ANM 5.2 unable to import ACE 4710

Good day,
I am currently experiencing a problem while trying to import multiple 4710 ACE Appliances into ANM. ANM version is 5.2 and ACE 4710 Appliances version is 5.1.2. The error message is the same for all Appliances (currently 14, more to be deployed this year, another 12 this year). The management class, policy-map and servcie policy are all in place.
The error message is below:
Any assistance would be greatly appreiated.
Thank you.
Paul

Paul,
Can you get a show tech-support?
After that, can you do the following:
1. "dm status"
2. "dm reload"
3. "dm status"
I think you probably may require to reboot the box but it will be better to open a TAC case for that and check deeper.
Hope this helps!
Jorge

Similar Messages

  • Importing HA 2 ACE 4710 into ANM 4.1

    I am New to ACe Loadbalancers. We have just installed the ANM4.1 and we are trying to import both appliances into the ANM4.1. Is there somthing I sould be aware off before I do the Install.? The question is when O do the Import does the ANM will have my config from the aces AS IS untouched. I am making sure that the ANM will not delete my config on the ACES
    Thanks

    Hi Hussaini,
    As per best practice I would like you to make sure that you have taken the backup of all the context of ACE using running config and saved it separately other then the device itself so at any point of contingency your hard work for configuring the box should not go in vain and you be ready for any kind of situation post import into ANM.
    When you install ANM for the first time you need to add a license from the command line before you can access ANM.
    ANM requires licenses to manage virtual devices and to run the ANM server or servers.
    ANM checks against the licensed Virtual Context count on each ACE.
    Thus if you have the ACE-VIRT-020 license on the ACE, to manage that ACE you must have an available ANM-AV-020 installed on the managing ANM. Even if that ACE to be managed has 5 or fewer defined Virtual Context or so.
    BTW..if at *any* time you get stuck in an operational bind due to ANM licensing, go to www.cisco.com/go/licensing, select the first link for evaluation licenses, and from there select to get evaluation license PAK for ANM. This will allow you to install the evaluation license that is *unlimited* for 90 days. Hopefully that is plenty of time to order the additional licensing you need for production operations.
    For each ACE with ACE-VIRT-020 ANM needs qty 1 of ANM-AV-020.
    Same for 050, 100, 250.
    ANM uses the following protocols for communication:
    For communication to an ACE module or appliance:
    –XML over HTTPS
    –SSHv2 (read and write)
    –SNMP V2C (read-only)
    –Syslog over User Datagram Protocol (UDP) (inbound notifications only)
    Enabling SSH Access and the HTTPS Interface on the ACE Module and Appliance
    http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/application_networking_manager/4.1/user/guide/UG_manage_devices.html#wp1362821If the ACE module or appliance is new and still has its factory settings, you do not need to perform the procedure in this section because SSH is enabled by default.
    If you are using ANM with an ACE module or ACE appliance and you configure a named object at the ACE CLI, keep in mind that ANM does not support all of the special characters that the ACE CLI allows you to use when configuring a named object. If you use special characters that ANM does not support, you may not be able to import or manage the ACE using ANM.
    The quickest and easiest way to add devices to ANM is to import them individually using the Add function available at Config > Devices. If you already know the device IP address, you can use this procedure to add your devices to ANM.
    Before you begin importing, you need to set up your network devices so that ANM can communicate and monitor them.
    Before importing a device, the ANM server pings the IP address of the device. If you have a firewall between the ANM server and the device that you want to import, your network administrator needs to modify the firewall to allow the ping traffic to reach the device or ACE.
    http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/application_networking_manager/4.1/user/guide/UG_manage_devices.html#wp1449529
    You can install the ANM server software on a standalone server or on a VMware virtual machine . The capabilities and functions of the ANM software are the same regardless of which application you use. The two ANM applications:
    ANM server: Dedicated server with ANM server software and Red Hat Enterprise Linux (RHEL) operating system installed on it. For information about installing this type of ANM application, see the Installation Guide for the Cisco Application Networking Manager 4.1.
    ANM Virtual Appliance: VMware virtual appliance with ANM server software and Cisco Application Delivery Engine Operating System (ADE OS) installed on it. Cisco distributes ANM Virtual Appliance in Open Virtual Appliance (.OVA) format. For information about installing this type of ANM application, see the Installation Guide for the Cisco Application Networking Manager 4.1 Virtual Appliance.
    So I am repeating again that please check the liscense as the ANM_AV license needed as it doesn't depend on the amount of contexts currently in use.
    If the ACE you are trying to import is using more contexts than the amount allowed by the ANM_AV license then you can face problem during import or only that much contexts will be imported and rest will fail to sync or face problem during import.
    You can check this value with the "ACE# show license status" command.
    Some times there may be chance for license mismatch between the ACE and the ANM.
    ANM uses TCP port 10444 for the ANM License Manager.
    For any other difficulty if you face even after this please write back to me.
    HTH
    Sachin Garg

  • ACE 4710. Unable to clear ssh sessions

    Hi.
    Once in the CLI of an ACE 4710, using the command "clear ssh session id" I am unable to clear/kill any of the remote ssh sessions established.
    According to the administration guide, the "clear ssh .." command must clear the sessions, but it does not, or maybe I am missing something?
    http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/ace_appliances/vA1_7_/configuration/administration/guide/access.html#wp1050335
    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Tabla normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-priority:99;
    mso-style-qformat:yes;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:11.0pt;
    font-family:"Calibri","sans-serif";
    mso-ascii-font-family:Calibri;
    mso-ascii-theme-font:minor-latin;
    mso-fareast-font-family:"Times New Roman";
    mso-fareast-theme-font:minor-fareast;
    mso-hansi-font-family:Calibri;
    mso-hansi-theme-font:minor-latin;}
    ACE/CONTEXTO_A# show ssh session-info
    Session ID     Remote Host         Active Time
    13728          222.98.54.158:50556   67:43:38
    13732          200.44.158.70:46172   67:43:36
    13735          200.44.158.70:46174   67:43:36
    13737          200.44.158.70:46177   67:43:36
    ACE/CONTEXTO_A#
    ACE/CONTEXTO_A# clear ssh 13728
    ACE/CONTEXTO_A# clear ssh 13732
    ACE/CONTEXTO_A# clear ssh 13735
    ACE/CONTEXTO_A# clear ssh 13737
    ACE/CONTEXTO_A# show ssh session-info
    Session ID     Remote Host         Active Time
    13728          222.98.54.158:50556   67:43:54
    13732          200.44.158.70:46172   67:43:52
    13735          200.44.158.70:46174   67:43:52
    13737          200.44.158.70:46177   67:43:52

    Hello,
    Seems to be working for me in my tests.  Works in the Admin context and a user context, and when clearing connections from console connection or one of the SSH sessions.
    ace-appliance-15/CTX1# sho ssh sess
    Session ID     Remote Host         Active Time
    24705          161.44.77.245:1586     0: 1:42
    25100          161.44.77.245:1589     0: 0:27
    25116          161.44.77.245:1590     0: 0:16
    ace-appliance-15/CTX1# clear ssh 25116
    ace-appliance-15/CTX1#
    ace-appliance-15/CTX1# sho ssh sess
    Session ID     Remote Host         Active Time
    24705          161.44.77.245:1586     0: 2: 5
    25100          161.44.77.245:1589     0: 0:50
    What version of software are you running on your 4710?  I am running the latest A3(2.4).  Can you try this version?
    Thanks,
    Sean

  • Can not import ACE module to ANM

    Hello,
    Good day.
    I recently facing an interesting problem.
    We are running ANM 5.1.0 to manage our LB contexts, those contexts are configured on ACE20-MOD-K9 module which installed in Catalyst6500 switch. Our installation is like this, two ACE20-MOD-K9 modules installed into same Catalyst6513 different slots. And  those two ACE modules serves different Data Halls, contexts configured on those modules are completely seperated, different VLAN, different subnet no relation at all.
    I'm able to import the catalyst chassis into ANM and under Config>Guided Setup>Import Device>Modules, I'm able to see both ACE modules but only one module able to be imported, another one I can not even choose it. There are slightly difference those two modules show themselves in that page. The one I'm able to import shows exactly it's module type and version number but another one is showing someting strange.
    Slot#      Model                     Type            Serial #      State                 Version                Description                                      #VC
    3            ACE20-MOD-K9      ACE v2.3      XXXXXX      up                     A2(3.5)                Application Control Engine Module      28
    9            ACE20-MOD-K9      Module         XXXXXX      Not Imported      ace2t_main_d      Application Control Engine Module      N/A  <---problem module
    Does any was facing samiliar problem?
    Thanks

    I think I found something related to my issue.
    In ANM operating Guidance,section"Importing ACE Modules after the Host Chassis has been Imported" mentioned some restriction. The module in slot 9 actually has samiliar situation, show module commands shows that Catalyst chassis doesn't really recognize the software version that might caused ANM not able to figure out if that module is supported or not so it makes a simple decision deny import. I will try to reboot that module see if we can fix this issue.
    "Guidelines and Restrictions
    ANM 3.0 and greater releases do not support the importing of an ACE module that contains an A1(6.x) software release or an ACE appliance that contains an A1(7.x) or A1(8.x) software release. If you attempt to import an ACE that supports one of these releases, ANM displays a message to instruct you that it failed to import the unrecognized ACE configuration and that device discovery failed.
    However, if you perform an ANM upgrade (for example, from ANM 2.2 to ANM 3.0), and the earlier ANM release contained an inventory with an ACE module that supported the A1(6x) software release or an ACE appliance that supported the A1(7.x) or A1(8.x) software release, ANM 3.0 (and greater) allows the A1(x) software release to reside in the ANM database and will support operations for the release. ANM prevents a new import of an ACE module or ACE appliance that contains the unsupported software version.
    We strongly recommend that you upgrade your ACE module or ACE appliance to a supported ACE software release, and that you instruct ANM to recognize the updated release. See the "Instructing ANM to Recognize an ACE Module Software Upgrade" section.
    See the Supported Device Tables for the Cisco Application Networking Manager for a complete list of supported ACE module and ACE appliance software releases."
    http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/application_networking_manager/5.2/user/guide/UG_manage_devices.html

  • ACE 4710 HTTPS load balance configuration

    Have two ACE 4710 in HA setup. We would like to setup HTTPS loadbalance(actually just a primary and standby configuration in the serverfarm). Initially this would be for Exchange OWA connections but may expand to more HTTPS connections later.
    I know there are several ways to do SSL with the ACE( client, server, end-to-end). I am just wanting to know the easiest way to deploy this? Is a certificate always needed on the ACE for each connection? In HA mode would a certificate be needed for both or does it replicate in some way to the other ACE?
    Any configuration examples would be helpful.
    Thanks.

    IF you terminate SSL on the ACE you need certificates and key on ace in the context in which you are doing the termination. The certs and keys need to be installed on the active and standby (manually unless using anm to manage).
    when speaking of SSL
    SSL termination refers to ace terminating SSL and sending to server as clear text
    end to end - ACE terminates SSL (to look into payload to make a loadbalance decision or sticky decision) and then re-encrypts to the server, so to the client ACE is an ssl server and to the server the ace is an ssl client.
    You can find some config examples at
    http://docwiki.cisco.com/wiki/Category:Data_Center_Application_Services_Configuration_Examples

  • ACE 4710 Appliance: init: failed to initialize modlock_init(): No such file or directo

    Hi,
    I have ACE 4710 Appliance, but it is failed and giving following error while login at console.....
    I am suspecting hardware issue..most probably with harddrive.... Please let me know if it can be recoverable of only replacement is the solution..
    switch login: init: failed to initialize modlock_init(): No such file or directo                                                                             ry
    eth2: ERROR while getting interface flags: No such device
    perform_sysmgr_offline: unable to move MTS to MTS_STATE_OFFLINE: Invalid argumen                                                                             t (error-id 0x801E0016).
    init: failed to initialize modlock_init(): No such file or directory
    eth2: ERROR while getting interface flags: No such device
    perform_sysmgr_offline: unable to move MTS to MTS_STATE_OFFLINE: Invalid argumen                                                                             t (error-id 0x801E0016).
    init: failed to initialize modlock_init(): No such file or directory
    eth2: ERROR while getting interface flags: No such device
    perform_sysmgr_offline: unable to move MTS to MTS_STATE_OFFLINE: Invalid argumen                                                                             t (error-id 0x801E0016).
    /isan/sbin/sysmgr: symbol lookup error: /isan/lib/libutils.so: undefined symbol:                                                                              tftp_callback_fn
    Regards
    Nadeem

    Hi,
    I RMAed the appliace, i think it was hardware failure which casue this issue.
    If some one face this issue please let me know...Thanks!
    Regards
    Nad

  • ACE 4710 - DM initialization failed

    When trying to get to the device manager GUI on my ACE 4710 I get to the login screen. On entering credentials I am given an error
    "DM initialization failed (Failed to import ACE configuration: Device discovery failed: unknown). Contact your technical support team."
    I have tried "dm reload" but I am still getting the error.
    Any help greatfully appreciated.

    You are probably hitting CSCsv95366. This is fixed in A3(2.2).
    You can get the details about this bug at
    http://tools.cisco.com/Support/BugToolKit/action.do?hdnAction=searchBugs
    HTH
    Syed Iftekhar Ahmed

  • ACE 4710 dramatically increasing Sticky entries

    Hello,
    When I do a "show resource usage" on my ACE 4710 / SW  Version A3(2.5) I see the Sticky entries increasing peramanently.
           Resource         Current       Peak        Min        Max       Denied
    sticky                    50758      62348      65536          0          0
    When I have a look to the ANM managing the box I see the last days the current value was round about 25000 / 27000 max.
    I look for a method to discover by what sticky definition or by what function / realserver the most increasing counters / entries are caused.
    When I use the sh sticky database .... I see the lists for group or a special realserver / client but I miss sh show top clients / rservers / rules what generates the big sticky table....
    Any good tipp how to troubleshoot that will be appreciated.
    Regards
    Gerhard

    Hello Surya,
    Thank you for your response. I us a mix of different persistance Methods:
    For some of the services  source-ip based, for other, Cookie-based, and for some other I look on a special http header field... So it would be interesting to find out for what of the methods  ths sticky entries grows...Because I see the counter rising  since 2nd Oct 2:00 am... before it was never so high...
    Regards
    Gerhard

  • SSL Certificates Update Error in ACE 4710

    Hi,
    I am facing a problem while updating the SSL certificates in ACE 4710. Our certificate is expired and we have purchased a new certificate from CA. Moreover the common name of the certificate is also changed.
    I tried importing the certificate to the repository and change the SSL proxy likewise to use the new certificate. but still the new certificate with new CN is not recognised by the clients. they can see the old certificate only. I even tried deleting and creating a new ssl proxy service with the new cert and attaching it to policy map.
    but still the new certificate is not used even after a reboot,
    Attaching screenshots and running config. Any help will be appreciated.
    BR//Rajiv

    Ravi,
          Here are the procedures for updating your certificate on the ACE. 
    1) Create New RSA Key
    2) Create CSR
    3) Send CSR to CA authority for a new certificate
    4) Import Certificate into the ACE
    5) Change the ssl-proxy to use the new Certificate and Key
    6) Remove the SSL-Proxy from the policy map and reapply
    Now if you created the CSR on a different box, you will need to import both the RSA key are the certificate.  Another thing you should be aware of is a possible change in the Root and intermediate certicates that are used by the CA.  In your configuration, you have
    crypto chaingroup iotms-chain-gr-1
      cert inter-root-new
    Is the the correct certificates for your cert?  If so, it seems odd that there is only on certificate in the Chaingroup.  Most CAs use an intermediate and and a root certificate. 
    Verify that you have the correct chaingroup (with the correct root and intermediate certificates). 

  • ACE 4710 in failover - ssl offload, cert for second ACE

    Hi,
    I'm testing two ACE 4710 appliances that should work in active/standby mode and do ssl offload in bridged mode.
    At the moment I have configured one of the devices to do basic load balancing (without ssl offload).
    Now I would like to move further and configure ssl offload and configure High availability.
    I read that the certificate for ssl can be localy generated on the ACE device but I couldn't find any information regarding the cert that should be used on the second ACE.
    Should I generate a new cert od the standby unit or somehow use the one on the first ACE?
    Is it better to first set up high availability and then configure ssl offload or vice versa?
    Does anyone have a config example of ssl offload and active/standby configuration?
    Thank you in advance.

    You simply need to generate keys & CSR on the primary ACE. Export the Keys from Primary ACE, Import these keys to Standby ACE and once you recieve the certs from CA then simply import the cert to both ACEs.
    FOllowing will be steps to achive that
    On primary Ace
    1. create RSA Keys
    crypto generate key 2048 app1.key
    2. Create CSR & send it to CA
    ace/Admin(config)# crypto csr-params app1-csr
    ace/Admin(config-csr-params)# common-name www.app1.com
    ace/Admin(config-csr-params)# country US
    ace/Admin(config-csr-params)# email [email protected]
    ace/Admin(config-csr-params)# locality xyz
    ace/Admin(config-csr-params)# organization-name xyz
    ace/Admin(config-csr-params)# organization-unit xyz
    ace/Admin(config-csr-params)# state CA
    ace/Admin(config-csr-params)# serial-number 1234
    ace/Admin(config-csr-params)# end
    ace/Admin(config)# crypto generate csr app1-csr app1.key
    (copy the result to a file)
    4. Import certificate recieved from CA
    crypto import terminal app1.cert
    (pasted the content from the cert)
    5. verify the cert & keys match
    crypto verify app1.key app1.cert
    6. Export the keys from Active
    crypto export app1.key
    (copy the result to a file)
    ON Standby ACE:
    1. Import the keys
    crypto import terminal app1.key
    2. Import the cert
    crypto import terminal app1.cert
    3.verify the cert & keys match
    crypto verify app1.key app1.cert
    Hope this helps
    Syed

  • ACE 4710 Can not confirm http cookie sticky connections

    We are using a ACE 4710 with A3(2.6) software release.
    I had to change our sticky load balancing method for HTTPS to cookie based.
    However while connections appear to work if I look at the sho sticky database table I can not see or confirm sticky entries for the cookie based connections.
    Here or config snippets to show the config
    sticky http-cookie ghh-www scook-ghh
      cookie insert browser-expire
      serverfarm ghh-www-443
    class-map match-all ghh-www-443_CLASS
      2 match virtual-address 172.16.1.21 tcp eq https
    class-map type http loadbalance match-any ghh-www-443_CLASSURL
      2 match http url [.]*
    policy-map type loadbalance first-match ghh-sticky-443_POLICY
      class class-default
        sticky-serverfarm scook-ghh
    policy-map multi-match POLICY
    class ghh-www-443_CLASS
          loadbalance vip inservice
          loadbalance policy ghh-sticky-443_POLICY
          loadbalance vip icmp-reply active
          appl-parameter http advanced-options CASE_PARAM

    Another point: please check whether your servers are listening only for HTTPS traffic or also for HTTP traffic:
    in the first case the ACE will have to: decrypt the traffic from the client, inspect the http header to take the loadbalance decision and then re-encrypt it and send it to the server
    in the second case the ACE would have to: decrypt the traffic from the client, inspect the http header to take the loadbalance decision and send it out as it is unencrypted to the server
    the second solution would have the benefit of being easier to configure and to require less resoucerces both on the ACE (only decryption to be performed) and on the servers (no need for SSL operations at all there) but it might be that your company or business sector have requirements for which this traffic should never flow unencrypted, in which case you would have to go for the first solution.
    Here you have a config example for the first solution:
    http://www.cisco.com/en/US/products/hw/modules/ps2706/products_configuration_example09186a00809c6f37.shtml
    I would not expect you to have to pay extra for importing the cert and kepair into the ace, it would be just a copy, however as Alex said that may still depend on the license agreement with the CA.
    Cheers,
    Francesco

  • ACE 4710 FT failover failure

    Hello,
    I am running redundant ACE 4710 appliances running A3(2.7).  I have five FT groups configured along with FT Tracking and when the vlans fail due to physical links being down, the contexts to do not failover.  If one of the ACE boxes fail completely, failover works fine.  I have included the FT config from one of the contexts below.  I have a case open with TAC and the Engineer is suggesting the use of a query interface in additon to FT Tracking.  We have had two incidents on separate contexts where we lost a physical interface on the primary ACE, one for the maintenance of the core switch, the other was a cable disconnect and we are unable to understand why the indivdual context didn't failover.  Any ideas would be much appreciated.  Let me know if more info/configs are needed.
    Dave
    ft interface vlan 900
      ip address 10.10.10.1 255.255.255.0
      peer ip address 10.10.10.2 255.255.255.0
      no shutdown
    ft peer 1
      heartbeat interval 300
      heartbeat count 20
      ft-interface vlan 900
    ft group 3
      peer 1
      no preempt
      priority 210
      peer priority 120
      associate-context XYZ
      inservice
    FT Group                     : 3
    No. of Contexts             : 1
    Context Name                 : XYZ
    Context Id                   : 2
    Configured Status           : in-service
    Maintenance mode             : MAINT_MODE_OFF
    My State                   : FSM_FT_STATE_ACTIVE
    My Config Priority           : 210
    My Net Priority             : 210
    My Preempt                   : Disabled
    Peer State                   : FSM_FT_STATE_STANDBY_HOT
    Peer Config Priority         : 120
    Peer Net Priority           : 120
    Peer Preempt                 : Disabled
    Peer Id                     : 1
    Last State Change time       : Wed Jan 11 13:14:16 2012
    Running cfg sync enabled     : Enabled
    Running cfg sync status     : Running configuration sync has completed
    Startup cfg sync enabled     : Enabled
    Startup cfg sync status     : Startup configuration sync has completed
    Bulk sync done for ARP: 0
    Bulk sync done for LB: 0
    Bulk sync done for ICM: 0
    show int
    vlan424 is up, VLAN up on the physical port
    Hardware type is VLAN
    MAC address is 00:1e:68:1e:ba:b7
    Virtual MAC address is 00:0b:fc:fe:1b:03
    Mode : routed
    IP address is 10.104.224.6 netmask is 255.255.255.0
    FT status is active
    Description:"New Server VIP and real"
    MTU: 1500 bytes
    Last cleared: never
    Last Changed: Sun Mar 11 01:13:12 2012
    No of transitions: 3
    Alias IP address is 10.104.224.5 netmask is 255.255.255.0
    Peer IP address is 10.104.224.7 Peer IP netmask is 255.255.255.0
    Assigned on the physical port, up on the physical port
    Previous State: Sun Mar 11 00:04:57 2012, VLAN not up on the physical port
    Previous State: Sun Sep 18 10:21:15 2011, administratively up
         3991888419 unicast packets input, 23734607976687 bytes
         20246934 multicast, 174801 broadcast
         0 input errors, 0 unknown, 0 ignored, 0 unicast RPF drops
         1609345958 unicast packets output, 23690663385228 bytes
         7 multicast, 55807 broadcast
         0 output errors, 0 ignored

    Dave,
    For tracking to work you need to have preempt enabled. Can you try enabling preempt under the ft group and test your tracking again? Another potential issue you may run into is if your tracking is not lowering the priority enough when it fails. The difference between the active and standby device is 100. If you are not decrementing the priority greater than this value even if priority is enabled it will not lower it enough to force the failover. If after enabling preempt on this group the tracking still does not work as expected send you whole config for us to look at.
    Regarding the query interface; This is not a bad idea. It will help prevent an active active situation if there is a problem with the ft link between the two modules.
    Thanks
    Jim

  • ANM 2.0: one of three ACE contexts couldn't "sync to CLI"

    Hello,
    We are using ANM 2.0 Update A to manage an ACE module running A2(1.2). About a week ago, one of our 3 contexts started showing "Out of sync" in the "CLI sync status" column. I tried to sync the context numerous times; no errors were reported but this particular context was always "out of sync".
    Then this morning I tried a "sync to CLI" operation once more and this time it finally worked! The status is now "in sync".
    I was wondering why this happened, and if anything can be done to prevent it in the future.
    Regards,
    Marc.

    Synchronizing configuration files for the standby ACE requires:
    1. Auditing the standby ACE to confirm that its configuration does not agree with the ANM-maintained configuration data for the ACE. See Synchronizing Virtual Context Configurations, page 3-64.
    2. Uploading the configuration from the standby ACE to the ANM server. See Synchronizing Virtual Context Configurations in the below URL:
    http://www.cisco.com/en/US/docs/net_mgmt/application_networking_manager/1.2/user/guide/UG_virtual_contexts.html#wpxref74705
    3. For an Admin context, uploading configurations on any newly imported user contexts. If new user contexts are not updated, they cannot be managed using ANM.

  • I am unable to import pictures from my iphone to my computer.  Can anyone help?

    I am unable to import pics. 

    It sounds like you are using an application to import. You can do it manually.
    Start > Computer (on the right) > scroll to the bottom and you will see your iPhone under Portable Devices > Open it and you will see a Drive, open that and there will be a DCIM folder. That is where your photos will be (There may be other folders each holding photos).

  • Unable to import video frompanasonic VDR-D105 DVD video camera to imovie HD

    Trying to import my video from my dvd camera but imovie can not find camera. When I connect the firewire the camera locates DVD player software and allows me to play it on my computer, but not able to import to imovie. DVD Player allows my to clip my video but does not allow me to transfer of save it on my computer.
    If I'm unable to import, Is there a work around to get my video in imovie, say quicktime?
    I am using imovie HD 6.0.3.

    Hi S
    1. DVD-Cameras are for playback - not to be edited from.
    iMovie, FinalCut Express and Pro works with miniDV tape Cameras
    This course DVD and hard disk Cameras compact info to medium BUT in
    a destructive way. You can't get full quality back to be edited.
    miniDV also compacts to tape BUT Non-destructive = full quality to Mac.
    2. Does Your Camera really have FireWire. Most probably You are using
    the USB-cable that was delivered with Your Camera. FW is buy extra.
    Best solution - though sour. Change Camera
    If this isn't an option You'll have to back convert to streaming DV that iMovie
    and FCE/P understands.
    - Converting programs like may be:
    MPEG Streamclip converts from mpeg-1 to whatever you like (within reason).
    QuickTime MPEG-2 Playback Component
    or
    via analog out on Camera via an A/D-box to FW to Mac.
    Non is a good way though.
    Yours Bengt W

Maybe you are looking for

  • How to save the session states for a tabular form WITHOUT using check boxs?

    Greeting guys, As you know that we can use collections to save the session states of a tabular forms, described in the how-to doc of manual tabular forms. However, what I am trying to do ( or have to do) is to provide a manual tabular form, and save

  • May be the stupidest question, but anyway - where do I put my libraries?

    So, I download the Java Activation Framework, MAIL api, beanshell, etc. I get a nifty directory with not only the JAR but the javadocs etc. Where do people put these things on MAC OsX? I'm sure there's a best practice based on standards for where thi

  • Safety spot file for South Africa

    Hello. Please could someone tell me if there is a safety spot file for south african oiv maps. Im trying to load the file, but cant seem to find it anywhere. I have a nokia 5230, and I have updated my maps, but the folder is empty. Any help would be

  • Network bridge problems linking wwan0 and eth0 [SOLVED]

    Hi There, I have just got working a 3G modem which appears as device wwan0. I am trying to link this interface to my wired ethernet eth0. wwan0 seems to work fine with network manager, getting a IP address via dhcp works just fine and I can use the i

  • Command line Problems

    Hello!! I have problems with the find command. When I find something, a little time later my computer restarts. Only occurs with this command Somebody knows why occur this?? What I had to configure?