Anlysing saved data in labview signal express

I need to collect data and later analysed them in labview signal express. I could do as i get thee data but saving the project and doing the analysis later is not working using the add step function.
What should I do ?
Secondly how do you convert to ascii and export to excel or word when using signal express ?
Regards
Matthew

Hi mathade,
I am not sure what exactly are you trying to do. Are you taking some signals from signal express and then saving them and later reading the saved values for analysis? If this is what you want to do, you can simple write your values into a spreadsheet and later on read it from there using the File I/O functions for doing the further analysis. If you want to do it in the same execution run, you can also hold the values in some shift registers and get the analysis done after the acquisition. 
I can give you more information if you can post your vi so that I can take a look at your progress so far.
Regards,
Nitzz
(Kudos are always Welcome) 

Similar Messages

  • Event Acquisition in LabView Signal Express

    I have the USB-6009 data logger and LabView Express. I am trying to record certain events as they happen in the process. The signal I am recording is a 0 or 10 V DC signal and each time that signal goes to 10V DC I want to record that as a event. I am not worried about the actual voltage just the event. I am not sure what the best way would be to set this up in LabView signal express. Any advice on how to achieve this.

    Hi CoryB,
    In SignalExpress you can create events by in the Recording Options tab clicking Events. Then, in the Category list select Add. From here, you can change the options for the event. Here is a link to the help on the events page.
    Also, Dennis is absolutely correct. You will get better assistance with your questions if you post in the correct board.
    Bill E. | Applications Engineer | National Instruments

  • Labview Signal Express and Matlab

    Hello,
    I am using Labview Signal Express to acquire and log data from an injection moulding machine (with NI USB-6218).
    The logs contain more than 65000 samples so my boss told me to treat the data with Matlab.
    Can anyone tell me how to do that? (I think that I have to export these data in a text file before but how???)
    Thank you very much for your help
    Regards.
    Helene

    Hi there, I’m currently studying mechatronics in Sligo institute of Technology in Ireland and we have to do a SCADA project using LabVIEW to control an injection moulding process. I work in the Water and waste water treatment area so I’ve no experience of Injection Moulding. I found your address on the web and was wondering would you have any screen shots of what an injection moulding SCADA interface would look like or a schematic/P&ID  of an injection moulding process. Any help would be greatly appreciated. Regards Richard Crowe

  • Why the acquisition with DAQmx is different by using Labview 8.2 from Labview signal express?

    Hello,
    I am using a PCi-6281 to acquire a voltage. When I am using Labview signal express with only the step to acquire I read the good signal with the exact voltage. But when I am using my VI, the y axis and the values recorded are wrong. Why this difference appears?
    I insert a picture with both signal: at the top is the signal from my vi (wrong measurement) and at the bottom is the signal from labview signal express (correct).
    The vi I am using is the example Cont Acqu&Graph Voltage-To file (binary).vi.
    Thank you for your answer!
    Sophie
    Sophie

    I am using the binary file because it requires the minimum change in another VI. I have tried to change in scaled data but now my second VI has not enough memory to display all data.... What's wrong? Here is my second VI. Totest with data you need to insert a number in the "scaling factor" if not the dat are multiplied by zero...
    thanks for your help!
    Message Edité par stage84 le 07-24-2009 10:11 AM
    Attachments:
    Display 3.vi ‏1867 KB

  • Adding offset to LabView Signal Express signals

    We are using a USB 6535 with LabView Signal Express. 
    The logging need is to record 8 channels of data, with each having 3 unique (0->5V) signals. 
    So far, only the first channel has been wired in an the logging inputs set up.
    With a standard scope, there are offsets to offset a signal vertically, and to thus see the overall time relationship. 
    How is that done with LabView Signal Express? 
    Each channel's 3 signals need to be grouped together and then 8 channels vertically offset for visibility.
    Thanks

    Hello,
    The best way I can think of is to create a constant signal (or however many you'd need) and add or subtract to the signals you are acquiring.  In SignalExpress, there's an Arithmetic step that is helpful for this.  The following KnowledgeBase article from our website offesr one way to do this in SignalExpress:
    http://digital.ni.com/public.nsf/allkb/555B4791612​E261E8625763F0031DC2C?OpenDocument
    Best,
    Ryan C.
    Applications Engineer
    National Instruments

  • LEGO Mindstorms 2.0 crashes at startup when LabView Signal Express is installed first

    When NI Circuit Design Suite Education Edition is installed first in a computer and the LEGO Mindstorms software second, the LEGO Mindstorms software doesn't work, it reports the following:
    Error: A required file is broken
    Possible Solutions: Reinstall the LEGO Mindstorms NXT Driver  (tried but doesn't work)
    Error code: 1003
    Ordinal not found
    The ordinal 18 could not be located in the dynamic link library NIVISV32.dll
    Error loading "fantom.dll"
    The operating system can not run %1
    On other computers the LEGO software starts running, it displays part of the initial screen and then a small window opens saying that the Mindstorms software has has an error and that it will close. The previous report doesn't show.
    If LabView Signal Express is uninstalled and then the LEGO software reinstalled, the LEGO software works.
    I've dowloaded and installed new and old versions of the NIVISV32.dll and this doesn't correct the problem. I went as far as version 4.20 of the dll because it is dated in 2007 and the dll file installed by the LEGO software when it works is also dated 2007, but if I install the dll without uninstalling LabView Signal Express, the LEGO software continues not working.
    Please advice how to correct this problem without having to uninstall LabView Signal Express first. If the LEGO software is installed first, is LabView Signal Express going to use and not to replace the old 2007 version of the dll installed by the LEGO software? Is there any LEGO software update that corrects this problem?
    I repeat: I know a solution is to uninstall LabView Signal Express, install LEGO Mindstorms and then reinstall LabView Signal Express but I have 60 computers already cloned and deployed with this problem, so I don't want to go to this long process to fix the problem. The computers are using Windows 7 and problems happen on both the 32 and 64 bits versions of Windows 7.
    Any ideas???
    Solved!
    Go to Solution.

    I couldn't reproduce the error either, but in our x86 computers this problem appeared after several months; we used LEGO Mindstorms last time in Summer 2011 without any problems and just three weeks ago when we were checking the computer for our Summer 2012 classes if when we noticed the problem. I’m still going to try to reproduce the error in an x64 computer where the problem appeared immediately.
    Anyway, I’m attaching a word file with images of captured screens where you can see the error reports generated by LEGO Mindstorms and a series of steps uninstalling and reinstalling these program plus LabVIEW, until LEGO Mindstorms finally works after having uninstalled all traces of LabVIEW.
    Images can be expanded and zoomed in to a better view of the details and if I can reproduce the problem in an x64 computer I’ll let you know.
    Please see if you can find out something based on the images I’m sending.
    Thank you.
    Attachments:
    LEGO PROBLEM.doc ‏3129 KB

  • LabVIEW Signal Express, averages

    Hello,
    I'm brand new to LabVIEW. I have a temperature signal  from a thermocouple up in LabVIEW express, and I'm trying to get an average of this signal because it's very noisy. Can anyone provide me with very detailed help (as I'm brand new, and have no idea how to do anything in LabVIEW).
    If it's of any help, I have LabVIEW 8.5 and LabVIEW Signal Express 2.5.1. Thank you!

    Hello ddrop,
    To add to Intelligent's post, here is another example to show you how to create a running average of an array.  I am not sure how you have your measurements recorded (if you are creating an array), but this example should give you some added guidance.
    You mentioned you were using Signal Express and there are a set of Signal Express examples that may also be helpful.  You can find the examples by going to Help>>Open Example...  This should take you here: C:\Program Files\National Instruments\SignalExpress\Examples.  From there, you can go to Loops>>Frequency Sweep with Averaged Measurement.seproj. While this example does not do exactly what you are doing, it will at least give you an idea of how to do averaging in Signal Express.  Another way to incorporate the averaging in Signal Express would be to do a Run LabVIEW VI step.  I hope this helps!
    Kim W.
    Applications Engineer
    National Instruments

  • Ajout d'un affichage dans Labview Signal Express

    L'ajout d'un affichage (quand il ne s'agit pas d'un graphe par exemple ajout d'un affichage "Thermomètre") dans Labview Signal Express est impossible et conduit à la fermeture du logiciel, quelqu'un a-t-il une solution pour remédier à ce problème ?

    Bonjour yj55,
    Ce problème effectivement n'est pas normal.Avez-vous un message d'erreur qui s'affiche? Est-ce un problème que vous n'aviez pas du tout avant?
    Vous pouvez par exemple tenter de faire une réparation de Labview Signal Express
    Cordialement
    Mathieu B
    National Instruments France
    #adMrkt{text-align: center;font-size:11px; font-weight: bold;} #adMrkt a {text-decoration: none;} #adMrkt a:hover{font-size: 9px;} #adMrkt a span{display: none;} #adMrkt a:hover span{display: block;}
    Forum Aéronautique, Spatial et Défense. Avec la participation exceptionnelle de Bernard DUPRIEU, Res...

  • LabView Signal Express ECG

    HI, 
    Iam using LABVIEW SigNal Express to genErate a mouse ECG. 
    I hooked up tWo alligator clips to the mouse and connected them to a differential amplifier. The output goes through a USB-6008 NI DAQ board to my PC. I get a nice ECG graph on my PC, but now I would like to generate sound as well. 
    Any idea how I should do this with Labview Signal Express? 
    Thanks, 
    Charlotte

    You need to post to the SignalExpress board. LabVIEW is the language used to create SignalExpress and you won't find to many users of SignalExpress here.

  • Where can i find labview signal express DAQ assistant at?

    Hi, i need help
    Q1) where can i locate Labview signal express DAQ assistant at?
    Q2) Is Labview signal express functions same as Labview 8.6 ?

    LabVIEW Signal Express and LabVIEW are two different products.
    If you are talking about the DAQ Assistant, then you need to have the latest DAQmx driver installed and you should be able to find in the Measurement I/O palette on the LabVIEW Block Diagram.
    Adnan Zafar
    Certified LabVIEW Architect
    Coleman Technologies

  • Help! LabView signal express

    Hola!, tengo un pequeño problema y me gustaria que me ayudaran!, estoy realizando  un espirometro de turbina! y estoy generando una  onda cuadrada y la estoy viendo desde el labview signal express , esta onda cuandrada va de 0 a 5Volt, y necesito  contar la los pulsos y integrarlos para obtener el grafico adecuado! ..... si me pueden ayudar se los agradeceria!

    Hola,
    ¿Está utilizando SignalExpress Limited Edition o versión completa? Si utiliza la edición limitada que no puede utilizar las funciones matemáticas de análisis y procesamiento de señales.
    Are you using SignalExpress Limited Edition or Full Edition? If you use the limited edition you cannot use mathematical analysis functions and signal processing functions.
    Saludos,
    Abel Souza
    NI Brazil
    Abel Souza
    Engenheiro de Aplicações
    National Instruments Brasil

  • How can i generate AMI line codes in LabView signal express?

    i wish to conduct a project that uses AMI line codes. but i have a hard time using signal express to generate it. can anyone help me with that?

    Hello Barry,
    That is really a problem, in LabVIEW, we can only convert vi to the previous version, I have version 7.1 and so I can only convert to version 7.0 and you cannot open this too.
    But I think that it's very easy to do what I'm trying to explain you.
    Go to the cluster group in the functions pallete. Place an unbundle by name function in the diagram and connect it to the data that's comming out of the FFT Power spectrum vi - the pink (or watever) wire.
    Click in the white part of it (it should contain something like f0), choose magnitude.
    This is now an array that you can connect to the peak detector function.
    Take care about the threshold and width parameters of the peak detector.
    Take a look at your signal and decide the amplitude and width of the peaks you want to detect. The threshold is the amplitude above what you consider as a peak, the width is a little bit more complicated - to begin, 3 or 4 should be a good number if you signal is not too noisy - bigger widths will somehow do a kind of a low pass filtering to your signal.
    The position output of your peak detector is an array of locations where your peaks were found.
    Keep in mind you are now working in frequency domain and that position means something in the frequency domain.
    The array you placed as input of the peak detector is an array of points starting in f0 and separated by df (the other elements of the cluster).
    So to calculate the real value of the peaks, you have to multiply them by df and add them f0.
    Sorry by the big text and sorry if I went too much in detail,
    Hope it helps,
    Paulo

  • How to view signal in a waveform chart in Labview Signal Express?

    Hi,
    I would like to view a signal in Signal Express 3.0  in a "waveform chart" but don't know how to do it and I am thinking that it may be impossible?
    In Labview there are two ways of viewing data, either in a "waveform chart" or in a "waveform graph". The great thing with "waveform chart" is that it lets you define a history length and you can see the data move to the left (strip chart option) as the samples are being retrieved. It works perfect. 
    In Signal Express I can only select "XY graph" or "Waveform graph" by making a right-click the mouse but I cannot select "Waveform chart". Is it really true that it is not possible to view the data in a "waveform graph with Labview SE? (1 analog signal being read continuously, 100 samples to read at 1K rate)
    Thank you in advance,
    Enrique
    Solved!
    Go to Solution.

    Hi Enrique,
    You are correct that there is currently no waveform chart in SignalExpress. The closest thing you can get to, is recording the data as a log and then viewing it while recording (which I realize is not quite the same, interactive behavior).
    For your last comment, you wrote "waveform graph", but I assume you meant to say "chart" there as well.
    Sorry about this. We have recently been getting this request, so perhaps in a future version.
    Phil

  • Labview signal express to excel

    Hello,
    I'm using Labview signalexpress to acquire a signal. My problem is that I acquire 20 seconds of my signal (and I see it on the graph), but the problem is that I can export to excel the only 1.35 seconds, whatever the number of samples. How could I export to excel the entire signal?
    Thanks
    Solved!
    Go to Solution.

    I don't have signal express but a quick search found this link.  It states that there is a setable limit on the size fo data sent to the clipboard.  
    "When you export data to Microsoft Excel, LabVIEW SignalExpress copies data samples to a clipboard for export. Use theMaximum Clipboard Data Export Size option on the Data page of the Options dialog box to increase the number of data samples the clipboard can contain. Depending on the amount of memory on a machine, large log files might not export successfully."
    You might be running into that limitation when you try this method.  Even if you increase the limit you will still not be able to paste more than excel's max size as discussed already.  You would have to paste it into a text file or some other program that can handdle that much data.  I would not use this method however.  Seems like it would be to easy to make mistakes that way.
    A .lvm file is just a text file so you should not run into any limits there.  This is what I would use. 
    Lukin
    Certified LabVIEW Developer

  • NI Labview Signal Express activation dont work

    Actually, signal express was working properly. We tried to run the upgradation cd on 4 Jan, 2010 that was provided by NI in august 2009. It was taking unexpectedly longer time and we turminated running the setup before completion. When we start signal express a window appeares that ask for activation (see attachment). Even after activating properly, same window appears time and again. We are unable to start signal express, please do the needfull.
    Attachments:
    Activation window.doc ‏130 KB

    Hello,
    Sounds like aborting that installation may have corrupted your software. I would try to repair Signal Express with the original disks that you had and see if that works ok before trying to install the upgrade again. You can repair NI software by going to Add/Remove programs, find National Instruments Software and click Change/Remove. This brings up a window where you can select Signal Express and click the repair button. It will probably ask you for the CDs that you installed from ( the original CDs). Let us know how this goes, if you have problems or questions we will try to help.
    Thanks,
    National Instruments

Maybe you are looking for

  • How to transport standard text in SO10 to different system.

    Hi, I need to change the standard text in SO10. I need to change the custom text. We have a custom text id (zval) associated with it. How to transport the changes i have done from Dev to Quality to Production. I wanted one clarification: when we crea

  • When using imovie and converting to idvd the cd ejects before the burn is complete.  how can I burn the movie for viewing?

    when in idvd the disc ejects before multiplexing and burning are completed therefore the disc has issues when viewing.  there are damaged areas.  Is there a work around to burn the movie?

  • Budget problem for External processign Service

    Please note that , we have created a network for supply of Services from Vendor A and placed the PO for Rs.1,00,000/- Vendor has done the 45 % work and subsequently service entry sheets are posted for the same. But then Vendor expressed his inability

  • I need a new gfx card

    Hi I have an ati 5870 card and i use 3 screens with DVI ports incl 1 display port adapter for the third screen. And now i want a new gfx card but i dont know what to chose because i need to connect my 3 screens with DVI The card i am looking for must

  • ADF Table Refresh/Commit on Delete

    ADF 11g in jDeveloper 11.1.1.1.0 So, I have an ADF Table component in a panel collection. Within the collection, I added a menu with menu item to delete the current row. The delete row is not being committed. Is there a way to do a row delete in one