Anyone Using Via Raid0 And 1 Sata On Promise?

I'm using raid 0 on VIA and want to use a maxtor sata 80gb on Promise for files. When I boot it shows the maxtor in Promise but not in Windows. When I go to the drivers for Promise, it says CODE 10. I searched the posts for this but didn't find anything. Any help will be welcome.

Wait, you made the single drive into an array on the Promise controller?
Then you probably had the Promise controller setting wrong all along. In the system BIOS (NOT Promise BIOS), you need to go to "Integrated Peripherals" and then "Onboard PCI Controller" or whatever (the name of the submenu depends on your BIOS version).
There you'll find an option called "Promise 378 Controller" that can be set to "Disabled, SATA, or RAID"
Yours must be on RAID. If you put it on SATA, you could've used the single drive without making an array.
If it's on SATA, there will be no option to enter the Promise BIOS setup, and it will NOT call itself a "FastTrack" controller. When it is set to RAID, it will use the FastTrack BIOS and give you an option to enter disk setup.
Having a single disk array isn't really a problem... but it's not necessary if you don't have any real RAID arrays on the controller.
I currently have my Raptor array on the Promise controller, and my two largest PIDE drives on the IDE3 connector. Each of them is in its own "array" so that it can be recognized while the Promise controller is in RAID mode.

Similar Messages

Anyone use hypersonic 2 and logic express 9?

anyone use hypersonic 2 and logic express 9?
Message was edited by: Kajun Muzik

Actually I have found a way for at least the instrument plug ins to be accessed.
I was able to set up an instance of Sculpture in MS2 and record it in LE using Soundflower.
Route the audio from MainStage to Logic and record onto an audio track in Logic as follows:
If not already installed, get SoundFlower. After installing it.
A) Setup the sound you want in MS2 and audio output to Soundflower (remember to Apply Changes or it does not hold).
B) In Logic Express set the audio input to Soundflower and create a new audio track for recording. Important: set Soundflower's audio output to however you listen to your audio or you won't hear anything.
C) Press RECORD and start playing, LE captures Mainstage's sound.
I have not tried to wire LE's output to MS2 to take advantage of Space Designer. but since this functions, I'm not sure why that couldn't work as well. It is still flipping though a few screens though...might just be easier to get Logic Pro from the App store....

Has anyone using a PowerMac and Tiger got a Phaser 8570?

Has anyone using a PowerMac and Tiger got a Phaser 8570?
There are drivers for IntelMac 10.5 and 10.6, but nothing for PowerMacs.
I was thinking of upgrading from our 8550 - if there's a driver that will do - anyone able to help?

Additional information.
Had some problems with the 8550 and decided to take up a Xerox trade-in offer.
The ColorQube 8570 not only works perfectly with Tiger, it's a lot faster and quieter than the 8550.
Which answers the question.

Anyone using Login Pro and PowerCore Firewire

I have a G5 dual 2 gig with 4 gigs or RAM, 2 x 160 LaCie HD, RME Firewire 800 and PowerCore Firewire. I have been having issues with PowerCore losing connection, plug-ins load and are disabled, and total system lockups.
For testing, I removed all audio IO drives and used internal audio, remove all midi drives and I am still having the same issues. Anyone using Login Pro and ProwerCore Firewire successfully?

I am on the same machine as you. Most of my problems (similar to what you report) have been due to the driver/software of the Powercore. Luckily for you, TC doesn't have phone support, so you can be spared the immediate relief you don't want and wait the 48 hours for a general email response that says you get to wait another 48 hours until someone gets back to you.
That said, Powercore FW works fine for me. It sounds like you are using a lot of FW devices, which might also contribute to your problem. I've found that you can actually overtax the FW ports on G5's to the point where they stop working properly, causing random connection loss.
Does the powercore connect through any other device?
Trying unplugging your LaCie's and see if that helps.

Has anyone used Firefox Sync and Xmarks at the same time?

Firefox is my primary desktop browser. On my desktops, I use Xmarks because I use Firefox, IE and Chrome. It enables me to keep my bookmarks synced across browsers as well as use home/work profiles, etc. However, I'd like to use Firefox Sync so I can sync the bookmarks to my smartphone. Has anyone successfully tried this? I thought I'd ask before trying it myself just in case. Thanks!

Using Xmarks and Sync simultaneously will create a mess.
You can create a new profile, import the bookmarks from your main profile, and set up Sync for the new profile.
The flip side is, bookmarks from your main profile would not get synced with your new profile.
Alternatively, Xmarks is also available for Android.
https://play.google.com/store/apps/details?id=com.xmarks.android&hl=en

Has anyone used switch control and siri at the same time?

Has anyone used accessibility switch control and siri at the same time?

Using Xmarks and Sync simultaneously will create a mess.
You can create a new profile, import the bookmarks from your main profile, and set up Sync for the new profile.
The flip side is, bookmarks from your main profile would not get synced with your new profile.
Alternatively, Xmarks is also available for Android.
https://play.google.com/store/apps/details?id=com.xmarks.android&hl=en

Does anyone use both iPhoto and Aperture

I just got an mac book pro and I am trying to decide what to do with my iPhoto library that is on my old G4 eMac. I'm wondering if the best (and safest) plan would be to transfer that library to the new machine, bring it into iPhoto and then import the entire library into Aperture.
On second thought I wondered if it would be a good idea to leave everything in iPhoto and just open images in Aperture only when I want the extra editing tools... using Aperture for keeping all the "prime" photos and iPhoto for snap shots and iPhone pictures.
And... is it even possible to import the library from another machine directly into Aperture?
Thanks in advance,
bd

Pick one and stick with it. They don't actually integrate very much.
Aperture and iPhoto are entirely different applications that work in very different ways.
The only communication between the two is as follows:
Aperture is able to parse the iPhoto Library to allow it to import the contents while stacking the Originals and Modified versions, preserving metadata and so forth.
Aperture can share its Previews with the iLife apps, including iPhoto.
That's it.
So, specifically, what interaction there is between the two is designed to facilitate migration from iPhoto to the more powerful app. After that, iPhoto has exactly the same relationship to the Aperture Library as, say, Pages or iMovie.
iPhoto has no knowledge of, and knows nothing of how the Aperture Library works. It cannot read the Aperture library.
So if you decide to try this:
using Aperture for keeping all the "prime" photos and iPhoto for snap shots and iPhone pictures.
You'll end up using two apps to manage two different sets of photos, with twice the complications. Aperture is not an "external editor" and can't be used as such.
Think: Writing your novel in Word and TextEdit at the same time. "I'll write this chapter in Word, this paragraph in TE and then back to word..."
What of you wanted to sync your Photos back to your Phone? Which library will you use? You can't use both.
And... is it even possible to import the library from another machine directly into Aperture?
The routine would be to move the Library to the new machine and them process it into Aperture. Then trash the unwanted iPhoto Library.
Regards
TD

Anyone using a LaCie external SATA drive?

LaCie has a "LaCie Two Big with PCI-E Card 2-Disk RAID System with SATA II" which might work for my purposes.
I'm using a late 2005 G5 Quad with PCI-Express slots. I wonder if anyone with a similar G5 has tried this drive and might say what their experience with it and the included PCI-Express card has been?
Thanks, denny

No experience with that particular LaCie or PCI-e. However, I have some experience with LaCie external FW drives, Granite Digital SATA drive(s)/enclosures with a Highpoint PCI-X card and a MacGurus SATA II drive/enclosure with the Sonnet PCI-X card and of the bunch I MUCH prefer the MacGurus. Sold all my LaCie drives after having to send a 500GB drive back... and then it came back still broke. THe only FW drives I have left are "old" G-Tech drives. The Granite Digital is OK, but LOUD. I love everything about the MacGurus enclosure, especially port multiplication.
Mike

Anyone using source control AND cloud sharing?

Hi. I'm curious if anyone has any experience or tips to share about a RoboHelp environment that uses BOTH source control and cloud sharing.
My company uses perforce. I'm purchasing a couple copies of TCS5, one for me in California, one for writer colleague in Europe. I'd like to use Perforce for version control/backup, but use Dropbox for RH asset sharing and sync. Is this workabout? I'm guessing that the Dropbox/sync mechnism won't work if one or both of us has not checked out a file that needs to be (automatically via sync) updated. ("Not checked out" = file is in read only state.)
If RH automatically checks files in/out of perforce in order to complete a cloudshare sync, that would be most cool!
Thanks in advance for your ideas!
-Kurt

Hi Kurt
Have you tried the scenario with RH 11?
It should automatically check-out the file or should prompt for it based on the settings Tools -> Options -> Version Control
I tried with Robo Source Control and SharePoint. And it is working for me. Check-in has to be done mannually.
Please try and let us know the result.
Thanks

Has anyone used Ethernet Gateway and LabVIEW, communicating with Ethernet/IP protocol ?

I have a PLC system (Jokab Safety B20) together with Ethernet Gateway (also Jokab Safety type E1).
What I want to do is to communicate with this unit using LabVIEW Ethernet/IP.
Read a couple of data and write a couple.
Has anyone anything like this with LabVIEW and Ethernet/IP ?
I'm completely new to using PLC's, but I have made a minimum PLC application, but can't get communication to work with LabVIEW (+ Ethernet/IP).

i generally use an OPC server to talk to he PLC and then use Datasocket to talk to the OPC server tags.
if that gaetway thing is an OPC server then you maybe abel to do data socket R/W via it.
Otherwise the NI OPC server may support that widget and (at the rate I bill out) is a good deal in the eyes of most of my customers.
Ben
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction

Anyone use a lifedrive and arch?

i'm having big issues trying to get them to sync, followed all the tut's i can find online, and i have the pda recognizing the bluetooth dongle i have on the computer, but as soon as i try to connect for a sync i get "... port is in use,....." on the pda can't remember exact wording, on another computer now..
does anyone have this working that could lend me a hand?
thanks

Quote
Originally posted by Del UK
Hi Yabba,
Will try and borrow card and see what happens......... please allow 24-96 hours, before I test this.........
Del
I will be very happy if you can try same card as i have. . so i know if its the tv-card or the mobo that have the error .. hehe.
Take your time m8 .. and thanks.

Anyone using Nokia =vr20 and VoIP successfully?

Coz I'm not!
If I try and connect to my configured WiFi AP using the Internet Tel app (and Connect to service) it says "Connecting to default via MyWifi" followed almost immediately by "Unable to connect to the connection network".
If I go to a contact and select Options, Internet Call (as an alternative way of connecting) "Requesting Registration" followed by a message "Phone not registered with blah blah... Register now?" followed by "Registering to service" and a nice "Unable to Register to service" message.
Both ways of connecting return very quickly and the WiFi symbol comes up only BRIEFLY (but does come up).
However, and this is where it gets really interesting, if I first make a connection to MyWifi (say by using the front screen wifi app, opening a browser and then backgrounding the browser) both methods work fine. So it's definitely not my SIP settings but something to do with usuage of the WiFi connection.
Any help *GREATLY* appreciated since I've tried everything and have done loads of Googling but to no avail. It all worked fine in v12. Since 20 onwards I've had to go through the hassle of bringing the WiFi connection up first before making VoIP calls (as a workaround) but as you can imagine it's very tedious!
Solved!
Go to Solution.

My access point uses my own DNS server. I'm not using DHCP but I don't have a problem with the Access Point. Or in fact the SIP (since if I bring the connection up first via a browser it works fine). It just seems to be the combination of bringing up the WiFi connection when trying to register the SIP that it fails. The WiFi connectivity icon flashes up briefly but you almost immediately get an error.
There is no port forwarding on the firewall although I can't see how this would help since this would only be incoming traffic (I assume you mean DNAT here). There are no restrictions on outbound traffic and also I don't use NAT since I can use a public address for my access point configuration (lucky me).
I guess I'll just have to wait till Nokia fix it. Boo.

Does anyone use virtual dj and know who to erase duplicate music files?

Anyone out there have a program called Virtual dj currently?

Hopefully you have sorted your duplicates out by now, but just in case, and for anyone else searching for a solution to the same problem...
I've written a script called DeDuper which can help remove unwanted duplicates. See this thread for background.
tt2

Anyone using gmail imap and and Apple Mail?

Can you tell me if, when you use Apple mail for imap gmail access, what address source does it use?
Does the imap pull up the address auto complete of gmail or does it rely on your address book on your mac (or both)?

I'm using Google IMAP with Mail and it uses the addresses I've got in my Mac's Address Book. Can't tell you if you can also use addresses from Gmail but I'd be inclined to think you could. Joe Kissell provides an excellent, if lengthy, explanation of how to get Mail and Gmail to work together here: http://db.tidbits.com/article/10253

Anyone use Cineform Codecs and have trouble reading the entire clip in the new CC timelines?

I have 3 36+ minute clips in an old CS4 timeline all originally encoded with a CineForm codec. Recently upgraded to CC when computer took a dump. I openned the old timeline and updated it to CC but the timeline will only show the first minute of video (which works great) and then it goes black. Is this a leap from CS4 to CC issue or a Codec issue?
Any help is much appriciated.
- Mike

In addition to the codec, you'll need the CineForm AVI File importer which installs into CC versions of Premiere with GoPro Studio Premium. You can theoretically copy it from an older version of Premiere and Prospect 4K though. Contact me through the CineForm Support website and i can help you out with this.

Anyone Using Via Raid0 And 1 Sata On Promise?

Similar Messages

Maybe you are looking for