Any known compatibility issues with disabling onboard sound and using

I have the K7 N2 board and disabled on board sound in the bios to use my Turtle Beach Santa Cruz. Sound seems to work fine in Windows Xp and the few games I have installed so far. My problem is with UT2003. When I try to launch the game I get the splash screen then it simply goes away. When I checked the system folder and looked at the debug log it shows the following.
Exception code: c0000005
Exception address: 77f51f2c 0001:00000f2c C:WINDOWSSystem32
tdll.dll
Call stack:
   77f51f2c 0001:00000f2c C:WINDOWSSystem32
tdll.dll
   77f5268e 0001:0000168e C:WINDOWSSystem32
tdll.dll
   77f52631 0001:00001631 C:WINDOWSSystem32
tdll.dll
   7639131d 0001:0000031d C:WINDOWSSystem32IMM32.dll
   77f5e52d 0001:0000d52d C:WINDOWSSystem32
tdll.dll
   77e798cc 0001:000188cc C:WINDOWSsystem32kernel32.dll
   77e7990f 0001:0001890f C:WINDOWSsystem32kernel32.dll
   7c00442a 0001:0000342a C:Program FilesUnreal Tournament 2003SystemMSVCR70.dll
   77e814c7 0001:000204c7 C:WINDOWSsystem32kernel32.dll
I am able to run UT in safe mode without sound. I yanked my Santa Cruz card and uninstalled the drivers and tried with on board but still had the same problem. Since disabling the sound allows me to play, it has to do something with either the on board or my card or some sort of incompatibility between the two. Anyone know of any issues? On a side note. If I was to wipe my drive and use the on board is the quality of the sound as good as using a separate card? Any help would be appreciated.

Just a follow up...I figured I could spend countless hours trying to figure out why UT wouldn'l load or spend 3 hours wiping the disk and reinstalling software. The latter proved to be worth it. My preference would have been not to install any of the audio drivers at all, but since they are bundled with the system drivers there is really no choice. The one thing I did differently was not to install the live drivers from the disk that came with my board but rather update to the newer Nforce 2 system driver dated 2/25/2003.
So the install went Xp Pro, Sp1, Video drivers, newest system drivers, disable on board sound in bios, Santa Cruz drivers then UT2003 and the game loads fine. I still get the message about the game port not having enough resources but that can be ironed out.
Hopefully this information can help someone else out who might experience conflicts going forward.
A side note..I find that with two network cards (3Com and on board) that Xp will spend about three mintues after it loads non responsive as it looks for the other network connection. Running the network wizard on box 1 connected to the internet and creating the network disk and running it on the other machine allowing the on board card to see the network and eliminates the painful lull after Xp load to the time I can do anything.
Thanks for the timely responses. I'm really enjoying this board. So many options, so little time.

Similar Messages

Hi Are there any known compatibility issues with Lopic Pro 9 and Adobe PDF 9?

Hi I am am Using a MacPro OS 10.5.8 2x2.66 GHz Dual-Core Intel Xeon and Logic 9.1.5. Also Adobe PDF 9.0
I can't print my score to pdf. The print box openes but The print button and the preview butten are not responsive!
Is any body else experiencing the same issue?
T.

Only Logic Pro 9.1.8 is officially supported under Mavericks. So: update!

Any known compatibility issues with Norton Antivirus for Mac v.11

I sometimes work freelance for a company that requires freelancers to have an antivirus program on their computers regardless if they are macs.
Anybody know if there are any known compatibility issues with mac Norton Antivirus v.11 and snow leopard?
thanks

Big time. Do not, do not install anything Norton. Your system will be mucked. Comply with the company request and use ClamXav.
http://www.macupdate.com/app/mac/15850/clamxav

Are there any known compatibility issues with iMac and Google Chrome?

Does anyone know of any compatibility issues with iMac and Google chrome. A Facebook friend who is a photographer posted recently that Chrome had ruined his iMac. He stead that it ran an update on itself that made safari and chrome unusable - slow running overall. In the end he had to reinstall his OS.
Is anyone aware of this and should I un-install Chrome off my Mac?
Thanks,
S.

There is nothing official but your post will attract a variety of personal experiences. I once loaded Chrome and found myself with the dreaded MacKeeper malware, loads of pop ups and conflicts with my system. Part of the problem is the huge range of add ons you are tempted to take on, many of which are not as strictly tested as Apple extensions. I would say, unless you have a specific reason, leave it alone. The best browser is Firefox and for Macs, Safari is OK.

Any known compatibility issues with snow leopard and cs3 creative suite

have leopard and want to upgrade to snow leopard..but am worried about any conflicts with photoshop cs3 and fireworks cs3? Does anyone use this version and have problems?

The extracts below are from http://snowleopard.wikidot.com/
I couldn't see any mention of a CS3 version of Fireworks.
Anecdotal information is variable; some seem to have no problems, others found CS3 unusable, so it's difficult to be categorical for you. Certainly Adobe only consider CS4 and above to be fully compatible.

Known compatibility issues with 2008 and 2008 R2

For some reason i am not able to make remote connections from VS 2013 to my current installation of SQL server 2008 so i thought to uninstall it and install another edition i got from MSDN but i the uninstall process keeps failing saying theres a known
compatibility issues with 2008 and 2008 R2. it also gave me the option to seek solution online but when i click on it it is unable to get a solution online and i am never able to uninstall it. please help me here. i need to get SQL server up and running. thanks

Hi FLORENCEOKOSUN,
According to your description, you encounter a compatibility issue when uninstalling SQL Server 2008. For further analysis, please help to post the full error message and
SQL Server summary log. By default, the log can be found in: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log.
There is also a KB article about known issues of installing SQL Server 2008 on Windows Server 2008 R2 for your reference.
https://support.microsoft.com/en-us/kb/955725
Thanks,
Lydia Zhang
Lydia Zhang
TechNet Community Support

Compatibility issues with Final Cut Express and Final Cut Pro

I'm getting ready to edit a project and I was wondering if there are any compatibility issues with Final Cut Express and Final Cut Pro. I've never used Express put I assume I would be able to make cuts, simple effects and titles. Is this correct.
If I transfer project files from one platform to the other will i run into any issues?
Thanks for all and any help.

{quote:title=cuttingedge wrote:}
If I transfer project files from one platform to the other will i run into any issues?
{quote}
Although they operate in a similar fashion that are not fully compatible. You can open a FCE project in FCP, but once you've edited it in FCP you can't go back to FCE.

How to enter bios, disable onboard sound, and install a sound card

How do I enter bios, disable onboard sound, and install a sound card?

Hi,
You may also have to disable, security for the PCIE x1 slot.
Windows 8.1 - Accessing the UEFI (BIOS) Setup
Regrads

Compatibility issues with 1st Ipod Nano and In Car Windows MP3 media player

I use a mac pro running 10.5.6 leopard. My new car has a Windows formatted media MP3 player with USB connector which doesn't read my 1st generation Ipod nano. I can load the music files onto a flash drive and play them in the car but without any of the functionality of an Ipod.
How can I load music files onto my Ipod and use it in my car without
resorting to loading Windows on my mac and reformatting my Ipod to PC? Is
there a crossover bit of software available? Are more recent nano's formatted for both Mac and PC? I have saved the IPod as a external hard disk and converted all music files to MP3 which is the MP3's accepted format. I'm also sure I have the latest software for the IPod. Any ideas? Cheers.

OK I am confused. You say your car stereo has a Windows formatted MP3 player? What does that mean exactly? That the car stereo can play MP3s off of mass storage devices plugged into its USB port?
I think if the above is what you meant, then you have two problems. One is that your car stereo likely reads FAT32 formatted storage devices (and possibly, but doubtfully, Windows NTFS formatted devices). Your iPod is likely formatted in Mac format which your stereo won't be able to read.
That can be overcome. Simply restore your ipod on a Windows machine to put it into Windows format then plug it back into your Mac and use it that way. Macs can read and sync to Windows formatted iPods just fine.
But the other problem is, your stereo may not be able to actually control an iPod directly. Does the instruction say it can? Therefore it would be looking on the storage of the iPod that shows up as Mass Storage for tracks, not on the hidden area where iTunes stashes music into and your iPod plays music from.
Patrick

Installed Lion, any known compatibity issue with Adobe CS4

So far so good, everything seems OK but was concerned with Photoshop CS4 as I had heard maybe some issues, anyone had any good/bad experiences?

it appears as though their may be some issues. Read what Adobe has to say :http://blogs.adobe.com/crawlspace/2011/07/photoshop-and-lightroom-compatibility- with-mac-os-x-10-7-lion.html Hope this helps

Compatibility issue with itunes 10.6 and windows 7

I just installed the update to itunes 10.6 on windows 7 64bit, and it says that it is not compatible with my theme (so it switches it back to the windows 7 basic) I normally wouldn't mind however my screen blacks out and it's really annoying. I don't have any compatbility settings checked off at the moment. However I did try changing them and it still doesnt work.
Itunes worked just fine before the update...

Okay. Sometimes that can indicate a stuck registry key.
Try labnut2's instructions from the following post:
Re: How do I turn off the compatibility mode for ITunes.

Iphone 4s. Windows 8.1 hp laptop. Itunes does not see my phone when I plug it in or launch itunes. My other computer sees it no problem, Is there compatibility issues with win 8.1 and itunes? Very frustrating...

Need help getting itunes to recognize my 4s, my older other computers have no issues. I have hp 2000 with windows 8.1..

That didn't work for me....I have done every concievable action to resolve this....now I am getting pissy......Went through all the suggestions on the support page....I am going absolutely nuts here, uninstall, reinstall, set this default to that....NO ONE KNOWS WHY THIS IS HAPPENING OR IT WOULD BE ADDRESSED ALREADY!!!!!!
Sitting right next to my new laptop is the old one that started out with XP on it. Has Win7 and itunes fires right up. I called my brother, he doesn't have apple products. He just bought a new laptop and did the 8.1 upgrade and guess what? Itunes still won't recognise my 4S....
ANY FEEDBACK WOULD BE GREAT. However, keep in mind I have done everything except throw the laptop and the phone.....
IF IT AIN'T BROKE DON'T FIX IT!!!!!!!

Any known 'porting' issues between 8.2.2 and 9.0 ??

Hi all,
we are in the process of evaluating LS ES2 (9.0) and would like to know if there are any 'porting' issues between the two versions. Asked another way, are there any issues in deploying a 8.2.2. LCA onto 9.0 ?
Dan

8.2 LCA's will run fine in 9.0 if they are just deployed into it. But in 9.0 a new application model has been introduced, so in order to make changes to anything after you've migrated it you'll need to create an application and migrate your processes and resources into it. You may want to take a look at the Leveraging Legacy Solution document available online. Here's the link: http://help.adobe.com/en_US/livecycle/9.0/workbenchHelp/help.htm?content=leveragingLegacy. html .
Chris

Compatibility issue with Nikon's D700 and Aperture downloading RAW files.

Need a little help with this one - purchased a NIKON D700 (today) and tried to download RAW files into Aperture - got a bad message - unsupported image format - (shows on a reddish background)
I worked on the problem for about 4 hours, both with the software and the camera, but to no avail... upon inital download you see a small image but the message occurs when the image is clicked on.
Thank you in advance for any comment or idea you might have.... occurring

You will have to wait until Apple updates the MacOS to recognize the D700 in its RAW profile. It's not listed yet:
http://support.apple.com/kb/HT1475
You'll have to shoot JPEG or use Nikon's software until Apple gets around to it. Maybe try Lightroom.
eemka wrote:
Need a little help with this one - purchased a NIKON D700 (today) and tried to download RAW files into Aperture - got a bad message - unsupported image format - (shows on a reddish background)
I worked on the problem for about 4 hours, both with the software and the camera, but to no avail... upon inital download you see a small image but the message occurs when the image is clicked on.
Thank you in advance for any comment or idea you might have.... occurring

Issue with RAM/SWAP available and used

Hi,
In production environment I have a server whit OS version Solaris 10 10/09 s10s_u8wos_08a SPARC (SunOS 5.10 Generic_142900-14 sun4v sparc SUNW,SPARC-Enterprise-T5120) that I can not understand the behavior of free/used memory and swap used/available. Following the ouput command that run:
swap -l
swapfile dev swaplo blocks free
/dev/zvol/dsk/rboot/swap 256,1 16 33554416 33534256
swap -s
total: 9555680k bytes allocated + 1658320k reserved = 11214000k used, 13441384k available
vmstat 3 3 kthr memory page disk faults cpu r b w swap free re mf pi po fr de sr s0 s1 s2 s3 in sy cs us sy id
0 0 0 13272120 1309136 43 173 0 0 0 0 0 3 3 -0 2 2113 4910 2352 1 0 99
0 0 0 13456480 645128 4 33 0 0 0 0 0 4 4 0 0 1899 3473 1929 0 0 99
0 0 0 13455112 643848 62 270 0 0 0 0 0 0 0 0 0 1628 4685 1411 1 0 99
prtconf –v
Memory size: 16256 Megabytes
df -klZ
Filesystem kbytes used avail capacity Mounted on
rboot/ROOT/s10s_u8wos_08a 140378112 7091492 95820301 7% /
/devices 0 0 0 0% /devices
ctfs 0 0 0 0% /system/contract
proc 0 0 0 0% /proc
mnttab 0 0 0 0% /etc/mnttab
swap 13440280 1712 13438568 1% /etc/svc/volatile
objfs 0 0 0 0% /system/object
sharefs 0 0 0 0% /etc/dfs/sharetab
/platform/SUNW,SPARC-Enterprise-T5120/lib/libc_psr/libc_psr_hwcap2.so.1 102911793 7091492 95820301 7% /platform/sun4v/lib/libc_psr.so.1
/platform/SUNW,SPARC-Enterprise-T5120/lib/sparcv9/libc_psr/libc_psr_hwcap2.so.1 102911793 7091492 95820301 7% /platform/sun4v/lib/sparcv9/libc_psr.so.1
fd 0 0 0 0% /dev/fd
rboot/ROOT/s10s_u8wos_08a/var 140378112 3737396 95820301 4% /var
swap 13441240 2672 13438568 1% /tmp
swap 13438616 48 13438568 1% /var/run
rboot/export 140378112 23 95820301 1% /export
rboot/export/home 140378112 2084894 95820301 3% /export/home
rboot/product 73400320 18733136 54667184 26% /opt
product-pool 140378112 68558024 71815166 49% /opt/app
rboot 140378112 97 95820301 1% /rpool
My processes take up 10 GB of Ram, (sum all processes memory size with the ps auxwww command).
My questions are:
1) Why the vmstat output display only 643 MB of available ram ( free ram) ?
2) Why the swap -s output, the sum of used plus available is not equal to physical memory (16 GB) plus disk swap (16GB)?
Please help me for understand this issue
BR
Francesco
Edited by: Francesco Maisano on 28-mag-2012 16.25

Francesco Maisano wrote:
My processes take up 10 GB of Ram, (sum all processes memory size with the ps auxwww command).
My questions are:
1) Why the vmstat output display only 643 MB of available ram ( free ram) ?
2) Why the swap -s output, the sum of used plus available is not equal to physical memory (16 GB) plus disk swap (16GB)?
1) There are things in the kernel that will allocate memory at will (like file system cache) and as long as you have not met the scan threshold, the memory pages will not free up. This is no cause for alarm. IT just skews the results. Deal with it. We all do.
2) You must be referring to the statement in the manpage "These numbers include swap space from all configured swap areas as listed by the -l option, as well swap space in the form of physical memory". The key element in the statement is "swap space in the <b>form of physical memory</b>" which is <b>not</b> physical memory but a small part of it.

Any known compatibility issues with disabling onboard sound and using

Similar Messages

Maybe you are looking for