Analog Lines to E1 DID/DOD configuration need for CCME

Dear,
I have one of our remote site have the following configuration:
* 2 X CCME running on C3845.
* 1 X CUE installed on one of the C3845
* Around 70 IPT (7910, 7941 & 7941) registres in the CCME.
* 8 * analog lines connected to FXO ports that provide land lind connectivity for the site.
* 4 * FXS ports to provide FAX.
and becasue of unstability issue with the out/ingoing call we requested 4 X voice E1 DID/DOD. and want to know what is the required configuration to consider in migrating my remote site.
regards

Hello, thanks for your responses helped me very much.
I have the commands and errors completes:
When I enter the command:
ds0-group 0 timeslots 1-15,17-25 type r2-digital r2-compelled ani into the controller e1, I receive this error:
% Not enough DSP resources available to configure ds0-group 0 on controller E1 0/0/0
% The remaining dsp resources are enough for 20 time slots.
% For current codec complexity, 1 extra dsp(s) are required to create this voiceport.
This the inventory in the router:
GW-VOSS(config-controller)#do sh inv
NAME: "2821 chassis", DESCR: "2821 chassis" PID: CISCO2821         , VID: V05 , SN: FTX1336AHFS
NAME: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1" PID: VWIC2-1MFT-T1/E1 , VID: V01 , SN: FOC133129NF
NAME: "2nd generation two port FXO voice interface daughtercard on Slot 0 SubSlot 1", DESCR: "2nd generation two port FXO voice interface daughtercard"PID: VIC2-2FXO         , VID: V02 , SN: FOC13332NDZ
NAME: "3rd generation two port FXS DID voice interface daughtercard on Slot 0 SubSlot 2", DESCR: "3rd generation two port FXS DID voice interface daughtercard" PID: VIC3-2FXS/DID     , VID: V01 , SN: FOC132526S0
NAME: "PVDMII DSP SIMM with four DSPs on Slot 0 SubSlot 4", DESCR: "PVDMII DSP S IMM with four DSPs" PID: PVDM2-64          , VID: V01 , SN: FOC13341ZE1.
I have the transcoding:
dspfarm profile 1 transcode
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 15
associate application SCCP
I have CUCM 7.0, Contac Center 6.0, SIP trunk, 1 E1.
I need another PVDM card? The router can be have two PVDM card? Which PVDM card you recommend ?
Regards

Similar Messages

Configurations needed for Proxies.

What are the all configuration steps for using a Server proxy.?

Hi Soumyasanto Sen ,
Proxy generation converts non-language-specific interface descriptions in WSDL into executable interfaces known as Proxies. Depending on the target programming language, you choose one of the following:1. Java Proxies. or 2. ABAP Proxies.
We can interface to XI through proxies. From WAS 6.20, proxy generation feature enables application systems to communicate with XI using proxies. Proxy generation enables you to create proxies in application systems. Proxies encapsulate the creation or parsing of XML messages and the communication with the relevant runtime components required to send or receive the messages.
There are two types of Proxies.
1. Java Proxies.
2. ABAP Proxies.
Java proxies are used when java applications needs to send and receive data and ABAP proxies are used when ABAP applications needs to send and receive data.
The following websites contained detailed explanation (PDF & PPT docs) on Configurations needed for Proxies:
Proxy Generation
http://help.sap.com/saphelp_nw04/helpdata/en/86/58cd3b11571962e10000000a11402f/content.htm
ABAP Proxy Runtime
http://help.sap.com/saphelp_nw04/helpdata/en/02/265c3cf311070ae10000000a114084/content.htm
To activate ABAP proxies
/people/vijaya.kumari2/blog/2006/01/26/how-do-you-activate-abap-proxies
Detailed step-by-step solution for ABAP proxies in XI
/people/ravikumar.allampallam/blog/2005/03/14/abap-proxies-in-xiclient-proxy
ABAP Server proxies
/people/siva.maranani/blog/2005/04/03/abap-server-proxies
Debugging of Inbound ABAP proxies
/people/stefan.grube/blog/2006/07/28/xi-debug-your-inbound-abap-proxy-implementation
File to R/3 via ABAP Proxy
/people/prateek.shah/blog/2005/06/14/file-to-r3-via-abap-proxy
How to push data from BI to XI using proxy
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/e698aa90-0201-0010-7982-b498e02af76b
How to push data into BW from XI using proxy
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/18dfe590-0201-0010-6b8b-d21dfa9929c9
/people/vijaya.kumari2/blog/2006/01/26/how-do-you-activate-abap-proxies
cheers!
gyanaraj
****Pls reward points if u find this helpful

Configuration needed for SOA call to create PO in classic scenario

Dear Experts,
We are working in the SAP SRM 7.01 with backend system on ecc 6.0 Enhancement pack 5. The scenario configured is classic scenario.
I want to know what are the configurations needed to use SOA calls to create a purchase order in the backend system.
In the system landscape directory, when I use the system type "ERP_3.0" for backend system, the system uses the BAPI 'BAPI_PO_CREATE1' to create a purchase order in the backend system.
When we use the system type "ERP_4.0", it does not use the BAPI 'BAPI_PO_CREATE1' to create purchase order. It tries to use SOA calls to create PO in the backend system. However, it fails to create one.
Could you please let me know what are the settings we need to do to create a purchase order in the backend system?
Thanks and regards,
Ranjan
Ranjan Sutradhar

Hi Vardhan,
Can you be a little clear? are you using PDP scenario as in your requirements are coming as PR from ECC into SRM as SC? Is this the scenario?
Regards,
Nikhil

Any special configuration needed for Print PDF?

To print as PDF is there any configuration needed to be set.

Hi,
the only thing to pay attention is when you have to print large PDF and you receive this error: AGEGTYVF.
Refer to this doc in the Oracle Support: Printing A Large OBIEE Answers Report Or Dashboard To PDF Fails With Error Code: AGEGTYVF
Regards,
Gianluca

Configuration needed for non-SAP system as Idoc sender

Hi,
We have a need to connect a non-SAP system which is sending an Idoc to XI. I understand that on the sender side, we need to create a tRFC port from the sender system with the server address of the Integration as the target host?
My question is on the PI side, are the configurations the same as a SAP system, i.e. maintaining the port in IDX1 and getting the metadata in IDX2 or will it be different?

In PI, you will need to create a port in IDX1 with the same port name as the Idoc control record when the Idoc comes from the non SAP system.
As you cannot load the Idoc metdata from your actual source, you will need to copy the Idoc metadata from a actual SAP system or from the port of another SAP system in IDX2
Also, in the Business Service / System, make sure that the logical system name is maintained as per the Idoc control record of the source.
Regards
Bhavesh

Configurations needed for distributing central contract to backend system

Dear Gurus,
I have configured central contract and getting approved in the local SRM system. Now, I need to distribute the central contract to the backend system. I have already get the PI interfaces configured using the integration scenario Central contract management.
Now, I assign the backend POrg as well as the target values for the backend contract and try to release the central contract. The central contract is getting released. However, no contract is getting created in the backend system.
I donot see any XML messages generated in the SRM system (SXMB_MONI).
Do I need to maintain some settings in the SRM system to enable the distribution of contract to the backend system?
Thansk and regards,
Ranjan

Hi,
When one creates Local Contract; there is one option named 'Distribute' on contract screen.On drop down; one mention back end system. After clicking on it; contract has been created in ECC.
If contract is not getting generated in back end; refer SAP Note: 609222.
Check whether you find any error/information message in Txn BBP_CTR_MON.
SRM Settings:
1. Implement BBP_DETERMINE_LOGSYS: Determines whether contract is to be created in SRM or ECC.
2. Assign transaction type to attribute CT_PROC_TY in Org Structure.
3. Check whether have maintained message type BLAREL, COND_A, BLAORD.
4. Assign role SAP_BBP_STAL_START_PURCHASER to process contracts.
Helpful SAP Notes: 641919, 646903
Regards,
yaniVy
reward if helps

Configuration needed for setting revaluation of activity type rates

Hi,
I'm not sure about the obligatory settings I should make in order to configure revaluation of activity type rates.
I know that I have to set sth in Plan version and that I have to fill the Activity Type master data in a different way than if I used them without revaluation.
Can you tell me about the settings I should make?
Thanks and regards,
Karol

Hi Karol
Yes u r right u need to first set in plan version and after that its the client's discipline on transaction entry that drives this requirement.
1) If the transaction data is not posted correctly then activity hours will be vague and distorts the price.
2) You can do manual activity posting but that does solve the purpose.
3) Also u can correct activity hours posted for all orders in the system during month end, this also is a huge activity depending on the number of orders
4) Now if u wish to do price calculation thru system u need to decide on two aspects
One - plan ur costs for both activity dependent and activity independent
If your cost center has more than one activity being performed u need to do either cost splitting or enter equivalence numbers while doing activity planning
5) If u wish to hve prices calcualted by system, then during month end u need to run actual cost splitting and then do actual price calculation
6) Then u need to revaluate all your orders with actual activity prices
Hope the above clarifies - do assign points as a way to say thanks

Variant Configuration / Need for a separate forum

Dear Moderators,
I have been contributing, accessing and extracting information from this forum for my projects and trainings. Recently we have added lot of new forums especially in SD, a separate forum for billing, sales etc.
On the same path, I feel that it will add immense value if a new forum for Variant Configuration is created. As this is an area which touches various modules, and various applications like configurable materials in SD, Release procedures in MM, etc, people can share all the information regarding variant configuration in a common forum like this.
May I please request you to consider this and take it forward if this makes some sense.
Any feedback on this is welcome, especially from people like Rajesh Banka, Laxmipathy etc who have been here for quite sometime in SD

I'm going to respectfully disagree.
I saw something similar at elementsvillage.com when they created a "Mac-Specific" forum. People who had questions that really had nothing to do with their Mac, for example "Can't open RAW from D7000", still put the question in the Mac-Specific forum, because they were using a Mac. As a result, the community was fragmented in ways that had nothing to do with the question. People who might have benefited from this question but didn't have a Mac and so didn't look in the Mac-Specific forum, and didn't get the answer as quickly. People who asked questions in this forum that had nothing to do with Macs wound up relying on a smaller community of experts to help solve the problem. I know I certainly never read that forum, so I didn't provide answers, nor did I learn from the information in that forum. I consider that decision to create a "Mac-Specific" forum to be a failure.

Configurations needed for Transportation Lane

Hi Gurus,
Good Day! I would like to know what are the needed configuration in R/3 and APO so transportation lane are automatically created in R/3 once Scheduling Agreement or Inforecord is CIF in APO.
Appreciate any help.
Thanks and Best Regards,
Raymond

Hi Raymond,
No Specific Configuration is required. Following are the steps required to CIF Scheduling Agreement or Inforecord to APO as TLanes.
1. Activate integration model for recieving location and issuing location or vendor for which you want to CIF the Sched. Agreement or Inforecord.
2. Activate Product-Location Integration model with the material required for Inforecord or Sched. Agreement.
3. You need to activate the Integration model with valid IR and Sched. Agreement.
The same will be CIFed to APO as external Procurement relationship/TLane. You need to assign Means of Transport if not otherwise assigned.
Hope this answers your query.
Regards,
Manjit

Configuration needed for Installing Oracle 9i-R2 on Linux Itanium

I need a specific documentation for Installing Oracle 9i-R2 on Linux Itanium server.

Oracle does not support running the 32-bit database on Itanium.64-bit Oracle database software only supports 64-bit for Itanium.
Check Metalink Note:266043.1 for details
Virag

SD-FI integration: Configuration need for invoice to create document

Hi gurus,
invoice xxx like 91446622 under company yyyy like 1000 cannot pass through to create an accounting document becuase there is no configuration between plants 1020 and 1201
T-code VFX3 company 1000
Pls suggest me the places where i can configure it.
points for sure.
thanks & rgds,
manya

Hi habib,
If you feeel this answer solve your query please reward with points.
once the billing doucment is generated in sd. Then automatcally accounting doucment will be gnerated if you would have done revenue account determinationt and release to accountg. Coming to your point once the billing doucment cancelled in sd the following accounting document you have to reverse there is no cancellation of accounting document. in fb08 you can do this things related to the following invoice. and you will get what ever the result you want. Once you reverse it there is no open item for that billing doucment. I hope u will understood the concept
Thanks & Regards
rack29

Configuration needed for SOA ,BPM,OSB,BAM

HI,
Could any one suggest best configuration System to run all SOA products parallayly as shown below..
SOA ---? (eg.2GB RAM)
BPM--?
OSB---? (1GB)
BAM---?
Database ---? (ForMeta data repository)
do we have 64 bit software for above..I could see only 32 bit version in Oracle download page?
Thanks
Sivakumar
Edited by: siva p on Jun 23, 2012 12:11 PM

Hi Siva,
I have ran all the softwares on my system with 8GB but had issues running all of them at the same time. I would say, go with 16 GB (6-8 cores) system in DEV.
SOA ---? (eg.2GB RAM)2GB for DEV
BPM--?2GB for DEV
OSB---? (1GB)2GB for DEV
BAM---? 1GB for DEV
Database ---? (ForMeta data repository)1GB for DEV (use XE database); you would require 2-3 GB if you want to run Oracle 11g DB
do we have 64 bit software for above..I could see only 32 bit version in Oracle download page?All the softwares are available in 64 bit and you can download them here: http://www.oracle.com/technetwork/middleware/soasuite/downloads/index.html
Thanks
Sivakumar
Edited by: siva p on Jun 23, 2012 12:11 PMHope this helps!
Cheers,
NJ

Sample configuration needed for MessageIDExtractor Axis handler

Hi there,
I am trying to configure the MessageIDExtractor Axis handler (java:com.sap.aii.axis.soap.MessageIDExtractor) in a SOAP Sender CC. However, the sample provided in de Axis FAQ is not enough to complete the configuration.
I want to take the value of a SOAP Header element in the payload, and reuse that as PI Message ID.
The path to the ID will be somthing like; "anamespace:A_SOAP_Header/AId"
Many thanks,
Roberto

>
yzanagi wrote:
> ....
> The instruction in the FAQ note is actually straightforward if you are familiar with the xpath notation.
>
> If it's not working, can you provide how you set these parameters and how your SOAP envelope exactly looks?
>
+
# Can I extract some ID value from the SOAP envelope and use it as the message ID?+
You can use the com.sap.aii.axis.soap.MessageIDExtrator handler to extract some ID value from the SOAP envelope and use it as the message ID. This handler can extract an ID string value (i.e., the 36-character GUID string) from the SOAP envelope and set it to the request or response message ID property in the message context. The ID string must be contained within some XML element. See a configuration for extracting the ID from WS-Addressing's MessageID element. {quote)
Hi,
Thanks for your reply;
I'm familiar with xpath however the FAQ does not mention the use of xpath anywhere. Please see above an extract of the FAQ regarding the MessageIDExtractor;
The provided example of the module configuration looks like this:
Module Key | Parameter Name | Parameter Value
id | handler.type | java.com.sap.aii.axis.soap.MessageIDExtractor
xireq | handler.type | java.com.sap.aii.axis.xi.XI30InboundHandler
sap | module.pivot | true
xires | handler.type | java.com.sap.aii.axis.xi.XI30InboundHandler
When you observe this configuration you notice that there's only one entry for the MessageIDExtractor. How will the handler know which XML field to pick from the incoming SOAP envelope? I think the example is missing some additional parameters where you can provide the xpath query.
Can you clarify?
Many thanks,
Roberto
Edited by: Roberto Viana on Nov 5, 2010 9:00 AM
Edited by: Roberto Viana on Nov 5, 2010 9:06 AM

For showing smartform through dynpro is ther any ADS configuration needs ?

Hi,
I want to show Smartform with dynpro application. I tried it on development server it have worked fine. But same application i tired on quality server but it did not work . So i want to know is there any ADS Configuration needs for that or i have to apply some note for that.
Help will be rewarded.
Regards,
Gurprit Bhatia

Thanks Arafat and Amit for quick answer,
I am working one application in which i am showing smartform through dynpro. In development this application shows Smartform as PDF but When i try same application on Quality or Production . It does not show anything means pdf does not generated.Is there any note for that.
Regards,
Gurprit Bhatia

For showing smartforms through dynpro,Is there any ADS Configuration need ?

Hi,
I am showing smartform through dynpro application . So Is there any adobe document service configuration need for same.Please provide details if possible.
Regards,
Gurprit Bhatia

Thanks Arafat and Amit for quick answer,
I am working one application in which i am showing smartform through dynpro. In development this application shows Smartform as PDF but When i try same application on Quality or Production . It does not show anything means pdf does not generated.Is there any note for that.
Regards,
Gurprit Bhatia

Analog Lines to E1 DID/DOD configuration need for CCME

Similar Messages

Maybe you are looking for