Another headache - "problem during multiplexing/burning - buffer underun"

Hello,
After many iDVD issues, I finally got the burning process of my DVD project.. half way through it spit my DVD out and gave me these errors:
"Errors were found during the burning process:
The recording device reported the illegal request: Buffer underrun. (0x21, 0x02.)
There was a problem during multiplexing/burning."
What is this supposed to mean and how can I just burn my DVD?!
Thank you
Chris

It's been awhile since I had this error crop up, but I know 2 things that caused it for me.
1) Bad DVD media. It happened a lot when I was using some cheap, off brand DVD-R's. More expensive Sony DVD's (white) are much better and more consistent. The time wasted with bad burns from bad DVD media is not worth the time.
2) It could even be a problem with your DVD burner going bad, but not as likely. I did have one SuperDrive replaced because I started having problems even with good, recommended brands of DVD media. However, try getting some better media first. Don't buy a lot. Try out a small package of DVD-R's or buy a disc from a friend to try out a brand.
Another possibility: Lack of sufficient, free hard drive space. Here's what iDVD 6's help file states:
"When you burn a DVD, iDVD needs temporary space on your hard disk to store the encoded files for your project. To burn your iDVD project to a single-layer DVD disc, you should have 8-10 gigabytes (GB) of free disk space on your hard disk, depending on the size of your project. For double-layer discs, you need 15-20 GB of free disk space."
Apple's support forum describes "buffer underrun" in more detail at:
http://docs.info.apple.com/article.html?artnum=25750
You might also want to defragment your hard drive (with a 3rd party utiility such as TechTool Pro) so that you don't have a fragmented hard drive when burning a project.
Speed rating of the DVD media- I've seen reports that some SuperDrives work best with media rated the same as it's maximum burn speed (e.g.- 4x, 8x, etc). I would recommend trying to find media that matches your SuperDrive burn speed, or no more than twice the burn speed.
I hope this helps.
You didn't mention which version of iDVD you were using or which operating system. Sometimes other users have tips for you based on that info.

Similar Messages

IDVD having problems "during multiplexing/burning"

Help please:
iDVD is not burning DVDs for me.
it goes through the whole process seemingly fine, then at the end shows the error message: "problem during multiplexing/burning".
I have a G4 emac. 800 Mhz 10.3.9
external Lacie dvd burner (that burns fine on wife's imac)
I was having this problem earlier, then erased the hard drive to start clean. Didn't seem to help.
I upgraded the Lacie driver, etc too.
thoughts?
R

Ah then if Toast has a connection issue and iDVD is having issues when burning, it would appear that your issue is unrelated to iDVD and instead a system or hardware problem. Unfortunately that might be too hard to diagnose here in this forum, at least not with a ton of non-iDVD related back and forth questions and answers.
Did you play the disc image on your computer to see if the titles made it into the disk image? My guess if they didn't make it onto the DVD blank, then they are not in the disk image either, although maybe they were?
Patrick

Problem during burning multiplexing/burning error appers, please help!

I made a movie in imovie that is 1 hour long and contains still pictures and video. It also contains music all the way through it. I exported it to idvd then tried to burn it. It took almost 7 hours for it to get to the burn phase and then it pops up an error saying "problem during multiplexing/burning".
I have made movies in the past and this never has occured, and I have 30GB of HD space.
Any thoughts??

you can use mp3 ...it will simply take longer to encode though ......
http://docs.info.apple.com/article.html?artnum=61636
btw ... don't convert mp3 to aiff (that would be doing things backwards). For example, read these links:
http://discussions.apple.com/thread.jspa?messageID=795036&#795036
http://discussions.apple.com/thread.jspa?messageID=1049799&#1049799
Hope this helps.

Multiplexer/burning error

I'v used idvd many a time but this time idvd goes right through it's process (rendering etc) and as its starts to burn to dvd a window scroll's down saying "BURNING FINISHED, Errors were found during the burning process. The Error -34506 was reported. Multiplexer error, There was a problem during Multiplexing/burning"

welcome Qbjoekinobe to the  board…
forum member John Beatty once answered/solved this problem:
http://discussions.apple.com/thread.jspa?messageID=1298733&#1298733

IDVD error message during Multiplexing

I'm trying to burn a project in iDVD 6. I think that my superdrive may be toast. Here is the error message:
Errors were found during the burning process
The recording device reported the media error. Power calibration area error
Multiplex error (ox73, oxo3)
There was a problem during mulitplexing/burning.
Does anyone know what would be wrong here? I can burn a data disc with no problems but when I burn to a DVD I get all sorts of problems. I never had this happen before. Any help would be greatly appreciated. Thanks!
-Chuck

Power calibration area error
This happens when your drives is doing a test burn on a portion of the disk reserved for this calibration.
When it fails, it means:
1) You have a failing drive
or
2) You have a bad blank DVD-R (or DVD+R, etc.)
or
3) You have a dirty laser lens on your drive.
Let's hope it's 2 or 3.
for 2 - Try another brand of DVD-R, I like Verbatim.
for 3 - use a CD/DVD lens cleaning disk, or another method to clean the drive. (NOTE - some users don't like these cleaning disks, and have claimed they have harmed their drives - obviously I disagree, but keep your cleaning disk as clean as possible!)
Try one of these, and then try making a data DVD from the finder. When this works OK , go back to iDVD. I always reccommend using "Save as Disk Image" and then burn the image with Disk Utility or Toast.
John B

IDVD ejects disk during multiplexing and burning

Having burnt many DVDs previously, I have suddenly started struggling.
Having edited in FCE HD v3.5.1, I export to Quicktime and then build the dvd as normal in iDVD.
The project has no errors and then I burn it using Verbatim 16x certified 4.7GB/120 min Advanced AZO+ DVD-R disks.
During Multiplexing and burning (with between 1 and 3 mins left, it ejects the disk saying saying done but nothing is burnt.
To try to remedy this, I have set the burn speed to both 2x and 1x. I have also turned the computer off, removed all cables and battery, held down the power button for 10secs then rebuilt and retried. Still nothing.
I saved a disk image but I don't know how to then make that into a burnt dvd. Any advice on that would be appreciated but moreover, I'm sure I shouldn't have to jump through so many hoops to burn a dvd - Mac's should just work shouldn't they.....?!

Here's even more of an update, with no joy....
to refresh, I have a macbook pro 15" - the older one with the silver keys.
I make 3 min movies in FCE then export using quick time conversion and try to burn with iDVD.
The problem: I can burn data CDs but i can't burn a DVD anymore. This seemed to start after the update to 10.5.7. At that point I tried to fix it with no joy so due to deadlines, used another machine! Now a few months later, i come back to it and still no joy.
I have reset the PRAM
I have reset the CMR
I have upgraded to Snow Leopard
I have sprayed compressed air into the drive
I have reduced the burn speed to 1x
But still I can't burn a dvd. When iDVD goes through the stages, everything is OK until it gets to multiplexing and burning, it says it is 'writing lead in' and has 1 min left (or 2 mins when burning at 1x). Then the blue status line suddenly goes all along and the machine spits the dvd out saying done. (although iDVD does not revert to beginning of the process, it kind of freezes).
idvd version 7.04 if I hadn't said before.
Please help, I'm despairing....

Dvd keeps ejecting during multiplexing and burning in idvd

Ok, I realize a lot of other people have had this problem and somehow managed to resolve it. I have done a lot of reading and experimenting but so far NOTHING has worked. So, to recount everything that I have tried and all the details to this problem:
First of all, I would like to mention that I have successfully burned a number of DVDs in idvd in the past. Then suddenly it just stopped working.
I have run a verify/ repair disk permissions. I have deleted all the idvd files off my computer, the .plist and preferences file, restarted, and reinstalled iDVD TWICE with a custom install. I have 500 gb of free space on my boot drive. I used a cleaning disc on my SuperDrive, and my regular DVD player. I switched to a better brand of blank dvd. I am now using Sony DVD-r, 4.7 gb discs although memorex DVD+r always worked just fine before. The project I am burning fits on the disc. I am not using chapters. I tried turning on the tv safe area and made sure everything was inside it, but still the same problem. I tried booting up in safe-mode then restarting. Still, same issue. I am burning at 2x speed, using professional quality setting. The project preview works just fine. It goes through the whole idvd process just fine, until the burning and multiplexing. After burning about 10 minutes of the project, the disc ejects suddenly. Idvd says "done" but then at the bottom it says "about one minute left" and the little burning wheel symbol is still spinning. The disc plays fine in my DVD player till about ten minutes in, then freezes and eventually goes back to the main menu. I can see on the disc that it is only partially burned.
Oh, and I have also tried saving to a disc image and burning with toast and disc utility. Once, this actually did work with toast and resulted in a playable DVD. The weird part was that I still got the error sense key message in toast and thought I had made another coaster, but when I tested the DVD it worked fine in my regular dvd player only (it was not readable in my xbox or ps2). Since that one fluke, however, it hasn't been successful. Disk utility did not work for burning the disc image. I am absolutely at a loss here...somebody PLEASE help.

I believe I have finally fixed the problem but I am going to post what I went through just in case someone else ever runs into these same issues, maybe I can save them some time. I went through so much troubleshooting and each problem solved seemed to result in new problems, so, let me recap.
First, computer was working fine. Burned a DVD, it worked. Then a few days later, tried to burn another DVD. It didn't work. I tried different brands of discs, different types of discs, (-r and +r) sometimes there was a partial burn, sometimes no luck at all and an unusable, unplayable disc. The disc would eject early during the burning phase, giving me simultaneous contradictory messages that it was both "done" and had " about one minute left".
I tried running a verify/ repair disk permissions. Everything came out fine, but still no burned DVDs. I tried uninstalling and reinstalling idvd. I tried a cleaning disc. Still no go. Sometimes idvd would crash or freeze on me or give me error messages. Result varied depending on what i tried, but were never good.
Then I bought an external drive and tried saving my DVD project as a disc image and burning with toast as many people have suggested. This worked! So, I concluded that my SuperDrive was faulty but I'm not going to bother getting it replaced right now because the external works just fine. I thought my problem was finally solved, but then...
I noticed that upon restarting, my computer would display a white-gray screen as is normal, with the familiar apple symbol, but now a new addition: a very annoying loading bar that took 5-10 minutes to load. Unacceptable!!! Also, I noticed shortly after that iTunes did not work. It wouldn't even open, but crashed due to an error and asked if it could send a report. I tried deleting and uninstalling iTunes but that didn't work.
I ran another verify disc permissions with disc utility, and I got a very bad error message. It said there were errors on the drive and it could not be repaired and it said I needed to start up from the Mac OS X install disc and use disc utility to repair the volume. Problem with that...my install disc says it can't install on this computer. I soon learned from one (finally) helpful apple support guy that the reason for this was that I am running snow leopard 10.6.8 and the disc that came with my computer was for 10.5.2 or something.
On a side note: I had called apple support before and specifically asked if the reason the disc didn't work was because it was for a different version and the guy said he had no idea if that was the reason or not. Jerk. CLEARLY, that was the reason and my ignorant butt didn't know any better and he wanted me to pay 19.99 just to answer that question for me.
So, I went to the apple store and purchased snow leopard. It was delivered today, I started my computer from the new snow leopard disc and repaired my drive. Restarted. A bit slow restarting but no more loading bar and not as bad as before...iTunes still didn't work but I completely uninstalled a reinstalled it again and this time it seems to be working fine. Idvd is working, I saved another movie to disc might. And am assuming it will still burn fine with toast in the external drive.
During my arduous troubleshooting I discovered that I most probably have the seagate 1 tb hard drive that was recalled by apple due to its tendency to fail...whether this has been the root of my computer's troubles from the start, I still don't know for sure. But, everything seems to be functioning correctly now at least and since my computer has lasted this long without hard drive failures, maybe it will be ok. It's possible that I somehow caused the errors while I was fiddling around on the computer trying to fix idvd and iTunes. Hope this is helpful to somebody, someday. I did gain a lot of advice from various forums on the web and found many people having one or more of the issues I was running into, so I thought I should record my process here for others as well.

IDVD ejects during multiplexing and burning

Hi folks,
I've used iDVD previously (several times) to create DVDs of movies I've created in FCE4. Today, the program goes so far, then ejects the disk during the "multiplexing and burning" / "writing lead-in" portion. When I check, there's nothing on the disk. Anyone every experience this? And, if you know, please advise as to how I might fix the problem.
Thanks very much for your expertise.
Vic

Multiplexing Error
Hi
Multiplexing error is a very complex problem due to many things (long long list following) - one common but not obvious reason is that material on the iDVD menu goes outside the TV-Safe area (or just touching it).
So first - turn on TV-Safe area and move any object well inside of this.
Wide screen stretched - usually (as I think) it is due to making a 4x3 movie in a 16x9 wide-screen project OR the other way around. This forces one to on flat-screen TV (or other) set the presenting view right - My has 4x3, wide-screen, zoom and auto-wide-screen and I have to switch this by my remote for some DVD I've made "wrong" way.
Now my long long list on Multiplex Error
LONG LONG LONG LIST
Multiplexing Error
PART One.
Use of strange video/audio material e.g. .avi, .wmv, .mp3 etc.
I only use.
Video - StreamingDV (miniDV tape via FireWire) and
Audio - .aiff (as on audio-CDs) (else converted to this .aiff 48KHz)
Photo - .jpg (.bmp known problematic)
Chapters !
A. Using strange letters in video project name e.g. +,/; etc. keep to a-z and 0-9 strange letters in project name e.g. +
as described by Donnyboy69. Does the title of your project have any symbols or decimal points in it. If so, that is why you are getting the error. I had a project that had a + sign which caused the same problem. I renamed it without the symbol and low and behold, it worked.
B. Location of Chapters
• Can’t be at start or end of movie (Skip first/start one - iDVD sets this by it self. At the End - no need)
• Not in a transition (or within 2-3 seconds from it)
Important when from iMovie HD6 or previous - Now also observed when using FCE 4
PART Two.
from Robert Modero.
"Multiplexing Error. Problem during initialization of tracks"
Simply remember to add subtitles to your Quicktime files and menu buttons.
Once I did that, I was back in business.
from Boise Jim
Do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
I always makes a DiskImage first and test this so that it runs OK
I use only - Verbatim DVDs
I use only - DVD-R
I burn at an as slow speed possibly e.g. x1
This gives good DVDs
PART Three.
Multiplex Error
Chuck, Chicago 2/7/2009.
Back again. Here is what I have found to work. I also have and use a LaCie DVD-R/RW DL external drive and a LaCie external hard drive as well. Since yesterday I have tried a few ways to burn a themed iDVD project having four 56 minute movies on it, amounting to 226 minutes onto a DVD DL disc, capacity 240 minutes. Apple tech support really didn't know what to do but gave me a very good tip. I had two options left. Apple tech support's tip was to try disc image. One of the replies on a thread with this subject said not to, but my experience today is good. Put your project onto "Burn to disc image," under "iDVD, file." Yesterday encoding took me 23 1/2 hours. Overnight for iDVD disc image, encoding took 21 1/2 hours (again) while I slept. This morning I tried to copy/burn disc image to a DVD with Roxio Toast 7, and it stopped near the end of the burn with some kind of "error" message. So then I tried Utilities> Disc Utility> Burn icon, and followed it through. Be sure to click the DVD DL drive in the window "Burn disc in.". I had one other problem though. At the end of a 46 minute copy, it started to verify, and at the end of verify it rejected the burn. So I tried again, and when "verify" appeared, I clicked on "Skip." The disc finished burning and is doing fine and well. A long and tortuous process, but at last something works. I made several additional copies using Disc Utility. Best wishes. Chuck, Chicago.
2. Disconnect any other external devices not absolutely needed.
e.g. external USB/USB2 hard disks, other FW hard disks etc.
3 Chapter marks in transitions - minimum 2 sec from
FROM Bev.
(Not a 'guy' but I will answer!)
First, I do not think that mixing wide-screen and standard makes a difference in iDVD.
Second, you should use a better brand of DVD disk. Also, many of us have experienced fewer problems on playback with DVD-R disks. Recommended brands here are Verbatim, Maxell and Taiyo Yuden. Memorex and TDK are not consistent and may not give you a correct burn. They apparently have fewer layers in the composition of the disk. I have always used Verbatim DVD-R disks and have not had any burn problems.
Also, choose a slower burn speed, 4x or less.
Third, to determine if the iDVD project will burn properly, create a disk image file (from within iDVD, go File->Save as Disk Image) and test it. Mount the disk image and then open DVD Player (in Applications) and view your project. If it plays correctly, you can then burn the actual DVD disk from the disk image file using Disk Utility.
From. Boise, Idaho
I did everything I've seen suggested, but a friend (who used to be an Apple Genius) suggested that I do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
It worked, and I got a clean burn from iDVD.
Hopefully this can help other people.
by dheb0422
Well, I finally got it, and it was odd enough to post here incase anyone looks this topic up again. Many things were tried, including burning the unedited film, the edited film without titles and chapter markers, abbreviating the chapter markers in case length was the issue (remember the old iMovie used to truncate them when moving to iDVD?). In the process, I noticed that one, and only one, chapter marker was on the same line as the title marker. All the others were on the line above. The only way I seemed able to change that was to clip a few seconds of film. After that last clip, the offending marker took a place on the line above, as were all the others. That run published, compiled completely and burned. That's one for the books.
One user more writes
To add my experience with Multiplex Errors using iDVD (7.0.4), I recently created two iDVD projects
Video from both passed from FCE 4.01 with chapters
One project worked fine in creating disk image file
The other gave Multiplex Errors
I tried suggestions to remove special characters and no chapter marks at beginning, but nothing worked
Note that I've used iDVD for dozens of projects and this is first time I've run into Multiplex Errors
Anyway, for problem project, I tried an experiment where I removed all chapters in FCE and passed to new iDVD project
This time multiplex errors gone
So had something to do with chapters
So now I tried numerous experiments to remove individual chapters and try again creating disk image with new iDVD project
After numerous tries, I was able to narrow problem down to 1 "Bad" chapter mark
That is, when I left the "bad" chapter in my FCE project and passed to iDVD, iDVD gave multiplex error
When I removed "bad" chapter mark (and others in), no multiplex error
As a final experiment, I moved "bad" chapter mark about 5-10 sec's beyond original point and passed to iDVD, the multiplex errors now magically went away and I was able to finally create my disk image.
I have no idea why this worked, but thought I'd mention here in case someone else runs into similar problem.
Rich839
In addition to Bengt's fine advice, burning errors can occur if you have located any of your menu buttons wholly or partly outside of the safe TV viewing area. Go to your main project menu, then click on View/Show TV Safe Area, to check. Drag into the safe viewing area any buttons that are outside the safe viewing area.
Russ One - suggest this
Multiplex Error-There was an error during muxing preparation
One thing that worked for me was to export the video w/o chapter markers as a self contained movie (thereby not loosing the edits & etc). Then make a new FCE project and import that movie into a new sequence and add the chapter markers. I've used "-", "&" and "," with no problem in the chapter names. Removing the markers or exporting without them did solve the problem but renaming them with just numbers 1,2,3....5, did not solve the problem and since this problem seems to happen with with iMovie as well, it would suggest the problem is in the video or audio and in combination with the chapter markers iDVD just can't handle it. The only other possibility is that both iMovie and FCE share the same or similar chapter marker code that some how is corrupting the markers.
Summary - What to try
1. Chapters
• Only A to Z and 0 to 9 in chapter title
• No Chapter mark at very beginning of movie
• No Chapter mark in or within 2 seconds from any transition in movie
2. TV-safe area for buttons (no one outside this)
3. Safe re-boot
4. No other external devices connected - that are not needed
SDMacuser adds to this
• On #4 ... No ext. devices. Some think this applies mainly to ext. FW. Not the case. Also applies to ext. USB2 as well (not to mention flash drives too).
Do not leave 3rd party devices / camera / camcorder plugged in unless it is being used with iDvd's One Step process. Certain web cams can trigger this also (especially ones with added features like LED light/s that draw additional power from the FW or USB bus).
5. Minimum of 25Gb free space on Start-up hard disk
6. Make a DiskImage first - reduces where problem originates
7. Trash iDVD pref. file
8. Make a new iDVD project
9. Movies in project with same aspect ratio e.g. 4x3 or 16x9
10. No other programs/applications running during iDVD process. e.g. Internet, screen & energy savers
Yours Bengt W

Burning ejects during "multiplexing and burning"

When I burn a dvd it goes the whole way and then with 10 minutes left when it is doing the "multiplexing and burning" part, it ejects before finished and I get a blank DVD. Tried a 1000 times. Has anyone else experienced this?
I've burned dvds before and had no problem.

Hi
My list on this
*Multiplexing Error*
PART One.
Use of strange video/audio material eg .avi, .wmv, .mp3 etc.
I only use.
Video - StreamingDV (miniDV tape via FireWire) and
Audio = .aiff (as on audio-CDs) (else coverted to this .aff 48KHz)
*Chapters !*
A. *Using strange letters* in video project name eg +,/; etc. keep to a-z and 0-9 strange letters in project name eg +
as described by Donnyboy69. Does the title of your project have any symbols or decimal points in it. If so, that is why you are getting the error. I had a project that had a + sign which caused the same problem. I renamed it without the symbol and low and behold, it worked.
B. *Location of Chapters*
• Can’t be at start or end of movie (Skip first/start one - iDVD sets this by it self. At the End - no need)
• Not in a transition (or within 2-3 seconds from it)
Important when from iMovie HD6 or previous - Now also observed when using FCE 4
PART Two.
from Robert Modero.
"Multiplexing Error. Problem during initialization of tracks"
Simply remember to add subtitles to your Quicktime files and menu buttons.
Once I did that, I was back in business.
from Boise Jim
Do a safe reboot (by holding down the shift key until you see the spinning gear on grey background, then release, then restart when your start-up screen appears).
I always makes a DiskImage first and test this so that it runs OK
I use only - Verbatim DVDs
I use only - DVD-R
I burn at an as slow speed possibly eg x1
This gives good DVDs
PART Three.
Multiplex Error
Chuck, Chicago 2/7/2009.
Back again. Here is what I have found to work. I also have and use a LaCie DVD-R/RW DL external drive and a LaCie external hard drive as well. Since yesterday I have tried a few ways to burn a themed iDVD project having four 56 minute movies on it, amounting to 226 minutes onto a DVD DL disc, capacity 240 minutes. Apple tech support really didn't know what to do but gave me a very good tip. I had two options left. Apple tech support's tip was to try disc image. One of the replies on a thread with this subject said not to, but my experience today is good. Put your project onto "Burn to disc image," under "iDVD, file." Yesterday encoding took me 23 1/2 hours. Overnight for iDVD disc image, encoding took 21 1/2 hours (again) while I slept. This morning I tried to copy/burn disc image to a DVD with Roxio Toast 7, and it stopped near the end of the burn with some kind of "error" message. So then I tried Utilities> Disc Utility> Burn icon, and followed it through. Be sure to click the DVD DL drive in the window "Burn disc in.". I had one other problem though. At the end of a 46 minute copy, it started to verify, and at the end of verify it rejected the burn. So I tried again, and when "verify" appeared, I clicked on "Skip." The disc finished burning and is doing fine and well. A long and tortuous process, but at last something works. I made several additional copies using Disc Utility. Best wishes. Chuck, Chicago.
2. Disconnect any other external devices not absolutly needed.
eg external USB/USB2 hard disks, other FW hard disks etc.
3 Chapter marks in transitions - minimum 2 sec from
FROM Bev.
(Not a 'guy' but I will answer!)
First, I do not think that mixing widescreen and standard makes a difference in iDVD.
Second, you should use a better brand of DVD disk. Also, many of us have experienced fewer problems on playback with DVD-R disks. Recommended brands here are Verbatim, Maxell and Taio Yuden. Memorex and TDK are not consistent and may not give you a correct burn. They apparently have fewer layers in the composition of the disk. I have always used Verbatim DVD-R disks and have not had any burn problems.
Also, choose a slower burn speed, 4x or less.
Third, to determine if the iDVD project will burn properly, create a disk image file (from within iDVD, go File->Save as Disk Image) and test it. Mount the disk image and then open DVD Player (in Applications) and view your project. If it plays correctly, you can then burn the actual DVD disk from the disk image file using Disk Utility.
From. Boise, Idaho
I did everything I've seen suggested, but a friend (who used to be an Apple Genius) suggested that I do a safe reboot (by holding down the shift key until you see the spinning gear on grey background, then release, then restart when your start-up screen appears).
It worked, and I got a clean burn from iDVD.
Hopefully this can help other people.
by dheb0422
Well, I finally got it, and it was odd enough to post here incase anyone looks this topic up again. Many things were tried, including burning the uneditited film, the edited film without titles and chapter markers, abbreviating the chapter markers in case length was the issue (remember the old iMovie used to truncate them when moving to iDVD?). In the process, I noticed that one, and only one, chapter marker was on the same line as the title marker. All the others were on the line above. The only way I seemed able to change that was to clip a few seconds of film. After that last clip, the offending marker took a place on the line above, as were all the others. That run published, compiled completely and burned. That's one for the books.
*One user more writes*
To add my experience with Multiplex Errors using iDVD (7.0.4), I recently created two iDVD projects
Video from both passed from FCE 4.01 with chapters
One project worked fine in creating disk image file
The other gave Multiplex Errors
I tried suggestions to remove special characters and no chapter marks at beginning, but nothing worked
Note that I've used iDVD for dozens of projects and this is first time I've run into Multiplex Errors
Anyway, for problem project, I tried an experiment where I removed all chapters in FCE and passed to new iDVD project
This time multiplex errors gone
So had something to do with chapters
So now I tried numerous experiments to remove individual chapters and try again creating disk image with new iDVD project
After numerous trys, I was able to narrow problem down to 1 "Bad" chapter mark
That is, when I left the "bad" chapter in my FCE project and passed to iDVD, iDVD gave multiplex error
When I removed "bad" chapter mark (and others in), no mulitplex error
As a final experiment, I moved "bad" chapter mark about 5-10 secs beyond original point and passed to iDVD, the multiplex errors now magically went away and I was able to finally create my disk image.
I have no idea why this worked, but thought I'd mention here in case someone else runs into similar problem.
Rich839
In addition to Bengt's fine advice, burning errors can occur if you have located any of your menu buttons wholly or partly outside of the safe TV viewing area. Go to your main project menu, then click on View/Show TV Safe Area, to check. Drag into the safe viewing area any buttons that are outside the safe viewing area.
Russ One - suggest this
Multiplexer Error-There was an error during muxing preparation
One thing that worked for me was to export the video w/o chapter markers as a self contained movie (thereby not loosing the edits & etc). Then make a new FCE project and import that movie into a new sequence and add the chapter markers. I've used "-", "&" and "," with no problem in the chapter names. Removing the markers or exporting without them did solve the problem but renaming them with just numbers 1,2,3....5, did not solve the problem and since this problem seems to happen with with iMovie as well, it would suggest the problem is in the video or audio and in combination with the chapter markers iDVD just can't handle it. The only other possibility is that both iMovie and FCE share the same or similar chapter marker code that some how is corrupting the markers.
Yours Bengt W

HT1645 whether i use a DL DVD or just a DVD R, it tells me there was an error during multiplexing. I have tried changing every setting, best performance, professional quality, etc. and still get the same error message every time i try to burn to dvd.

whether i use a DL DVD or just a DVD R, it tells me there was an error during multiplexing. I have tried changing every setting, best performance, professional quality, etc. and still get the same error message every time i try to burn to dvd.

Welcome to the forums.
Looks like that error message does refer to encoding (see http://support.apple.com/kb/HT1645) but a problem could be that your video has to be reloaded into iDVD if you started the encoding process and then switched settings. You could start a new iDVD project, or try deleting encoded assets.
Let's start from the beginning -- what length of video are you trying to fit on the DVD? (this will indicate what encoding options you have). Double layer DVDs can be finicky and are used for video more than 2 hrs long.
Use good quality media -- Verbatim is often recommended around here, and I've used Sony DVD-R with good results.
For a detailed treatise, see: https://discussions.apple.com/thread/3926901?tstart=0
John

Idvd burning problems during rendering/encoding

I have made several attempts to burn a dvd and when it gets to "step2: Menu and slideshow redering and encoding..." it never goes anywhere. If I cancel the process I get and error "error during rendering/encoding. there was an error during rendering/encoding of the menus/slideshows. Burning process aborted." The project is a 4 minute slideshow of pictures (jpegs) with one itunes imported song. The entire project was created in idvd and is no larger than 200megs. I have tried to burn this project on 3 different macs (2 G5s and a G4 powerbook) and they all have the same error so it must mean that I am doing something wrong. I have previewed the slideshow and it has no problems and am burning DVD-R's (tried a few different ones).

with one itunes imported song
Was this a iTunes Store purchased song?

Everytime I try to burn an iMovie project to a DVD with iDVD, the disc is ejected during the Burning and Multiplexing phase before it's completed.

For months I have been unable to burn any iMovie project to a DVD using iDVD. During the Burning and Multiplexing phase the disc is ejected before it's complete. I went the Genius Bar and after many tests I was told that my disc drive was pretty much dead. The person that helped recommended that I buy an external DVD burner from amazon. I bought the new drive and I can now burn files, but I'm still encountering the same issue burning a movie. Does anyone have any idea what'g going on? I'm extremely frustrated at this point!

Read this treatise on Multiplexing by Bengt Wärleby: HT1645 I was burning a DVD and the...: Apple Support Communities.
Follow this workflow to help ensure the best quality final product:
Once you have the project as you want it save it as a disk image via the File ➙ Save as Disk Image menu option. This will separate the encoding process from the burn process.
To check the encoding mount the disk image and launch DVD Player and play it. If it plays OK with DVD Player the encoding was good.
Then burn to disk with Disk Utility or Toast at the slowest speed available (2x-4x) to assure the best burn quality. Always use top quality media: Verbatim, Maxell or Taiyo Yuden DVD-R are the most recommended in these forums.
OT

Multiplexing/Burning Issues.

Grrr..iLife '06, what a dissapointment! I now have 3 machines that won't write DVD's..and yes, they did before. <end of rant>
On my Powerbook 1.33 (the only machine where iDVD doesn't almost immediately crash) it will go through a LONG rendering and encoding process and somewhere along the way spit the disk out with the messages: Burning Finished Errors were found during the buring process. The twirl down arrow then says: "The recording device reported the media error: Power calibration area error. (0x73, 0x03.)"
Other times it does the same thing with the message that errors were found in the multiplexing/burning process.
The program then continues 'burning' w/out a disk, is unresponsive and in most cases has to be force quit.
I've tried 2 different DVD's thinking I might've had a bad one.
Ideas?
G5 1.8, G4 PB, eMac Mac OS X (10.4.4)

Thanks for the response. I did all that (from that post earlier today..fonts and such) and believe it or not, the problem appears to be the media. I was trying to use printable Memorex DVD's and they just won't work on this machine... When I switched over to 'regular' Imation 8x DVD-R's.. The disk wrote just fine.
Now I gotta see if I can get this working on the G5 since it seems to like the printable disks just fine.
Weird stuff.

PE12 hangs during encoding/burn to file or disk. Dvd OK, AVCHD hangs

Good day to everyone.
I have a 55-minute project conaining images, SD video and few HD AVCHD. Trying to burn this onto a DVD at a AVCHD res.
Problem:
If I chose the "DVD: res, under the pull-down option of "publish+share", then, I have no problem encoding, burning the whole project onto a file or a dvd. But if I try to burn it as an AVCHD, no matter which setting (1440 X1080i, or 1080p etc.) i chose, forget it. one time it hung at 98% during encoding, other times, it kept hanging after encoding was completed, but got stuck at 1% during subsequent burn process (to file, not even an inserted DVD). I had selected either one of the file sizes (4 GB or 8GB) and checked the selection for "fit to .....". By hang I mean: after 8 hours it was still at the same spot.
Again, burning at standard dvd res works well. Burns to file, burns to dvd, no problem and the video looks fine. I even followed the suggestion of A.T. Ramono in one of his posts to another member and downloaded the ImageBurn software in order to isolate whether the issue is my burner or some where before that as i was trying to figure out what is going on.
I'd like to burn this project at a higher def as some of the pictures and vids are somewhat blury when I burn it as standard dvd res. Some images and vids are blury. I also see the same bluriness while during preview (before I even move to burn a copy), but if I pause during the preview, the video and images that were blury, crisp up to a perfect image.
My system is a Dell XPS, Wind XP, 4GB RAM, two HDs. Source on one with with 133GB of available, defragmented clean space left. OS, programs and rendered files etc all are on the other drive with 230GB of clean defrag available space.
Anyone can help me figure out what is going on?

Thank you John.
I read the post. But it trigered a follow up question.
While my intention is to burn a AVCHD copy onto a disc, I can't even get the burn completed when I chose "Burn to folder: (8.5GB)" AND I even check the box for "fit the content to available space" So, I would assume that if the physical space on an actual DVD is the problem, then by
1) checking the box that forces the media to fit the available space" and
2) that I'm burning to a folder, not a DVD media
I should have no problem. Right?
can you please elaborate ?
Thank you in advance.

Problem During Installation of ECC 6 on Windows 2003

Here I am facing problem during Import ABAP Phase.
It is throwing Error like that::
CJS-30022 Program 'Migration Moitor' exists with return code 103.
After completeing 9 stages, it's getting problem in Import packages and installation get stucked.
My Server is like that:
OS: Windows Server 2003
Hardware: HP Itanium IA64
Database: Oracle 10.2g
SAP Release : 2004s ECC 6
I have configured Java with j2sdk 1.4.2_12:
JRE 1.5 is not available for IA64 .
I reconfigured the parameter "shared_pool_size" (to 400MB)in init<sid>.ora at \oracle\<sid>\database.
Also adjusted another parameter which is "shared_pool_reserved_size" i.e. 10% of the shared_pool_size.
What to do now.
Please send me feed backs.
Regards,
Sumanta Chatterjee
 

run 'ls -lrta' in /tmp/sapinst_instdir/.... (whatever the lowest path is there, where all the log files are). You should see something like sap<something>.tsk and sap<something>.log. Look at the most recently updated sap<something>.log file for the specific error. One problem I've seen is that if you configure the advanced oracle config to turn off AUTOEXTEND on the tablespaces, the abap load will bomb because it runs out of space. Also, make sure your SYSTEM tablespace has at least 500M.
Posting the relevant contents of the log with the detailed error description would help us provide a better answer as well.
Rich

Another headache - "problem during multiplexing/burning - buffer underun"

Similar Messages

Maybe you are looking for