Anyone using HDTV Component Video on an MSI 6600GT?

I am building a system for somone and want to use a 6600GT because of the component video output. I have a 6600GT already but I have no HDTV to test the component output. Has anyone used the component output on a HDTV, and how well did it work?
Thanks

Basically the product and its drivers are junk.
I tried it in another computer and the picture was clean , until the whole thing locks up after 3 seconds.
Did the fixes they said might work, ng.
Good luck to anyone using this crap.

Similar Messages

Anyone using asus silent knight II on msi DKA 790GX platinum?

hihi..
anyone using asus silent knight II on msi DKA 790GX platinum?
anyway to orient the air flow to horizontal setting. cos right now my cpu cooler was shooting up warm air to my power supply.
thanks

Quote from: nel_hawk on 22-May-09, 08:23:49
Oh I see.. now then know that it's ATX standard. thanks.
then how about the rear fan, is it functioning the same as PSU fan?
or is the rear fan's function is to suck out the whole system's warm air?
It's to help getting hot air out, but that is added by case builders.
Here you have the original specs: http://www.formfactors.org/developer%5Cspecs%5Catx2_2.pdf
Case builders added extra fans because ATX standards aren't good enough for high-end systems.
However, ATX is designed to let the PSU suck out the hotair...
Anything you add to it makes it all cooler and doesn't hurt.
You should know that AMD CPU's do not get very hot at all, it's the Intels that do, especial the Pentium4, so case builders created all sorts of solutions to cool them down as ATX wasn't sufficient for the P4.
Even Intel made a new spec BTX, but that wasn't accepted by builders.

Can i use both Component video and HDMI?

Hi guys,
Im wondering if its possible to connect both Component video and HDMI on the ATV?
Its currently connected to HDMI on our main HD TV, however, the apartment we have has a strange setup in which you must send RF signals to a loop back in the main room to reach all other TV's.
We dont have the capital for either another flatscreen TV or a second Apple TV until next year - so currently we've got an older (see 2004) bulk of a CRT TV upstairs and my thought was i could route a signal to the RF loop back from the ATV and use my iphone remote to control what it plays to view upstairs.
For this id need a component to composite/rf convertor which ive found so sending the signal is no problem, but what would happen if i were to connect component cables as well as the HDMI, does the ATV output on both, or priortise the HDMI?

When both types of cable are connected to the tv at the same time, the HDMI connection will be on by default but the component is turned off... and what happens if the source to the HDMI cable is off - eg its plugged in but its got no where to send the signal, would it still not send to the component?.. You mean if the tv was off, same thing, HDMI would take precedence.
Are you sure about this, Winston? I have only 2 component (and 2 HDMI) inputs on my Panasonic HDTV. For this reason I invested in an Audio Authority Component Switcher (Model 1154A) a few years ago. When the TV device arrived I connected it directly to the HDTV via my HDMI-2 HDTV input and also connected the component video and optical audio to the switcher. I have no problem using the HDTV's input selector to switch back and forth between component and HDMI lines. While I admit I cannot split the screen between an HDMI input and anything else for simultaneous viewing, I can leave both lines plugged in and switch between the two lines. In addition, the activity light on the switcher indicates there is a signal present on the switcher even when I am watching the HDMI line. (Of course, this may simply be triggered by the switcher's optical audio signal since I normally watch the TV video via the HDMI line (with HDMI audio muted) and use the optical audio line to drive my receiver's AC3 decoder so I can enjoy 5.1 audio with my latest conversions.) Am, therefore, wondering if the OP may have the same capability and could then simply switch to a different input mode to "de-negotiate" his HDMI connection and allow access to whatever component device he needs as long as he doesn't need simultaneous viewing on both TVs.

How to SET or Configure BIOS to use XFX6200 TC video card for MSI K8N NEO4 Plat.

Hello Friends,
Can any body help me to the following problem?
I am having XFX 6200 TC Geforce / nvidia Grafix card for my MSI K8N NEO4 Platinum Ultra board.
The BIOS states PCIE clock speed as 100 Mhz as default. The setting can be changed upto 145Mhz.
My Video card can be configured upto 350 Mhz. How to do this and which is the right way to use the display card with optimum setting?
Thanks for all those who reply to this.

the coolbits link http://downloads.guru3d.com/download.php?det=815
to manually set the clocks on the graphic card, after installing coolbits, just follow the instruction on that page:
Quote
Unpack the achive (self extracting) and then in the setup directory simply click on the .reg file. To get to these options simply right-click on your desktop and go to 'NVIDIA Analog Display' (Win XP/2003). For Win 2000 and lower you may need to get to the Nvidia Control Panel the old way. Right click desktop > Properties > Settings > Advanced > GeForce xxxx
for overclocking just take a look at the overclocking sections of the forum. make sure to read the stickies before you do anything.

Hauppauge ImpactVCB Video Capture Board - Anyone use it?

Has anyone used Hauppauge ImpactVCB Video Capture Board with Flash Media Live encoder and have success?

George. You probably don't have many options with the Epix board. However, if your Epix software enables you to save files to disk, then you can open them from LabVIEW and process them with Vision or Vision Builder.
Another option is to contact Graftek (www.graftek.com) or ImageMill (www.imagemill-tech.com). They have created drivers for third party image acquisition boards in the past and they may have one for your Epix board.
A third option, of course, is to upgrade your Epix board to an NI IMAQ board. Your sales contact within NI may even be able to give you a discount on the trade in, but I can't guarantee it.
Good luck!
Kyle V

Intel iMac Component Video Out

Has anyone tried a component video out connection to an HDTV from the Intel iMac? I've read from the ATI website that the new Radeon X1600 card supports component video out with an adapter.
There was never a really good way to do this with previous Mac models.

A little more news about component out from the Intel iMac 20"
The VGA adapter included with my 12" iBook does not fit the mini-dvi port on the iMac. So you need to buy a new adapter from Apple.
Also:
I tried using a VGA-to-component cable with the iBook VGA adapter and a standard television set. The cable is designed to interface a component-out DVD player to a VGA-in BenQ projector. I ran the cable to the component-in jacks on my Sanyo (analog-non HD) television. No go. Tried several resolutions and adapter refresh rates, and got some smeared video, but it made me nervous and I stopped experimenting. Haven't tried this cable with my HDTV for fear of damage.
Basically, the cable was meant to take a video signal from the DVD player to the projector. My experiment was mac to TV.
So sad, oh so sad ;<
Regards,
Gene

No HDMI input for HD-TV; component video doesn't give picture

I just swapped an HD DVR STB, which was connected via component video, for an HD STB. There is no HDMI input on my HD ready TV, so I connected the STB to the TV via the same cables as the tech did when he came out (i.e., I used the component video and component audio connections). I get sound, but no video.
I tried the other connections: S-video gives me a black and white picture,
and the standard coax cable gives me regular video + audio.
I would prefer to use the component video, though. Is this a widespread problem? Is there a solution?
Solved!
Go to Solution.

I'd connect it using the component cables, and then contact tech support and see if they can do a factory reset on the STB. If that fails, they will likely replace it.
====================================================================================
Error exists between keyboard and chair.

Importing Analog Component Video

I'm using a Sony J-30 deck to import Beta SP and want to import at a higher quality than the Firewire out in the back. I was wondering if I could use the Component Video out instead? If so, what type of hardware do I need to convert to a digital signal? My hope is to be able to import as DVC50.

Thanks, I installed a Blackmagic HD extreme 2 and am having capture problems. I can control the deck from fcp, but no audio or video comes through. The only way I can import is by using capture now and the clip Import is all black with no audio. Have tried multiple import settings, but still no luck. Please shine some light on me.
Message was edited by: s80man9

How can I do live streaming with a Mac Book Pro 2011, using a new model of Sony HD camcorder which does not have firewire out/input? it comes only with a component video output, USB, HDMI and composite RCA output?

I need to do live streaming with a Mac Book Pro 2011, using a new model of Sony HD camcorder (http://store.sony.co...ber=HDRAX2000/H) ..this camcorder model does not have firewire out/input ..it comes only with a component video output, USB, HDMI and composite A/V video output..
I wonder how can I plug this camcorder to the firewire port of my laptop? Browsing on internet I found that Grass Valley Company produces this converter http://www.amazon.co...=A17MC6HOH9AVE6 ..but I am not sure -not even after checking the amazon reviews- if this device will send the video signal through firewire to my laptop, in order to live streaming properly? ..anyone in this forum could help me please?
Thanx

I can't broadcast with the built in iSight webcam... how would I zoom in or zoom out? or how would I pan? I've seem people doing it walking with their laptops but that's not an option for me... there's nothing wrong with my USB ports but that's neither an option to stream video because as far as I know through USB you can't connect video in apple operating systems ..you can for sure plug any video cam or photo camera through usb but as a drive to transfer data not as a live video camera... is by firewire an old interface developed by apple that you can connect all sorts of cameras to apple computers... unfortunately my new sony HDR-AX2000 camcorder doesn't have firewire output...
thanx

How to connect Apple TV (2g) HDMI to HDTV with only component video input.

Trying to connect Apple TV (2g) HDMI to HDTV with only component video input. Can I use a simple cable or do I need a converter box/plug? Is the HDMI signal coming from ATV encrypted or HDCP enabled?
The TV is HD, but only has a component input and not HDMI. Apple TV 2g only has HDMI output.

google component hdmi converter
but they are pretty expensive and may not work at all
and will not work with any DRM material as in movies you reant and maybe netflix and the sports thingy

Anyone using a HDMI to component cable?

Using an Apple TV 2
My TV doesn't have HDMI - I see cables for sale, but not at the Apple store. Anyone use one so I know it will work?
Thanks

Can anyone answer the original question - Are you doing this?
Yes, using the "converter" option. Or rather I can do this and have for test purposes but now have enough HDMI HDTVs in the home to not be forced to do this if I choose not to do so.
Have you tried and it didn't work?
As indicated above I tried it. Normally, the only time the converter I have won't currently work is if the target TV does not support 720p input. No one has yet mentioned the fact that unless you purchase a "broadcast level" device, these converters do not include any scaling capabilities. If your particular TV only supports 1080i component input, then even the converter will will not work because the component output is still at 720p as output by the TV2.
DId it work?
Once again, it did.

Using ipad 1& component video cable to view hulu on the tv

Bought component video cables from apple, hooked up to tv & ipad. No video from hulu. Any ideas? Have i exceeded the capability of this?

Hulu has only activated their TV out through HDMI on iPad 2.
Hulu has not activated TV out for component or composite cables on either iPad1 or iPad2.
I sent an email to Hulu about this issue.
The reason they gave me was that they are still trying to secure content rights to stream content to mobile devices that can stream content out of them to any video device.
So, unless you have an iPad 2 using Apple HDMI connector to one of the new HDTV sets through HDMI, your, currently, out of luck.
This may change, but do not know when.
It's frustrating because Apple TV put works fine with NetFlix.
I am a Hulu+ subscriber and feel like this should, already be a feature if I am paying customer.
Hulu, right is like all the video apps from the networks.
They just won't allow outputting the iPad video stream to your TV.
All of the broadcast network apps do not have TV out capability so you can watch the content streamed through the iPad to whatever TV you own.
It's frustrating and stubbornness on the the part of the major networks.
I do not know they are not including this functionality?
The still run commercials on these apps like regular network broadcasts.
They should all just enable the TV out functionality.
Our family stop using cable, I end up watching network news and shows on my 10" iPad screen instead of the signal being allowed to output through my iPads cable connector to my TV for viewing.
Ridiculous!

How to play recorded videos using FLVPlayback component?

Hey Guys,
     I recorded videos using fms and i want to play them using FLVPlayback component. I've done some research but i cant find something
useful, I tried this code :
     flvplayback.source = "rtmp://localhost/appname/instancename/video";
     this code is not working. Am i doing it wrong or something? Can anyone please point me on the right direction!
    Thanks in advance!
Randy

You may like to use this tutorial for your purpose:
http://en.wikibooks.org/wiki/Beginner's_Guide_to_Adobe_Flash/Video/Using_The_FLVPlayback_C omponent
Here, in the content path you need to put your URL, also make sure that the instance name exist and provide the FLV extension in the url.
Hope that will help you.

How can i use apple tv and iTunes movies with component video cables for an older receiver and projector?

i have an older yamaha receiver and projector both without hdmi inputs but component video instead. I would like to get apple tv and start renting movies through iTunes but apple tv only supports hdmi and ive read that iTunes has codes to prevent the use ot analog cables with movies. Is there a way to adapt hdmi to component video for both apple tv and iTunes easily?

Yes, HDMI is the only supported method. Also, with converters you will run into issues with HDCP (which will prevent you from streaming DRM content from iTunes etc) as well as resolution.

Anyone know which render format I should use, my film will be used on a video wall (12 screens) and I need super quality. My footage format is 1080p HD resolution 1920x1080. I will be running the project from a mac with a direct line to video wall. Thanks

Anyone know which render format I should use, my film will be used on a video wall (12 screens) and I need super quality. My footage format is 1080p HD resolution 1920x1080. I will be running the project from a mac with a direct line to video wall. Thanks in advance.

I do some VJ-type work, involving playback of QuickTime files from the computer to projections, and I get good results using ProRes 422. That's convenient, because ProRes 422 is such a great editing codec, too.
Traditionally, VJs use PhotoJPEG codec, which also works well, but it's a bad editing codec. So you would have to export an edited master, then convert.
If you want it to look as good as possible, definitely schedule some time to test the footage on the wall. You may want to change the color correction of your footage to match the projectors. And if you feed the video wall some flat gray, you can see if any of the projectors need to be adjusted.
I'm not sure what application you're using for playback, but QuickTime Player 7 works well. It has an option to play fullscreen on an external monitor (View > Present Movie…).

Anyone using HDTV Component Video on an MSI 6600GT?

Similar Messages

Maybe you are looking for