Always restart after update to 10.5.7

When I set the sleepmodus ore I close my MacBook I always have to restart the PC and it gets very hot. What should I do?

\shrugs
Probably some subtle power management change or something, e.g. trying to power down a device that is already powered down, then waiting for confirmation that never arrives....
Oh, BTW, has anybody tried waiting five or ten minutes to see if it eventually goes to sleep?
P.S. You should probably mark this as solved/answered/* for the benefit of anybody else who runs into this problem.

Similar Messages

Help Me.. E63 always restart after updated softwar...

Dear member nokia forum...please i need help for my E63...after i upgrade software from 100 into 200 my E63 always restart...and i have tried install current software on NOKIA CARE ,, same problem...my E63 still always restart...what happen with my Phone ?? i think i want to downgrade ?? what happen if i downgrade my phone ??
thanks for help....

Try booting in "safe mode". If that stops the restarts, launch the Console utility and look through the categories in the column on the left for crash reports or kernel panic logs.

HT4623 My ipad2 is not restarting after updating to iOS7, I now only get the apple symbol? Please advise what I need to do to get it working again. Thanks.

My ipad2 is not restarting after updating to iOS7, I now only get the apple symbol? Please advise what I need to do to get it working again. Thanks.

Try reset iPad
Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
Note: Data will not be affected.

Mac won't restart after updating to OS X Mountain Lion

Mac won't restart after updating to OS X Mountain Lion. Please help?

Like what happens? Is it just spinning?
If you've waited sufficiently long (say 10 minutes) you could just hit the power button which will do the trick. A little more gentle would be to open a terminal window (if you can) and type 'sudo reboot' (without the quotes) and enter your password when it asks. That will do it too.

HT204347 My MacBook Pro won't restart after update to lion

My Mac book pro won't restart after updating to lion ! Said problem a cured at startup press any key ! No Goodrich

Press and hold power button for up to 30 seconds. Remove battery and reinsert then repeat.

HT2827 i just updated my software for the apple tv and the light is flashing and it wont restart after update thoughts?

i tried to update my software for apple tv and it will not restart after update. flashing lights

Welcome to the Apple Community.
If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
Connect the micro USB cable to the Apple TV and to your computer.
Reconnect the power cable (only for Apple TV 3)
Open iTunes.
Select your Apple TV in the Devices list, and then click Restore.
(You may already have a micro USB cable if you have a camera or other digital device)

I use 1 Icloud account with 2 devise but the other devise arrest out mine, than my devise was not able to connect to itune anymore. My devise still can swich on but it always restart after afew seconds. So can it fix ?

I use 1 Icloud account with 2 devise but the other devise arrest out my devise throue find my iphone, than my devise was not able to connect to itune anymore. My devise still can swich on but it always restart after afew seconds. So can it fix ?

Looking at the error message "The Network Adapter could not establish the connection" , It appears hostname and port may be incorrect. Review the targets.xml under E:\oracle\product\10.2.0\db_1\SAP_solman_SDB\emd and
emoms.properties under E:\oracle\product\10.2.0\db_1\SAP_solman_SDB\config folder to make sure host ( sap_solman) and port (1527) are correct.
As far as setting the environment variables goes, you can go to control panel -> system -> advanced -> environment variables and set the ORACLE_HOME and ORACLE_SID
-Ramesh

Installed latest iOS on my iPad mini, it got stuck while restarting after update. It is still in that stage even after 7 hours.

installed latest iOS on my iPad mini, it got stuck while restarting after update. It is still in that stage even after 7 hours.

Placing your device into recovery (DFU-Device Firmware Upgrade) mode:
Follow these steps to place your iOS device into recovery mode. If your iOS device is already in recovery mode, you can proceed immediately to step 6.
   1. Disconnect the USB cable from the iPhone, iPad, or iPod touch, but leave the
       other end of the cable connected to your computer's USB port.
   2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds
       until the red slider appears, then slide the slider. Wait for the device to turn off.
              * If you cannot turn off the device using the slider, press and hold the
                Sleep/Wake and Home buttons at the same time. When the device turns off,
                release the Sleep/Wake and Home buttons.
3. While pressing and holding the Home button, reconnect the USB cable to the
       device. The device should turn on. Note: If you see the battery charge warning,
       let the device charge for at least ten minutes to ensure that the battery has some
       charge, and then start with step 2 again.
4. Continue holding the Home button until you see the "Connect to iTunes" screen.
       When this screen appears you can release the Home button:
5. If necessary, open iTunes. You should see the following "recovery mode" alert:
6. Use iTunes to restore the device.
If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
Note: When using recovery mode, you can only restore the device. All user content on the device will be erased, but if you had previously synced with iTunes on this computer, you can restore from a previous backup. See this article for more information.

Stop requiring system restart after update

I turn on my machine. Acrobat says there's an update available. I let it update. Then I get a dialog saying:
"You must restart the system before using Acrobat. Click Restart Now to restart automatically".
Come on! It's 2010... Requiring system restart after update is sooo 1990's...
Or put another way, I cannot remember when another app required system restart after updating. Only Acrobat does this nowadays. Please, stop this madness!

While Adobe doesn't deliberately try to annoy users,
it does not deliberately try to remove documented annoyances either.
There are still bugs in Acrobat 9 which have been documented for years, and no one seems interested to fix them.
Serious flaws ... like crashes and corruption of PDF files so they cannot be saved. Hours of work lost.
Every 3rd time I select the Crop icon, I can expect Acrobat 9.4.5 to crash.
There is no excuse for an app to require full reboot on update. C'mon, spend some time at
Microsoft Tech Support and figure it out. Acrobat is also the last application I can remember
requiring reboot.
I turn off Auto Update on both Acrobat and Windows.

My MacBook Pro won't restart after updating iTunes, and so the update doesn't work. I have just purchased an iPad mini and can't sync it - can anyone help?

My MacBook Pro won't restart after updating iTunes, and so the update doesn't work. I have just purchased an iPad mini and can't sync it - can anyone help

Press and hold power button for up to 30 seconds. Remove battery and reinsert then repeat.

MBP 17" will not restart after updating Java... why?

MBP 17" will not restart after updating Java...why?
It would actually try to restart for about 10-15 seconds but would quit and then shut down. Tried using P_R_Command_Options but that too failed and again it just shut down. Tried using D at startup which ran a test of the hard drive. No issues there which tells me there's a software problem.
Can any one help?

Disk Utility suggest reformating
Reformatting is not a Recovery Aid. When Disk Utility suggests reformatting, it is because it considers your drive unsalvageable. Yes, you lose all the data on the drive when you reformat.
And yes, Mac OS X Extended, journaled is the method you will need for a Mac OS X Boot drive.
You should also consider buying a replacement drive to have on hand the next time this internal drive gives you the slightest bit of trouble. Possibly an external enclosure to put it in as well. and it would not hurt to go ahead and Install Mac OS X on it and try booting from it, to make sure it is ready.
And make sure your Backups are current, as the next time that internal drive screws up you may get no warning whatsoever.

Wifi connection alway disconnect after update to iOS6

After update to iOS6 for a month, I found the wifi connection alway disconnect and need to reconnect severaly times. Plese help to suggest for setting up.

Hello there cyldevil,
I would recommend using this article if the Wifi is grayed out in settings.
iOS: Wi-Fi settings grayed out or dim
http://support.apple.com/kb/ts1559
Here is also some additional info on troubleshooting wifi in general on your device from iOS: Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/ts1398
Be sure that you are in range of your Wi-Fi router (access point).
Tap Settings > Wi-Fi and turn Wi-Fi off and then on again.If unable to do so, see this article.
Confirm that your Wi-Fi router and Cable or DSL modem are connected to power, turned on, and indicate that they are connected to the Internet.If not, refer to your network administrator or ISP for assistance.
Restart your iOS device.
Tap Settings > Wi-Fi and locate the Wi-Fi network to which you are connected. Then tap > and Forget this Network. Try to connect to your desired Wi-Fi network again.
Note: You will need to enter your Wi-Fi password again if your desired network requires one.
Turn your Wi-Fi router off and then on again2. If your ISP also provides cable or phone service, check with them before attempting this step to avoid interruption of service.
Update your device to the latest version of software.
Update your Wi-Fi router to the latest firmware2.For AirPort Base Stations, see this article for information about firmware updates.
All the best,
Sterling

Help...MacBook Restarts and Restarts After update ...won't stop

Hello, I just ran the Leopard 10.5.1 software update on my MacBook and it restarted and now it just keeps restarting and makes the sound and it won't stop. Does anyone know what's going on?

That just happened to me. Help. I just did a regular software update, which included a combined operating system update, a QuickTime update and a security update. I restarted after the download as instructed, and now the computer keeps restarting. The little dial keeps spinning and the Apple restart bell goes off, but it never finishes. Then after a few minutes, it restarts itself again.
I've got a big college project in that computer and it's due Monday. Please someone help.

Get Windows Temporary Profile on restart after updating Firefox on Windows 7

This happened a month ago when going from 15 to 15.0.1 also. And again now when upgrading to 16.0.1.
I have no idea how it fixed itself last time as I tried everything over the course of multiple days last time (many reboots, restarts, etc.). Ended up creating two additional accounts, just had the one originally, in order to copy all my files and start over last time. Then, seemingly at random, the original profile worked in which I noticed two instances of FF, 15 and 15.0.1, in the control panel so tried re-installing FF 15.0.1, even though the manifest listed it as successful, which fixed it.
Now the exact thing is happening again after upgrading to 16.0.1. It was a successful install, verified before rebooting via update history and closing FF and opening a couple of times, and it then only listing 16.0.1 in the control panel. But, on the first restart, Windows 7 goes into temporary profile mode again. I tried creating a second account again in hopes the first would magically work again, as I have no idea how I got back into the original profile the last time it happened, to no avail.
Can anyone help? I hate to give up on FF as I've been using it exclusively for years but I don't want to go through this a third time.
Also, what can I do to get back into my original profile so that I don't have to start from scratch yet again copying my files and recreating all my settings?

Update.
After many logoffs, restarts and switching user from the temporary profile and the second user account, it randomly let me back in to my original profile again.
I literally did nothing to allow me access to it other than many of those attempts.
As soon as I was in my original account again, I immediately went to the control panel -> uninstall a program and verified, same as last time, that it listed two instances of FF (recall that it did NOT after I upgraded before the first restart and getting the temp profile). I opened up FF, 16.0.1, and downloaded it again from http://www.mozilla.org/products/download.html?product=firefox-16.0.1&os=win&lang=en-US
Installed that, even though it was already successfully installed according to FF. And just like last time, that removed the earlier instance of FF, 15.0.1, and all is back to normal. Verified by restarting multiple times and no longer getting a temp profile (exactly like last time which lasted for about three weeks until the 16.0.1 upgrade).
This never happened until 15.0.1 and now 2 for 2 with 16.0.1. What is going on that would yield a successful upgrade yet on Windows 7 first restart after is causing it to kick to a temporary profile (yet also fixed, if one gets lucky enough to get back their profile, re-installing it over fixes it until the next upgrade?)? Some file not being created/deleted on reboot that is confusing Windows when trying to load the user profile?
I'm willing to copy over my W7 user profile to a flash drive and Fedex it to the FF team if one can fix this. It is the most basic software setup that I can't imagine others aren't experiencing the same issues.

Disabling restart after updates on a single pc

Hi
SBS 2008.
How can I disable restart after automatic updates on only one Win 7 64 bit pc?
Thanks
Regards

There are a few ways of disabling the automatic reboot.
Method 1.
Go to Windows updates -> Select Change Settings -> Select Download Updates But Let me Choose.. -> Okay.
Method 2.
Click Start -> Run Enter “gpedit.msc” -> Go to Local Computer Policy -> Computer Configuration -> Administrative Templates -> Windows Components -> Windows Update -> Double-click on “No auto-restart for scheduled Automatic
Update installation” -> Enable it! -> Reboot the computer
For better article regarding your issue. Please see the link below.
http://www.techspot.com/guides/230-prevent-automatic-windows-update-restarts/
Regards,
Patrick

Always restart after update to 10.5.7

Similar Messages

Maybe you are looking for