Analog Devices ADIS16350 High Precision Tri-Axis Inertial Sensor: SPI LabVIEW FPGA IP

Hi,
will i be able to get the SPI LabVIEW FPGA IP available in the website in Labview 8.5? I have also attached the folder here for your convenience
Thank you!
Regards,
Chathuri
Attachments:
adis16350_all.zip ‏786 KB

There's 8.0.1 SPI available in http://zone.ni.com/devzone/cda/epd/p/id/3458
You can open it with 8.5 also.

Similar Messages

Serial port communication to read from an inertail sensor from Analog Devices

Hi, I have an Inertial Sensor ADIS16350 by Analog Devices. My motive is to read continuous data from the sensor. The sensor firmware has specific commands as follows:
at wil return OK
ra will read once from sensor
ca will read continuously from sensor
When I try this in the hyperterminal it all works fine.
However I tried in labview the same method. However when I send any of this commands the front panel shows an Error message. Meaning if I send 'at' command, instead of returning 'OK' I get 'ERROR: 61-74-30-43-error' I believe this is an error sent by the sensor firmware. However just to test the system, I tried sending the 'continuous acquisition' command from my LABVIEW program, close LabVIEW, Open Hyperterminal. To see the data is being received at the Hyperterminal.
Has anyone come acroos such a situation? Your feedback is greatly appreciated.
Thankyou!
Chathuri
Solved!
Go to Solution.

Chathuri,
Suggest you try using NISpy to monitor the port. With NISpy running, use Hyperterminal to send command. Shut down Hyperterminal to free up the port and try your LV vi. Now you can look at the NISpy log and compare what the two programs are doing.

Do we have Digital to Analog converter with high current output?

Do we have Digital to Analog converter with high current output? I need 8 channels and each channel has at least 100mA current output.Thanks!

I have never heard of such a device. You will probably need to follow the D/A with an amplifer for each channel.
What is the voltage range and speed required? Any special protection requirements (such as current limiting)?
Lynn

Problem in installing "audio device on high definition audio bus"

i have cq40 144tu laptop
i downgrade to XP with the nice tutorial posted on this forum.
my laptop S/N - [text removed for privacy]
P/N FZ736PA#ACJ
I M GETTING PROBLEM IN INSTALLING AUDIO DEVICE ON HIGH DEFINITION AUDIO BUS
i have tried sp39671 which was sugges in that tutorial but that not work

The other sound driver is Intel HDMI driver, it is bundled in Intel GMA driver.
Update your BIOS to the latest one and do a clean instalation of XP-SP3 then you dont need devcon utility.
See XP downgrade guide for futher detail, here
Pavilion DV2922TX, XP-SP3 32bit, Intel T5750 2.0Ghz, Nvidia Geforce 8400M GS with 128MB, 4GB 667 DDR2, 250GB HDD

WXP on Portege R700-1F7 - missing Audio device on high definition audio bus

Recently purchased this laptop, need to downgrade to windows xp, wiped disc, installed fresh copy of win xp sp3 and installed drivers form Toshibas website, however device manager still reporting the driver for
Audio device on high definition audio bus is missing
Tried reinstalling audio and chipset drivers again, tried windows update and driver genius, nothing is resolving driver issue, can anyone let me know what the missing driver is and where I can download it?
Thanks in advance

Hello
I dont have this Portege model but here is WXP install order and please install all stuff following this install order. Maybe this will help you to get working all hardware components and preinstalled software as well. Please post some feedback.
Windows XP SP3
Synaptics Touch Pad Driver 15.0.12
PatchFiles USBKB918005.reg
USB3.0 Driver 1.0.20.1
USB-Serial Driver 1.00.000
Sun Java2 Runtime Environment 1.6.0_20
TOSHIBA Assist 1.03.00_I
TOSHIBA Skins for Media Player 1.00.1121
TOSHIBA Security Assist 1.2.2
Trusted Platform Module 3.60.2071.00
TPM Driver v2.1.1.0
Intel Chipset SW Installation Utility 9.1.1.1024
Intel Management Engine Interface 6.00.40.1215
Intel AMT Software 6.00.40.1215
Intel Display Driver 6.14.10.5258
Realtek Audio Driver 5.10.0.6083
Intel LAN Driver 14.6(IN146AAW7C)
Ricoh Card Reader 2.09.03.01
Wireless LAN
TOSHIBA Common Module V6.07.01
TOSHIBA Web Camera Application V1.1.2.13
Authentec Fingerprint Driver 3.0.1.149
PatchFiles2 DisableFingerprintSelectiveSuspend
Finger_print_restart V1
TOSHIBA Smooth View 2.0.0.25
TOSHIBA PC Diagnostic Tool 3.2.15
TOSHIBA Controls v3.37.4310
TouchPad On_Off Utility 2.5.4.0
Bluetooth Stack for Windows by Toshiba v7.10.14_XP_SE(T)
ConfigFree 5.90.18
TOSHIBA Mobile Extension V3.94.00.XP
TOSHIBA Password Utility V2.01.10
TOSHIBA Utilities 4.30.29
TOSHIBA HDD Protection 2.3.0.1
TOSHIBA HDD_SSD Alert 3.1.0.6
TOSHIBA Hotkey Utility for Display Devices V3.7.0.0
TOSHIBA Display Device Change Utility V3.4.0.0
TPSReg REG
TOSHIBA Power Saver 7.14.00
Timeout15 D15Sec
129 Wireless Hotkey 3.0.0.9
TOSHIBA PC Health Monitor 1.6.2.0
TOSHIBA Sleep Utility 1.4.1.2
TOSHIBA DVD PLAYER V2.50.1.07-A
TOSHIBA Service Station 2.1.40
PatchFiles3 AHCI-IDEREG-1.0-ENG
TOSHIBA Network Device ID Registry Setting Tool 3.0.32.4-7
PatchFiles4 PatchFiles_WOL_1.0.0

How to Add Analog Devices Components to MultiSim v.9

I was wondering if it is possible to add the new Analog Devices component libraries to MultiSim Version 9.1.221 by a drag and drop in windows, or possibly through an import function in MultiSim.
If one were to download the MultiSim Analog Devices version 10.x and already have a licensed professional version of MultiSim 9.1.221 is this possible?

Hi,
It is not possible to import components from a higher version of Multisim into a lower one. You can import older databases into newer version. Take a look at the tutorial below:
http://ae.natinst.com/public.nsf/web/searchinternal/7219964f364425fe862576c1000ba7e1?OpenDocument
Hope this helps.
Regards,
Tayyab R,
National Instruments.

When installing Analog Devices Multisim: invalid win32 application

Hi,
I'm trying to install Analog Devices' version of Multisim, however when I do it instantly responds with a "is not a valid win32 application" error message. Any ideas on how to fix?
Cheers,
Phil
Solved!
Go to Solution.

I haven't heard of this error before, so some extra information would be helpful.
What version of Windows XP are you running? Do you have Service Pack 2 or Service Pack 3?
When is this error happening? Is this happening when you run the installer or when you run Multisim?
Last, when this type of error occurs, Windows usually logs some additional information about the error that can be helpful in diagnosing the problem.
1. Open the Control Panel
2. Double click on Administrative Tools. Then double click on Event Viewer.
3. On the left, there are several items. Look select these and look for any Errors at the same Date and Time you tried to start the program (there will be a lot of unrelated items but they are in order with the most recent at the top). For each Error that has the same Date and Time
Double click on the item.
Copy and paste the Description into your reply.
Garret
Senior Software Developer
National Instruments
Circuit Design Community and Blog
If someone helped you, let them know. Mark as solved or give a kudo.

Has anyone developed drivers for ADMC401 from Analog devices?

I am trying to develop an interface to an ADMC401 which uses ADSP2171 processor. I am wondering if any one has developed any drivers for this.

Hello,
I did a quick web search and was unable to find any 3rd-party LabVIEW drivers for this device. Your best bet is to check with Analog Devices and see if they have any LabVIEW drivers for this hardware.
I wish you luck in your search. Have a pleasant day.
Sincerely,
Darren N.
Darren Nattinger, CLA
LabVIEW Artisan and Nugget Penman

VISA read raw data from USB board Analog Devices ADISUSBZ

Hi
I am trying to use VISA to read the raw data from a USB dev board (Analog Devices ADISUSBZ). but always get below errors
"BFFF003A Unable to start operation because setup is invalid."
what I did.
1) uninstalled and deleted the origanl USB driver for ADISUSBZ
2) plugin ADISUSBZ USB Dev board, windows see a unknow device, using VISA Driver Wizard to create a USB driver inf file for ADISUSBZ
3) installed the new driver which VISA Driver Wizard created, restarted computer, ADISUSBZ is identified and loaded with VISA USB driver. also showing "This device is working properly."
4) Run Measurement & Automation Explorer, in the Devices and Interfaces list, I can see that USB device which is the ADISUSBZ. but the name is
Unkown USB0::0x0456::0xEF02::NI-VISA-40002::RAW (the VID PID tell me, it is the ADISUSBZ USB Dev board)
5) Open VISA Test panel -> View All Settable Attributes, I got below data, where VI_ATTR_USB_BULK_IN_STATUS = -1 (not active???)
VI_ATTR_TMO_VALUE = 2000
VI_ATTR_MAX_QUEUE_LENGTH = 50
VI_ATTR_TERMCHAR = 0x0A
VI_ATTR_TERMCHAR_EN = VI_FALSE
VI_ATTR_IO_PROT = 1
VI_ATTR_SUPPRESS_END_EN = VI_FALSE
VI_ATTR_USB_MAX_INTR_SIZE = 1
VI_ATTR_USB_CTRL_PIPE = 0x0000
VI_ATTR_USB_BULK_OUT_PIPE = 0xFFFF
VI_ATTR_USB_BULK_IN_PIPE = 0xFFFF
VI_ATTR_USB_INTR_IN_PIPE = 0xFFFF
VI_ATTR_USB_ALT_SETTING = 0
VI_ATTR_USB_BULK_OUT_STATUS = -1
VI_ATTR_USB_BULK_IN_STATUS = -1
VI_ATTR_USB_INTR_IN_STATUS = -1
VI_ATTR_USB_END_IN = 5
6) Basic I/O -> viRead , set count to 1 or default 1024 , execute
return status is always BFFF003A
I searched in error list, it says
"BFFF003A Unable to start operation because setup is invalid."
any idea what is wrong? help
BTW, the ADISUSBZ USB board works fine, test with its own software, it is not hardware faulty
Eric

Hi Eric
I have a few questions for you as well as a number
of likes that will help you.
What software are you using NI VISA with is it just
Measurement and automation explorer ?
Which version of NI VISA are you using?
Which operating system are you using?
In measurement and automation explorer is there a
yellow question mark against the device?
I would advise reading the likes below if you have
not already creating the VISA driver again checking the manufacture ID and
model code if these options are available to you.
The following link will help you with the VISA
http://digital.ni.com/public.nsf/websearch/E3A2C4FE42D7ED0D86256DB7005C65C9
This tutorial gives a step by step guide on how to
create a VISA driver.
http://zone.ni.com/devzone/cda/tut/p/id/4713
The Difference between USB Raw Control and USB Raw
Bulk
http://digital.ni.com/public.nsf/allkb/400D6EAB5CFE1C6B86257395005F5D48?OpenDocument
Can VISA Read be used to read USB Interrupt Data?
http://digital.ni.com/public.nsf/allkb/D38E5A65DA54C9A2862571E900810FEA?OpenDocument
Regards
Robert
National Instruments UK & Ireland

Using USB-8451, and AD7747 from Analog Devices to measure capacitance and convert the capacitance to digital output

Hello,
I am new to LabView and data aqusition. I have LabView 8.5.1 installed on my laptop, and I studied the Getting Started document of LabView, except the data aqusition chapter.
I have microfabricated a differential capacitive sensor, and now I want to test the capabilities of my sensor.
After asking NI engineers, I have been suggested to use USB-8451 with AD7747 (24-Bit Capacitance-to-Digital Converter) from Analog Devices because AD7747 has I2C serial interface.
I have ordered USB-8451, AD7747, and Evaluation Board for AD7747. And I am waiting for them.
Are there any suggestions about how to connect my differential capacitive sensor to AD7747, and eventually to USB-8451?
You may want to know some further information to answer my question:
*The sensor is similar to the sensor on pages 501, 514, and 515 of "Microsystem Design" book from author Stephen D. Senturia.
*The datasheet for AD7747 can be reached from this link: http://www.analog.com/static/imported-files/data_sheets/AD7747.pdf
*My purpose is to make a very precise and accurate "displacement measurement micodevice" by using "the change in the capacitance" during the motion of the mobile fingers of the sensor.
As an initial challenge for myself, I will feel satisfied if I can measure the capacitance change in my sensor when I apply an external mechanical disturbance to my sensor. For example, there must be a change in capacitance if I just swing my hand from top of the sensor region.
I am looking forward for your reply,
Thanks in advance,
Sincerely,
sriverfxtr

Hi Aaron,
Here you go, this is made with a USB-8452.
When you run the code tick the power en dac enable box on.
Maybe you can help me with my problem, I want to use a fiber to sense light from a led.
Do you use any fiber hardware with the TCS3414?
gr,
Attachments:
TCS3414.vi ‏63 KB

Problems with sound drivers - audio device on high definition audio bus

i turned on my computer one day and the sound was gone. no "speaker" icon in the lower right-hand corner of the screen; no choices available via the "control panel: sounds and audio devices" icon. when i went to device manager, i saw "audio device on high definition audio bus" had a yellow exclamation mark. i saw some sites suggested downloading the realtek high definition audio, but that didn't seem to work -- and now i don't see the audio device on high definition audio line either.
any ideas? from what i've read, i gather this is a somewhat common problem but no solid way to fix this. i know something similar has happened to me a year ago but i was able to fix it somehow.
Solved!
Go to Solution.

Hello,
Have you tried installing the latest audio device drivers for your ThinkPad? If so, did that solve the problem?
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

Audio Device on High Definition Audio Bus Prob

I installed a Sound Blaster Audigy SE and it's drivers, but when I restarted my computer Windows told me?that it'sdetected even more hardware. (Audio Device on High Definition Audio Bus) I tried using the drivers included with the Sound Blaster CD for it, but they didn't work. Regardless, my sound works and I can see "Sound Blaster Audigy" under sound, video and game controllers in Device Manager; however, I also see "" listed under other devices with a yellow question mark next to it. Does anyone know what's wrong?
Thank you for your time.Message Edited by YSM on 02-7-200804:33 PM

Hello,
I have a feeling that this device refers to your onboard soundcard. You haven't mentioned which motherboard you have, but I suppose it's one which features a high definition audio codec, probably a Realtek one.
So, the solution to your problem should be the following:
If you have english windows, put the motherboard's CD into the dri've an go to the "sound" or similar named folder and look for a "microsoft UAA something" folder, containing a KB888.exe file. Install this hotfix and then install the audio drivers of the motherboard (you will have 2 operational soundcards afterwards).
There is a small variation to that, if your windows are non-english. Motherboard manufacturers usually include only the english version of the UAA hotfix on the CD. In that case, you must download the multilanguage package of the hotfix. Unfortunately, microsoft doesn't offer it for download, so go to www.gigabyte.com.tw and look for any motherboard with onboard HD audio. Gigabyte offers the multilingual package for download.
Alternati'vely, you can disable the onboard audio from your BIOS and use only your Audigy

Video demo of Analog Devices dual 2.5Gsamples/sec ADCs running at 5Gsamples/sec at Embedded World 2015

Last year, Analog Devices announced the 2.5Gsamples/sec AD9625-2.5 ADC and the $750 AD-FMCADC2-EBZ FMC module. (See “Analog Devices kicks sample rate up a notch on AD9625 ADC: now 2.5Gsamples/sec”.) The company demonstrated this FMC module at this year’s Embedded World 2015 with two ADCs running in interleaved mode for an aggregate sample rate of 5Gsamples/sec. The FMC card is plugged into a Xilinx Virtex-7 VC707 Eval Kit and communicates over 16 lanes of JESD204B each running at 6.5Gbps. The on-board Virtex-7 XC7VX485T FPGA’s DSPs and high-speed logic fabric are used to interleave the readings from the two ADCs on the FMC card.
Here’s a short video showing the demo:

It used to be in there (id 226635 is the last one with it); should I clean it up a bit and put it back with a bit more of a disclaimer?

XP 64 Bit - Audio Device on High Definition Audio Bus - Driver needed!!

This concerns a Macbook Pro
Hi, I have followed many tutorials on the internet to help install XP 64 bit on my bootcamp partition.
I know this is not advised due to the lack of driver support but I have 8GB of RAM and want to utilise it all on my favourite OS.
Things have gone well and almost all devices have the correct drivers installed.
There is one exception to this:
I installed the RealTek drivers from the high definition setup exe and Device Manager simply tells me I have codecs installed for audio and video etc. the problem is that under 'Other Device' I have 'Audio Device on High Definition Audio Bus'
Due to this, my speakers do not function and no sound tray icon exists. I have tried many, many different drivers so far and have had no luck.
My macbook is a 2.26GHz model and I think is known as the 5,5 model of MBP.
If anybody could offer assistance it would be widely appreciated.
Thanks, Chris

I just solved the problem
The four devices are NVIDIA High Definition Audio that the driver is included in NVIDIA Display Driver installer from lenovo.
I should install Microsoft UAA High Definition Audio driver first before installing the NVIDIA Display Driver. What I did before was I installed the NVIDIA Display Driver first before installing UAA High Definition Audio driver, that's why the four NVIDIA High Definition Audio driver weren't detected, hence the drivers weren't installed.
So the solution for Windows XP SP2 users is just simply reinstall the NVIDIA Display Driver. If you install SP3, it already has the UAA Audio driver.

[P965 Neo-F v2] Audio Device on High Definition Audio Bus

Hi,
I've some problem installing the onboard sound card (Realtek).
A first part of the driver is installed correctly but a second part is always detected (Audio Device on High Definition Audio Bus) and failed to install.
I've processed as followed:
1 - fresh installation Windows XP
- install INFfrom CD
- install network from CD
- install sound from CD
2 - fresh installation Windows XP
- install INF (latest driver on USB Key)
- install network (latest driver on USB Key)
- install sound (latest driver on USB key)
I think the unknown detected peripheral has to do with microsoft (there's a patch included with Sound Realtek drivers)
Any help is welcome
Thanks

Quote from: nightmare99 on 12-September-07, 23:16:35
Yes its the Microsoft UAA High Definition Bus driver. how are you installing yoiur sound driver are you running the realtek setup? If so it should install the ms patch.
I'm using the realtek setup and yes, the patch is installed.
I've also tried to force the microsoft bus driver (by choosing manually the driver) without success

Analog Devices ADIS16350 High Precision Tri-Axis Inertial Sensor: SPI LabVIEW FPGA IP

Similar Messages

Maybe you are looking for