Another help request for K7N2-delta

I was trying to overclock my memory and when my system rebooted after saving my settings in the bios, I just get a black screen. On the D-bracket, the top two are red and hangs there, which, according to the manual, means that either my processor is damaged or not installed properly.
I tried rebooting in safe mode by changing my J10 jumper and clearing the cmos but to no avail. Could I have damaged my CPU just by changing a setting?
Specs:
CPU: AMD Athlon Barton 2500+
Motherboard: K7N2 Delta-ILSR
Video card: Saphire Radeon 9600 Pro 256 mb AGP
RAM: Corsair Value Select, PC2700, 256mb, 512 mb, and 1 gb of RAM.
Hard drive 1 & 2: Seagate, 120gb, ATA100
Hard drive 3: Western Digital, 500gb, ATA100
Windows XP SP2
Powersupply: Antec TruePower, 430w (3.3v/28a, 5v/36a, 12v/20a)

Quote from: Stu on 18-February-08, 02:21:22
Guys, the Insert key reset was for the K7N2-Delta2 series, which didn't have the safemode FSB jumper, it does not apply to the K7N2 Delta
You're asking for trouble by a) using cheap value-branded RAM, and b) mixing sticks of different sizes
Also you always get best results by running memory clock at same speed as CPU FSB clock.
Take out all the sticks of RAM and have just one installed, then see if it will start up again
I read a review of how well this memory overclocks, so I thought I'd give it a shot. Also, the value-brand for Corsair is rated just under their XMS series; it's solid as far as I can tell.
Anywho, I've always had the 256mb one in the slot ever since the incident anyways. Thanks for the warning, I never knew mixing different sizes had negative effects.
Quote from: Maxwell Smart on 18-February-08, 02:18:35
I own this board... it's not the insert key, but rather the delete key... so yes, as soon as your pc boots up, hit the delete key repeatedly (or hold it down) and then it will let you go into the BIOS.
I'll try that once I get home. Thanks for the info!
Quote from: HenryW on 18-February-08, 03:01:23
"I was trying to overclock my memory..."
There is a miss-print in your manual for the CPU D-LED, I had the same in my K7N2G-ILSR manual.
So it's stuck at the hard drive or at the system power on? I'm assuming the latter since my hard drive shouldn't be having any problems.
Yea, I don't know what I was thinking when I decided to try this. This is what I get for it, I guess.

Similar Messages

FOR K7N2 DELTA-L USERS: Mouse Hang At Win Startup? Check It Out!!

!!!FOR K7N2 DELTA-L USERS!!!!!
I had this same problem but i think i found solution. STEP 1 plug mouse to ps2 keyboard port and vice versa, if that will not help ... STEP 2 in bios set BOOT UP NUM LOCK LED to off and GATE A20 OPTION to normal that should help!!! it REALY solved my problem!!

Making a copy to Good Articles...

MOVED: need help with my k7n2 delta series motherboard please

This topic has been moved to AMD SocketA based board.
need help with my k7n2 delta series motherboard please

"...the other memory ive been using is memorymaxx 512mb ddr 3200..." If I understood right, your'e actually using both memories at same time so, your'e lucky if it works. We have said thousand times that mixing dif. brand/make/speed memories is a bad idea, most with this Mobo that is very picky about ram. If you want to avoid slowdown problems, stay with only one stick ( the better one ) until you can buy at same time in same store, 2 identical memories to replace the old one.

My KingMax SuperRam can't run Dual Channel for K7N2-delta

My KingMax SuperRam can't run Dual Channel for K7N2-delta
why??

How many sticks do you have?
Please post complete systems specs in your signature.

Need help with jumper settings for k7n2 delta ilsr

I have a k7n2 delta ilsr and I'm using a AMD 2800+ barton 333 fsb. I'm not sure what the jumper settins are for this cpu. The users guide only shows 133/166 and 200, can anyone help me with the jumper settings.
Thanks, Ron.

Hi,
As your processor is 333FSB - the jumper should be set to 166FSB as should the BIOS. As your RAM CPU combination runs at 2x166=333 or thereabouts.
Basically, as a general rule, if you halve the FSB speed of your processor you'll get the setting for both BIOS and Jumper. 200FSB=100, 266FSB=133, 333FSB=166 etc. etc.
Axel

Anyone help - need I/O plate for K7N2 Delta ILSR??

I'm based in the UK but will pay P&P worldwide........
cheers
D.

Good luck!
http://search.stores.ebay.com/ws/search/StoreItemSearch?catref=C5&fcl=3&from=R7&frpp=50&fsoo=1&fsop=1&sacat=-1&satitle=k7n2+delta+ilsr&sbrexp=WD1S&sif=1&sofindtype=0&sofp=4&ssPageName=WD1S
Edit: If applicable:
http://www.mycableshop.com/sku/ATXBACKPLATE.htm

Bios for K7n2 delta 2 LSR (2800+ Mobile Barton Recognizing)

Hi, i need the BIOS for the Bios for MSI K7n2 delta 2 LSR Motherboard, because i have a Mobile Barton 2800+ CPU with FSB 266 and it isn't recognized correct, i would like to set the Multiplier to 16, the highest setting is 13 - but at 13 my system didnt boot anymore. I tried the B72 Bios, but it didn't help. Thanks

What's that? You already asked for that in another thread (https://forum-en.msi.com/index.php?topic=123557.msg932826#msg932826). Please don't open various threads for the same issue.
I already said in the other thread you can't set 16 manually. Set it to auto.

New Modded BIOS for K7N2 Delta ILSR

MSI K7N2 Delta ILSR Modded BIOS based on Official v. 7.80 BIOS
download here:

Description: Access through interface which is on insecure interfaces list detected. Request aborted.
Interface/Client IP address:
Date: Wed, 18 May 2005 13:11:17 GMT
Doesn't work for me
By the way did u put the bios to vork with 1.3 vcore like the braziliantech one that does't exist anymore ?
EDIT: Thanks it's working now

Warranty info for K7N2 Delta Series Motherboards

I havent been able to find out weather my motherboard is still under warranty or not. i have checked the web site and found nothing, and i found nothing in the forums either. i dont know what infor you need to figure this out. but here is all the stuff on the sticker on my box:
P/N:6570-020
S/N:K0310079827
K7N2 Delta-L (601-6570-020)
K7, nFORCE2 Ultra400/SPP, MCP2, FSB400, D-Bracket2, Round cable
Thats all the info i have right now at my finger tips. if you need more il can find it.
Thank you for your help in this matter.
BTW: All i want to know is IF i can send my motherboard to MSI and get it replaced. and if i can, how would i go about doing it?

Quote
I havent been able to find out weather my motherboard is still under warranty or not. i have checked the web site and found nothing, and i found nothing in the forums either. i dont know what infor you need to figure this out....
I boutght it the USA. I hope it is still under warranty....i hate to ask, but i cant figure out where the rma page is. can someone help me out please?
Oh, BTW, i looked around for some contact info for MSI, but all i could find was a link to their web site.....From INSIDE the site itself!!!! The page listed all kinds of other companies, and thire addresses and phone numbers, but not MSI's. Anyone have any helpfull tips or hints?
Not to worry. I think I can be of some assistance here.
You might want to print these directions out because its a little confusing and you won't have to switch back and forth between windows to follow all the complicated steps:
1. Go to MSI USA Website
2. On navigation bar, click where it says "Customer Service/RMA"
3. See all the information you need right in front of you!

Jumper Settings for K7N2 Delta LISR and Athlon 3200 FSB400

Hello Everyone,
(I think I sent this to Raven By E-Mail but I'm not sure, I'm still new to this)
Having problems understanding jumper settings.
I cheched out the forum and the motherboard users guide to see which way the jumpers are set for my Board K7N2 LISR + Athlon 3200+ 400FSB.
In the user guide it say's:-
FSB Mode Jumper: J10
This jumper allows you to set the CPU FSB mode, (It then shows two diagrams of Jumper 10) - first with pins 1 and 2 jumpered "user mode default 133Mhz" and the secound shows pins 2 and 3 jumpered "safe mode 100Mhz".
What has settings 133Mhz or 100Mhz got to do with a 400 FSB??????
CPU FSB Frequency Jumper: J11
This jumper is used to specify the CPU FSB frequency. (again it shows two Diagrams) first: Leave the jumper short connected if a 133/166Mhz FSB is installed.
Secound:If the CPU supports 100Mhz FSB, leave the jumper open connected.
To use a 200Mhz FSB CPU, set the jumper short connected and enter BIOS setup Utility to adjust the CPU FSB Clock Frequency.
Again what has 133/166Mhz or 100Mhz got to do with a 400 FSB???????
For my K7N2 Delta LISR and Athlon Barton 3200+ 400 FSB, what Would I set J10 to:- (Jumpered Pins 1 and 2,= 133Mhz) or (Jumpered 2 and 3,= 100Mhz).
Also what would I set J11 to:- (Jumper pins Open = 100Mhz) or (Jumper short 133/166Mhz). Hope someone can help!!!!!!!!!
It would be nice if the User's Guide had a (If .... Then..... in it)
If CPU = Athlon 2800+ 333 FSB, Then J10 is jumpered pins 1 and 2,
If CPU = Athlon.... etc etc.... or even a couple of examples
Sorry this is so long, but I just need to tell someone, Thanks.

1 insafe mode it will boot at 100 fsb regardless of what you set in the bios
in user it will boot by what it sees the cpu as or what you set it to in the bios
just leave it in user
if you o/c and it will not boot shut down put it in safe
then lower the o/c once it boots
again shut down and put it back in user
2 just leave it shorted
only alter it if you used a 100 fsb cpu

AGP Setup For k7n2 delta ilsr

I have a k7n2 delta ilsr mb, in display properties on desk top setting tab then advanced button then GeForce tab under adapter information is Bus and memory. To the right of Bus it reads AGP (PCI mode) shouldn't that read AGP (8X), how can I change this. Ron.

Hi,
No, leave it at 64 or 128.
Go here for an explanation:
http://www.rojakpot.com/default.aspx?location=7&var1=18
Then - Click on: "Free Access To the BIOS Optimization Guide" near the bottom of the page - then click on "AGP Aperture Size"
Axel

Kingston HyperX Memory for K7N2 Delta-ILSR

Hey will my K7N2 Delta-ILSR support the Kingston HyperX serises DDR400-512MB Ram?
Im looking to buy 2 maybe 3 of these and really want to be sure theyll work.
http://www.ec.kingston.com/shop/partsinfo.asp?ktcpartno=KHX3200A/256&promo=hx2shp
I checked the supported ram list for the K7N2 Delta-ILSR and they wernt on there so i just figured it may be out of date?
So thanx in Advance for info!
p.s. It will support 3x 512MB right?

Has anyone noticed how the Hyper X went from the poor-man's Corsair to being priced equal to OCZ, and usually higher then Geil, as well as usually being very close to Corsair, if not the same? I think only Mushkin beats it out now price-wise...

Linux for K7N2 Delta-ILSR

Hello,
Does anyone know of with Linux distro is compatible with the K7N2 Delta Series?
Sincerely, Deft

Knoppix worked too, even my TvTuner worked.
Not that I would recommend Knoppix as a solution, I was just playing.
There is a lot more support for the nvidia kit now.

Case Recommendation for K7N2 Delta-ILSR

Greetings,
I'm looking for a mid size ATX case that that has the front usb etc. ports prewired as to work easily with a K7N2 Delta-ILSR mb. By that I mean I don't have to plug each wire individually (with names that don't match) just a plug that goes on the mb. My eyesight isn't as sharp so hooking up those one wire at a time is tediuous. Not to mention the lack of starndards Does anyone know if this is address on the next rev of mb's (with pcix etc).
Thanks

Brazos,
I have yet to see a case that has all the USB wires together, they are all 1 pin at a time. You will find the Antec line of cases very good. (You can always use a magnifying glass to see the pins.) The pin names on the Antec cases are standardized and easy to figure out.
If you want a good case at a cheap price, then go with the SLK3700AMB:
If you want a good high end case, then go with the Sonata:
If weight is an issue, then go with the Super Lanboy:
Take Care,
Richard

Warranty Length for K7N2 Delta-ILSR

What is the mfg's warranty length on the K7N2 Delta-ILSR?
I filled out the online support form earlier today but no response as of yet, and me being the impatient rascal I am, I didn't want to wonder all weekend. I bought it October, 2003 and the floppy drive controller seems to have gone out.
Thanks!
HH

Thank you, Glenn!
Looks like mine is 2 yrs. & 4 months old. Kind of stinks that I lost 5 months on the warranty by going by the mfg. date instead of date of purchase. Its not worth the hassle & would even cost more to RMA it for the controller. Ahh, but this is IT, the "World of Workarounds". I'll live!
Thanks for your time, Glenn!
HH

Another help request for K7N2-delta

Similar Messages

Maybe you are looking for