Anyone with corsair value select memory.

Hi,
I have the neo2 board, and 4 512 meg corsair value select ram. With two memory chips, it works fine, but with four, I get errors, even with memtest 86. All the chips work fine one at a time, or in pairs in every socket.
My question is does anyone else have problems with 2 gigs of ram, and/or corsaid value select memory. Also is the value select with all four chip be supported soon?
Thanks.

Try setting your timings to 2,5-3-3-7 , voltage to 2,75V in bios on next boot. That will probably do the trick.

Similar Messages

  • Corsair Value Select RAM causes random RESTARTING, CORSAIR RAM NOT FOR MBP

    I thought I got a great deal on 1gb ram for my MBP when I purchased the Corsair RAM from zipzoomfly...but the RAM causes random restarts/shutdowns.
    Corsair VS1GSDS667D2 1GB DDR2-667 PC2-5300 Value Select SO-DIMM

    I thought I got a great deal on 1gb ram for my MBP
    when I purchased the Corsair RAM from
    zipzoomfly...but the RAM causes random
    restarts/shutdowns.
    Corsair VS1GSDS667D2 1GB DDR2-667 PC2-5300 Value
    Select SO-DIMM
    I had reported this a couple of weeks ago. To confirm what rtio says, this ram will not work with a MBP. It's not compatible.

  • Issue with Blank Value selection in Dropdown List

    Hello Experts,
                        I am facing one strange issue in Adobe Forms Drop Down(DD) list. Foll. is the list data which contains a several item data & blank value. After item data selection user must be able to select blank value in case he doesn't want to set the value to Order Unit as shown in screen shot below.
                                  Now my issue is after any of the item values selection (for ex. BAG - BAG)  user is not able to set the blank value again at my client system. However its working fine in mine. When checked client is using Adobe Reader 8.0 which is same as mine.
    Thanks in advance.
    Regards,
      Amit

    Hi Steve,
                   Thanks for the reply. We have a blank value in the DD as a list item, where key & description is empty space. As i posted above user must be able to select that blank item if doesn't want any value for Order Unit. This selection is working fine in my sytem, but my client facing the issue where he can not select the blank value from DD.
    Thanks,
    Amit

  • OPTIONAL PARAMETER WITH NO VALUE SELECTED

    I have an optional parameter and I want to place the selected value in the Page Header.  Since the selected value is a number, I want to give it a name.  The problem I am having is when I don't select a value, my naming forumula doesn't work.  I tried the HasValue function, but I don't think I'm using it properly.
    // This did not work
    IF {?SUPPLIER}= 10001 THEN "NESTLE PRODUCTS ONLY" ELSE
    IF {?SUPPLIER}= 10005 THEN "UNILEVER PRODUCTS ONLY" ELSE
    "ALL PRODUCTS"
    // This did not work
    If (not hasvalue){?SUPPLIER} then "ALL PRODUCTS" ELSE
    IF {?SUPPLIER}= 10001 THEN "NESTLE PRODUCTS ONLY" ELSE
    IF {?SUPPLIER}= 10005 THEN "UNILEVER PRODUCTS ONLY" ELSE
    "NESTLE AND UNILEVER PRODUCTS ONLY"
    Got any suggestions?

    Hi,
    Well if you select multiple values in a parameter and drag the parameter or the formula containing the parameter, then it would always display the first selected value.
    Here's a dirty way:
    If NOT(HasValue({?SUPPLIER})) then "ALL PRODUCTS" ELSE IF
    ubound({?SUPPLIER}) = 1 then
            IF {?SUPPLIER}= 10001 THEN "NESTLE PRODUCTS ONLY" ELSE
            IF {?SUPPLIER}= 10005 THEN "UNILEVER PRODUCTS ONLY" ELSE
            "NESTLE AND UNILEVER PRODUCTS ONLY"
    ELSE IF
    ubound({?SUPPLIER}) = 2 then
    "NESTLE AND UNILEVER PRODUCTS ONLY"
    Let me know how this goes!
    -Abhilash

  • Corsair Value Select?

    OK i have read countless forum posts about this. And how it does not work. I purchased mine about 25 days ago. and randomly its has shut down. About probably 6 times total. But when i run memtest and AHT memory seems fine. should I still return it. I was more wondering if some of the people that had problems with this memory had memtest pass. All the posts I have read it seemed to fail. Thank you

    I bought some of this RAM from a Fry's and so far (knock on wood like substance) I've not had any issues. I suspect since it's 'cheap' RAM that it may be somewhat inconsistant from one stick to the next. Since Apple's hardware is more sensitive to this kind of thing (I've sen PC's run perfectly with RAM that fails tests) they are probably going to choke on marginal RAM. If I have any issues at all with the machine I am going to exchange the RAM for a different type but at 1/3 the cost of Apple's RAM I am willing to take the risk.

  • MSI Neo4-F and Corsair Value Select DDR400 512x2 Cas 2.5 unstable to the max

    Hi, how can I fix this ?
    Can anybody help me ?
    I know this caused the problems cause I switched to KINGSTON Value RAM Cas3 512x2 DDR400 and its 100% stable now.
    Please help me I need to return the Kingston.

    Hi there,
    The colors of the dimms are to diferenciate the channels (because of the dual channel thing) one color is channel A the other channel B.
    So when you put 1 stick in one color and the other in another then you have a dual channel memory system, if you put the 2 sticks in the same color slots then you have a single channel memory system and less performance (obviously ).
    As for the voltage, there is a very very very ....... long term damage, if the memory was not intended to work at that voltage, but do not worry about that.
    Be well....

  • Corsair Value Select on MSI K8N NEO Platinum Edition

    Does anyone have this combo? (A64 CG) and can tell me some clock result and bios etc how high fsb and so on
    THX
    /Stiga

    value ram usually will not clock high, higher end ram like corsairs xms is better suited for ocing

  • Enabling and disabling input filed based on the Dropdown values selection

    HI,
    I have a requirement with Adobe Interactive forms being called from HCM Forms & Processes. We have a drop-down list and a inputbox.
    based on the values selected from the drop-downlist, the input box should be visible and hidden.
    If the input value is visible, I got to send  some part of the value selected from the drop down to the input field.
    i tried to write the following script in the click event of dropdown  but the input field is not appearing with any value selection.
    if data.Layout.CH1.CHContent.ISR_DDL_1stSelected.rawValue = "00000000" then
    data.Layout.CH1.CHContent.ISR_NEW_COST.presence = 'Visible' else
    data.Layout.CH1.CHContent.ISR_NEW_COST.presence = "Hidden"
    endif
    Thanks in Advance,
    VR.

    Hi Mukesh,
    THanks alot.
    Yes,  The Split functionality is working.  I have added the code in 'Change' event and  for selecting the value from the Drop down, am  writing the code in the 'exit'.
    In addition to this, I am populating the values to the drop down from the Generic service.  The problem is, while running  the  Process from Portal and check and send button,  the fields fetched from the generic service & the dropdown values are getting refreshed. i hope, this is because of the java script.
    pls. suggest me if this can be handled .
    Thanks &Regards,
    Venkatesh.

  • MSI K8T Neo-FIS2R (Socket 754) and Corsair 1GB DDR Value Select PC3200 Kit (2x512MB)

    Hi I just ordered the following from overclockers.co.uk and wanting some confirmation that the memory will be compatible with this Mother board
    Corsair 1GB DDR Value Select PC3200 Kit (2x512MB) and MSI K8T Neo-FIS2R
    Thanks
    Kevin

    kevtucker,     
    I'm running the same setup up as you and have not experienced any ram related problems so far. I'm happy with it and it is very stable.
    Every ram has different settings. For the corsair 1gb value select (2x512mb) you must make sure you use these settings for the best results:
    put them in slots 1 and 3.
    use the settings 2.5-3-3-8
    set the ddr voltage 2.7
    I got that information straight from the official corsair forums:
    http://www.houseofhelp.com/forums/showindex.php?t=24410
    Good luck.

  • RAM: Has anyone else had good luck with Corsair?

    First of all, thanks Bas and Scottg26 for pointing out the correct version of Memtest86+.
    I know that Corsair has a crappy rep around this forum when it comes to the Athlon 64.  However, I've had nothing but good luck so far (knock on wood).  I've been up and running for almost a month now with no BSODs and the computer has booted every time so far.  I'm using Corsair TwinX 1024 LL in slots 1 and 2 with the speed settings on Auto in the BIOS with a voltage of 2.6.  I've run Prime95 for up to 10 hours or so with no errors and I just ran one pass of Memtest86+ v1.00 with no errors.  It took 18:50 and showed the following settings:
    Memory: 1024M  1447MB/S
    Settings: RAM: 200Mhz(DDR 400) / CAS:2-3-2-6 / Single Channel (64 Bits)
    However, I will point out that the only real world test it's really passed so far is playing Call of Duty.
    Here's a link to the actual RAM on NewEgg:  http://www.newegg.com/app/ViewProductDesc.asp?description=20-145-435&catalog=147&manufactory=BROWSE&depa=1
    Is anyone else happy with their Corsair RAM so far or did I just get extremely lucky?

    Quote
    Originally posted by amxandy
    I read the horrible reviews for Corsair on this forum after placing my order for a stick of Corsair CMX512-3200C2PRO memory (I couldn't resist the activity lights). I have had no problems running at specified memory timings. I have always had good luck with Corsair and will continue to use them.
    Yeah They are neat at that. Question is how well do they overclock?
    I'm getting a 28Mhz fsb overclock out of these dimms that I have and They are used I admit, But like the seller said they are great overclockers!

  • Populating select list in a JSP with enumeration values

    I'm working on a JSP in which I need to populate a select list with enumeration values.
    Everytime I'm trying to insert these values (using enum.nextElement()) in a select box only the first enumerated value gets inserted correctly, the rest of the values shows up outside the select list. I would appreciated any help...thanks!!!

    I'm not exactly sure how your generating your list to begin with, however the following code will work:
    <form>
    <select>
    <%
         java.util.Vector v = new java.util.Vector();
         for(int i=0;i<12;i++){
              v.addElement(new Integer(i));
         java.util.Enumeration enum = v.elements();
         while(enum.hasMoreElements()){
         Object obj = enum.nextElement();
         out.println("<option name='"+obj+"'>"+obj+"</option>");
    %>
    </select>
    </form>Anthony
    BTW does anyone know why the greater than symbol never renders properly in these forums when text is encapsulated in the code tag?
    pre:
    >code:
    >

  • How to get all the values of a variable with F4 with checkboxes to select

    Dear Experts,
    After Executing a query by giving let 3 values(Out of 10 Values) to a variable.
    To give 2 more input values to the same variable(i.e.,total I wanted to give 5 inputs this time ),after refreshing the query,for that variable if I click F4, I am seeing the historical values(i.e.,3) and remaining 7 values also But with out any Check Boxes besides them to select the 2 inputs.
    In the same F4 Screen, If I click all values(an Icon at The bottom),then also Im seeing but no check Box.
    I hve tried by deleting the Delete Personalization also,but no use.
    Please tell me How to get all the values with F4 with check boxes to select ,whatever I want??
    Thanks in advance

    Take a look at the InfoObject and go to the Business Explorer tab. If the 'Query Def. Filter Value Selection' is set to 'Only Values in InfoProvider', you're only going to get the values in F4 that exist in the InfoProvider, not everything in the Master Data. This would need to be changed to the value of 'Values in Master Data Table' if you want it to show everything possible when F4 is chosen.
    Likewise, you're going to need to look at the query and go to the Advanced tab for the InfoObject. Make sure that the radio button for 'Values in Master Data Table' is selected. If not, then you should change that selection.

  • How to select rows with min value on a specific column

    I have a query:
    select
      m.x1,
      round (to_date (l.y1, 'mm/dd/yyyy HH:MI:SS AM') - m.x2, 0) as numofdays
    from
      table1 m,
      table2 l
    where
      l.x3 = m.x3 and
      to_date (l.y1, 'mm/dd/yyyy HH:MI:SS AM') >= TO_DATE('01012013','MMDDYYYY') and
    and I got this result table:
    x1 (ID)
    numofdays
    001
    5
    001
    10
    002
    2
    003
    3
    003
    1
    004
    0
    005
    66
    several ID's have multiple values on the second column, I want to have only distinct IDs with smallest "numofdays" like this:
    x1 (ID)
    numofdays
    001
    5
    002
    2
    003
    1
    004
    0
    005
    66
    Any ideas?

    Hi,
    The most general and versatile way is a Top-N Query:
    WITH   got_r_num AS
        select
                m.x1,
                round (to_date (l.y1, 'mm/dd/yyyy HH:MI:SS AM') - m.x2, 0) as numofdays
        ,       ROW_NUMBER () OVER ( PARTITION BY  m.x1
                                     ORDER BY      to_date (l.y1, 'mm/dd/yyyy HH:MI:SS AM') - m.x2
                                   )  AS r_num
        from 
              table1 m,
              table2 l
        where
              l.x3 = m.x3 and
              to_date (l.y1, 'mm/dd/yyyy HH:MI:SS AM') >= TO_DATE('01012013','MMDDYYYY') and
    SELECT  x1, numofdays
    FROM    got_r_num
    WHERE   r_num   = 1
    If you'd care to post CREATE TABLE and INSERT statements for your sample data, then I could test it.
    Notice that the sub-query (got_r_num) is exactly what you posted, only with a new column (r_num) added to the SELECT clause.

  • Initializu00EDng select options field with default values and with NO INTERVALS

    Dear All,
    I have used WDR_SELECT_OPTIONS technology within WD Abap.
    I also have added the fields which have to be taken into consideration.
    lt_range_table =
    wd_this->m_handler->create_range_table(
    i_typename = 'PLANT' ).
    wd_this->m_handler->add_selection_field(
    i_id = 'PLANT'
    it_result = lt_range_table
    i_read_only = read_only ).
    Can I assign two values to this field 'PLANT' whereby the user may take only these values.
    I mean kind of pre initializíng of this select options field with default values.
    Due to this handling it should be prevented that the user can give other values
    except this values.
    Additonally it should be fine whether it is possible to disable the second input field
    of this select options field like NO INTERVALS .
    Regard
    sas
    Regard
    sas

    wd_this->m_handler->add_selection_field(
    i_id = 'PLANT'
    it_result = lt_range_table
    I_NO_INTERVALS = 'X'
    i_read_only = read_only ).
    Pls check 'WDR_TEST_SELECT_OPTIONS' web dynpro component

  • Exporting to Vimeo with "Anyone with Password" selected

    We routinely upload to Vimeo using Final Cut X's Share menu. It works great. It remembers the account and password and remembers the "Anyone with Password" password.
    In Motion 5 it allows me to select the same option, but at the bottom I get a yellow triangle with "The Privacy Password field must be completed." I do not see anywhere within window or any of the tabs to allow this password to be entered.
    Anyone know a workaround or a fix? This increases the workflow as I need to export, then upload through the browser.
    Thoughts?
    Thanks!

    seems to be a bug/oversight... workarounds?

Maybe you are looking for