Ap 1252/Enable password after upgrade to LWAPP

Hi i converted a 1252 to LWAPP with the upgrade tool, but when the ap restarted with the ligthweigh image the access point does not accept the default enable password "Cisco", before upgrade to lightweigh image the enable password was "Cisco" too, now i can not configure the ip address of the controller.
Thanks.

If The ap's havent joined the wlc yet you can enter these commands:
AP#lwapp ap ip address
AP#lwapp ap ip default-gateway
AP#lwapp ap controller ip address
AP#lwapp ap hostname
(optional)
Here is a link:
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_tech_note09186a00808e2d27.shtml

Similar Messages

KWallet stopped recognize password after upgrade

Hello,
I have two kwallet profiles, (at the moment extra/kdeutils-kwalletmanager 14.12.1-1 and extra/kwallet 5.6.0-1)
The "kdeprofile" works as always, and another wallet I have created long time ago, stopped finding it's password after upgrading this week.
The second one, had a password that I have always used, but after restarting kde (logout -> returnrning to kdm), it stopped opening it, claiming that the password may be incorrect (error -9).
As far as I can tell, there is no way to restore/recover/change passwords, but could it be just a bug that is fixable?

I have almost a similar error (I've switched from kdewallet-git to kwallet from [extra]). I've fixed when back to kwallet-git, because the git version transform the wallet profile to new version, but when back to older kwallet this don't recognized it (always need put the password but is never recognized (error 9)
in my case, i think is fixed in kwallet 5.7.0 because this commit https://projects.kde.org/projects/frame … a159b45849 is not apply in the 5.6.0 (or more older commit)
try to install kwallet-git and test with older commits (use #commit=sh1 in source=() array. see the pkgbuild VCS wiki ) until to fixed
the list of commit is this https://projects.kde.org/projects/frame … repository
greetings
Last edited by sl1pkn07 (2015-02-06 22:49:33)

TS3988 iCloud will not accept any passwords after upgrading OS. 2 days of trying every password I have ever used, AND changing Apple ID and iTunes ID, still nothing. Can't backup on iCloud anymore.

How can I use iCloud again after upgrading OS to Mountain Lion? 2 days of trying every password I have ever used, AND changing Apple ID and iTunes ID, still nothing. Can't backup on iCloud anymore.

Apple ID's can be used for anything, a single ID can be used for all your accounts (ie iCloud, iTunes, MAS, Apple community etc), ideally this would be the way forward. So far as iTunes goes you need to continue to use the same ID as you have always used or you will lose access to your previous purchases and your iTunes match subscription.
If you are using a second ID for iCloud, you can continue to do so or use the ID you use for iTunes, but if you choose the later you will need to move all your calendar, contact etc data to the account using the ID you use for iTunes.
When (if) you change which account you use you would delete the account on an iOS device and log back in with the correct details, on a mac you would sign out in the iCloud system preference pane.

Problems with passwords after upgrade to Mavericks

Hi,
After upgrading to Mavericks I have problems with passwords. MacOS allows me to log in with my password but when I want to install software it does not accept my password. I can go to the user tab in system preferences and change my passwort there. With the new password it works, but when I change to the old password, I have the same problems. Strange ...
Thanks for help

OK. I found the problem (probably it is not related to the upgrade): When I install an application and the installation procedure asked me for a password it switched the keybord driver to a language I only use infrequently. Since my original password contained special characters the change of the keyboard driver was the cause for my typing in a wrong password. When I tried changing the password I used "abc" and this worked since it did not contain any special characters. So everything explained and a bug for Apple to fix.

Toshiba Satellite C40D-A HD recovery solution to lost password after upgrade to win 8.1?

Hi,
Part No.: PSCDSL-009001
After I bought this laptop in Manila, I initiated it with ONE local account, and NO password, and created a USB recovery stick.
There are no privacy-critical data on it, so I'm perfectly happy using it without password.
It came with Windows 8.
Lately I was 'offered' an upgrade to Windows 8.1 through some window in Windows, which I accepted, assuming my old account would be migrated.
During the upgrade, I was forced to get and enter a Microsoft Outlook.com account in order to be able to continue.
I don't want an outlook.com account, still assumed that my previous account would be properly migrated (which it *should*), and registered a bogus outlook.com account, started working, and forgot about the account.
After some time of inactivity and before I was able to create a new recovery USB, the laptop went into sleep modus, after which it was impossible for me to login again, because the thing was asking for my outlook.com account, which I had forgotten, and didn't want in the first place.
Account recovery @ accounts.live.com is impossible due to lack of sufficient data 'to confirm my identity'.
So now I'm considering a HDD recovery, if possible. There are however some questions to be answered before I proceed with that.
1. Is there a possibility that this laptop (bought in a quite well known shop in the Asia Mall in Manila) has some irregular windows installed, so that it will be impossible to recover it? And will I be notified of that before I destroy my original windows 8?
2. Do I need a windows activation key in order to use it after the recovery? (I don't have/can't find one.)
3. To be sure, I looked at https://support.toshiba.com/support/serviceUnitVerification?orderType=SFF in order to check if I'd be able to get a recovery media, but it says: "Please verify you entered the correct serial number, and that your PC was sold in the eligible region."
Now I checked the serial No., and my entry was correct (from the sticker on the laptop), and I have no idea what 'sold in the eligible region' has to do with it, nor do I understand what it is referring to.
4. I have had a linux distribution installed on it before, but have been so careful (enough, I hope) to ONLY remove the partition with the windows installation. Proof of this, is that I was able to reinstall windows 8, before the upgrade to 8.1) from the USB drive. Would this history interfere with a succesful recovery back to windows 8?
Thanks in advance for your advice.
Solved!
Go to Solution.

Satellite C40D-A108 (PSCDSL-009001) Specs
First, this is the peer support forum for Toshiba USA, which hosts the forum on their website. While you're still welcome here, your unit is a Toshiba Asia model, and you can register with them at the previous link. So, that's why you get the "Please verify....that your PC was sold in the eligible region." message. Your unit's serial number would not be regisitered with Toshiba USA.
With regard to your questions:
1) - I doubt it's an illegal copy of Windows if you bought it at a reputable shop. Plus, you would not have been able to 'Activate' Windows 8, nor been offered the upgrade to Windows 8.1 if the original copy was illegal.
2) - No, you don't need an activation key to use the Toshiba Recovery.
3 & 4) If you used the Toshiba Recovery USB to rebuild Windows 8 before the Win8.1 upgrade, it is no proof at all that you did not destroy, damage or corrupt the Toshiba Recovery Partition on the hard drive when you installed Linux. However, by using the recovery USB, you would have rebuilt the Toshiba Recovery Partition nonetheless. If you in fact 'upgraded' your Win8 installation to Win8.1, as opposed to doing a 'clean' or 'custom' install of Win8.1, then the recovery partition should still be intact.
Bottom line, if your recovery partition is sill intact and accessible, or if you still have the Toshiba Recovery USB, either way, you can still rebuild your system to its factory default out-of-the-box setup, that is to Windows 8. But, you'd have to satisfy Microsoft, you are who you say you are to get back to Windows 8.1.
You should take a good look at the appropriate sections of your User's Guide.
Get back to us again if you have any more questions. Good luck.
Mike

Why is firefox not saving previously stored passwords after upgrade to 33.0, all proper settings to have this happen are selected and were in previous version.

After I upgraded to FF 33.0, none of my previous website usernames or passwords were saved when I browsed them. None! I have looked at FAQ responses and carefully looked at my 'Privacy' settings and they are all set to have FF save user names and/or passwords. My cookie settings are 'remember browsing...history' - 'remember search...history' - 'Accept cookies...' 'Accept third-party cookies / Never - and 'Keep until I close FF'
Do I need to select 'Keep until: they expire' for cookies?
Tom F.

hello tom, can you try to remove the remember passwords addon (this is now longer needed, since firefox is now ignoring the autocomplete=off parameter in password fields by default), restart the browser and see if this is making any difference?

Lost my WEP password after upgrading my AIRPORT software

A year ago, I joined SBCGlobal.net
I have a faint memory of a password that I had to insert in order for my G4 to use the network from a remote location. I also have a faint memory that wherever I got the password, it did not work, and after calling SBCI, I was told to insert a $ sign in front of the password. That worked.
I just today upgraded to Airport 4.2. When I restarted, my network was still visible under the Airport icon on the desktop, but the computer did not connect. Manually clicking on the network (2Wire....) brought up the WEP dialogue page and asked for my password.
Is this something I had to create, or was it supplied by the SBC folks? If it's gone forever, can I fix the problem in some way?
Thank you,
Anene

Read the user manual for your 2Wire router - it will tell you what the default WEP key is for your router.

How to start/enable BSP after upgrade

Hi
We recently did upgrade our system from 4.6 to WAS 620.
now after the upgrade is done I want to start using BSP applications. But when I try to connect to the URL I just get a Connection refused error message in the browser.
So I figure I have to activate or config the system to enable BSP ? I need some info or tips on how to do just that.
Best regards Sigurdur

Hello Sigurdur,
start Transaction SICF and activate service tree with a right click on the server.
Regards
Gregor

Mail doesn't recognize password after upgrading to Mountain Lion

After updgrading to Mountain Lion:
The gmail account in Mail began to ask for its password. it is preseent [in dots]; when i click to continue, dialog box indicates it doesn't recognize it.
i had time to to go over details in a gmail help page with details (port numbers and other things).
I decided to start over.
I deleted the account in Mail, system preferences, Accounts, began anew. Later I deleted inactive Gmail from  menu, Mail. Contacts & Calendars.
Reading some interventions in Communities mentioned the Key Chain. I had changed the Gmail password while using an older Mac Book. In June i purshased a MacBook Air and had Apple migrate my files from the old to the new mac. Mail had not password problems until I updated to Mountain Lion, which I thoroughly enjoy.
I'm at my wits end.
Throughout all this, Mail on my ipodtouch o.k.
I appreciate help.

Is it sleeping or shutting down?
Bootup holding CMD+r, or the Option/alt key to boot from the Restore partitirion & use Disk Utility from there.

Can't set password after upgrade to iOS4 on my iPhone 3g

It took forever but I upgraded my iPhone 3G with iOS4 upgrade. When I tried to open "General" settings the screen reverts back to the default first page with all the apps displayed. I want to set a password but I can't get past this screen. I have tried rebooting a couple of times but I can't get to the settings window. Any clues?

Hey karenw74,
Thanks for the question. I understand that you are experiencing issues with call audio quality. Do you have a case or screen protector on your iPhone? If so, you may want to remove it while attempting these troubleshooting steps:
If you can't hear a person on a call or voicemail or if the sound quality is poor on iPhone - Apple Support
http://support.apple.com/HT203800
If your issue persists, you can follow the steps towards the end of the article:
Get more help
If you've tried these steps and there's still no sound or poor sound quality from your iPhone, contact Apple Support.
Thanks,
Matt M.

Troubles with passwords after upgrade

Hi, we upgraded the system from 4.6 to ECC 6. and now some of our users have the problems with passwords (login).
We suspect that more users have the same password. Is it possible that in new verision users need to have different passwords?
Thanks and BR
Saso

Note: SAP ECC 6.0 password is Case Sensitive.
Regards
Vinayak

I don't remember my password after upgrading the iOS. help

I was installing the iOS5 on my iPhone 4. When it finished I got a message to enter my backup password. I don't remember ever setting one..nor did any of my normal passwords work! HELP

iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
Please Get the iPhone User Manual for iOS 5

My phone almost request apple store password after upgrade

within i am make update to my phone its starting to request apple store password , why i dont know ??

Make a Genius Bar appointment to avoid delay when you get to the Apple store.
http://www.apple.com/retail/geniusbar/

Had Lion 10.7.3 and spctl enabled, after upgrading to 10.7.4 i got this error message: 'error: invalid API object reference'

I had Lion 10.7.3 with spctl enabled, few days ago i had thru Software Updates > Upgrade to 10.7.4; i upgraded but this time when im trying to install an program i have the message that producer is not signed or software was from AppleStore so i tried to disable on Terminal, but i got this message:
'error: invalid API object reference'
i guess now i cant install anything because either i want to enable or disable the result is the same.

I have this same trouble with an IMac, was also 10.7.3 with spctl enabled, and after upgraded to 10.7.4, i cant install anything.

Changes in BW Extractors after upgrade

Hi,
My client is upgrading from R3 4.6c to ECC 6. I want to know what are all the changes in BW extractors in ECC. This will help me understand if our current applcations will be impacted due to these changes. Also, we will know what are the changes we have to make in BW after the upgrade to ECC.
Also, please mention where I can get the list of BW extractors for a given plug-In.
Thanks
Rekha

Hi,
Along with upgradation document you would get pre requisite note and BI content/Plugins information ( from Basis you can get necessary documents ) or you can get it from Service.sap.com.
generally when sourcesystem upgrade happens :
we have to check the mainly for enhancement part and Includelogic(CMOD)
Datasource content (Eg : R/3 4.6 we dont have RDA concept then now ecc we have RDA enabled DS After upgradation these kind of changes would get effected to the extractors )
we need to follow the upgrade check notes carefully .
Hope this would help
Regards,
Satya

Ap 1252/Enable password after upgrade to LWAPP

Similar Messages

Maybe you are looking for