Another "dead" 4th gen

i'm sure this is not the first or the last, but i was not able to solve it
my case:
on ebay i got 2 ipods
one was only missing the home buttons and the screen was replaced but not glued in place allowing the buttom to be replaced first
the other has both screen and screws etc missing so i but that one to a side
the first one i just checked for the most obvious stuff like losse bits etc and then i got hold of a sync cable and let it charge for like 15 mins and it came to live, itunes could see it and offered me the latest update and that i did. i then let it charge some more to about 50% and started to have play with setting it up and put a few app's on it.
i checked that all hardware vise was working, wifi worked after resetting network settings, screen worked, speaker did and home button did as i could use my little finger to push the small one on the flexible board, what i did not check was the vol buttons and the top right hold button
i then left it for an hour or so and it had of course gone to sleep mode.
now the problem is that it will not charge or turn on.
i tried to hold the home key down for about 10 sec.... hold the home and hold for 30 secs, and holding home while pluging the sync cable... nothing happens

lllaass wrote:
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
as stated in my post i tried that
lllaass wrote:
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup
- Restore to factory settings/new iOS device.
can't be done since the device will not power on
lllaass wrote:
However, you may have a hardware problem
I think you are right... and then again... how can the device power on and work for a few hours and then go to sleep only to not wake up and not charge or power on?

Similar Messages

  • Dead ipod 4th gen

    I have a ipod classic 4th gen with 20gb and it has stopped working. I reset it when I first got it and put my songs on it and it worked fine. I let is set for a few months while I tried to find a new ipod cable for my car. When I tried to use it, with ear buds, it didn't turn on so I thought it may be dead even though it had a full battery when I shelved it. It has been plugged into a wall charger for about 45 minutes now and it still doesn't work. I have looked at a few other discussions and
    1 menu + select doesn't work, ipod is completely dead (fancy paper weight)
    2 my macbook 10.6.8  with itunes 10.6.1 doesn't to recognise my ipod, it doesn't even show up as being plugged in
    I get no exclamation points or sad faces just the black and white screen, off. It absolutely will not turn on.  I have yet to try the drop on floor method, especial since that is how I lost my last Ipod(poor ipod mini, I miss you). I also am not as technically inclined as some so I will also not be taking my ipod apart. I have aslo not dropped this ipod since I have owned it, looks like it was dropped maybe once before I got it.
    I really don't want to drive 45 miles to the nearest offical Apple store...
    Thanks for any help.

    Mine is dead too. I have 80GB Clasic. A few weeks ago, the LCD screen stopped working, and when i went into settings..with the help of a flashlight, the backlight in settings had nothing next to it like the other featueres had. Then I plugged into the computer and I barely saw LOW BATTERY.
    So I left it in thinking that is charging, but after several hours, it just had a blanl black window. I jiggled the power switch back and fouth and left it on OFF. I first tried to reset using the Center and Menu button, and held it for 6-15 secs...NADA, Then I did the same jiggling, and this time I tried the bottom Pause and center button (as a genius at apple phone support told me to try, and it worked. This was after I went to the genius apple store, three years ago, he told me it was FRIED.  I was ****** after spending 400.00 on this 80GB.
    Now.Nothing at all. Just Black screen. BUT, weirdly enough,afrter thinking the LCD screen went black and no useful, I did see the light on the LCD screen splashed a Apple website...WHAT?  How did that happen?  I tried differnt apple cables, JBL soundstage, my computer, and itunes, it also never showed up in devices.
    I'll think twice before i ever get another apple ANYTHING.  made in china.....well well well. Does not surprise me AT ALL!  So I guess this goes to recycle.  heck if i'm going to give this back to apple and get a smaller reburbished ipod, only to that to go out too. I'd rather toss it in the trash.

  • I have an iPod touch 4th gen that is in iOS 6.1 it's showing another update in the settings for iOS 6.1.6 but even if I wait for more than 30mins it won't show. Can anyone help me. Thank you and Godbless

    I have an iPod touch 4th gen that is in iOS 6.1 it's showing another update in the settings for iOS 6.1.6 but even if I wait for more than 30mins it won't show. Can anyone help me. Thank you and Godbless

    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on your router
    .- Reset network settings: Settings>General>Reset>Reset Network Settings
    - Try when connected to another network
    - Update via iTunes on a computer.

  • My 4th gen nano has locked up and the click wheel doesn't function, is it dead?

    Hi my 4th gen nano stopped working, the screens ok with no error messages but the click wheel no longer functions other than reseting. I've set it back to default ok but still no good as it's stuck on the language page. Is it dead??
    Pete.

    Hi jim,
    If you are having issues resetting your iPod Nano, you may find the following article helpful (it should be listed under iPods with click wheels):
    Apple Support: How to reset iPod
    http://support.apple.com/kb/ht1320
    Regards,
    - Brenden

  • Ipod touch 4th gen dead pixels

    Guys, my ipod touch 4th gen has a dead pixel lines in the upper portion of my screen and sad thing is its no longer within warranty? does reinstall will fix this or lcd replacement is the way to go?

    You can try a restore to factory settings/new iPod. You have nothing to lose.
    Replacing the screen may work but it could be a problem with the logic board

  • TS3572 My 4th gen ipod shuffle is either not working or dead...

    My 4th gen ipod shuffle is either not working or dead, i have opened it and found that its black near audio pin is injected and its heating while connecting via usb to laptop neeeeeeeeeeeeeeed help any one...............................
    i think its kind of short circuited is any thing workable in this device or not........

    I solved my problem by restoring the shuffle to factory settings on the summary screen. Now it seems to work the way it's supposed to. Many thanks to Apple for zero help, as usual. Apple should direct less resources to developing the next snazzy ipad and more to cleaning up and enhancing itunes. I'll make the same editorial comment about the iphone 4 voicemail options.

  • IPod 4th Gen completely dead

    iPod 4th Gen completely dead and will not appear in iTunes. iTunes works perfectly fine with other devices.

    Have you tried the standard fixes:
    - Reset. Nothing will be lost
    - Restore from backup
    - Restore to factory defaults/new iPod.
    However, ou may have a hardware problem like a dead battery and an appointment at the Genius Bar of an Apple store may be in order.

  • I attempted to updated my Ipod (4th Gen) to iOS 6 today on my computer. When updating an error occurred, it then said i needed to restore it so i did. It then came up with another error. Now, everytime i turn my ipod on, it asks me to connect to iTunes

    Today, i attempted to update my iPod (4th Gen) to iOS 6 on my computer. When it was updating it came up with an error, it then asked me to restore my iPod which i did. During this process it came up with another error. Now, everytime I turn on my iPod, it asks me to connect to iTunes. When i do this, it connects to the computer but doesnt show up in iTunes. How do i fix this?

    Error 2000-2009 (2001, 2002, 2005, 2006, 2009, and so on)
    If you experience this issue on a Mac, disconnect third-party devices, hubs, spare cables, displays, reset the SMC, and then try to restore. If you are using a Windows computer, remove all USB devices and spare cables other than your keyboard, mouse, and the device, restart the computer, and try to restore. If that does not resolve the issue, try the USB issue-resolution steps and articles listed for Error 1604 above. If the issue persists, it may be related to conflicting security software.

  • I just set up an Optus Cisco DPQ3925 wireless router to access higher speed internet I signed up for. I have a 4th gen airport extreme I want to put in another room and use as a wifi extender the wifi but I get an error message each time I try. Help?

    Hello all.
    I have just set up a new cisco DPQ3925 wireless router that Optus sent me to be able to access the higher speed internet I have signed up for.
    I have a 4th gen apple extreme that I want to use to extend the wifi but when I try to update the settings via the airport utility I get a message that says it cannot do so, and to check it is in range and the wifi is set up correctly. I'm not experienced with these things but I can't think what I have done wrong.
    Is anybody able to help me please.

    You cannot use the AE to extend wireless from a non apple router such as your cisco modem router.. they are not compatible..
    You need to tie to the two devices together either with ethernet or something like EOP adapters.. They are about $120 and you can price match in officeworks.

  • Help me - iPod Shuffle 4th gen is probably dead - red light for 5 seconds

    Hello,
    sorry for my bad english. I hope you can help me.
    I have iPod Shuffle 4th gen. I have it for one year. When I today tried to charge it, after connected to my PC (in the right USB port) I heard sound of connecting device but in Windows in My Computer nothing happened. On the iPod the diode emitted the red light for 5 seconds and then turned off. I have iTunes and iTunes doesn't recognize the iPod too.
    Does anybody know what is wrong?
    Thanks

    Hey StatistaXS,
    Welcome to the Apple Support Communities! It sounds like your iPod shuffle may have had a very low charge when connecting to your computer:
    iPod shuffle: Checking the battery charge - Apple Support
    http://support.apple.com/en-us/HT1510
    If the iPod does not turn on after charging for an acceptable amount of time, it may need to be serviced. But first, check out the relative steps in this resource:
    iPod shuffle troubleshooting and service FAQ - Apple Support
    http://support.apple.com/en-us/TS1412
    Thanks,
    Matt M.

  • I have an ipod touch 4th gen. charged twice battery went dead now will not charge or power on. what can I do?

    I have had my 4th gen ipod touch for over a yr. But I've only charged it twice now it wont charge or power up. I have had ppl try resetting it. But no change. Is there something I can do to fix it?

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • My iPod Touch 4th Gen won't charge?

    Well I've had my iPod Touch 4th Gen since it came out it will be 2 years old in October. Yesterday I charged my iPod while listening to music. I took it of when it was charged and used a little it became half dead so I put it on my charger. I realized there was no indication of it charging? I placed on all of the chargers in my house and the same problem. I haven't tried connecting it to my Mac, but I did try turning on and off but still won't charge. Does anyone know if I can fix this?

    - Try connecting it to yur computer and se if it charger and it it appears in iTunes
    - Try another cable
    - Look at the dock connector on the iPod. Look for abnormalites like bent or corroded contacts, crackd or missing plastic pieces or foreign material.
    - Also see:
    iPod touch: Hardware troubleshooting

  • IPod touch 4th gen that wont charge or show up in itunes.

    I have an iPod touch 4th gen. that wont charge. When I plug it in, it shows the battery with a little red at the one end and a lighting bolt ( the usual screen when charing the itouch after it is completely dead). I have left it in pluged in for a few hours but it never actually charges. Also when I plug it into my computer Itune won't recongnize it. The cords work fine I tested them with my other Ipods and everything worked liked normal. I have tried to restart it by holding the power and home button together but that doesn't seem to help either (again probably because it is dead). Thanks for the help.

    - See:      
    iPod touch: Hardware troubleshooting
    - Try another cable. Some 5G iPods were shipped with Lightning cable that were either initially defective or failed after short use.
    - Try another charging source
    - Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
    - Make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar      
    Also
    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • 4th Gen iPod LCD Screen

    I'm looking to purchase a working replacement LCD screen for my 4th Gen. iPod. ipodresq.com is quoting me $145. Does anyone know any better quote?

    My advice would be to save your money because before long something else in the iPod will fail. Send the broken one back to Apple for recycling. But if you really want to be a l33t haxor then see if you can find the make and model number of the screen and then search for it on Digikey. But you'll be lucky if you can buy just one piece from them. Another option would be to search ebay for dead iPods that have intact screens.
    good luck!

  • 4th gen i-pod locks up

    Almost a year ago the hard drive on my 4th gen I-pod failed complete with terrible clicking and grinding sounds (not surprising as I leave it in the car all the time, hot and cold). After $60 and 10 min I installed a new drive and all was well for several months. All of a sudden it started skipping to the next song by itself. This wasn’t so bad but then it started locking up, for 5 min, until the battery went dead or somewhere in-between. The display would lock up too and if the light happened to be on, that would stay on as well. I tried “restore to factory settings” several times from I-tunes and it would work for a while, an hour or a few days but then the symptoms would come back. It would also occasionally work after letting it unlock by itself. Unfortunately this happened on a solo road trip from NY to southern SC. I mostly use the unit connected to a USA-Spec factory car-radio adaptor but to rule that out as the problem, I used it stand-alone and the problems persist, and my wife’s nano works fine with the car adaptor.
    Any ideas on a solution would be appreciated, thanks

    Try connecting it to your computer, and with iTunes NOT running, reformat it using Windows. You can do so through a My Computer or Windows Explorer window. Use a full format instead of any options for a quick format.
    If that process completes, run iTunes and immediately run another Restore to install and initialize the iPod's software.

Maybe you are looking for

  • N97 Garbage? Nokia RIP

    I have for the last 4 yrs been a Nokia user from an early n80 to the buggy useless n97 here is the none response of the biggest mistake in my life/....N97 RIP..... an email i sent and got noe replys ....  This will be the second email now I have aske

  • After updating to ios 6.1.3 I cant send images through imessage

    Hello

  • Device registration rules backup

    Hi, I've spent a lot of time putting in device registration rules for different subnets. I'm already backing up the database and also the closest server rules / certificate authority using zman on the (linux) servers. What I'm not clear on is where t

  • Selecting the Planning Level for Statistical Forecast in S&OP on HANA

    Hello together, we currently face an issue regarding the statistical forecast in S&OP on HANA: The customer wants to implement an S&OP process containing the two steps statistical forecast (automatically calculated) and sales forecast (manually deter

  • No Print Option In PSCS3

    i have tried a number of options and files buy cannot get the print options to become availiable. i need help because i cant print tiff files any other way. time is of the essance. windows xp Thank you.      Kris