Amplitude and level
Dear sir
What is the difference between amplitude & level measurement with vibration level measurement? I found both has measurement such as RMS and Peak value, but it gave a quite different value when I try it simultaneously.
Can I used the amplitude & level measurement to measure vibration level?
Product differences:
Amplitude and Levels Step is activated by SignalExpress
Vibration Level Step is activated by Sound and Vibration
Functional differences:
Amplitude and Levels Step gives a new result for every block (Step will hold peaks if you check that option)
Amplitude and Levels Step supports measurement of DC
Vibration Level Step always returns the result from the last reset
Vibration Level Step does not measure nor remove DC component; instead this step assumes vibration around equilibrium and/or that the data was acquired with AC coupling
Vibration Level Step supports time-domain integration (to convert acceleration --> velocity --> displacement) prior to the level computation.
Vibration Level Step supports industry-standard (fast, slow, impulse) and custom time constants for exponential level measurements.
What types of vibration are you trying to measure?
Vibration during shock event --> Amplitude and Levels
RMS level of an arbitrary signal --> Amplitude and Levels
Machine or structural vibration --> Vibration Level
In many cases, both steps can be used simultaneously Amplitude and Levels Step outputs can be used for trigger conditions. Vibration Level output (such as Exponential Level and Max-Min) can be used for logging and tracking of industry-standard levels.
Doug
NI Sound and Vibration
Similar Messages
-
Amplitude and level measurements for stereo signal
Hi,
If I input my attached stereo file into Express Amplitude and level measurement (blue icon) it does not give me output value as an array. I want to measure peak to peak value for both left and right channels. I get only left channel value. (No array)
But if I use amplitude and levels.vi I get array as an output for both channels. So i have what I need but I thought I would just post here anyways.
I have attached my audio file.
Sheetal
Thanks.
CVI 2010
LabVIEW 2011 SP1
Vision Builder AI 2011 SP1
Attachments:
AUX_HP1_RSA_OFF.zip 13 KBSheetal,
The output of that express vis is of dynamic data type. You need to convert it to a waveform (use the "from ddt.vi") which will then give you the waveform data type. You can then use the "Get Waveform components" to access the "Y" array data.
Post to let us know if this helped out.
Chris C
Chris Cilino
National Instruments
LabVIEW Product Marketing Manager
Certified LabVIEW Architect -
Error 20312 with Amplitude and Levels vi
Hello,
I have been having a frequent error with a VI in a program I am using. The specific error is:
Error-20312 occurred at "ma_ptmFetch.vi" when called from "Amplitude and Levels N chan.vi"(waveform index 0 of 4)
Possible reasons: The input waveform is zero.
I am using the amplitude and Levels vi to measure the amplitude of 4 current waveforms that are being read into the DAQ card. The error message occurs usually right when the program begins to run, but does not always occur. The DAQ card that is being used for this measurement is a PCI-6071E, and it initially measures many curents and voltages, and then splits them up before sending them to the amplitude and levels vi. When the error does not come up the vi works properly and measures the correct current, so I am not sure what the problem is. If anyone could give me any insight as to what may be the cause of this error, or how to troubleshoot it it would be greatly appreciated.
Thanks,
SteveHello Mike,
I believe you are right, and that this error occurs because the vi is receiving an empty set. When using the generate signal vi, I receive no errors at all, its only when trying to take input from the DAQmx read. I am reading continuous samples from multiple channels in a waveform, and then splitting it up into different sets. I made a small program to bar out any other factors from the large program it is in, and the problem still persists. Also, I tried changing to read only 1 channel. The problem still occurs at this setting, but less frequently than when using multiple channels.
I believe I have found a workaround for this problem, but I'm not sure if there is a better way to go about doing this. I made a sequence with the Start Task vi in the first frame, and the while loop and clear task in the 2nd frame. The while loop contains the DAQmx read vi and the amplitude and levels vi. If I place a Wait vi in the first frame for a short amount of time, say 50ms, the problem disappears. Is it possible the Amplitude and Levels vi is trying to read values before the DAQ is finished starting the task and reading?
I can attach a copy of the small test program I made if you want to see for yourself as well.
Thanks,
Steve -
Amplitude and level measurement two signals
Hello,
I am delveloping a data aquisition VI, I am using the DAQmx and it works fine. I am using the amplitude and measurement express vi to obtain data such as peak to peak etc... I can aquire up to eight channels using the DAQmx, just by selecting the physical channels, but the amplitude and level measurement vi only seems to give me the value of one of the signals (the first one aquired), even though two are being displayed on the graph or even three. How can I display all the peak to peak values for all waveform simultaneously. I am aware that the measurement express is a dynamic data type and conversting the output into an array would work, but I keep on getting errors. Any advice. Attached is the VI and a snapshot of the VI. I also tried splitting the signal with no luck.
Thank you
Attachments:
run.JPG 152 KB
Cont-Acq-and-Graph-Voltage-Int-Clk6.vi 144 KBHI Tareq,
Well I think I tired what you said but it is still not working, here is a snapshot of my VI and the VI itself. I still get the same output
Thank you for your help
Alloush
Attachments:
Cont-Acq-and-Graph-Voltage-Int-Clk7mod.vi 145 KB
run.JPG 160 KB -
How should I set the parameters of PID Autotuning such as relay amplitude and PV noise level?
I want to control the temperature of a room by changing the hot water flow of a radiator with a control valve. The desirable control accuracy is +/- 0.5 degree of centigrade.
What number should I set for relay amplitude? And what number should I set for PV noise level?Hello loghmani,
If your output is saturating try to reduce your relay amplitude and/or reduce the gain Kc of the PID controller before starting the autotuning procedure. You can find more information about each of the parameters that you've inquired about at this KnowledgeBase article.
I would recommend taking a look at the General Auto PID Simulator.vi example. You can find this example by doing a search in the example finder or by clicking linked example at the bottom of the detailed help page of the Autotuning PID.vi.
If you haven't looked at the PID user manual that also contains useful information on setting up PID algorithims and Autotuning.
David A
National Instruments
FlexRIO Product Support Engineer -
What are the "Profile" and "Level" Settings in AME?
One thing I never understood is the option for the Profile and Level when I'm exporting a clip in AME. Not sure if those are options for most codecs but it is for the MainConcept H.264 Video Codec. For Profile, there is an option of "Baseline", "Main", and "High". For Level, starting from 3.1 and up, it's 3.1, 3.2, 4.0, 4.1, 4.2, 5.0, 5.1. I don't know what these are and therefore don't know which to choose. I know that the level has something to do with resolution so if I'm exporting in 720p, which level should I choose?
**While on the video encoding topic, in terms of quality, best to worst, what would the order be for the types of bitrates? Is it VBR 2-pass, CBR, then VBR 1-Pass?
-Sorry if this is a bit off-topic for Premiere CS4. There just wasn't any specific location for AME or Video-encoding..Profiles outline/suggest certain encoding/decoding capabilities of a given video compression standard, like H.264. For example, the High profile enables B-frames and CABAC encoding. Levels are a means of ensuring that a hardware decoder can properly decode a stream. For example, an iPod can play back Baseline profile, Level 3.0 encoded video, but nothing higher. Higher profiles and levels enable other hardware, like Blu-Ray players. For the most part, you can ignore levels when encoding for computer playback, and only concern yourself with profile. I pretty much stick with [email protected]
The link Eddie posted has a ton of information, but here's a good article from Jan Ozer that puts it in more accessible terms. -
Default Pay scale group and Level in infotype-0008
Hi,
While hiring should display the default Pay scale group and Level in infotype-0008 or the pay scale group and level can default from the Job or position. Itu2019s possible? Thanks in advance.
RegardsNo there is no standard Feature to default PSG and PSL. TARIFF is for PSA and PST.
Wait for some body may have some information.
Afrasyab -
Defaulting PayScale Group and Level in IT0008.
The System is configured as that the Payscale Group and Level will get defaulted in IT0008 from the Planned Compensation maintained for the Job.
This is working fine for all personnel areas except one.
Can anyone pls explain what all tables/SPRO nodes I have to check for the same?Hi,
Check the Indirect valuation A, B, C & D config in the Reiumbursement Allownace & Perqusities( RAP's )config for the combination of PSArea, PSType, PSGroup, PSlevel
Regards,
Hemant V. Mahale -
Hello!!!how can I control an omron plc (sysmac cqm1)with an OPC server?I want to adquire a signal controlling its amplitude and frecuency.How can it be done with OPC server?I already have the NI CD of OPC drivers.Thank you
Hola Jose David, que OPC estas utilizando?, Si tienes comunicación entre tu computadora y PLC pero falla la comunicación entre el OPC y el PLC? La configuración y direcciones entre los dos es correcta? La comunicación es por cable serial?
Espero tus respuestas
Saludos
Benjamin C
Senior Systems Engineer // CLA // CLED // CTD -
Rman backup full then level 0 and level 1 Weekly
Please share your thoughts of backups.
Friday -> Take a full rman backup
Saturday -> Take a level 0 rman backup -> If recovery needed restore full and apply level 0 ?
Sunday -> Take a level 1 rman backup -> If recovery needed restore full and apply incremental 1 ?
Monday -> Take a level 2 rman backup -> If recover needed restore full and apply incremental 1 ?
Tuesday -> Take a level 1 rman backup -> If recover needed restore full and apply incremental 2 ?
Wednesday -> Take a level 2 rman backup -> If recovery needed restore full and apply incremental 1 ?
Thursday -> Take a level 1 rman backup -> If recovery need restore full and apply incremental 2 ?
ThanksPlease note that Full and level 0 backs are same...
Sunday -> Take a level 0 rman backup
Monday -> Take a level 1 rman backup
Tuesday -> Take a level 1 rman backup
Wednesday -> Take a level 2 rman backup
Thursday -> Take a level 1 rman backup
Friday-> Take a level 1 rman backup
Saturday -> Take a level 1 rman backup
Taking level 2 in the middle of the week, so that in case of any recovery you need ao apply changes since the last level 0, 1 or 2 -
Hi Everybody
I have to schedule my rman backup in the following manner.
1. Weekly once level 0 backup has to run
2. Rest of the other days level 1 backup has to run to disk
3. In between the week if we moved all backup to some other destination, the backup schedule has to run the level 0 instead of incremental backup automatically.
Then level 1 backup follows the level 0 backup.
Can anyone help me out how to schedule this task that satisfies the above three condition.Thanks Aman
My manager he needs like windows backup that level 0 run at once in a week and level 1 follows till end of the week if we remove the backup or moved within the week then backup folder will be empty that time level 0 has to run instead of next incremental backup.
For example: I am schedule the rman by following manner by windows schedule task with script.
1. Level 0 is scheduled at saturday only
2. level 1 is scheduled from sunday to thursday.
My manager he don't want like this. level 0 should not run by day like saturday. he wants script will check the disk if level 0 is existing or not
if existing it will replace the level 0 with new one.
if not existing it will create the new one.
Is there possible to run level 0 and level 1 in the same script. -
Defaulting Pay Scale Group and Level
Dear All,
Is there any way of defaulting Pay Scale Group and Level as they are fixed for Employee Sub-Groups?
Regards,
Ahsan ZaidiTARIF: Default Pay Scale Type and Area in the Basic Pay
Object
Feature
Task
With this feature you control whether the default value is determined
from the T001P from the personnel area and personnel subarea, or whether
the default value is determined direct from the feature.
The return value must have the form xx/yy, when xx is the pay scale
type, and yy the pay scale area.
If the feature returns SPACE as a value, then the value pay scale type
or pay scale area is determined by table T001P. If the value does not
equal SPACE, then this value will be taken as the pay scale type or pay
scale area.
You can either enter return both values or only one of the two values.
The missing value is determined from table T001P. -
CAT2 - Payscale group and level
Does anyone know how to get project systems / finance to read the payscale group and levels from HR (instead of reading the rate from Project Systems - CP26).
Thanks.
(we have too many rates to store in Project systems and would prefer to store them in HR, any ideas?)Hi Dianna,
Do you want to get payscale groups and level on CAT2 screen(time entry screen).
If thats your question,yes you can get that.For that you have change the settings of the CATS profile you are using.
The Display IMG path is
Cross-Application Components->Time Sheet->Time Recording--->Choose Fields
And in that click on DataEntry selection and uncheck the hide radio button for the Payscale area and group.
Hope this helps
Pl let me know if you have any questions -
Default Payscale group and level
Hi Experts,
Is there any way by which i can default the Payscale Group and Payscale Level? My payscale group is same as Employee Group and level is same as Employee Sub-group.
Plz advice.
regards
TSHi
You ca use tariff to default the payscale group and level for particular payroll area
you can maintain a parameter transaction for PC00_M10_CALC_SIMU inn SE93.to maintain payroll schema and payroll area as default
Reward Points -
In adobe premiere cc 2014 , in the version for Apple , there is the " dynamics" in the audiometer / amplitude and compression/dynamics. In the same version for PC , there is no option. Somebody is also having this problem ? tks
are you referring to the audio meters panel? im on windows, and i can right click the meters panel and get options for "dynamic peaks". there are audio effects, from the effects panel if thats what you are looking for? i have one named "Dynamics" as well as several compressors.
Maybe you are looking for
-
How do i stop notifications from ringing while im on a phone call on the iphone 4s
how do i stop notifications from ringing while im on a phone call on the iphone 4s?
-
Creation of Tree View in CRM web ui
Hi All, How to create a Tree View in CRM web ui.Please let me know the step by step procedure. Thanks, Santhosh.
-
Hi All, Can anyone help me on this errro in CAF GP Design Time When I am trying to clickon CAF GP->administration->Email Template I am getting the following error: "The following error occured while populating the list: The language dependent mim
-
Hello I am trying to use the external Bank reconciliation in SAP Business One 2007. I want to import the bank statement from my bank to the: Process External Bank Statement window. I will develop a special add-on. But the question is, i have around 1
-
Transactional replication update causing deadlock
Hello, I am using sql server 2012 SE. I am using Transactional replication and noticed that we have been receiving deadlocks lately. The select statement that is inserting data into a temptable is getting deadlocked by the transactionalreplication up