An error occurred while verifying disc.

Hi, whenever I try to burn a CD (any brand) the burn goes through ok and when it gets to verify (any cd burning software) it says "This disc may not work. An error occurred while verifying disc."
I have reinstalled, clean installed, done everything even tried a NEW cd drive and got the same issue. So, I am sure it's a software problem.
When I do run a burn, this is what I get:
IWhat I have been doing is running the "Console" application from the Utilies folder to see what is going on.
This is the message I get:
Finder: Burn underrun protection is supported, and enabled.
Finder: Burn finished, Sun Feb 5 19:04:56 2006
Finder: Verify started, Sun Feb 5 19:04:56 2006
Finder: Discrepancy in block 68 at byte 42.
Finder: Source data: 31D5 2B31 E3B3 3B3B 1FD1 D2C8 52ED 1D51
Finder: Burned data: 31D5 2B31 E3B3 3B3B 1FD1 52C8 52ED 1D51
Finder: Verify failed, Sun Feb 5 19:04:58 2006
There is always a problem with byte 42 and the SOURCE DATA is always different from the BURNED DATA by one element.
Always in exactly the same sector of numbers digits. As you can see in the source data it reads "D2C8" and in burned data it reads "52C8"
Here is a message from a different burn attempt:
Finder: Burn underrun protection is supported, and enabled.
Finder: Burn finished, Sun Feb 5 18:39:42 2006
Finder: Verify started, Sun Feb 5 18:39:42 2006
Finder: Discrepancy in block 220 at byte 42.
Finder: Source data: 9F2F 059B 208F 5CD7 A197 EBB2 B35D BF53
Finder: Burned data: 9F2F 059B 208F 5CD7 A197 6BB2 B35D BF53
Finder: Verify failed, Sun Feb 5 18:39:44 2006
As you can see its the same byte problem and same problem with burned/source data.
I have no clue what to do - any advice would be great.
I have reinstalled a million times, clean install, everything.
Is it a byte problem? kernel problem? It's worked once or twice after a clean install but never again. It's been this way from the box and Apple refused to fix it. So now I am stuck hoping for some advice.
Thanks

The fact that it worked once or twice after a clean install suggests that you may want to defrag your HDD; esp. if you have only one and the OS is on the same partition as your data.
You will need TTP4 or Disc Warrior, etc., to accomplish this. Disc Utility cannot do it.
Personally, I never bother with verification. Unless the data is extremely sensitive, there's no real point. If the disc loads OK, and you can read/copy the data back to your HDD, that's what counts.

Similar Messages

TS3510 MSG is An error occurred while verifying your email

Trying to FaceTime but getting message that FaceTime Activation: an error occurred while verifying your email

ever figure this out? having a similar issue with a mac.com address...
we have a central mac.com email address with several aliases attached to it...all but 1 of those aliases have been successfully setup on separate ipods or iphones except for my wife's.
under "Messages," my wife has the central mac.com address and her phone number as eligible contacts. when i try to add her mac.com alias it bugs out and gives me the "verifying your email" error...also immediate...no chance it's really pinged anything in the time it took to display the error.

"An error occurred while verifying your email"

This actually applies as much to iMessage on iOS as to FaceTime (on both Mac and iOS). I have both services set up and functioning, using my Apple ID as my email address, on my Mac, iPad 2, and iPhone 4.
What I’d like to do is use a custom email address that I can give out to people without clogging my real email with spam. So I went into cpanel at my webhost and created a custom address each for iMessage and Facetime. I’ve tested them and they can send & receive email.
But when I try to add these addresses to either app, on Mac (FaceTime) or iOS (both), I invariably get the “An error occurred while verifying your email" alert. And this is immediate, like it barely had time to ping the web before giving up.
I've tried resetting my network settings on the iPad but it made no difference. I also tried making yet another new email address and it was the same. I also tried making addresses with .com and .jp with no change.
What might be wrong?

ever figure this out? having a similar issue with a mac.com address...
we have a central mac.com email address with several aliases attached to it...all but 1 of those aliases have been successfully setup on separate ipods or iphones except for my wife's.
under "Messages," my wife has the central mac.com address and her phone number as eligible contacts. when i try to add her mac.com alias it bugs out and gives me the "verifying your email" error...also immediate...no chance it's really pinged anything in the time it took to display the error.

Face time activation - an error occurred while verifying your email

i can't get facetime to work on my iPad - i go to settings add my account details and password (i know they are correct as i just logged onto my apple account and they worked fine) - and when i click on "next" the message that comes up is "an eror occurred while verifying your email" - i've rebooted etc but i can't get it to work - on ios5 it was no problem..help!

ever figure this out? having a similar issue with a mac.com address...
we have a central mac.com email address with several aliases attached to it...all but 1 of those aliases have been successfully setup on separate ipods or iphones except for my wife's.
under "Messages," my wife has the central mac.com address and her phone number as eligible contacts. when i try to add her mac.com alias it bugs out and gives me the "verifying your email" error...also immediate...no chance it's really pinged anything in the time it took to display the error.

TS4185 'an error occurred' while verifying comes up when I try to activate, what can i do?

Can someone help me with this, I can't seem to sign on and get started on my new macbook pro. Also, I am calling (facetiming) from my ipad to my phone and it rings on the ipad end but not the iphone end, but then shows up as a missed call on the iphone end. How does this work????

Does it help if you either disable SSL3 or disable TLS as a test?
security.tls.version.min = 1 and security.tls.version.max = 1 disables SSL3 and enables TLS 1.0
security.tls.version.max = 0 and security.tls.version.max = 0 enables SSL3 and disables TLS 1.0
Type about:config in the location (address) bar and press the Enter key to open the about:config page like you open a website by typing the URL in the location bar.
*If you see a warning message then you can confirm that you want to access the about:config page.
*http://kb.mozillazine.org/about:config
See:
*http://kb.mozillazine.org/security.tls.version.*
0 means SSL 3.0, 1 means TLS 1.0, 2 means TLS 1.1, etc.
You can try to rename the cert8.db file in the Firefox profile folder to cert8.db.old or delete the cert8.db file to remove intermediate certificates that Firefox has stored.
If that helped to solve the problem then you can remove the renamed cert8.db.old file.
Otherwise you can rename (or copy) the cert8.db.old file to cert8.db to restore the previous intermediate certificates.
Firefox will automatically store intermediate certificates when you visit websites that send such a certificate.
If that didn't help then remove or rename secmod.db (secmod.db.old) as well.

A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (p

A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that
the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server)(Microsoft SQL Server, Error: 2)
The system cannot find the file specified
Cannot connect to COWBOYS.
Here are the technical details===================================
A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider:
Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (.Net SqlClient Data Provider)
For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft%20SQL%20Server&EvtSrc=MSSQLServer&EvtID=2&LinkId=20476
Error Number: 2
Severity: 20
State: 0
Program Location:
at System.Data.SqlClient.SqlInternalConnection.OnError(SqlException exception, Boolean breakConnection, Action`1 wrapCloseInAction)
at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning(TdsParserStateObject stateObj, Boolean callerHasConnectionLock, Boolean asyncClose)
at System.Data.SqlClient.TdsParser.Connect(ServerInfo serverInfo, SqlInternalConnectionTds connHandler, Boolean ignoreSniOpenTimeout, Int64 timerExpire, Boolean encrypt, Boolean trustServerCert, Boolean integratedSecurity, Boolean withFailover)
at System.Data.SqlClient.SqlInternalConnectionTds.AttemptOneLogin(ServerInfo serverInfo, String newPassword, SecureString newSecurePassword, Boolean ignoreSniOpenTimeout, TimeoutTimer timeout, Boolean withFailover)
at System.Data.SqlClient.SqlInternalConnectionTds.LoginNoFailover(ServerInfo serverInfo, String newPassword, SecureString newSecurePassword, Boolean redirectedUserInstance, SqlConnectionString connectionOptions, SqlCredential credential, TimeoutTimer
timeout)
at System.Data.SqlClient.SqlInternalConnectionTds.OpenLoginEnlist(TimeoutTimer timeout, SqlConnectionString connectionOptions, SqlCredential credential, String newPassword, SecureString newSecurePassword, Boolean redirectedUserInstance)
at System.Data.SqlClient.SqlInternalConnectionTds..ctor(DbConnectionPoolIdentity identity, SqlConnectionString connectionOptions, SqlCredential credential, Object providerInfo, String newPassword, SecureString newSecurePassword, Boolean redirectedUserInstance,
SqlConnectionString userConnectionOptions, SessionData reconnectSessionData)
at System.Data.SqlClient.SqlConnectionFactory.CreateConnection(DbConnectionOptions options, DbConnectionPoolKey poolKey, Object poolGroupProviderInfo, DbConnectionPool pool, DbConnection owningConnection, DbConnectionOptions userOptions)
at System.Data.ProviderBase.DbConnectionFactory.CreateNonPooledConnection(DbConnection owningConnection, DbConnectionPoolGroup poolGroup, DbConnectionOptions userOptions)
at System.Data.ProviderBase.DbConnectionFactory.TryGetConnection(DbConnection owningConnection, TaskCompletionSource`1 retry, DbConnectionOptions userOptions, DbConnectionInternal oldConnection, DbConnectionInternal& connection)
at System.Data.ProviderBase.DbConnectionInternal.TryOpenConnectionInternal(DbConnection outerConnection, DbConnectionFactory connectionFactory, TaskCompletionSource`1 retry, DbConnectionOptions userOptions)
at System.Data.ProviderBase.DbConnectionClosed.TryOpenConnection(DbConnection outerConnection, DbConnectionFactory connectionFactory, TaskCompletionSource`1 retry, DbConnectionOptions userOptions)
at System.Data.SqlClient.SqlConnection.TryOpenInner(TaskCompletionSource`1 retry)
at System.Data.SqlClient.SqlConnection.TryOpen(TaskCompletionSource`1 retry)
at System.Data.SqlClient.SqlConnection.Open()
at Microsoft.SqlServer.Management.SqlStudio.Explorer.ObjectExplorerService.ValidateConnection(UIConnectionInfo ci, IServerType server)
at Microsoft.SqlServer.Management.UI.ConnectionDlg.Connector.ConnectionThreadUser()
===================================
The system cannot find the file specified
I have tried from so many forms. This is so frustrating. Thank for everyone/anyone who wants to help. So this is what happened: I had to uninstall my previous sqlserver 2012(which worked great) for some reason, and I uninstalled everything from that download.
Then I installed the trial edition of sql server 2012 (64 Bit) and It wouldn't connect to the database. (Error mentioned above.) My local DB is COWBOYS. (COWBOYS is also my computer name.) After this, I have tried downloading sqlexpress and sqlserver 64bit
many times and cannot connect to my local DB.
How do I connect to my Local DB?
Also, I think this might help: (When I run sqlserve.exe, which I was able to find in C:\Program Files\Microsoft SQL Server\110\LocalDB\Binn, I get an error: Your SQL server installation is either corrupt or has been tampered with(Error getting
instance ID from name). Please uninstall then re-run setup to correct this problem.
I would happily re install it, if it wasn't my 20th time.
I don't have any remote connections, I don't use username/password, only window authentication. I work mostly on visual studio, but without able to store /retrieve data, I don't know how to survive.
May be the solution is very simple, but I am too frustrated.
Some of the things I have tried:
From a command prompt, enter one of the following commands:
net start "SQL Server Agent (MSSQLSERVER)" OR
net start "SQL Server Agent(instancename)"(for instance)
on my sql configuration, I cannot start anything because there is nothing there to start. I can post more details, if that would help. Also, some more details about the error:
Details
Product:
SQL Server
ID:
2
Source:
MSSQLServer
Version:
10.0
Component:
SQLEngine
Message:
An error has occurred while establishing a connection to the server. When connecting to SQL Server, this failure may be caused by the fact that under the default settings SQL Server does not allow remote connections. (provider: Named Pipes Provider, error:
40 - Could not open a connection to SQL Server) (.Net SqlClient Data Provider)
Explanation
SQL Server did not respond to the client request because the server is probably not started.
User Action
Make sure that the server is started.
Version:
9.0
Component:
SQLEngine
Message:
An error has occurred while establishing a connection to the server. When connecting to SQL Server 2005, this failure may be caused by the fact that under the default settings SQL Server does not allow remote connections. (provider: Named Pipes Provider, error:
40 - Could not open a connection to SQL Server) (.Net SqlClient Data Provider)
Explanation
SQL Server did not respond to the client request because the server is probably not started.
User Action
Make sure that the server is started.
Any one that can help me, I will be greatful. Thank you so much. p.s. please ask me anything if you have any questions.

It sounds like there are a couple things going on here. First check if you have a successful install of SQL Server, then we'll figure out the connection issues.
Can you launch SQL Server Configuration Manager and check for SQL Server (MSSQLSERVER) if default instance or SQL Server (other name) if you've configured your instance as a named instance. Once you find this, make sure the service is started.
If not started, try to start it and see if it throws an error. If you get an error, post the error message your hitting. If the service starts, you can then launch SSMS and try to connect. If you have a default instance, you can use the machine
name in the connection dialog. Ex: "COWBOYS" where Cowboys is the machine name. However, if you named the SQL Server instance during install, you'll need to connect using the machine\instance format. Ex: COWBOYS\Romo (where Romo
is the instance name you set during install).
You can also look at the summary.txt file in the SQL Server setup error logs to see what happened on the most recent install. Past install history is archived in the log folder if you need to dig those up to help troubleshoot, but the most
recent one may help get to the bottom of it if there is an issue with setup detecting a prior instance that needs to be repaired.
Thanks,
Sam Lester (MSFT)
http://blogs.msdn.com/b/samlester
This posting is provided "AS IS" with no warranties, and confers no rights. Please remember to click
"Mark as Answer" and
"Vote as Helpful" on posts that help you. This can be beneficial to other community members reading the thread.

Excel, PowerView error in SharePoint 2013: "An error occurred while loading the model for the item or data source 'EntityDataSource'. Verify that the connection information is correct and that you have permissions to access the data source."

I've installed SQL Server 2012 SP1 + SP server 2012 + SSRS and PowerPivot add-in.
I also configured excel services correctly. Everything works fine but the powerview doesn't work!
While I open an excel workbook consist of a PowerView report an error occurs: "An error occurred while loading the model for the item or data source 'EntityDataSource'. Verify that the connection information is correct and that you have permissions
to access the data source."
error detail:
<detail><ErrorCode xmlns="http://www.microsoft.com/sql/reportingservices">rsCannotRetrieveModel</ErrorCode><HttpStatus xmlns="http://www.microsoft.com/sql/reportingservices">400</HttpStatus><Message xmlns="http://www.microsoft.com/sql/reportingservices">An
error occurred while loading the model for the item or data source 'EntityDataSource'. Verify that the connection information is correct and that you have permissions to access the data source.</Message><HelpLink xmlns="http://www.microsoft.com/sql/reportingservices">http://go.microsoft.com/fwlink/?LinkId=20476&EvtSrc=Microsoft.ReportingServices.Diagnostics.Utilities.ErrorStrings&EvtID=rsCannotRetrieveModel&ProdName=Microsoft%20SQL%20Server%20Reporting%20Services&ProdVer=11.0.3128.0</HelpLink><ProductName
xmlns="http://www.microsoft.com/sql/reportingservices">Microsoft SQL Server Reporting Services</ProductName><ProductVersion xmlns="http://www.microsoft.com/sql/reportingservices">11.0.3128.0</ProductVersion><ProductLocaleId
xmlns="http://www.microsoft.com/sql/reportingservices">127</ProductLocaleId><OperatingSystem xmlns="http://www.microsoft.com/sql/reportingservices">OsIndependent</OperatingSystem><CountryLocaleId xmlns="http://www.microsoft.com/sql/reportingservices">1033</CountryLocaleId><MoreInformation
xmlns="http://www.microsoft.com/sql/reportingservices"><Source>ReportingServicesLibrary</Source><Message msrs:ErrorCode="rsCannotRetrieveModel" msrs:HelpLink="http://go.microsoft.com/fwlink/?LinkId=20476&EvtSrc=Microsoft.ReportingServices.Diagnostics.Utilities.ErrorStrings&EvtID=rsCannotRetrieveModel&ProdName=Microsoft%20SQL%20Server%20Reporting%20Services&ProdVer=11.0.3128.0"
xmlns:msrs="http://www.microsoft.com/sql/reportingservices">An error occurred while loading the model for the item or data source 'EntityDataSource'. Verify that the connection information is correct and that you have permissions to access the
data source.</Message><MoreInformation><Source>Microsoft.ReportingServices.ProcessingCore</Source><Message msrs:ErrorCode="rsErrorOpeningConnection" msrs:HelpLink="http://go.microsoft.com/fwlink/?LinkId=20476&EvtSrc=Microsoft.ReportingServices.Diagnostics.Utilities.ErrorStrings&EvtID=rsErrorOpeningConnection&ProdName=Microsoft%20SQL%20Server%20Reporting%20Services&ProdVer=11.0.3128.0"
xmlns:msrs="http://www.microsoft.com/sql/reportingservices">Cannot create a connection to data source 'EntityDataSource'.</Message><MoreInformation><Source></Source><Message>For more information about this error navigate
to the report server on the local server machine, or enable remote errors</Message></MoreInformation></MoreInformation></MoreInformation><Warnings xmlns="http://www.microsoft.com/sql/reportingservices" /></detail>
Please help me to solve this issue. I don't know if uploading the excel workbook is enough or maybe It needed to connect to another data source.
I Appreciate in advance.

Hi Ali.y,
Based on the current error message, the error can be related to the
Claims to Windows Token Service (C2WTS) and is an expected error under certain conditions. To verify the issue, please check the aspects below:
 1. The C2WTS Windows service and C2WTS SharePoint service are both running.
 2. Check the SQL Server Browser service is running on the machine that has the PowerPivot instance of SSAS.
 3. Check the domain. You're signing into SharePoint with a user account in some domain (call it Domain A). When Domain A is equal to Domain B which SharePoint server itself is located (they're the same domain), or Domain
A trusts Domain B.
In addition, the error may be caused by Kerberos authentication issue due to missing SPN. In order to make the Kerberos authentication work, you need to configure the Analysis Services to run under a domain account, and register the SPNs for the Analysis
Services server.
To create the SPN for the Analysis Services server that is running under a domain account, run the following commands at a command prompt:
• Setspn.exe -S MSOLAPSvc.3/Fully_Qualified_domainName OLAP_Service_Startup_Account
Note: Fully_Qualified_domainName is a placeholder for the FQDN.
• Setspn.exe -S MSOLAPSvc.3/serverHostName OLAP_Service_Startup_Account
For more information, please see:
How to configure SQL Reporting Services 2012 in SharePoint Server 2010 / 2013 for Kerberos authentication
Regards,
Heidi Duan
Heidi Duan
TechNet Community Support

An error occurred while burning the disc.

I tried to burn some stuff onto a DVD today with my PowerBook. Here's the info on the burner:
MATSHITA DVD-R UJ-845E:
Manufacturer: MATSHITA
Model: MATSHITA DVD-R UJ-845E
Revision: DMP2
Serial Number:
Drive Type: CD-RW/DVD-RW
Disc Burning: Apple Supported/Shipped
Removable Media: Yes
Detachable Drive: No
I bought some DVD's on sale at Radio Shack, and when I tried to burn a movie and a few photos onto a disc, the progress bar showed it starting to burn, then it stopped and I got this message:
"An error occurred while burning the disc. This disc cannot be used."
A little research here at the Apple forum brought me to this site:
http://www.digitalfaq.com/media/dvdmedia.htm
And after downloading a little program called DVD Media Inspector, I was able to classify the DVD's I had bought as:
"4TH CLASS MEDIA:
Pathetic garbage media, landfill material, about 0-50% success rate...."
OK, off to Mega Lo Mart, where I bought some nice, expensive Maxell DVD's.
Media Inspector doesn't see my fancy new DVD's. When I try to burn stuff using the Finder, I get the same result as before.
Getting desperate at that point, I located and downloaded updated firmware for my model of Matshita superdrive. I'm not sure what firmware is, and there was a free range one and a standard one, so I went for the standard one. There were dire warnings in the readme file about "flashing" a superdrive being on the same risk level as open heart surgery. I flashed my superdrive. (You can say that here, and it's not dirty.)
I also tried burning using iDVD, and after much preparation, it started to burn, then spit out the DVD. I tried three of the landfill DVD's and two of the Maxell ones. I'm out of things to try. Any ideas?
I have never tried burning DVD's before. Am I doing something wrong?

I tried again using iDVD's One-Step DVD making feature. It will let you make a one step from a movie file, and I had a .dv version of the movie I want to burn.
It encoded video for a while, encoded audio for a little while, then started to burn. The superdrive made some noises, then the DVD was ejected and I got an error message saying:
"Burning Finished
Errors were found during the burning process"
I hit OK (though it really wasn't OK) and got another error message box. This one said:
"Multiplexer error
(some message about multiplexing problem)"
The message didn't make sense to me, and I was unable to remember it. What's a multiplexer? I would have guessed an avid movie-goer, but somehow I think that is not it.

Connecting to the LOB system has failed. A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is

hi ,
when generate the schema , i got the below error, please any one put your inputs:
Connecting to the LOB system has failed. A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server
is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server).

thaks shanky,
but facing another , after generate schema from WCF_SQL, im unable get elements in my schema.
this is schema generate from storeprocduer , but thru WCF-sql im unable get the elements like
id, name
<xsd:schema targetNamespace="urn:schemas-microsoft-com:sql:SqlRowSet2" xmlns:schema="urn:schemas-microsoft-com:sql:SqlRowSet2" xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns:sqltypes="http://schemas.microsoft.com/sqlserver/2004/sqltypes" elementFormDefault="qualified">
<xsd:import namespace="http://schemas.microsoft.com/sqlserver/2004/sqltypes" schemaLocation="http://schemas.microsoft.com/sqlserver/2004/sqltypes/sqltypes.xsd" />
<xsd:element name="Test.dbo.sample">
<xsd:complexType>
<xsd:sequence>
<xsd:element name="id" type="sqltypes:int" minOccurs="0" />
<xsd:element name="name" minOccurs="0">
<xsd:simpleType>
<xsd:restriction base="sqltypes:nvarchar" sqltypes:localeId="1033" sqltypes:sqlCompareOptions="IgnoreCase IgnoreKanaType IgnoreWidth" sqltypes:sqlSortId="52">
<xsd:maxLength value="1000" />
</xsd:restriction>
</xsd:simpleType>
</xsd:element>
</xsd:sequence>
</xsd:complexType>
</xsd:element>
</xsd:schema>
<Test.dbo.sample xmlns="urn:schemas-microsoft-com:sql:SqlRowSet2">
<id>18</id>
<name>BIRADAR</name>
</Test.dbo.sample>
<Test.dbo.sample xmlns="urn:schemas-microsoft-com:sql:SqlRowSet2">
<id>18</id>
<name>BIRADAR</name>
</Test.dbo.sample>
<Test.dbo.sample xmlns="urn:schemas-microsoft-com:sql:SqlRowSet2">
<id>19</id>
<name>sw</name>
</Test.dbo.sample>
<Test.dbo.sample xmlns="urn:schemas-microsoft-com:sql:SqlRowSet2">
<id>18</id>
<name>BIRADAR</name>
</Test.dbo.sample>
<Test.dbo.sample xmlns="urn:schemas-microsoft-com:sql:SqlRowSet2">
<id>14</id>
<name>swe</name>
</Test.dbo.sample>
<Test.dbo.sample xmlns="urn:schemas-microsoft-com:sql:SqlRowSet2">
<id>13</id>
<name>se</name>
</Test.dbo.sample>

A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections.

A network-related or instance-specific error occurred while establishing a connection to SQL Server. The
server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26- Error:Locating Server\instance Specified)
How Can i solve this?

1. Make sure SQL Server Service is running
2. If a named instance, make sure SQL Server browser service is running
3. Make sure SQL Server is configured to allow remote connections
4. Examine the SQL Server error log for messages confirming that SQL is listening on the expected network interfaces and ports
5. Test server connectivity with PING from the client machine
6. Test port connectivity using TELNET or PowerShell to the server and port (from step 4) from the client machine. For example
a. TELNET <server-name> 1433
b. PowerShell: 1433 | % { echo ((new-object Net.Sockets.TcpClient).Connect("YourServerName",$_)) "server listening on TCP port $_" }
7. Check firewall settings if step 5 or 6 connectivity test fails
Best Regards,Uri Dimant SQL Server MVP,
http://sqlblog.com/blogs/uri_dimant/
MS SQL optimization: MS SQL Development and Optimization
MS SQL Consulting:
Large scale of database and data cleansing
Remote DBA Services:
Improves MS SQL Database Performance
SQL Server Integration Services:
Business Intelligence

Move to new computer, get "An error occurred while reading files or writing files to disc. The disc

I tried to move my PE6 install and catalog to a new computer. It was on a Dell Windows XP machine, and I moved it to a Toshiba Windows 7 (64 bit) machine. I have always kept my photo files on an external hard drive. My photo library is 50GB, 10,000 files. Here is what I did.
Copied the original PE6 install file to the Toshiba. Installed but didn’t activate it.
Copied the entire My Catalog folder to the proper Windows 7 location.
Plugged the external drive into the Toshiba. Made sure the same drive letter as before (E).
Fired up PE6 on Toshiba. Looked good in Organizer. Everything seemed to be there, but I didn't try to make changes at that point.
Deactivated PE6 on the Dell. Activated on the Toshiba.
Then I realized that it is not right. I can edit Keywords and Rating stars on the pics, but not dates, captions or notes. I get “An error occurred while reading files or writing files to disc. The disc may be full or there may be problems with the source media.”
Only a fraction of the external drive is in use.
I can access the files on the external drive with another app (Windows Photo Viewer).
I tried Reconnect All Missing Files. Somewhat ambiguously, it says “There are no files to reconnect.”
In the properties in the Organizer for each picture are the proper file names and paths. Folder view works fine in Organizer.
I can put new files in the same external drive directories, import them into PE6, then edit them normally.
What is the easiest way to get Organizer properly connected to my files? I suppose I could reimport all the pics on the new machine, but I assume I'd lose some of my metadata. So that is out of the question.
Thanks,
Bill

Are you sure that file paths are correct? I say this because under XP they would have originally pointed to Documents & Settings/My Pictures whereas on W7 it will be User/Pictures, albeit you are using an external hd.
Take a look at this knowledge base note on the correct procedure for back-up and restore.
I think writing metadata to files for such a large catalog will be a thankless task.
http://helpx.adobe.com/photoshop-elements/kb/backup-restore-move-catalog-photoshop.html

Using Time Machine to back up two systems, OS10.8.3, and OS 10.6.8. Sometimes it backs them up, sometimes I receive this: Backup was not performed because an error occurred while copying files to the backup disc. The problem may be temporary...

Using Time Machine to back up two systems, OS10.8.3, and OS 10.6.8. Sometimes it backs them up, sometimes I receive this: Backup was not performed because an error occurred while copying files to the backup disc. The problem may be temporary...

Hello,
Thanks to the great Pondini...
http://pondini.org/TM/C3.html

How do I fix this error "An error occurred while sending mail. The mail server responded: Authentication is required before sending [R0107005]. Please verify

My previous request had an incorrect email. This error began yesterday and I can't reply or send new emails from my PC, but email is working on my iphone.

I have been doing that. Here is the complete message I get. It was cut off in my initial question. "An error occurred while sending mail. The mail server responded: Authentication is required before sending [R0107005]. Please verify that your email address is correct in your Mail preferences and try again."

Error Message: An error occurred while reading files or writing files to disc...

Why am I getting the following error: An error occured while reading files or writing files to disc. The disc may be full or there may be a problem with the source media. I am running PSE10 on a iMac using OS X 10.7.3, my Mac has a 1TB hardrive of which about 150GB is used. I get this error when trying to delete a file out of the Organizer. The software worked fine until I installed it on my laptop, also a Mac, and tried to share files.

Hmm. What happens if you disable sharing, just as a test?
I don't think you can share organizer photos that way, since your versions don't really exist as images, just as a set of directions to organizer for recreate that state of your editing when needed, and you can't run organizer on a network drive, which is pretty much what you're trying to do if you mean you have PSE installed on the other computer and are tryng to use the same catalog for both.

An error occurred while reading files or writing files to disc. The disc may be full or there may be

Does anyone know why I get this error message in PSE9 on a mac computer?
An error occurred while reading files or writing files to disc. The disc may be full or there may be a problem with the source media.
I cant put titles on pictures or delete them from the hard drive, etc.
Please help.
Thank you!

Okay. I would suggest going to your username>library>preferences and deleting everything that is anything like com.adobe.Elements Organizer.plist. You will have more than one of these, one with the version number and possibly one with UUID in it. Also delete any lockfiles with the same names. While you're in username>library, also delete any saved application states for the organizer or PSE from your saved states folder. Then repair permissions and try again.
The username>library folder is hidden in lion. To make it visible, in the Finder click the Go menu and hold down the Option key. It will appear below the little house for your user account.

An error occurred while verifying disc.

Similar Messages

Maybe you are looking for