Another very low broadband speed connection

Hello all.
Got the BT Home Hub3 installed last November and was pleased with 4.5-5Mb speed but since around Christmas the speed seemed to continually halve until right now it is consistently around 0.4Mb.
There has been no other installations relating to the phone line either.
I have tried disconnecting other devices using the phone plus reconnecting the router to the other phone socket but no difference and gone through the simple troubleshooting advice.
Here are Hub settings-
ADSL settings
VPI/VCI:
 0/38
Type:
 PPPoA
Modulation:
 G.992.1 Annex A
 Latency type:
Interleaved
 Noise margin (Down/Up):
16.7 dB / 24.0 dB
Line attenuation (Down/Up):
23.0 dB / 16.0 dB
Output power (Down/Up):
19.8 dBm / 11.9 dBm
FEC Events (Down/Up):
1964 / 21
CRC Events (Down/Up):
37 / 13
Loss of Framing (Local/Remote):
 0 / 0
Loss of Signal (Local/Remote):
 0 / 0
Loss of Power (Local/Remote):
 0 / 0
Loss of Link (Remote):
 0
HEC Errors (Down/Up):
268 / 11
Error Seconds (Local/Remote):
 0 / 0
What do you think then?

I am not sure about socket. I can see phone cable outside from computer and it goes around the house presumably to the main telephone we use downstairs.
Download speedachieved during the test was - 410 Kbps
 For your connection, the acceptable range of speeds is 50-500 Kbps.
 Additional Information:
 Your DSL Connection Rate :3776 Kbps(DOWN-STREAM), 448 Kbps(UP-STREAM)
 IP Profile for your line is - 500 Kbps
Connection information
Line state:
 Connected
Connection time:
 0 day, 01:43:27
Downstream:
 3,776 Kbps
Upstream:
 448 Kbps
ADSL settings
VPI/VCI:
 0/38
Type:
 PPPoA
Modulation:
 G.992.1 Annex A
Latency type:
 Interleaved
Noise margin (Down/Up):
 1.0 dB / 0.0 dB
Line attenuation (Down/Up):
 15.4 dB / 24.0 dB
Output power (Down/Up):
 23.0 dBm / 16.0 dBm
FEC Events (Down/Up):
187 / 284
CRC Events (Down/Up):
 388 / 311
Loss of Framing (Local/Remote):
 7 / 0
Loss of Signal (Local/Remote):
 0 / 0
Loss of Power (Local/Remote):
 0 / 0
Loss of Link (Remote):
 0
HEC Errors (Down/Up):
 335 / 267
Error Seconds (Local/Remote):
 0 / 0

Similar Messages

  • Low broadband speeds, connection keeps dropping

    Recently I have seen broadband speeds drop from about 11mb to about 2. this is coupled with the home hub 4 constantly dropping the connection and the orange power light flashing orange.
    Bt have been here but claim no problem on the line.
    I am starting to think this is related to the latest firmware upgrade. Is there anyway to roll back to test this theory. Or does anyone have any other suggestions.
    Thanks
    James

    welcome to the BT community forum where customers help customers and only BT employees are the forum mods
    in order for the forum members to help please can you post the adsl stats from your router you may need to 'show detail' to get all stats (if hub enter 192.168.1.254 in your browser and navigate to adsl or if HH4/5 then go to troubleshooting then logs and you are looking for 2 line together when hub last connected to internet and they will show your connection speed and noise margin or if netgear enter 192.168.0.1). Then run  btspeedtester  (MAC users may have problems). when first test completes then run diagnostic test and post the results ( do not reset the router).
    Lines should look like this
    19:11:29, 07 Nov. (2290101.460000) DSL noise margin: 7.00 dB upstream, 6.10 dB downstream
    19:11:29, 07 Nov. (2290101.390000) DSL line rate: 448 Kbps upstream, 288 Kbps downstream
    are you connected directly via a filter to the NTE5 master or test socket or to somewhere else? Is the master the only phone socket in your home?
    Have you tried the quiet line test? - dial 17070 option 2 - should hear nothing - best done with a corded phone. if cordless phone you may hear a 'dull hum' which is normal
    Someone may then be able to offer help/assistance/suggestions to your problem
    If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
    If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

  • Very low broadband speed

    Hello
    I rejoined BT three weeks ago having spent two years with Zen. I was with BT prior to that and had moved to Infinity with sppeds of about 26Mbps - not great but adequate.
    Nothing changed when I moved to Zen. Obviously the cabling and exchange was the same and no upgrade or modernisation has been carried out. The speed therefore remained the same.
    I have had problems though since I moved back to BT with the broadband dropping out regularly. After about 8 calls to India taking up hours of my time and two engineer visits the fault has apparently been rectified.  
    Quite what was wrong seemed to chamge on a daily basis from a "missing port" in the Excchange to "noise on the line" to a "problem with the cabling on the telegraph pole".
    The issue though now is the speed which has dropped to about 9Mbps. This seems bizarre if nothing has changed at the excahnge or with the cabling and is certainly nothiong ner the promised 30Mbps?
    Peter Atkinson

    I reported the faulot and they are noiw saying that it's the Router.
    Bizarrely though I came home at 2 today and the internet is back up and running.
    It has got even slower though. It's now just over 8Mbps which is nowehere near what Infinity should be.
    I've done the Wholsale Speed Test and it tells me: 
    Download speed achieved during the test was - 8.25 Mbps
     For your connection, the acceptable range of speeds is 6.81 Mbps-8.52 Mbps .
     Additional Information:
     IP Profile for your line is - 8.52 Mbps
    This cannot be right as it reached 27Mbps just over a month ago
    2. Upstream Test: -provides background information.
    Upload Speed
    2.02 Mbps
    0 Mbps
    20 Mbps
    Max Achievable Speed
    Upload speed achieved during the test was - 2.02Mbps
     Additional Information:
     Upstream Rate IP profile on your line is - 20 Mbps

  • Very slow broadband speeds

    Hello
    My first post, and I'm hoping that someone will be able to help me with this.
    For a few days now, I've been experiencing very slow broadband speeds (100kbps or less), in contrast to the 1.5 - 2Mbps that I would usually expect to get.  I've been on hold to BT technical support for some time, and have got through twice, on both occasions being told that this is a widespread issue and to wait until the next day. However, I'm not seeing any improvement.  I'm aware of the problems in Edinburgh and the North of England,but I'm in East Anglia.
    speedtester.bt.com shows:
    Your configured download throughput speed for this service is 135 k
    and then:
    Two consecutive attempts have failed to initialise an Assured Rate session for your service.Please raise a fault with your service provider stating that the Performance Tester tool indicated a problem with initialising your Assured Rate session. <script type="text/javascript">// paintProgressAndMessageTestBar(-1,""); paintProgressAndMessageOnBar(-1,'An Error has Occured! '); // </script>
    My hub stats are:
    ADSL line status
    Connection information
    Line state Connected
    Connection time 1 day, 13:59:54
    Downstream 1,504 Kbps
    Upstream 448 Kbps
    ADSL settings
    VPI/VCI 0/38
    Type PPPoA
    Modulation ITU-T G.992.1
    Latency type Interleaved
    Noise margin (Down/Up) 15.0 dB / 19.0 dB
    Line attenuation (Down/Up) 60.0 dB / 31.5 dB
    Output power (Down/Up) 16.6 dBm / 11.9 dBm
    Loss of Framing (Local) 0
    Loss of Signal (Local) 0
    Loss of Power (Local) 0
    FEC Errors (Down/Up) 4586 / 92
    CRC Errors (Down/Up) 297 / 2147480000
    HEC Errors (Down/Up) nil / 72
    Error Seconds (Local) 221
    I hope this is enough information, but I'll happily supply anything else if I can.  The uptime of 1.5 days is the time since I was advised to restart / reset to defaults etc.
    Thanks for any help.
    Deej.

    Once a line is stable and working well, it's best left running 24/7
    Interventions like resets, replacing accelerators, unplugging the router etc. will cause line "flapping"
    And the dslam sees this as instability, and in turn the BRAS lowers the IP profile ....
    This is done to achieve stability, and decrease throughput purposefully, all done automatically.
    What you have to do, is cure any line noise, plug directly into the master or test socket behind the NTE
    faceplate, leave it connected and wait for the throughput to increase.
    Very often a rock bottom IP may need a kick to get it out of the doldrums.
    Eventually the noise margin will decrease, sync will increase, and IP profile go up.
    Depending on how long the line has suffered impulse noise, will determine the time for SNR to come down.
    Regardless of which type of phone you used to test quietline ... hum or crackle is a no-no.
    It may be the cause of the problems.  It could be REIN on the network portion of the connection or dslam
    crosstalk, either way it needs to be reported as line noise before you can count it out of the equation.

  • Sync lr and lr mobil without creative cloud? Speed up with very low internet speed in China?

    Sync lr and lr mobil without creative cloud? Speed up with very low internet speed in China?

    The Internet is the only way to synchronize Lightroom and Lightroom Mobile. It's unfortunate that you have a slow Internet connection.

  • VERY slow broadband speeds (0.76mbps) Phoneline?

    VERY slow broadband speeds (0.76mbps)
    Options 
    on 28-10-2012 12h38
    ROUTER STATISTICS
    System Up Time: 0:08:24
    Port Status TxPkts RxPkts Collisions Tx B/s Rx B/s Up TimeWANLANWLAN
    MER
    2351
    2177
    0
    136
    104
    0:00:56
    324
    0
    0
    0
    0
    0:08:24
    6762
    6743
    0
    164
    132
    0:07:57
    ADSL Link Downstream UpstreamConnection SpeedLine AttenuationNoise Margin
    766 kbps
    414 kbps
    48.5 db
    27.1 db
    15.7 db
    16.3 db
    I'm with Sky, and have had very slow broadband for a while now. Above are the statistics from the test socket. Sky seem to think there is a problem with the line. I've now plugged the router into the main socket. 
    Any help would be appreciated. 
    **EDIT** My phone line is with BT, my broadband is with Sky. The problem Sky says is with the phone line it seems. 

    Hi Joe,
    Try sticking your telephone number into this line tester page and let us know if it finds a fault. If it comes back clear, you'll need to go back to Sky as there'll be no issues with your telephone line. If it comes back with a line fault, we can get it progressed towards a fix
    Dean
    BTCare Community Mod
    If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
    If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

  • TS3899 Upgrade to ios6 got the following problems in my ipad2 . Very low download speed. Can not open my apple mail in my iPad.

    Upgrade to iOS 6 encountered the following problems in my ipad2.
    (1) very low download speed
    (2) I can not open my apple gmail in my iPad.
    (3) I can't download new apps from Internet.

    Have tried your suggestion of toggling but unfortunately that has not solved the problem - but many thanks for the suggestion.
    Regards
    Sailorfrank

  • Low Broadband speed = line fault?

    Hi,
    We have had a very slow download speed since the high winds started last week (live in a rural area about 1 mile from exchange).
    I have run through the BT Broadband speed wizard & not improved the speed.
    ADSL Speedtest results are:
    Download speed achieved - 194Kbps
                               Acceptable = 50-250Kbps
                               DSL 3424Kbps (downstream)
                                          448Kbps (upstream)
                               IP Profile = 250Kbps
    Now, I don't know what it was before - but this appears to me to be pretty slow!
    If I understand the notes correctly? for 3424Kbps we should be getting 600 to 7150Kbps throughput speed?
    All I know, is that pages are taking an age to load...
    Any thoughts on what to do next please?
    PS After restarting the Hub 2.0, we got the following results:
    ADSL line status
    Connection information
    Line state
    Connected
    Connection time
    0 days, 1:20:46
    Downstream
    5,120 Kbps
    Upstream
    448 Kbps
    ADSL settings
    VPI/VCI
    0/38
    Type
    PPPoA
    Modulation
    ITU-T G.992.1
    Latency type
    Interleaved
    Noise margin (Down/Up)
    12.3 dB / 23.0 dB
    Line attenuation (Down/Up)
    48.0 dB / 29.0 dB
    Output power (Down/Up)
    19.7 dBm / 11.9 dBm
    Loss of Framing (Local)
    0
    Loss of Signal (Local)
    0
    Loss of Power (Local)
    0
    FEC Errors (Down/Up)
    2701 / 0
    CRC Errors (Down/Up)
    64 / 2147480000
    HEC Errors (Down/Up)
    nil / 0
    Error Seconds (Local)
    16
    Appears faster on paper - but still as slow loading pages!
    Solved!
    Go to Solution.

    Hi again,
    As promised, we have left on 24/7 & not re-set etc. Although it seems to have re-set itself a few times.
    I am amazed at the low 480 Kbps speed! It is usually around 5400 Kbps...
    Test1 comprises of Best Effort Test
    Download  Speed
    243 Kbps
    0 Kbps
    500 Kbps
    Max Achievable Speed
     Download speedachieved during the test was - 243 Kbps
     For your connection, the acceptable range of speeds is 50-500 Kbps.
     Additional Information:
     Your DSL Connection Rate :480 Kbps(DOWN-STREAM), 448 Kbps(UP-STREAM)
     IP Profile for your line is - 350 Kbps
     ADSL line statusConnection information
    Line state
    Connected
    Connection time
    1 day, 15:47:51
    Downstream
    480 Kbps
    Upstream
    448 Kbps
    ADSL settings
    VPI/VCI
    0/38
    Type
    PPPoA
    Modulation
    ITU-T G.992.1
    Latency type
    Interleaved
    Noise margin (Down/Up)
    29.3 dB / 19.0 dB
    Line attenuation (Down/Up)
    47.0 dB / 29.0 dB
    Output power (Down/Up)
    15.3 dBm / 11.9 dBm
    Loss of Framing (Local)
    14
    Loss of Signal (Local)
    28
    Loss of Power (Local)
    0
    FEC Errors (Down/Up)
    26086 / 1
    CRC Errors (Down/Up)
    1766 / 2147480000
    HEC Errors (Down/Up)
    nil / 1
    Error Seconds (Local)
    7085

  • Very slow broadband speed and random disconnection...

    I have a problem with my home hub and broadband connection. The download speed is ridiculously low at only 768 kbits per second. I have been running speed tests all week and the speed has been getting gradually slower and slower starting at around 1.4mbits and lowering to between 0.4 and 0.8 mbps.The broadband is also losing connection every so often.
    This has been happening for a few weeks now, ever since the broadband and phone lights on my Hub turned orange, then continually flashed orange, went green then went off and then back to orange, flashed orange, then green then off and this cycle repeated until I restarted my Hub. Upon restarting the power light turned solid red and did not change. So I restarted it again. This time it rebooted properly (or so it seems to have). Before this the hub was (still slow) around 2mbps although this was much better than the speed now.
    I have a BT home hub version 1.5. I am on Bt Broadband option 3 meaning I should have unlimited broadband. Reason why I am asking for help is I am getting lag when ever I play games on My xbox 360 or browse on my laptop.  Im in scotland, dundee in the DD2 post code area if that matters.
    I have not tried plugging directly into the main telephone socket yet but as I have been using BT for well over 4 years and not had as little speed as this Im doubtful its due to interferance.
    Any help would be fantastic. I just want to be able to play my **bleep** xbox again
    Here is the DSL information. I have recently restarted my Hub (due to the broadband cutting out again). This is why the uptime is so low.
    DSL Connection   
    Link Information
    Uptime:    0 days, 0:29:27
    Modulation:    G.992.1 annex A
    Bandwidth (Up/Down) [kbps/kbps]:    448 / 768
    Data Transferred (Sent/Received) [MB/MB]:    19.28 / 20.58
    Output Power (Up/Down) [dBm]:    12.5 / 13.5
    Line Attenuation (Up/Down) [dB]:    27.5 / 47.0
    SN Margin (Up/Down) [dB]:    23.0 / 13.5
    Vendor ID (Local/Remote):    TMMB / IFTN
    Loss of Framing (Local/Remote):    0 / 0
    Loss of Signal (Local/Remote):    0 / 0
    Loss of Power (Local/Remote):    0 / 0
    Loss of Link (Remote):    0
    Error Seconds (Local/Remote):    0 / 0
    FEC Errors (Up/Down):    0 / 1,216
    CRC Errors (Up/Down):    0 / 0
    HEC Errors (Up/Down):    0 / 0
    Line Profile:    Interleaved
    Aut inveniam viam aut faciam

    Quick update: Well, I moved my hub and have plugged it into the master test socket... Couldn't connect at all wirelessly, so I had to phone up the BT helpline, they changed the wireless channel and I got on after that (however the assistant said that my plugging into the socket should not have disabled the wireless.) As for the speed, well, needless to say there is little to no improvement. I cannot post my DSL stats, as I cannot even connect to my home hub via the ip address and the bthomehub.home address as the connection times out.
    The speedtester on the other hand is working. Here are those results:
    1. Best Effort Test: -provides background information.
    Download Speed
    409 Kbps
    0 Kbps
    500 Kbps
    Max Achievable Speed
     Download speedachieved during the test was - 409 Kbps
     For your connection, the acceptable range of speedsis 100-500 Kbps.
     Additional Information:
     Your DSL Connection Rate :4704 Kbps(DOWN-STREAM), 448 Kbps(UP-STREAM)
     IP Profile for your line is - 500 Kbps
    The throughput of Best Efforts (BE) classes achieved during the test is - 8.62:28.39:63.06 (SBE:NBEBE)
    These figures represent the ratio while sententiously passing Sub BE, Normal BE and Priority BE marked traffic.
    The results of this test will vary depending on the way your ISP has decided to use these traffic classes.
    2. Upstream Test: -provides background information.
    Upload Speed
    307 Kbps
    0 Kbps
    448 Kbps
    Max Achievable Speed
    >Upload speed achieved during the test was - 307 Kbps
     Additional Information:
     Upstream Rate IP profile on your line is - 448 Kbps
    I have noticed that the DSL downstream speed has shot up remarkably (by about 4000) since plugging it in to the test socket, but for some reason, the IP profile is still very low, I would have expected it to have went up at least a little but it has remained the same for the past 2 days now should I be concerned with this or give it some more time?
    Oh and I have an engineer coming to the house on friday, turns out when my parents were installing the broadband accelerator they inadvertently knocked out the wires to the extensions and now none of the extensions in the house are working so I hope he or she can resolve things with my speed and I will update on Friday evening, and again next Wednesday(after the 5 day period) to see if the IP profile speed has improved.
    Aut inveniam viam aut faciam

  • Very low IP profile + connection keeps dropping

    I started having problems with my connection speed over in December 2010, we had a connection speed of 135kbps for 10 days.  This was then resolved and we had an IP profile of about 2mbps for 3 months.
    Since April my IP profile has varied between 135 and 350kbps. The error reported in April was simply cleared from My BT without any resolution to the problem and we have been living with these low speeds for months.
    Last Friday (8 July 2011) the connection disappeared altogether and I phoned BT to log a new fault. We use a homehub 2 and have a wired connection to a PC. It seemed possible that either the cable or socket on the home hub was faulty and after I swopped that out broadband connection was reestablished.
    We have only one telephone socket on this line, which is fitted with the special plate with 2 ports one for the telephone and the other for the router. During the 2 hours spent on the phone on Friday I unscrewed this front plate and am now connected using a microfilter to the test socket behind.
    The line connected at 3776kbps downstream but we only have an IP profile of 350kbps. I was informed that BT second line support would ring back the next day to help further. They did so  , said they were restting things at the exchange which would take 3-4 hours and it should all be stable 24 hours later. They promised to phone back to check the next day. I have heard nothing further from BT.
    My IP profile remains at 350kbps. After reading comments on this forum I found the stats on the home hub manager and we had continuous connection for almost 4 days with the IP profile remaining at 350kbps. Unfortunately yesterday the connection dropped and reconnected at least 3 times, and today has done the same at least twice. Each time it reconnects at very similar downstream speeds of between 3.6mbps and 3.8mbps. IP profile remains 350k.
    I emailed BT yesterday re the problem and have had no contact apart from the automatic acknowledgement. i have included all the stats I can think of as relevant including the current post in My BT fault tracking.
    As my connection seems to keep dropping ( I have not manually reset the hub since July 8th whilst on phone to India) then it seems unlikely we will ever reach the magic 5 days to have an IP profile restored.
    One last thing, we are located only about 0.5 miles from the local exchange.
    I would really appreciate help in sorting this out.

    Connection dropped again while I was not at home this morning, so back to only an hour since last reset. I have copied an extract of the event log from the hub again around the time it happened.
    The event " danube_dsl_ioctl:88: Failed ioctl ... " seems to be appearing in my homehub event log several times in the minute or two preceeding the homehub disconnecting and resetting.  Presumably this has some meaning and could help identify my problem?
    I did receive a phone call from India yesterday (13th July) assuring me that my emails had been received and escalated, and that someone who could help with my problems would phone by 15th July. But if I hadn't been contacted by 15th I should definitely phone BT again!

  • Very slow broadband and connection keeps dropping

    Hello, we have been BT customers since August 2013, after previously being Freeola customers for many years.  We live in a very rural area, at the end of the exchange so we are never going to get amazingly fast broadband, we are estimated 1MB. 
    Previously using Speedtest.net at the beginning of the year we were getting 0.9Mbps, then in May our internet dropped and we couldn't get a proper connection or speed.  We contacted Freeola who after doing some tests, said that we had a copper line failure and to contact BT.  We did this and the copper line failure issue was fixed, an openreach engineer tested the line and we assumed all was fine.  But we were still getting very slow speeds and the connection kept dropping.  So we decided to switch to BT in August, we have put up with the slow speeds and dropping connection for 3 months hoping in vain that once we got a stable line the speed would increase and we would be back to were we expected to be.
    When we are using the internet, we very often get "Your connection has been reset" errors within our browsers.
    This has not happened, so I have decided to come on to this forum in the hope that we can solve this issue before my hair gets any greyer.  We have a BT Home Hub 4 so we have not got all the stats that previous HH had available. 
    Also as we are in a rural area our telephone connection is through overhead cables and as said previously we are at the end of the exchange.
    Please see below for the information that I have been able to get:
    Home hub stats:
    17:28:52, 28 Oct. ( 68.040000) DSL noise margin: 12.00 dB upstream, 9.50 dB downstream
    17:28:51, 28 Oct. ( 67.970000) DSL line rate: 448 Kbps upstream, 192 Kbps downstream
    Internet Connection Configuration
    Connection Information
    Connection time:
    4 days, 22:01:39
    Data Transmitted/Received:
    221.4 MB / 2.3 GB
    Bt Wholesale Broadband test:
    Download Speed: 0.02
    Upload speed: 0.34
    Ping latency: 0.00
    Further diagnostics:
    Master socket is
    I performed the quiet line test which wasn't too bad there was a very slight crackle, but it was with a wireless phone.
    Speedtest.net results:
    Ping: 463ms
    Download:0.13mbps
    Upload: 0.28mbps
    As said previously before the copper line failure we were regularly getting download speeds of 0.9mbps.
    Any help would be greatly appreciated.
    Solved!
    Go to Solution.

    Hi jacoma,
    Sorry to hear that your  having issues with your BT Retail services.
    You will either be on the ADSLMax (upto 8mbps) service or if your exchange has been BTw 21cn upgraded you maybe on the ADSL2/2+ (upto 12/20mbps) service depending on your line quality and length.
    However these upto speeds may not be the speeds you will get as ADSL broadband connections are very dependent on the distance from your property to the exchange and the quality of your line. The further away you are from your local exchange the slower your broadband speed will be.
    To enable the community to help you please see the advice below:
    Please see Keith's help guide here: Helping forum members to help you, it will go through some checks that are needed for us to help you.
    1) Are you in the TEST socket? if not can you please connect to the test socket and repeat steps 2, 3 and 4.
    All the below performed in TEST Socket:
    2) is there any noise on your line. dial 17070 option2 ,called quite line test, from landline phone. should be silent but slight hum normal on cordless phone.
    If there is any noise on your line such as crackling, distictive noise when the phone is connected to the TEST socket and doing the quiet line test then you need to report a line fault to BT Retail by dailling 151. Once the crackling or disticive noise has gone then your broadband should slowly recover.
    3) please post adsl line statistics 
    4) Can you please run a BT speed test (including IP Profile) http://speedtest.btwholesale.com (not beta version)[Best done with a wired, Ethernet, connection] After Quick Test is done you need to click "Further Diagnostics" to get IP Profile.
    ADSL Line Statistic Help:
     If you have a BT Home Hub like the one below...
     Then:
     1) Go to http://192.168.1.254 or http://bthomehub.home
     2) click Settings
     3) Click Advanced Settings
     4) Click Broadband
     5) Click Connection or sometimes called ADSL (see picture Below)
    The direct Address is http://bthomehub.home/index.cgi?active_page=9116 (for bthomehub3.A firmware ending in 1.3)
    or http://bthomehub.home/index.cgi?active_page=9118 (for bthomehub3.A firmware ending in 94.1.11)
    You will need to copy and past all the adsl line statistics ( Including HEC, CRC and FEC errors). You may need to click " More Details"
     If you have a HomeHub 4 then the majority of the ADSL Stats shown in the previous Hubs will not be there.
    for HH4 users you can go to hub manager then select troubleshooting then logs and are look for 2 entries together which will show theconnection speed and noise margin for when your HH4 last sycned with the exchange.
    There are more useful links on Keith's website here: If you have an ADSL connection, please select this link
     cheers
    I'm no expert, so please correct me if I'm wrong

  • Low broadband speed (narrowband)

    On the 14th of January I lost my telephone service and obviously my broadband.
    I telephoned the help line with my mobile phone  and after speaking with an Indian lady in India for 45 minutes she said she was going to run some tests and please would I not use the telephone or the broadband while she did it.  I informed her that I had said right at the beginning that my telephone and broadband was not working, se then said that she now had to pass me onto a different department!
    I was put through to another lady this time in England who told me what the problem was in 2 minutes. Why can’t you have your call centre in this country so that the staff can understand the problem?
    On Wednesday 19th January an engineer called to fix the telephone line and I can now use the land line telephone. 
    That evening I switched on my computer and the broadband was working but extremely slow, I called the broadband help line and they ran some tests and got me to do some things like re-cycling the router etc. 
    I borrowed a router (the same as mine) from my friend who lives 3 doors away, we plugged my router and then afterwards tried his straight into the master socket, we tried 2 different computers and 2 filters, all had the same symptoms broadband speed or 135 kb/s.
    An engineer was sent out on the 1st of February and he said that he would not leave until it was fixed.  He left saying that I would have up to 11 MB/s within 24 hours.
    Today I have 250 KB/s 
    I have now spent in excess of 8 hours on the phone and I have not got anywhere.
    Every time I phone the broadband help i am told that I have to wait another 24 to 48 hours for it to fix itself
    It is now Saturday 6th February and my download speed is 144 kb/s 
    I have now been without broadband for 24 days
    My line speed is 11 Mb/s but the download speed is capped at 250 kb/s (from the bt speed test)
    How many more weeks do I have to wait - nobody at BT cares
    I am a very unhapy non user.

    If the password on the card which was shipped with the homehub doesn't work or the password page doesn't let you in, try and reset your home hub (Stick a pen into the little red button and press it) and then try what John says
    Like this post? Give it a Star . If this post answers your question, please Mark it as the Accepted Solution.

  • Slow broadband speed/connection dropping.

    Hi, I discovered yesterday that my Hub was unable to connect to broadband, this was around 5pm, at around 7-8pm, the hub was then able to connect to broadband, but with painfully slow speeds, (under 1Mbps download). Connection ha not been any better today and regularly cuts out before reconnecting. Until around 5pm the broadband cut out completely, and did not reconnect. Much like yesterday's problem. It can't be a line fault without our house as the phone works fine, and the broadband was reaching 7Mbps downloads before Wednesday. It's as if BT have come out and downgraded the line. Infact, I'm writing this message using a BT Openzone hotspot from another router in my street, which is capable of 3Mbps download speeds, much faster than what my Hub is able to manage.
    Obviously can't give ADSL stats as there is no connection to the Broadband.
    Any ideas as to what the problem might be, and how to solve it?

    Hi Welcome to the forums
    Here are some help pages done by CL Keith http://www.btinternet.com/~cbeddoe/wireless/hub3_wireless.html
    If you post the full stats from your router
    For homehub – type 192.168.1.254 into your browser
    Navigate to ADSL Settings or use the A-Z at the top right of the home page and scroll down to ADSL Settings and click on it
    Click on More Details and then post the full results.
    also post the full results from http://speedtester.bt.com/
    Have you tried connecting to the test socket at the rear of the master socket
    Have you tried the quiet line test? - dial 17070 option 2 - should hear nothing - best done with a corded phone. if cordless phone you may hear a 'dull hum' which is normal
    also you could try the hints given by poster RogerB in this link they may help http://community.bt.com/t5/BB-in-Home/Poor-Broadband-speed/m-p/14217#M8397
    Then someone here may be able to help and offer more advice.
    This is a customer to customer self help forum the only BT presence here are the forum moderators
    If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

  • Very Erratic Broadband Speeds

    Hi everyone,
    About a month ago, my broadband speeds went down to around 1.5mb from around 6.5mb. I rang Bt and they said that my profile was incorrect so they reset it again.
    The speed went back to normal for about a day, and ever since then, the speed has been very erratic, averaging about 2mb, but with the speeds sometimes going back to 6.5mb and sometimes going down to 0.8mb.
    This is very strange as 6 weeks ago we consistently received a speed of 6.5mb at all times.
    I have tried resetting the hub, changing filters etc and nothing is working, BT say there is no fault at there end, but the fact that the speed does sometimes go back to normal, proves that there must be an issue.
    I ran a wired bt wholesale speed test & diagnostic a couple of hours ago so that should be logged with BT.
    Does anyone have any ideas?
    Many Thanks, Adam

    welcome to the BT community forum where customers help customers and only BT employees are the forum mods
    in order for the forum members to help please can you post the adsl stats from your router you may need to 'show detail' to get all stats (if hub enter 192.168.1.254 in your browser and navigate to adsl or if HH4/5 then go to troubleshooting then logs and you are looking for 2 line together when hub last connected to internet and they will show your connection speed and noise margin or if netgear enter 192.168.0.1). Then run  btspeedtester  (MAC users may have problems). when first test completes then run diagnostic test and post the results ( do not reset the router).
    are you connected directly via a filter to the NTE5 master or test socket or to somewhere else? Is the master the only phone socket in your home?
    Have you tried the quiet line test? - dial 17070 option 2 - should hear nothing - best done with a corded phone. if cordless phone you may hear a 'dull hum' which is normal
    Someone may then be able to offer help/assistance/suggestions to your problem
    If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
    If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

  • Capped (very slow) broadband speed after line repa...

    Hello,
    I have just had my BT line repaired due to a fault on the line 400 metres from my property. However, although the line is now fine and there is no crackling and a normal dial tone, my broadband speed seems to be capped at 273 kbps download and 811 kbps upload speeds. It won't go any faster. Before I would get roughly 2.5mb. My noise margin is 8db (it has always been quite low) and line attenuation is 58.5db (I am a fair way from the exchange).
    Is there any way to manually reset the IP profile so that it goes back to normal or do I have to wait until the exchange server thinks my line is "stable"?
    Any help much appreciated...
    Many thanks.
    Solved!
    Go to Solution.

    welcome to the BT community forum where customers help customers and only BT employees are the forum mods
    from the information you have provided you are on 21CN adsl2 and your profile will be correct as it changes as and when your conenction speed changes.  problem is probably your low connection speed
    in order for the forum members to help please can you post the adsl stats from your router may need to 'show detail' to get all stats (if hub enter 192.168.1.254 in your browser and navigate to adsl or use a-z, if netgear enter 192.168.0.1) and run  btspeedtester  (MAC users may have problems). when first test completes then run diagnostic test and post the results .
    are you connected directly via a filter to the NTE5 master or test socket or to somewhere else? Is the master the only phone socket in your home?
    Have you tried the quiet line test? - dial 17070 option 2 - should hear nothing - best done with a corded phone. if cordless phone you may hear a 'dull hum' which is normal
    Someone may then be able to offer help/assistance/suggestions to your problem
    If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
    If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Maybe you are looking for

  • Datasocket and Shared Variables

    I am curious if there is any advantage to using Datasocket to read/write shared variables (as opposed to a direct read/write).  I'm specifically talking networked shared variables here. Is there any speed advantage to accessing shared variables thru

  • Path_to_install

    Hi all what is the purpose of /etc/path_to_inst in network?

  • InputsourceXML String to XML fields

    Hi Experts, My requirement is to convert the Input XMLstring into XML fields.Actually the original XML comes in <Payload> field as a string.I want to convert it to XML fields.How to achieve it through java mapping?Please provide your suggestion. Rega

  • All possible combinations of 23 columns in a table.

    Hi, We have a table as follows; CREATE TABLE ALL_PROD_COMB_TMP HDLM_ID NUMBER(10), MULTIPATH_ID NUMBER(10), TRUE_COPY_ID NUMBER(10), UVM_ID NUMBER(10), TUNING_ID NUMBER(10), CLUSTER_ID NUMBER(10), MIDDLEWARE_ID NUMBER(10), TAPE_ID NUMBER(10), THIRD_P

  • How do i find out what sequence preset i need to use???

    ive been looking all over the internet for this answer and cant find it anywhere! theres a ton of info about sequence presets but i cant seem to figure out what sequence preset to use for my Sony handycam DCR-HC32. if i could get any help it would be