ALWAYS NOISE from my guitar with SB ExtremeGamer + Front Panel (Fatal1ty I/O Drive)

No clue where to start from – anyway here goes – i got win7 64-bit and latest SB drivers (Beta after trying the older ones).
When i connect my guitar to my front Line 2/Mic 2 there is a LOT of hiss, wizz, and stuff - i tried from the line in (sound card from the back and mic) same result - i am trying to use some guitar effects, studio software.
I will lay all the steps I did to try to get a sound or GOOD sound from both Amplitube 3 and Guitar Rig 4 ; I was able to get the sound a BIT fair from amplitube Fender ONCE (I also tried Hendrix, AMpeg,Metal,X-gear) – that was when I connected to Line2/Mic2 Front Creative panel – other than that I can NEVER EVER GET A SOUND from those software. Any help would really be appreciated.
In a nutshell I have Sound Blaster X-FI Fatal1ty (ExtremeGamer XFi Pro Edition) with the front Fatal1ty I/O Drive that has all sorts of inputs (Digital + analog):
I beg you guys help me; I was thinking of purchasing stuff like the below if my SB won't work
• Behringer USB Audio Interfaces
• M-Audio USB Audio Interfaces
• Line 6 USB Audio Interfaces
• Even considered this chinese product: http://www.ebay.com/itm/ASIO-USB-Interf ... 3a63ff5158
I just wanna jam on my pc – don’t want to use my Digitech GSP 2101 limited edition nor my Korg PX5D in my bedroom – just gonna plug my ESP Horizon or my Fender Strat and have fun.
Please help me out in either fixing this crap or just point me to a good (better cheap) solution to finish from all the fizz, hiss,biss,wissss, tsss, etc… lol that comes out of all those apps
BTW I also installed Asio4All (also used Creative Asio and the DIRECT sound) and tried ALL the inputs outputs possible; 44.1k and 48k sampling (also tried that); messed around with control panel sounds (Playback / Recording), with Sound blaster own console and control panel.
I am sooo tired of it I just wanna blow up my whole PC
Tx a lot for any help that comes my way.
KicKer

Again another test i did: (BTW it is only left channel that is working or how does it go since u have wndows record left/right; Mix FL/FR/RL/RR/FC/LFE/RC or SL/RC or SR
using CREATIVE Asio (to use my front panel line 2/mic 2 connection) i tried:
1. Windows record left
2. windows record right
there is sound but bypassed from AT or GR (Clean sound)
now when i change only left channel to: Mix FL/FR/RL/RR/FC input is MAXED and nise is crazy even without connecting anything
finally choosing:
LFE
RC or SL
RC or SR
i get the clean BYPAssed sound (input signal is zero)
i set 00 MS and ms for Asio creative latency + tried 44 and 48 hz
Asio4all:
says not connected for all - when i go to its control panel and tick any WDM device list each one shows the yellow Unavailable/Beyond Logic mark
please please please help me

Similar Messages

  • Remove noise from Electric Guitar?

    Hello, I am using GarageBand with my electric guitar. I was able to make the sound come out of my Mac's speakers, but is there any way to make the sound from the guitar itself not be there?

    try to set monitoring active.

  • Display and interact with a vi front panel on remote C++ app

    Hello:
    I am new to LV and need a little advice.  I need to display a LabVIEW VI front panel in my C++ .Net application that users can interact with to view real-time spectrum data.  The C++ app (client) must reside on a separate computer(s) from the VI so that the client can connect from anywhere around the world and interact with the VI. 
    I am not sure about the basic architecture that should accompany a good solution.  We want to use TCP/IP but not DataSocket.  I do not have access to Measurement Studio but I do have access to LabVIEW Professional Development System v 8.2.  Can anyone provide suggestions on what I need to do in order to
    1.  Connect to my TCP server using my C++ client app - I have already written TCP client and server code which communicate but now I need to integrate LV
    2.  Get access to the VI sitting on that server
    3.  Send the VI front panel to the client for display
    4.  Allow the user to modify parameters on the front panel displayed on the C++ client, send those changes back to the server, and refresh the front panel displayed in the C++ client given the new parameters (I would like a real-time display of the spectrum to always be available)
    Is this possible?  Has anyone done this using C++ .NET in VS2005?  Are there examples I can mimic or references that will help direct me?  I have searched and searched through NI's help and found a lot of good stuff but I'm still feeling confused about the best way to utilize LV.
    Thank you in advance!

    One more question ... what if I could use Measurement Studio?  The documentation seems to indicate that it's easy to create network applications and therefore it would be easy for me to re-create our VI's front panel using Measurement Studio components in my C++ app and then simply connect those components to the networked hardware (TCP/IP or DataSocket) that could be located anywhere in the world.
    Depending on what components you are using in your LabVIEW panel, it is probably pretty easy to build a Measurment Studio application to look like a LV panel.
    Given that, you could use network shared variables to move data across the network, no TCP programming necessary -- I think that this is pretty easy to do, but I don't know the specifics about variable programming in that environment.  Also, you will probably need to add some smarts to the server side to make sure that it is reading to and writing from variables in an appropriate manner.
    Question: why can't you just use LabVIEW for the client application also?

  • No sound from headphone on X-Fi Platinum Front Panel

    Hey,
    i just built it a X-Fi Platinum installed the drivers and checked if everything works. My Problem is i dont get any sound out of the headphone jack at the Front Panel.
    Headphone detection ist working as is the remote control.
    Any ideas what could cause this? I need that 2nd audio output.

    i have the exact same problem with vista!!!no sound from the front panel of x-fi platinum!i don't know what to do!

  • How can I stop and restart a .vi with a single front panel button?

    Hey guys, a newbie here.
    I have a .vi with a stacked sequence. The first few frames are hardware initialization and settings (LIN master node) and the data the hardware should transmit (frame response table). In the next frame there's a loop in which the hardware sends and recieves data (LIN monitor). If I want to change the initialization, settings or data values, I have to stop the .vi and restart it. I was wondering if there is a simple way of doing this with a single click (a button on the front panel).
    An alternative would be to put another loop outiside the whole stacked sequence and then run it a single time with a push of a button (the inner loop should let the outer one restart), is that possible?
    I hope I made any sense. Thanks for any suggestions.
    Tomaz
    Solved!
    Go to Solution.

    Ideally, redoing the code with a state machine would be the best way to go, if only so that you can add this powerful tool to your toolbox. That being said, wrapping your existing code in a while loop, with its own stop button to stop the program, will work if executing the entire sequence is ok. Where you might run into problems with this is if there is a step in the sequence that shouldn't be executed again, then it would require wrapping that sequence frame's code in a case statement that executes only the first time through. If you have the time, learning how to use a state machine would be a real benefit, really taking your LabVIEW knowledge to the next step, if you pardon the pun.
    Putnam
    Certified LabVIEW Developer
    Senior Test Engineer
    Currently using LV 6.1-LabVIEW 2012, RT8.5
    LabVIEW Champion

  • Help with USB for front Panel on case!!

    Ive got the K7N2G mobo and Im trying to connect to JBT1 for Front USB.. it mentions bluetooth connection but it also talks about it being for USB.. Pleas help.. am i missing a bios setting?  How else can i get the front sub ports to work on my case?

    You got mixed up, JBT1 shares a USB connection with a USB header. If you use JBT1 for bluetooth you must give up one of the USB ports but you can't use JBT1 for USB.
    And I moved you over to the nvidia/sis section since you posted in the VIA section.

  • Menu with submenu in front panel

    Hi,
    I have some Enum controls in my code where each of them includes 3 items. I'm trying to build a drop down menu in the front panel and include all these controls. Obviously the items in each control would be sub-items in this situation. Any suggestions to do this?
    Note that I don't want to use Run-time menu. It makes a lot of problems when building the application file. 
    Thanks

    hi,
    I think you should use .Net Toolstrip. I've created a toolkit for that so it is very easy to use. Link: Here
    In the example you can see how to use toolstrip as a replacement of LV RTM but It can be used as an individual control and I think this could solve your problem.
    Machine Vision Techniques & LabVIEW Solutions - The solution is Yours!

  • Equium A100-147 - Clicking noises from the HDD

    For a while I have had clicking noises from the HDD and when the laptop failed I assumed the drive had packed up but when trying a replacement nothing happens. I get a blue light for battery and a (faint) blue light for DC supply but nothing for power or disk. However, when I connected an external drive yesterday it booted fine and when I disconnected it the laptop continued working from the internal drive. But again this morning it is dead and cannot boot. I have read that the BIOS can stop recognising the drive or maybe the settings are not being saved when it is turned off. Could it be the motherboard battery ?

    If I understand you right your notebook is death now, right?
    I really don't know what to do. Remove the battery and HDD and try to start notebook. if the same happen again it is time for new notebook.
    I don't think repair is best option because it can be pretty expensive. Satellite A100 is pretty old notebook and you can sell it on eBay. Someone will need it for replacement parts.
    Maybe my opinion sounds stupid but I don't know if you have time to search for new parts. I cannot say for sure but there must be some serious problem when you cannot even enter BIOS settings or see anything on the screen.

  • LV2011 problem with several front panels

    Hello,
                 There is a bug in my software and I don't know it is common to every one or not. This not to be worry, I will notify you anyway. When I open only one front panel and one block diagram which having a program to communicate with a serial device. In this case, if I choose the VISA resource name, it obviously takes some time to popup the USB and after it show the port and front panel will stay in front you until you choose the device. Here, every thing is fine but when I open several front panels and working on only with serial program front panel to choose the serial device in VISA resource name. Then after some time, it took me to another front panel. I have seen this problem several times in past two months. More, even when I am decorating the front panel and front panel took some time after pushing some controls and switched another front panel.
    Is this bug? Or I common for every one.
    Using labVIEW 2011.

    I am certainly using labVIEW from two months. So, I did not use MAX in my past time. I only used one time to check my USB 6008 device but this is off topic here. I will tell you down here.
    Suppose, If I open multiple VI's and I am only working with one VI that can communicate with my SERIAL device and the rest of the VI's(Block diagram and front panel) are rested. This case, if I click the drop downlist of "VISA resource name" of SERIAL VI, then it took some time(200ms or 100 ms, just it is a guess) to populate and it is switched to another front panel which were opened and rested before. Again, I need to come to my serial front panel again to select the COM port. This is one case.
    If don't have any other VI's not opened than this serial Vi. Then it stays on the same front panel.
    Is this bug came with labVIEW or  is it common?

  • Can i place controls from the properties dialog of an express vi on the front panel?

    I'm using the spectral measurements express vi in my vi and I'd like to put the "window" and "number of averages" controls from the properties dialog on the front panel. However, there are not outputs on the express vi icon for these parameters. Can I place controls for these on the front panel somehow or do I always have to go into the block diagram and open the properties dialog to change the values?

    The way to do this is to right click on the express VI and select Open Front Panel. This will convert it to a standard subVI. then go into the subVI and replace the Spectrum Averaging and Spectrum Window constants to front panel controls by right click on them. Right click the icon and select Show Connector. Wire the new controls to a free terminal on the connector. You may have to add additional terminals if there aren't any available to wire to the new controls.

  • Hiding front panel with built applications

    I've seen and used the techniques to run a VI with a hidden front panel. I have the VI open a reference to itself and it works as expected. However when I build my code into an application, it no longer works. Watching Task Manager I see the application quit when the panel becomes hidden. I've even tried building the window-less.zip example I downloaded from the NI website. It worked in VI form but not in EXE form. Anyone have any suggestions?
    Andy Brown
    Averna

    Andy,
    I ran into this problem back in LabVIEW 5.1 when I was developing a game in LabVIEW. I had an introductory screen that allowed the user to run the tutorial or play the game, and upon selection I hid the introductory screen and displayed the panel of the appropriate subVI (tutorial or game). Unfortunately when I built an executable, it would end once I chose to run a subVI, and I later found out that this is because closing the front panel of an executable essentially closes its reference. My workaround was to use LabVIEW 6i and the new tab control to keep all of my front panel operations in the same VI, and programmatically switch between the tabs in order to display different screens (like tutorial, enter info screens, the actual game, etc.)
    I hope this
    suggestion helps. There may be a way to bypass the problem with closing EXEs once their front panels are gone, but I do not know of one.
    Good luck with your application, and have a pleasant day.
    Sincerely,
    Darren Nattinger
    Applications Engineer
    National Instruments
    Darren Nattinger, CLA
    LabVIEW Artisan and Nugget Penman

  • Audigy 2 card with Audigy Front Panel not worki

    I've just bought a used audigy 2 card with an audigy front panel. I have installed everything and have sound from the card to my speakers.
    The front panel has a blinking light on the optical out and when I plug headphones into the panel, I can hear static and control the volume of the static from the knob on the panel.
    I can't hear anything else through the headphone jack and can't get any input signal using the line 2 input on the front panel.
    Connections and drivers appear to be OK, am I missing something......
    Thanks,Dave.

    David,
    If you go into the surround mixer or Windows mixer do you see a listing for the front panel inputs (line in2/mic in2, Aux 2, etc)? If so, are any of them muted? If you go to start/programs/Creative/SB Audigy/Audio HQ/Device Settings, do you show a headphone tab? If so what options are enabled in there?
    Double check your ribbon cable connection and maybe even swap sides of the cable.
    Jeremy

  • I am having trouble stopping a sub VI from the front panel of my main VI.

    Whenever I try to stop my sub VI from the main panel i cannot get it to work. It has entered the value of the switch from the main VI and does not update it within the sub VI after it has started the sub VI and hence does not look for a changed value on the switch. Is there any way that I can get the sub VI to check the state of the switch on the Main VI on each loop?
    Thanks
    Ross H

    Hi,
    I am including 3 VI programs, here main vi controls the sub vi, i mean sub vi can be stopped either from main vi or from stop button put on its front panel. Also main vi still works incase sub vi is running.
    Hope it works. If above does not answer your problem completely, Pl. do write.
    Best Regards,
    Nirmal Sharma
    India
    Attachments:
    Main_Vi.vi ‏56 KB
    sub_vi.vi ‏25 KB
    global_stop.vi ‏6 KB

  • I get no sound from my guitar when using iRig with my iPod 5th gen (iOS 7)

    I've just bought my iRig and it doesn't work with my iPod 5. I get no sound out of my guitar.
    Headphones are working and when iRig is connected I can hear the samples and every other sound coming out of the iPod, but I get nothing from my guitar.
    I tried shutting the iPod down, turning Mono on/off, but it still doesn't work with any of my apps (Amplitube, Garage Band and AmpKit).
    Then I tried it with my brother's iPod 4 and it worked perfectly, which makes me think that there's something wrong with my iPod settings (I got the iOS 7)....
    Does anyone know something I could try?
    Thanks!

    iOS: Troubleshooting applications purchased from the App Store
    Contact the developer/go to their support site . Maybe it is not compatible with the 5G iPod. Also, it may not be compatible with iOS 7. Did it work on the 5G before iOS 7?
    Restore from backup. See:
    iOS: How to back up              
    Restore to factory settings/new iPod

  • How to program a midi foot controller on Mainstage? Does anyone knows how to program the foot controller with exclusive solo channel in order not to dance "tip tap" while from clean guitar I go to crunch or solo? How to do this programming on Mainstage?

    How to program a midi foot controller on Mainstage? Does anyone knows how to program the foot controller with exclusive solo channel in order not to dance "tip tap" while from clean guitar I go to crunch or solo? How to do this programming on Mainstage?
    I basically managed to learn how to invert parameters which allows me to be as default in the clean guitar channel and if I switch the first button on the midi foot controller I switch to crunch, but at this point I tryied so hard to programm the second and third button to switch, only through a button in one step, to a third channel for distorsion or a 4th channel for solo guitar but I couldn't figured out how this work can be done!
    I would appreciate if anyone could help or share this experience with others who are experiencing the same problem.
    Cheers.
    F.

    I cannot seem to get mainstage to recognize my FCB either. I am using IFCB. Anyone figure this out?
    Thanks,
    Eric

Maybe you are looking for