Anyone got a crucial SSD working MBP 17?

Had a Crucial M4 512 working my 2.0ghz MBP15 but the logic board went out. Got a refurb 17 MBP for dirt cheap...and it's slightly newer then the 15 I had...but when I put the Crucial M4 SSD in it...it will not recognize it. If I put the drive in anything else it boots right up, so we know it's good.
Seems odd that a slightly newer (in design) MBP 17 would struggle where a MBP 15 doesn't.

Thanks Bob. I have to run to the Apple store tomorrow to have them test out the logic board on my MBP15 that this MBP17 replaced...I'll ask them about their knowledge of bad SATA cables and issue SSD based on your comment. Thank you.

Similar Messages

Has anyone got cn8202temp_controller.vi to work?

Hello,
Has anyone got cn8202temp_controller.vi to work. I got it from the Ni website and I've been unable to get it to run right. If there is anyone out there that has got it to work please tell me how you did it. It has an error when you upload the parameters for the recipe. I have enclosed the vi if you want to take a look.
Thanks for your time,
Attachments:
cn8202temp_controller.vi ‏605 KB

Hey Jordan,
Thanks for responding. The recipe I am using is start from room temperature (20ºC), ramp up to 100 ºC over a period of 15 minutes, remain there for 10 minutes, and then ramp up to 1200ºC over a period of 110 minutes, remain for 10 minutes, then ramp down to 20ºC over a period of 280 minutes. I ran through all the string codes in the program and the only two I can't validate is Run Recipe string $0101W065.0000G2 and the cancel recipe string $0101W063.0000G0
I called and sent emails to Omega on this issue and their response is that they don’t do third party programming. I was hoping that by posting it on here that someone may have used the program and could confirm if it works or not and if it didn’t work could possible tell me what needs to be changed. I’m really beating my head against the wall here and use help from anyone.
Thanks again.
Kevin

Has anyone got PPTP VPN to work on Lion Server?

Has anyone got PPTP VPN to work on Lion Server?
I had a go with the terminal commnds posted by apple support but no joy. Since then Apple has pulled the suport article - is it because it didn't work?
I get PPTP is less secure but PPTP seems to be more reliable don't know whey they can't keep as GUI. I've got them both running on our 10.4 server and L2TP stoped allowing connections for no reason PPTP was still working L2TP started working again on its own. Plus L2TP drops my connection when I connect with a 2nd device e.g connected with my Macbook connect with my iPhone (different username) it drops my Macbook.
Any advice getting PPTP to work on Lion Server would be appreciated
Thanks
Ben

Hi,
I have posted a bugreport on this issue to Apple. Currently (10.7.2) it is not possible to run PPTP on any Mac OS X Server when using a 10.7 Server as Directory Server.
I have tried 'everything', but the MPPE encryption mechanism seems to be broken.
Edit: I see now that the bugreport is filed as a duplicate to an older case, which is now closed. I hope this means they have found the problem and will release a fix in the next update.

Anyone got Nokia Music to work with (recognise) N9...

Several times over the last months I have tried to get Nokia Music to work with my N95 8GB.
Every time I have spent hours and hours installing, upgrading, uninstalling etc etc but never success.
The Nokia Music PC software will not recognize my phone.
No matter what kind of connection i choose when i connect the phone - PCSuite, Mediaplayer etc, none of them makes the Nokia Music recognise the phone.
I am currently running Windows XP SP3, PC-suite 7.1.30.9, Nokia Music 1.3.20716.09, phone firmware is 31.0.015, phone code is 0550372
I am (_again_) dead tired of this, and for the moment (again) I truely hate Nokia PC software.
Has anyone got Nokia Music to work with N95 8GB?
Regards,
Njål
Solved!
Go to Solution.

Hi Njaale
Yes - it is working fine for me on a n95-
You need to connect your n95 in Media player mode.
You have 1.3.20716.09 but the latest version is - 1.3.2072
1) You can get the latest version from here - http://musicstore.nokia.com/download.aspx
2) If you are having licencing issue it could be because of the drm folder . If step one does not work try to delete the drm folder - C:\Documents and Settings\All Users\DRM . You need to make sure that hidden files and folders are not hidden and also that protected operating system files are not hidden.
To see hidden files:
1.
On the Tools menu in Windows Explorer, click Folder Options.
2.
Click the View tab.
3.
Under Hidden files and folders, click Show hidden files and folders.
Oh and just to be sure you are using nokia music
Here is a picture of it - http://www.slashphone.com/media/data/766/nokia_music.jpg
You can see in that picture on the left hand side is the phone you drag and drop your music into that phone picture to transfer your music.
Nokia pc suite below does not transfer nokia music
picutre - http://tltc.shu.edu/mobile/Nokia-PC-Suite_1.png
This is because the software in the first link (nokia music) is designed to recognise "DRM" software. But nokia PC suite in the second link does not currently do that.

Has anyone got OA Framework Tutorial working on R12 Jdev 10g?

I have successfully got the tutorial for OA Framework working on my Apps 11.5.10 install with very few problems.
I now have Apps R12 installed and have downloaded the correct Jdev 10g with OA Framework patch, but I am hitting some a number of errors. I can see that the tutorial code and documentation is the same as Jdev 9i, and has not been updated. Taking this in to account I am adapting the tutorial to the Jdev 10g, but I am hitting deployment problems in the local OC4J container, where AppsLogin is being requested and not found.
I therefore wonder whether anyone out there has got the tutorial to work in Jdev 10g?
I'm happy to try and figure it out for myself, but I would prefer to know that it is relatively straight forward to do.

Yes I'm getting the following error message:
oracle.apps.fnd.framework.OAException: Application: FND, Message Name: SECURITY_APPL_LOGIN_FAILED.
I have seen this elsewhere on the forum but they all relate to Jdev 9 on 11.5.10. I wanted to know whether anyone else had got OA framework tutorial working on R12 because then I know from that one fact whether it is possible on the code that Oracle has released; any problems I encounter are then likely to be setup/installation/config issues that I should be able to resolve myself.
I'm surprised that no one has yet just given me a 'yes' given the number of experienced developers on the forum.
BTW, the full stack trace is:
oracle.apps.fnd.framework.OAException: Application: FND, Message Name: SECURITY_APPL_LOGIN_FAILED. at oracle.apps.fnd.framework.server.OAExceptionUtils.processAOLJErrorStack(Unknown Source) at oracle.apps.fnd.framework.OACommonUtils.processAOLJErrorStack(Unknown Source) at oracle.apps.fnd.framework.CreateIcxSession.getEncryptedSessId(Unknown Source) at oracle.apps.fnd.framework.CreateIcxSession.createSession(Unknown Source) at runregion.jspService(_runregion.java:136) at com.orionserver.http.OrionHttpJspPage.service(OrionHttpJspPage.java:59) at oracle.jsp.runtimev2.JspPageTable.service(JspPageTable.java:453) at oracle.jsp.runtimev2.JspServlet.internalService(JspServlet.java:591) at oracle.jsp.runtimev2.JspServlet.service(JspServlet.java:515) at javax.servlet.http.HttpServlet.service(HttpServlet.java:856) at com.evermind.server.http.ServletRequestDispatcher.invoke(ServletRequestDispatcher.java:711) at com.evermind.server.http.ServletRequestDispatcher.forwardInternal(ServletRequestDispatcher.java:368) at com.evermind.server.http.HttpRequestHandler.doProcessRequest(HttpRequestHandler.java:866) at com.evermind.server.http.HttpRequestHandler.processRequest(HttpRequestHandler.java:448) at com.evermind.server.http.HttpRequestHandler.serveOneRequest(HttpRequestHandler.java:216) at com.evermind.server.http.HttpRequestHandler.run(HttpRequestHandler.java:117) at com.evermind.server.http.HttpRequestHandler.run(HttpRequestHandler.java:110) at oracle.oc4j.network.ServerSocketReadHandler$SafeRunnable.run(ServerSocketReadHandler.java:260) at oracle.oc4j.network.ServerSocketAcceptHandler.procClientSocket(ServerSocketAcceptHandler.java:239) at oracle.oc4j.network.ServerSocketAcceptHandler.access$700(ServerSocketAcceptHandler.java:34) at oracle.oc4j.network.ServerSocketAcceptHandler$AcceptHandlerHorse.run(ServerSocketAcceptHandler.java:880) at com.evermind.util.ReleasableResourcePooledExecutor$MyWorker.run(ReleasableResourcePooledExecutor.java:298) at java.lang.Thread.run(Thread.java:595)
Cheers
Andy

Has anyone got the B500 to work with Ubuntu? (nvidia driver problems)

In two weeks, I have been completely unable to get the nvidia driver working with the B500 on Linux. No matter what I try to do, the X server doesn't start, and my /var/log/Xorg.0.log file ends with "fatal server error: no screens found." I have tried feeding a custom modeline to xorg.conf, explicitly calling an EDID file which I extracted from the Windows installation, using the upstream nvidia driver installer, using the official repository driver, and probably a bunch of other stuff that I'm not recalling right now.
Versions I've tried this on:
Kubuntu 10.04, 32- and 64-bit
Ubuntu 10.04, 32-bit
Kubuntu 9.10, 32-and 64-bit
I am stumped. Has anyone successfully gotten this to work?
best,
-p.
Solved!
Go to Solution.

Solved with the kind assistance of paulricardomc on the Ubuntu Forums: http://ubuntuforums.org/showthread.php?t=1477507
Short version of the fix:
1. Extract the edid from the Windows partition using softMCCS, saving as edid.bin
2. Save the edid.bin file in /etc/X11 (or wherever you like)
3. Include the following in the device section of your xorg.conf:
"Option" "ConnectedMonitor" "DFP-0"
"Option" "CustomEDID" "DFP-0:/etc/X11/edid.bin"
Fire up X and you're good to go.

Anyone got 5.1 surround working for games in OSX or Windows 7 on 2010 Mac P

I got mine earlier this month have been trying out games in bootcamp on windows 7 they work really well with amazing graphics but no 5.1 sound in either OSX or W7, through the onboard sound card. Has anyone managed to to do this. I have only tried via optical. I can not yet devise a way to get 5.1 from the ATI 5770 MDP has anyone tried this?

1. Run Windows Update like you would on any other PC.
2. Windows is Windows no matter how it's installed so it's susceptable to the same viruses you could get by running it on any other PC.
3. Both Parallels and Fusion can boot from an installation of Boot Camp. you don't nee to install Windows twice.

Has anyone got BTCONNET (POP) mail working?

I already posted this in the touch forum, but after doing a bit of searching, realised that there is a specific forum for 'mail' under the iPhone section, so I am posting it here instead.
I have had my Touch for just over a week and all is well, except MAIL. I just can't get it to work with my BTCONNECT (POP) account..
I managed to get OUTGOING mails working.. But incoming is not working.. I get an error saying that it can't connect to my SMTP address. I have read a ton of posts from Google and tried everything, but its still not working...
My outgoing address is "smtp.btconnect.com", but I found a page from Apple themselves say that it should be "smtp.o2.co.uk", but this doesn't work.. To be honest, I don't see why it would, as this is a Touch not an iPhone (but the doc says that its for both), but I tried it never the less.
I did find one post from someone who had this problem and used iTunes to 'sync' his mail account.. I hoped this would work, but when i tried, nothing happened.. I even deleted my account from the Touch, selected my Outlook account under iTunes and did Sync. Whilst iTunes says its done it.. Nothing happens.
I should point out that for this test, I am at home, using the same connection that my Laptop (Which is able to send/recieve mail) is on.
I am starting to think I am wasting my time and just wondered if anyone in the UK has sucessfully got BTCONNECT mail working?
My fingers are crossed that someone can help
Jon

Just a note to everyone to thank you for your help and let you know that I cracked it. I figured I should post, incase anyone comes looking for a solution (I just wished I had not spelt BTCONNECT, BTCONNET in the title).
I stumbled upon a post on another forum from a guy who claims to have it working and has helped others.. I got in contact with him and he has shown me what he has done. It looks like there is a quirk (I would call it a bug) in the way that the iPhone/Touch handles SMTP.
It turns out that for BTCONNECT (And I suspect others) to work, you need OTHER SMTP servers in the list.. Even if they are not right.. withouth them, it simply doens't work.. But as soon as you add 2 'others' it just magically works.
The best way to get BTCONNECT mail working is like this:
1. Disable Wifi
2. Delete existing accounts
3. Add new 'Other' account
4. Enter the following (Using a made up name as an example):
Name: Your Name
Address: [email protected]
Password: <Your Password>
5. Save
6. Select 'POP'
7. Add Incoming Server Details:
Host Name: pop3.btconnect.com
User Name: john.smith
Password: <Your Password>
8. Add Outgoing Server Details
Host Name: smtp.btconnect.com
User Name: Leave Optional
User Name: Leave Optional
9. Save
Now at this point, it goes off to verify SMTP info and will fail (not only becuase WiFi is off, but it fails even if Wifi is ON). You now get asked whether you want to try turning SSL on.. If you hit NO, it goes off and tries again and never finishes.. If you say YES it ends with an error.. But alteast you can save it.
The point is, just say YES and then you will get a option to Save.
10. Now you have saved, go back into your mail config and select the Primary Outgoing Server.. Here you want to change/verify:
SSL = OFF
Authenitication: Password
Port = 25
11. At this point it should work.. And I got here on my own many times and it doesn't.. What you need to do is adds some 'other SMTP servers'.
I was given the advice to add "mail.btinternet.com", but my conclusion is that it doens't matter... On mine, I now have 2 "other" addresses (both pointing to SMTP.BTCONNECT.COM).. If I go into them, they are wrong, as SSL = ON and worse, they are grey so I can't change them or delete them.
I got it in this state after a lot of playing, and I know its not right, but since mine is working, I am not changing it.
This is the area you want to focus on.. You need to get 1 x Primary Server (SMTP.BTCONNECT.COM) and 2 x 'other' Servers (Point them to SMTP.BTINTERNET.COM if you like).
I don't know why.. I don't know how but this works!!
If I write a mail and send it, it goes instantly.. So you know that its working straight away..
Oh yes.. Turn WiFi on NOW, before you test.. I forgot at one point and almost gave up again...
I know this sounds stupid and you would think that it doesn't make any difference, but it does.. Not only did this work for me, but its also worked for several other people I know who also had problems getting SMTP working.
Good luck and I hope this helps someone
Jon
Message was edited by: jweaver100

Has anyone got BTCONNECT (POP) mail working on their Touch?

I have had my Touch for just over a week and all is well, except MAIL. I just can't get it to work with my BTCONNECT (POP) account..
I managed to get OUTGOING mails working.. But incoming is not working.. I get an error saying that it can't connect to my SMTP address. I have read a ton of posts from Google and tried everything, but its still not working...
My outgoing address is "smtp.btconnect.com", but I found a page from Apple themselves say that it should be "smtp.o2.co.uk", but this doesn't work.. To be honest, I don't see why it would, as this is a Touch not an iPhone (but the doc says that its for both), but I tried it never the less.
I did find one post from someone who had this problem and used iTunes to 'sync' his mail account.. I hoped this would work, but when i tried, nothing happened.. I even deleted my account from the Touch, selected my Outlook account under iTunes and did Sync. Whilst iTunes says its done it.. Nothing happens.
I should point out that for this test, I am at home, using the same connection that my Laptop (Which is able to send/recieve mail) is on.
I am starting to think I am wasting my time and just wondered if anyone in the UK has sucessfully got BTCONNECT mail working?
My fingers are crossed that someone can help
Jon

Just for continuity and incase anyone else has this problem, I have posted a solution here:
http://discussions.apple.com/messageview.jspa?messageID=9405022&stqc=true

Has anyone got mental ray to work on qmaster?

I keep getting segment failed messages on some machines when i render mental ray it spends about half an hour rendering two tga frames which are only 4k and can't be opened, if i lower the resolution and set it only to do 10 frames it works, its got me flumuxed does anyone know is mental ray satellite any better. It works fine incidently if i render with software renderer. Incidently i know you have to put -r rm in the settings. but any ideas would be appreciated

ok got it to work easiest way is to make sure the shared drive is mounted on all machines and put all files i.e textures and mb file on there too and in the qmaster make sure you specify the working directory as the shared drive as well as the project directory

Has anyone got gma3650 or gma3600 working?

Hi,
I'm currently considering buying this netbook:
http://www.johnlewis.com/231577593/Product.aspx
It has the dreaded gma3650 chipset, which seems to cause lots of issues. I have found this on the wiki:
https://wiki.archlinux.org/index.php/Intel_gma3600
Just wanted to see if anyone else has got this working before I splash the cash.
Many thanks in advance.

My advice... stay away. Far away. Fbdev doesn't give you any acceleration whatsoever. There's the emgd driver, but if you'll get that one to work is a very big *if*.

Has anyone got Push mail to work after migration t...

Has anybody sucessfully got Push mail working after migration from BT Yahoo mail to the new BT Mail server?
I'm still on the old BT Yahoo mail server and Push mail works fine on my iPhone
But people have told me that once migrated to the new BT Mail server, Push mail isn't available
BT tell me that it is, but there's a couple postings on the web saying Push mail won't work
So, my question is, is there somebody out there who who has been migrated to the new BT Mail server and who can confirm they can still get their @btinternet.com address post-migration to work as Push mail on their iPhone or ipad devices?

There is no push mail on BTMail. Once you have been migrated to BTMail you will need to have your devices fetch emails. There is apparently no plans to change this.

SECOND QUESTION - HAS ANYONE GOT ELEMENTS EDITOR NOT WORKING - ON WINDOWS 8.1?

I Get message - when i try to open elements 12 editor... a problem caused program to stop working correctly. Windows will close program and notify if a solution is available -- no response after 2 weeks - anyone help please? john reid

Microsoft advises that version 7 of PSE will work with Windows 8. The best option is a new computer with W8 and then do a clean install of Elements. Some difficulties may arise if upgrading the operating system on top of existing software. In those circumstances make sure you have your original disks or your download package, in case a re-install is necessary.
Microsoft Windows 8 compatibility.

Has anyone got BT broadband talk working with a 3r...

I would like some assistance if possible? i use an AVM Fritz Box 7270 and subscribe to BT broadband with calls. I currently dont use the BB talk as i have never got it working. Is it possible? how on earth do i get it working?
An idiots guide to getting this working would be preferable!!
Many thanks..

Guides are here:
http://www.jarviser.co.uk/jarviser/repeaterhubphone.html
Hope this helps(?)

Anyone got the SimpleCertAuthenticator example working with 5.1??

The SimpleCertAuthenticator example that does the client certificate to user
mapping doesn't seem to work. I followed the instructions and tried many
times
without luck. Any comments? Like where to look for error messages? Thanks.
Honbo

I got the example working on wls 5.1 using sp8 both in Linux and NT.
Try to print something in the SimpleCertAuthenticator constructor, because the
SimpleCertAuthenticator is instantiated during startup, be sure that you can see
the startup so that you can verify if the handle has ben installed correctly.
"Jayesh Patel" <[email protected]> wrote:
It also not working for me.
I have tried using both 6.0 sp1 as well as 5.1 sp8 .
Let me decribe what I did and let me know if I am missing any thing -Thanks
1) Installed personal certificate(from verisign)
3) Enforced client cert in console
2) exported CA file and pointed in clientRootCa
3) created user with emailId in cert
4) set cet authnticator to examples.security.cert.SimpleCertAuthenticator
5) Restarted server
6) invoked one servlet using https , browser propmpted for certificate,
but
thereafter it
says page can not be displayed. Unfortunately I don't have error
mesage
to know what
went wrong? I tested with same request with not ssl connection it
works.
i also put
systme.out.println in SimpleCertAuthenticator and it fails before
it.
"Peter S. Wong" <[email protected]> wrote in message
news:[email protected]..
Have you tried using it with the jaas example?
It works with that example in 6.0sp1.
Peter S. Wong
Honbo Zhou wrote:
The SimpleCertAuthenticator example that does the client certificate
to
user
mapping doesn't seem to work. I followed the instructions and triedmany
times
without luck. Any comments? Like where to look for error messages?Thanks.
Honbo

Anyone got a crucial SSD working MBP 17?

Similar Messages

Maybe you are looking for