Analog Devices RTI-800

Hi
We have several RTI-800 (older AD boards), and we want to update the control
software to LabView.
I'm looking for info on VIs for the RTI-800 in particular, or similar boards
in general.
Simple AD and DO are all we need.
Anybody have a VI, or a possible source for one?

Hi, thanks for the responses. I did a search on the 815 and 802, but I must admit, I neglected to search the forums for the AC28. All 3 cards are still available (although AD has discontinued their cards UEI manufactures replacement units) The company I work for has these cards in several test rigs, and I'm looking at options of modernising the PC & control software without incurring the cost of a complete control system retrofit (the current control software is DOS based). In view of performance & accuracy it probably makes sense to upgrade the cards and signal conditioning, but In the short term that would be a difficult proposition.
We also have other test machines which use labview, AD 5B signal conditioning, and Siemens profi connected I/O. Ideally if we were to look at a complete retro I would be keen to commonise as much equipment as possible. However, while the current hardware remains available, and performs adequately It will be quite difficult to justify.
SSK: Also, I would be interested in the code that was you utilised, if you could dig it up that would be a great starting point.
Mark: Thanks also for your post. I'll look into the driver kit, and most likely ask NI if they would consider writing some drivers at some stage.
Some links:
AC28:       http://www.opto22.com/site/pr_details.aspx?item=AC28&qs=100110021006,,,0,6
RTI-815:   http://www.ueidaq.com/products/pci-data-acquisition/uei-800/uei-815-32/
                 http://www.ueidaq.com/products/pci-data-acquisition/uei-800/uei-815/
RTI-802: http://www.ueidaq.com/products/pci-data-acquisition/uei-isa-ao/uei-802-8/

Similar Messages

Drivers for Analog Devices RTI-815

Hi,
Does anyone know where I can find Labview drivers for an Analog
Devices RTI-815 card, if they exist?
The card came out of a Haake Rheocord System 90. The old
controller for it is a 286; we'd like to replace it with a newer computer
and software written in Labview. Thanks for your help.
-Nathan

Hi, thanks for the responses. I did a search on the 815 and 802, but I must admit, I neglected to search the forums for the AC28. All 3 cards are still available (although AD has discontinued their cards UEI manufactures replacement units) The company I work for has these cards in several test rigs, and I'm looking at options of modernising the PC & control software without incurring the cost of a complete control system retrofit (the current control software is DOS based). In view of performance & accuracy it probably makes sense to upgrade the cards and signal conditioning, but In the short term that would be a difficult proposition.
We also have other test machines which use labview, AD 5B signal conditioning, and Siemens profi connected I/O. Ideally if we were to look at a complete retro I would be keen to commonise as much equipment as possible. However, while the current hardware remains available, and performs adequately It will be quite difficult to justify.
SSK: Also, I would be interested in the code that was you utilised, if you could dig it up that would be a great starting point.
Mark: Thanks also for your post. I'll look into the driver kit, and most likely ask NI if they would consider writing some drivers at some stage.
Some links:
AC28:       http://www.opto22.com/site/pr_details.aspx?item=AC28&qs=100110021006,,,0,6
RTI-815:   http://www.ueidaq.com/products/pci-data-acquisition/uei-800/uei-815-32/
                 http://www.ueidaq.com/products/pci-data-acquisition/uei-800/uei-815/
RTI-802: http://www.ueidaq.com/products/pci-data-acquisition/uei-isa-ao/uei-802-8/

Labview driver for Analog Device cards RTI 800 series

Hello,
I'm Mathieu Meisser, from EPFL Lausanne - microtechnique.
I'm working for a company, that produces
laboratory PC-controlled analysers, sold all over the world.
we are searching for the Labview drivers for the I/O analog Device
cards RTI 815/817 in order to developp a new intrumentation control
with Labview 5.0.
It's very important to know if any kind of these drivers are
still avaible and work properly.
please let me know as soon as possible if you know
something about this !
thank you for your cooperation !
Mathieu Meisser
Sent via Deja.com http://www.deja.com/
Share what you know. Learn what you don't.

Hi Mohan,
Unfortunately there isn't a instrument driver specific to that device. What you could do though is use our NI-VISA driver and try to communicate with the instrument over serial (I assume it uses serial for communication) There are examples in the Example Finder (Help>>Find Examples) that ships with LabVIEW that will demonstrate some functions you can use. I hope this helps out.
Regards,
Michael
Applications Engineering
National Instruments

Activate a call forward with a Third-party SIP Device or with a analog device

Hi,
In a CUCMv9, how i can activate a call forward (all, busy, no anwser...) with Third-party SIP Device or with a analog device connected to a fxs?
I want to activate a call forward like a Alcatel or Aastra PBX with a code.
For exemple, i pick up the phone, with the code *95 followed by the destination number and hangs up the phone. And use the #95 for désactivate this call forward.
It's possible?
Thanks.

No codes for 3rd party SIP phones, no way to do it. Or for that matter, not even for Cisco Phones, other than CFA.
Anything besides CFA needs to be done via CCMadmin or CCMuser for any kind of phone.
For FXS that's only doable if you're running SCCP
http://www.cisco.com/en/US/partner/docs/ios/voice/fxs/configuration/guide/fxssccpsplmft.html
HTH
java
if this helps, please rate
www.cisco.com/go/pdihelpdesk

Can I merge database of multisim analog device version in multisim?

Can I merge database of multisim analog device version in multisim?
If yes, please tell me how. Thx!
I saw the file named "MSCOMP_S.prd" in the folder:
C:\Program Files\National Instruments\Multisim Analog Devices Edition 10.0\database

Hi Zenith,
The databases between the two products are not compatible and therefore cannot be merged. This database was created specifically for the Analog Devices Edition. Merging two "Master" databases is also not possible since the merge utility will only allow merging two "User" or "Corporate" databases.
Message Edited by M.I. on 12-03-2007 09:34 AM
M.I.
National Instruments
EWB Group.

Which is a dual 2-bit bistable transparent latch IC in multisim analog devices edition

I need an equivalent IC for CD74HC75, which is a dual 2-bit transparent latch IC, for a project simulation. Cant find it in the Multisim reference guide.
Any suggestions??
Solved!
Go to Solution.

emind,
Hello, in the Multisim Analog Devices Evaluation Edition, you will find a D_Latch under the TIL family of parts (use 2 with EN tied together for a dual latch) that you can use for generic simulation purposes. If you need a specific latch from a manufacturer or specific logic family that might be challenging (we have a few in the PRO version or you can add some external circuitry to the TIL part to mimic the behavior of a particular logic family).
The TIL parts (generic digital I/O) are located here: Misc Digital (group) -> TIL -> D_LATCH.
I created a simple interactive circuit with a probe so you can observe the behavior to see if it will meet your simulation needs.
Regards,
Pat Noonan
National Instruments
Attachments:
bistable latch (ADI_edition).ms11 ‏36 KB

Trouble activating Multisim component evaluator Analog Devices Edition Version

I downloaded Multisim component evaluator Analog Devices Edition Version
13.0.. I’m having the same problem that I had last time I downloaded something
from NI. (Unactivated license). I think this is because of the tight security
where I work. The solution last time (after a lot of time and back and forth
emailing was to send me the activation code and I typed it in manually. (I
pasted that email below).
Thanks,
Brian
Brian Healey – Electrical Engineer – ISR Systems
UTC AEROSPACE SYSTEMS
7 Technology Park Drive, Westford, MA 01886 U.S.A.
Tel: +1 978 490 2148 Mobile: +1 978 846 5918
[email protected] www.utcaerospacesystems.com
From: [email protected] [mailto:[email protected]]
Sent: Friday, May 24, 2013 1:47 PM
To: Healey, Brian W UTAS
Subject: RE: [External] Re: (Reference#2014565) Phone Support E-Mail
Note: Your reference number is included in the subject field of this message.
It is very important not to remove or modify this reference number, or your
message may be returned to you.
Hi,
Open the License Manager again and try to activate Multisim, but this time
select the option to activate through a 20 - characer code.
Activation Code:
BS9P-HW36-4Z8Y-DJWM-C9N4
Let me know if this works.
Kind regards,
Miguel Vesco
Applications Engineer
National Instruments
http://www.ni.com/support

Hi Brian,
Since you have a new version the software needs to be reactivated with a new Activation Code. I will send you an email via our support system for further details.
Regards,
Fernando D.
National Instruments

How do I add Analog Devices symbols and footprints to component database?

Hi,
Analog Devices conveniently has a library of their component symbols and footprints for Ultiboard and Multisim. How can I add these to the library?
Is it a drag and drop thing? If so what is the folder location?
If I go thru the available database interface it doesn't allow for selecting footprints outside of the existing library and adding them.
In ultiboard I can open the footprints, but 'save to database' is not an option available.
thanks
Ryan

I am not sure which file you downloaded, but I downloaded the Ultiboard Zip file (the small 3KB one). Each footprint is an individual footprint and apparently must be added manually to the database in Ultiboard.
How to do this? In Ultiboard, Extact them to a location on your drive and double click the footprint and it will load onto the screen like a normal board would. Now you have to goto DATABASE>DATABASE MANAGER. Once there you right click on USER DATABASE and add a family like say TRANSITORS. Then highlight your new family by clicking on it. Then goto the very top of the and you will see a little yellow "+" . click that and it will give you the option to add a new part from the current design to the user database. That is all you need. The footprint will be in the user database.
The next step is to assign it to the component in Multisim and you will have to refer to a turtorial on the NI Site in order to do this. I will post a link to it once I find it.
I do not know about the other file. Most of the time there are .PRZ files that the only thing you have to do is to go into the database manager of Multisim and select the user database. This will give you the option to do an import. If your files are a .PRZ file then you will be able to import using this option.
I hope some of this helps a little
Kittmaster's Component Database
http://ni.kittmaster.com
Have a Nice Day

Maxium calls on Analog devices CCM v.7

I know this is probably a silly question but I would like to verify. Devices such as ATAs and VG248s that converts calls to analog, I've notice have only maximum call of 2. Is there a way around this or another way I have analog maximum calls set to 4?

The help document for the directory number settings page says:
"The default specifies 4. If the phone does not allow multiple calls for each line, the default specifies 2."
Analog devices do not support multiple calls per line. There is no way around this limitation to my knowledge.
Hope this helps.
Brandon

How to Add Analog Devices Components to MultiSim v.9

I was wondering if it is possible to add the new Analog Devices component libraries to MultiSim Version 9.1.221 by a drag and drop in windows, or possibly through an import function in MultiSim.
If one were to download the MultiSim Analog Devices version 10.x and already have a licensed professional version of MultiSim 9.1.221 is this possible?

Hi,
It is not possible to import components from a higher version of Multisim into a lower one. You can import older databases into newer version. Take a look at the tutorial below:
http://ae.natinst.com/public.nsf/web/searchinternal/7219964f364425fe862576c1000ba7e1?OpenDocument
Hope this helps.
Regards,
Tayyab R,
National Instruments.

When installing Analog Devices Multisim: invalid win32 application

Hi,
I'm trying to install Analog Devices' version of Multisim, however when I do it instantly responds with a "is not a valid win32 application" error message. Any ideas on how to fix?
Cheers,
Phil
Solved!
Go to Solution.

I haven't heard of this error before, so some extra information would be helpful.
What version of Windows XP are you running? Do you have Service Pack 2 or Service Pack 3?
When is this error happening? Is this happening when you run the installer or when you run Multisim?
Last, when this type of error occurs, Windows usually logs some additional information about the error that can be helpful in diagnosing the problem.
1. Open the Control Panel
2. Double click on Administrative Tools. Then double click on Event Viewer.
3. On the left, there are several items. Look select these and look for any Errors at the same Date and Time you tried to start the program (there will be a lot of unrelated items but they are in order with the most recent at the top). For each Error that has the same Date and Time
Double click on the item.
Copy and paste the Description into your reply.
Garret
Senior Software Developer
National Instruments
Circuit Design Community and Blog
If someone helped you, let them know. Mark as solved or give a kudo.

Analog Devices model update for AD version

Downloaded 'ADI_All_MultiSim_Symbols.zip' from AD website. How do I get them into multisim analog device edition?
Solved!
Go to Solution.

I have MSim-Analog Device edition only. Can someone database merge, or if you already have it, try to extract a SPICE netlist and post for the ADM4073? I've attached the .prz file from Analog Devices.
Thanks
Attachments:
ADM4073TWRJZ-REEL7.prz ‏296 KB

Analog Devices 6b12

Is there a driver for a Analog Devices 6B12 that will work in LabVIEW 6.0? The only driver that I have found is for 7.0.

http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=E3B19B3E9208659CE034080020E748...

Analog Devices Edition: Current feedback amplifier models not working

Hi, I'm using the Analog Devices version of Multisim and have problems simulating their current feedback amplifers. For example, I want to use the AD8000 as an inverting transimpedance amplifier, basically run a current into the inverting input, ground the non-inverting input, and chose the feedback resistor to be the transimpedance. I want to make sure that I can use feedback resistors between 100 and 2000 Ohms to convert negative current pulses to positive voltage pulses, but I can't get anything to work, even with the recommended feedback resistor values. With a current input I get negative rail saturation, while with a voltage input I get a step output.
Thank you.
Attachments:
AnalogInputCFA.ms10 ‏106 KB

Hi there,
I think I figured out why your circuit isn't working. It has to do with the treatment of the dedicated feedback output pin that exists on your amplifier. While this pin and the main output pin both exist on the physical package and are electrically connected, this isn't the case in Multisim. The feedback pin in Multisim exists on the schematic only, it doesn't actually have any simulation functionality. So, as a workaround, I suggest that you connect the feedback path to the output pin instead of the dedicated feedback pin. You would never do this in real life, but for simulation, it will work fine.
Thanks for pointing this out. We will look into this problem and have it fixed in the future.
Yi
Software Developer
National Instruments - Electronics Workbench Group

Has anyone developed drivers for ADMC401 from Analog devices?

I am trying to develop an interface to an ADMC401 which uses ADSP2171 processor. I am wondering if any one has developed any drivers for this.

Hello,
I did a quick web search and was unable to find any 3rd-party LabVIEW drivers for this device. Your best bet is to check with Analog Devices and see if they have any LabVIEW drivers for this hardware.
I wish you luck in your search. Have a pleasant day.
Sincerely,
Darren N.
Darren Nattinger, CLA
LabVIEW Artisan and Nugget Penman

Analog Devices RTI-800

Similar Messages

Maybe you are looking for