Anyone have any suggestions on how to find an iPod touch when it's location is off?

Anyone have any suggestions on how to find an iPod ouch when it's location is turned off?

Unfortunatley, with location turned off it is impossible to locate it. Also if your IPod is dead or is not connected to wifi it will not give its location.
My best reccomondation is refering to this link: http://support.apple.com/kb/ht2526
Good Luck!
Sorry I can't give you anything better!

Similar Messages

  • Anyone have a syggestion on how to get my Ipod touch working again besides putting it into restore mode

    Anyone have any ideas on how to get an Ipod touch to charge or sync without putting it into restore mode, I've prettymuch tried everything thats been put online so far

    Tried DFU mode?
    To do this follow these instructions:
        1. First, Open up iTunes, plug in your iPod Touch/iPhone to the Computer's USB port. Turn on your Computer's speaker and make sure it is loud enough that you can hear it.
        2. Hold down the Home button (top left for iPod Touch and top right for the iPhone with the screen facing you) and the Power button (located on the front bottom of your iPod Touch/iPhone) simutaneously, until the screen goes black and the device turns off. (past the red slider/slide to power off screen)
        3. Now let go of the Power button, but continue to hold the Home button. Your iPod Touch/iPhone should have turned off and the screen should not be on.
        4. After around ~10-20 seconds, you will hear a noise (beep/ding) from your Computer as if it had just recognized a new hardware device, now iTunes should recognize it in DFU mode.
        5. After iTunes recognizes the iPod Touch/iPhone, let go of the Home button otherwise it will go into recovery mode and you will have to do the entire DFU process over again.
        6. You will know when you have put your iPod Touch/iPhone correctly into DFU mode when the display is blank and that you do not have anything on your device.
    Once you have done this click restore and iTunes sould start to dowbnload and install the latest firmware.
    #Please note this will reset your iDevice to factory settings
    Syther101

  • My video app that is preloaded on the IPAD will not open. all I can see is a blank screen. Does anyone have any suggestions on how I can fix it?

    My video app that is preloaded on the IPAD will not open. all I can see is a blank screen. Does anyone have any suggestions on how I can fix it?

    The "The connection was reset" error message can be caused by a bug fix for the BEAST (Browser Exploit Against SSL/TLS) attack that the server doesn't handle.
    *[[/questions/918127]]
    *[[/questions/918028]]

  • Can't synch iphone. Get message "synch server failed to synch the iphone.  ANyone have any suggestions on how to fix this issue?

    Can't synch iphone. Get message "synch server failed to synch the iphone.  Anyone have any suggestions on how to fix this issue?
    Windows 7
    ios 7.1
    iphone 5

    Hello, skifmli
    Thank you for visiting Apple Support Communities.  
    I understand that you are unable to sync your iPhone and receive an error.  I was start with restarting iTunes and your computer.  Once this is done, test the results by attempting a sync.  If the issue persists, go through the troubleshooting steps in the article below.  
    Troubleshooting Sync Services on Windows with Microsoft Outlook 2003, Outlook 2007, or Outlook 2010
    Cheers, 
    Jason H.  

  • My question has to do with analog input and triggering? Does anyone have any suggestions on how i can improve the attached vi so it can trigger on a 50kHz ten cycles pulse after the pulse has been sent out on the output?

    Could you just look at this vi and tell me if i am doing anything wrong? I get errors that are different each time I change something. here are the inputs I am using
    Output Side:
    amplitude = 1
    freuency = 50kHz
    Sampling Frequency = 1MHz
    3 of Samples = 200
    Input Side:
    Input Buffer 4000
    trigger type = analog
    pretrigger = 5
    edge or slope = rising
    scan rate = 500kHz
    # of scans = 2000
    Conditional Retrieval
    mode = on
    slope = rising
    skip count = 0
    level = .1
    offset = 0
    hysteresis = 0
    So what we want to do is capture the ten
    cycles of the 50k output pulse on the input and need to store that so we can plot it later, do you have any suggestions. we are using the PCI-MIO- 16E board.
    Thanks,
    Jarrod
    Attachments:
    InputOutput2.vi ‏88 KB

    1) Toss the sequence frames (no flames please).
    2) Set you read and have it ready to trigger before oing the output.
    3) After the output, go back and read the data that is waiting for you.
    4) If you have errors tell us what they are and under what conditions they occured.
    End of Ben's suggestions for now.
    Ben
    Ben Rayner
    I am currently active on.. MainStream Preppers
    Rayner's Ridge is under construction

  • HT1665 my iphone headphones remote has stopped working after a few uses. does anyone have any suggestions on how to fix it please??....

    Hi all.
    My headphones are new form apple as they came with the phone. They have been good for the few times i have used them but out of the blue after about a weeks use they have stopped allowing me to skip forwrd or backwards???????? I am still able to pause and use my mic for Siri so im a little bit confused as to what the problem can be.. Is there anyone out there who knows what the problem might be or how to fix it??
    Thanks.

    Go to the settings in your Jeep, "forget" the iPhone. And on the iPhone "forget" the jeep. Then put the Jeep in Pairing Mode and tap Settings/BlueTooth on the phone and pair them anew (which sounds less confusing than "repair them").

  • As of 2 months ago, I cannot fully access Facebook using either Safari or Firefox browsers. I have a Mac G5 running OSX 10.5.8, Safari 5.0.6 and Firefox 3.6.28. Does anyone have any sugesstions on how I can resolve this?

    As of 2 months ago, I cannot fully access Facebook using either Safari or Firefox browsers. I have a Mac G5 running OSX 10.5.8, Safari 5.0.6 and Firefox 3.6.28. Does anyone have any suggestions on how I can resolve this?

    Aha, a PPC Mac!
    The last really supported Flash for PPC was 10.1.102.64, but if it's for like Facebook or such, people have been fooling FB to think they have a later version installed.
    Texas Mac Man's Flash hack/post...
    https://discussions.apple.com/thread/3599648?tstart=0
    Flash player 11.1 hack on PowerPC - https://discussions.apple.com/message/16990862
    See in each Browser which version of Flash it thinks it has...
    http://kb2.adobe.com/cps/155/tn_15507.html

  • I have a samsung scx 4100 series and i just updated to mountain lion and now i keep getting a "filter failed" error, anyone have any suggestions as to how to fix it.

    I have a samsung scx 4100 series and i just updated to mountain lion and now i keep getting a "filter failed" error, anyone have any suggestions as to how to fix it.

    Hi again, when you clicked on Mountain Lion and Lion in the App Store you are telling the laptop to reinstall them both.
    You may have allowed simutanious downloads checked at the bottom of the window, I don't know, but I expect Mountain Lion is downloading, so Lion is waiting for it to finish, so if you have Mountain Lion installed cancel both download's.
    Cancell both downloads anyway.
    Go to the apple logo , top left, click on it, then click on about this mac, a window will open telling you what's installed,  Mountain Lion is OX 10 version 10.8.2 click on more info, to find out more, Lion will be OX10 version 10.7.4.
    Only update were it say's check for updates, not download now.

  • I can't open any attachments on gmail, does anyone have any suggestions as to how to fix?

    I can't seem to open up any attachments in gmail.   Does anyone have any suggestions as to how to fix?   Thank you

    Hello Jim,
    Thank you for providing the details of the issue you are experiencing with opening attachments in Mail on your iPad.
    I recommend following these steps for an issue like this (you can skip 4 because it does not relate to the issue you are experiencing and any other steps you may have taken):
    If a single application is not responding or stops responding when it opens, you can force it to close.
    If the device is unresponsive or if certain controls aren't working as expected, restart your device.
    If the device remains unresponsive or does not turn on (or power on),reset your device.
    If there is no video or if the screen remains black, verify that the device has enough charge to turn on:
    If you are using an iPad, ensure that it's connected to the USB Power Adapter supplied with the device.
    Let charge for at least twenty minutes, then see if it starts normally.
    If there is no image on the screen, press the Sleep/Wake button to attempt to wake the device.
    If the screen displays a red battery icon, continue charging the device until the battery is fully charged.
    If the above steps do not resolve the issue, or the if the screen remains black or shows a persistent Apple logo, try restoring with iTunes:
    Connect the device to your computer and open iTunes.
    If the device appears in iTunes, select and click Restore on the Summary pane. Learn more about restoring iOS software.
    If the device doesn't appear in iTunes, try to force the device into recovery mode, and then restore it.
    If the above steps do not resolve the issue, contact Apple.
    You can find the full article here:
    iOS: Not responding or does not turn on
    http://support.apple.com/kb/TS3281
    If you get to step 5, I recommend backing up your iPad before performing the restore:
    iOS: Back up and restore your iOS device with iCloud or iTunes
    http://support.apple.com/kb/HT1766
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • When I open Safari, it just hangs up. I cant get to the menu to reset and i cannot find the apple.safari.plist folder in the preferences folder. Anyone have any suggestion?

    When I open Safari, it just hangs up. I cant get to the menu to reset and i cannot find the apple.safari.plist folder in the preferences folder. Anyone have any suggestion?

    Alright, I figured it out. I found the Preferences.plist in the ~/Library/Preferences/SystemConfiguration folder. I deleted it and restarted my macbook. Now Safari works!

  • My iworks is not working?? Does it anyone have any suggestions as to how to fix the problem?

    It won't let me open my numbers, pages or keynote. Does anyone have any suggestions as to how i can fix the problem?

    I am having the same issue. And today, I noticed that when I was talking on the phone, the volume went down low. I had to reboot the phone, so that the volume was up again. Mostly, though, it's my music that I am having issues with.
    Same issue as listed above. iPhone 4S. IOS6.

  • My iPhone 4S has decide to stop playing any of my music. All my songs are there, but when I click to play, it just scrolls through a bunch of songs and then reverts back to the play list. Anyone have any suggestions as to how to correct this? Thanks.

    My iPhone 4S has decide to stop playing any of my music. All my songs are there, but when I click to play, it just scrolls through a bunch of songs and then reverts back to the play list. Anyone have any suggestions as to how to correct this? Thanks.

    I am having the same issue. And today, I noticed that when I was talking on the phone, the volume went down low. I had to reboot the phone, so that the volume was up again. Mostly, though, it's my music that I am having issues with.
    Same issue as listed above. iPhone 4S. IOS6.

  • I keep on getting I need to install the JRE for Yosemite.  I installed it but it still says I need to install it. Does anyone have any suggestions?

    I installed the newest JRE Like it said and I still get the same thing...Anyone have any suggestions?

    '''''"When I try to uninstall it to reinstall it, it constantly tells me that the F/fox program is still open and it can't uninstall it."'''''
    Must be the "hang at exit" problem. You already know how to do Step1; now just determine which Add-on (Extension or Plugin) is causing the problem.<br /><br />
    #Stop the Firefox process:
    #*[http://kb.mozillazine.org/Kill_application Mozillazine - Kill application]
    #*Windows 7 users click [http://www.techrepublic.com/blog/window-on-windows/reap-the-benefits-of-windows-7s-task-manager/2576 here]
    #Why Firefox may hang:
    #*[http://support.mozilla.com/en-US/kb/Firefox+hangs Firefox hangs] (see Hang at exit)
    #*[http://kb.mozillazine.org/Firefox_hangs Firefox hangs (Mozillazine)] (see Hang at exit and Closing Firefox properly)
    #*[https://support.mozilla.com/en-US/kb/Firefox+is+already+running+but+is+not+responding Firefox is already running but is not responding]
    #Use Firefox Safe Mode to find a problem with an Extension or Plugin:
    #*Don't check anything when entering Safe Mode, just continue
    #*If the problem does not occur in Safe Mode it is probably and Extension or Plugin causing the problem
    #*See:
    #**[[Safe Mode]] and [http://kb.mozillazine.org/Safe_Mode Safe Mode (Mozillazine)]
    #**[http://support.mozilla.com/en-US/kb/Troubleshooting+extensions+and+themes Troubleshooting extensions and themes]
    #**[http://support.mozilla.com/en-US/kb/Troubleshooting+plugins Troubleshooting plugins]
    #**[http://support.mozilla.com/en-US/kb/Basic+Troubleshooting Basic Troubleshooting]
    '''''"When F/Fox opens the page is blank."'''''
    See [http://support.mozilla.com/en-US/kb/How+to+set+the+home+page How to set the home page]
    '''If this reply solves your problem, please click "Solved It" next to this reply when <u>signed-in</u> to the forum.'''

  • Anyone have any ideas of how to make the battery on the iphone5 last longer?

    Anyone have any ideas of how to make the battery on the iphone5 last longer? I don't use the phone that much and the battery does not last all day. Phone is new.

    Many suggestions can be found here
    1. turn off push email and use fetch or manual fetch instead.
    2. turn off or at least limit notifications
    3. limit use of apps that use location services (eg. maps app - heavy power useage when running).
    4. in General->About->Diagnostics & Usage, turn off Automatic sending.
    5. Privacy->Location Services->System Services, disable everything (none of it need be running for normal use).
    6. Wifi, turn off "Ask to Join Networks" so your device is not polling all open networks it finds.
    7. keep brightness as low as you can get by with.
    Finally, get a car charger, and a second charger for work/school and just plug in whenever it is convenient to do so.
    Or, if it suits your daily routine better, get an external battery power brick or case and charge it periodically from that.

  • I am trying to connect my Macbook pro 2010 to my Samsung HDTV using a mini display port to hdtv cable. Trying to play a slide show in IPhoto but I only get sound with no picture. Does anyone have any suggestions?

    I am trying to connect my Macbook pro 2010 to my Samsung HDTV using a mini display port to hdtv cable. Trying to play a slide show in IPhoto but I only get sound with no picture. Does anyone have any suggestions?

    I keep saying this over and over, in the hope that people who do a search will find it.  Apple cannot possibly test for or be reponsible for the bazillion combinations of adapter, cables, and TV's out there.  The only monitors that are 100% guaranteed to work with the MacBook Pro are the Cinema Displays and Thunderbolt Displays, because, they're made by Apple.  They're expensive, but they work perfectly.
    My guess is that you bought a cheap MDP to HDMI cable, or have a defective one.  From my reading of these boards over the past few months, cheap cables have a high failure rate.  And the regular priced ones have only a slightly less of one.  Try a new one.  Make sure you do not damage the Thunderbolt port.

Maybe you are looking for