at least 20min and sometimes much longer before it will give up the old settings. You might even need to power down the cable modem overnight.
Tell us exactly what broadband you have with what ISP and exact model of modem..
The new TC cannot be setup without using the latest airport utility 6.3.1 or 6.3.2 and you need Lion - Mavericks to use it.
The computer also needs to have ipv6 setup to local link on whatever you are connecting with, wireless or ethernet.

Airport express loses connection and blinks amber until restarted many times a day.

I have an AirPort Extreme as my,main router with a gen 1 airport express and 2 gen 2 express as range extenders to cover all 3 floors and outdoor area. I have an Insteon HUB connected to one 2nd generation express and an Insteon IP camera that is on the far edge of the WiFi coverage area. About 3-5 times daily, the express will blink amber and lose connection. I need to either restart the network from airport utility or just unplug and restart the specific express. This fixes the problem but only temporarily. Why does this occur? Is it due to the wireless camera losing connection? It seems to occur when I try to access the camera or devices thru the Insteon App. I have purchased the additional express thinking it was a poor connection to the other range extender but this has made no difference. I have been on tech support with Insteon for many hours,and they are unable to help. Any suggestions?

Hello Daniel Epps. Welcome to the Apple Discussions!
Every few minutes, it seems to temporarily lose its connection to the internet and start flashing amber until it reconnects. It's extremely annoying. Does anyone know why this is happening? Is it an airport problem, or a cable modem problem?
It could be either or neither ...
It is very possible that you may have some form of Wi-Fi interference in the immediate area that is preventing you from getting a good clean signal, and what I would check for first.
I suggest you perform a simple site survey, using utilities like the following to determine potential areas of interference, and then, try to either eliminate or significantly reduce them where possible:
o MacStumbler, or
o iStumbler

A blinking amber light doesn't necessarily mean that something is wrong.

Yesterday I set up a new AEBSn in bridge mode so that an attached hard disk could be shared by two Mac computers connecting to the AEBSn wirelessly pending inauguration of a new DSL connection.
Although the configuration worked perfectly, the amber light continually blinked because the AEBSn sensed that an Ethernet cable was unplugged even though the configuration did not call for any Ethernet connections.
Interestingly, the blinking amber light turned to solid green as soon as I added two network printers via Ethernet cables.

Just wanted to make sure you know that if the amber light is blinking, you can run the new Airport Utility and when the wireless devices appear on the left hand side of the page, anyone that is flasking amber will show up with a flashing amber light. If you double click on that device a new window will come up. On the summary page you'll see a line that says name of device and it will have a status light next to it that is the same as the status light on the equipment. In this case a flashing amber light. If you double click on the flashing symbol it will give you the reason for the flashing amber light.
In most cases at this point, the flashing amber light is usually because there was no security applied to the system.
If you opt, you can also turn off the amber light if you can live with the problem.

Always blinking amber

Similar Messages

Maybe you are looking for