AP 1300 in repeater mode problem

I have a 1300 workin as root and second 1300 that works fine as non-root, but cannot work as repeater(association problem). Also some of the commands in 1300 guide are missing from real 1300 IOS.The IOS is 12.4 What could be the problem?
Thank you

I stand corrected - but if you want to use the AP as a repeater - you need to set an infrastrcuture SSID. The AP needs to know which SSID to associate on when there is more that one SSID

Similar Messages

  • Repeat Mode problems

    Since i hooked up my ipod touch to the usb connector in my Acura, it is stuck in repeat mode.  How do I turn off repeat mode?

    On the left hand side of the s\palyback screen righ below the scrubber bar is the repeat selector. It is the arrowed racetrack icon. Tab it ito get to white.

  • Deos Aironet 1300 can provide the repeater mode to PT-link TL-WA601G

    Hello,
    I have a problem with Aironet 1300 to provide the repeater mode to PT-link TL-WA601G for extending the signal.
    I have two cisco aironet, i have configures as the bridge to link each other and WEP 128bit key.
    Then i bought TL-WA601G for extending the signal to my room. However after i configure on TL-WA601G as the repeater mode and put WEP 128bit key, TL-WA601G cannot get sent and received packets from Aironet.
    So what is the problem on this? How can i solve this issues?

    Cisco Aironet products can establish 40-bit Wired Equivalent Privacy (WEP) connections with IEEE 802.11b-compliant non-Cisco products. If you want to create a 128-bit WEP link, Cisco products only interact with other Cisco products. If you are using a third-party device with a Cisco Aironet product, you must set both devices to use 40-bit WEP.

  • Urgent Help Needed! .....key locked in repeating mode?

    Help please -I've done something stupid but I don't know what. Somehow the 'period' key on my keyboard is locked in a repeating mode and all sorts of complications have resulted...
    Briefly here's what happened:
    I was writing in InDesign CS when apparently I hit some combination of keys because all of a sudden the 'period' key went nuts typing periods.............. row after row after row. I tried to stop it but could not. I closed out of the document and by not saving changes was able to return to my original text. But whenever i tried from then on to type anything, the period key just takes off, regardless of applications running or not.
    I've found I can control the speed of the repeating by using my mouse system controls. I've slowed it down enough to where I can navigate some but I can't type anything, even a password because faster than I can type the machine inputs one or more periods and the password is rejected.
    I've restarted multiple times to no result. I've tried resetting the PRAM but the machine will not.
    With no applications running, when I can get the desktop open, a file is selected. If I try to select another file the highlighting moves to the selected file for a moment then jumps right back to the previous one. If I trash that file, the selection just moves to another?
    The problem is cross user too - I have two user files on the machine and the same thing happens regardless of which user file I'm working in.
    I've searched Mac help and can't find anything about repeating keys but that seems to be what's happening - the period key is stuck on if that makes sense.
    I've a major project to complete this weekend... PLEASE HELP!
    The problem is on my MacBook Pro Intel Core 2 Duo. Obviously I'm writing this on my desktop backup machine.

    The problem is cross user too - I have two user files on the machine and the same thing happens regardless of which user file I'm working in.
    That points to s 'system-wide' issue.
    Try resetting your SMC.
    Resetting the System Management Controller >>
    Also, you could try booting from your install DVD and see if it does it there. If it does not, it's more than likely a software issue and an Archive and Install should fix it.
    Mac OS X: About the Archive and Install feature >>
    -Bmer
    Mac Owners Support Group - Join us @ MacOSG.com
      Mac611 Mobile Mac Support - about.Mac611.com
       iTunes:MacOSG Podcast | YouTube.MacOSG.com
                       An Apple User Group 
    Have an iPhone or iPod touch? Enter Mac611.com in Safari on it for 'mobile Mac support.'

  • WAP4410N (Repeater-Mode) is crashing at least once a day

    Hello everyone
    we installed a WAP4410n for a customer who needed a wireless repeater to forward the signal to another part of the building. Everything is configured properly and works, until the device stops responding. This happens at least once a day, sometimes twice or even more often. When you power-cycle the device, after a few minutes everything is fine again. The lights on the device stay lid up after the crash. The wireless network is not discoverable after the crash though.
    The wireless-router that is forwarded is in direct site an at maximum 15 meters away. The signal strengts is good and the only traffic that is made is internet access for two PC over a 2mbit internet-connection.
    I tried updating the device from 2.0.0.5 to 2.0.0.12 K9 but this has not solved the problem. I'm not sure if this is a hardware-failure or a known software bug. Please let me know, what i can do to solve this.
    Thanks in advance

    Greetings,
    Usually when you use repeater mode from one of our access points the speed and range is cut by half, If I am correct 15 meters is close to 45 feet give or take, our max range for wireless is 120 feet configured as an access point,  when cut in half by the property of repeater mode your new repeated broadcast would have 60 feet give or take of wireless connectivity, if your clients are moving in and out of the total broadcast range and consistently requesting  DHCP from the WAP device you could generate a broadcast storm that could lead to the device locking up.  I would suggest tweaking with the advanced wireless settings at carefully and looking at the help tab to see what each setting does, perhaps trying different wireless channels that work best in your network and trying to stay within the wireless boundries of your total broadcast range. This is a mere suggestion and a personal point of view, however for more detailed and precise technical support regarding your issue please contact our support center 1-866-606-1866.
    Thanks.

  • WAP4410N work in Client-Repeater mode?

    I have purchased 4 of these devices about 2 months ago and have experienced all of the issues reported within this thread.  The came with the 2.0.0.5 FW rev installed, so unless the 2.0.0.5 on the cisco DL site is different, nothing I can do with that.
    I've tried making them work as stand alone AP's, Bridge<->Bridge, etc... all modes seem to lock up eventually needing a reboot to get any functionality back.
    Ultimately, I need to make them work in AP<->Client-Repeater mode.  I've not been successful in making them work in any mode for a prolonged period of time.
    having just rfound this thread today, I have not tried hard coding the NIC's to 100/full, but will give it a try.  If it works, great, but then that would defeat the purpose of buying an N radio AP.  I would like the potential 300Mbps throughput.
    Any update from Cisco on this?  Help!!!

    In my experience the WAP4410N worked perfectly for the purpose described in this thread, after following the directions given above. However, there is a little more information that will likely be helpful.
    The short: Connect the first WAP to the network in AP mode (I will call this one the primary), the second in WDS Repeater mode, assign the second a unique SSID, list the MAC of each in the configuration of the other, should be all set. Each WAP will allow clients to connect, the remote WAP will provide full network connectivity, including passing through DHCP.
    And I think this is a correct statement: client/repeater mode does not apply to the scenario presented in this thread. It seems as though the "client" would be the various workstations connection to the WAP. But in fact the "client" is the remote WAP, which is connecting to the primary WAP as a client, and then routing traffic through. My bet is this would apply to a use of a WAP4410N with another manufacture of AP.
    But, I had the same problems as amvita - none of this worked when I first tried.
    I think the reason is simple: I initially configured using the client/repeater mode. I started by setting up the remote WAP, assigned it a unique SSID, set up security, then configured for client/repeater. At the time that the WAP connects and authenticates to the primary AP, its unique SSID is REPLACED with the SSID of the primary. I guess this is clever - it would appear that there is a single SSID to connect, even though there are multiple WAPs forming the network. This configuration did not work, so I went back to the WDS Repeater mode. But now the SSIDs match between the primary and remote, and the pair does not work. So put back the unique SSID on the remote WAP, and everything should be good.

  • TLS mode problem

    Hi i am trying to fetch a mail from my Zimbra account. But i am getting the following error.
    What is this TLS mode problem? please help.
    javax.mail.AuthenticationFailedException: only valid after entering TLS mode
    at com.sun.mail.pop3.POP3Store.protocolConnect(POP3Store.java:146)
    at javax.mail.Service.connect(Service.java:297)
    at javax.mail.Service.connect(Service.java:156)
    at javax.mail.Service.connect(Service.java:105)
    at FetchMail.receive(FetchMail.java:40)
    at FetchMail.main(FetchMail.java:193)

    Hi i am trying to contact Our Zimbra server to retrieve the mails from Inbox, I used pop3 as protcol .. before but it was throwing an error
    javax.mail.AuthenticationFailedException: only valid after entering TLS mode
         at com.sun.mail.pop3.POP3Store.protocolConnect(POP3Store.java:146)
         at javax.mail.Service.connect(Service.java:297)
         at javax.mail.Service.connect(Service.java:156)
         at SampleZimbraSMTP.postMail(SampleZimbraSMTP.java:44)
         at SampleZimbraSMTP.main(SampleZimbraSMTP.java:22)
    so i changed to pop3s & downloaded new jars. I am pasting the code here
    import java.util.Date;
    import java.util.Properties;
    import javax.mail.*;
    import javax.mail.internet.*;
    import javax.mail.Authenticator;
    import javax.mail.Folder;
    import javax.mail.Message;
    import javax.mail.Multipart;
    import javax.mail.Part;
    import javax.mail.PasswordAuthentication;
    import javax.mail.Session;
    import javax.mail.Store;
    import javax.mail.Transport;
    import javax.mail.internet.InternetAddress;
    import javax.mail.internet.MimeBodyPart;
    import javax.mail.internet.MimeMessage;
    import javax.mail.internet.MimeMultipart;
    public class SampleZimbra {
         public static void main(String args[]){
              try {
                   SampleZimbra zm = new SampleZimbra();
                   zm.postMail();
         catch (Exception e) {
                   e.printStackTrace();
         private boolean debug = false;
         public void postMail() throws Exception {
              Properties props = new Properties();
              Authenticator auth = new ZimbraAuthenticator();
              Session session = Session.getDefaultInstance(props, auth);
              session.setDebug(debug);
              Store store= session.getStore("pop3s");
              store.connect("ip address","username","password");
              Folder folder = store.getFolder("INBOX");
              folder.open(Folder.READ_ONLY);
         // Get directory
         Message message[] = folder.getMessages();
         for (int i=0, n=message.length; i<n; i++) {
         System.out.println(i + ": "
         + message.getFrom()[0]
         + "\t" + message[i].getSubject());
         // Close connection
         folder.close(false);
         store.close();
    class ZimbraAuthenticator extends Authenticator {
         public PasswordAuthentication getPasswordAuthentication() {
              return new PasswordAuthentication("username", "password");
    After this code compiles & when i try to run it throw me the following error..
    javax.mail.MessagingException: Connect failed;
    nested exception is:
         javax.net.ssl.SSLHandshakeException: sun.security.validator.ValidatorException: PKIX path building failed: sun.security.provider.certpath.SunCertPathBuilderException: unable to find valid certification path to requested target
         at com.sun.mail.pop3.POP3Store.protocolConnect(POP3Store.java:148)
         at javax.mail.Service.connect(Service.java:275)
         at javax.mail.Service.connect(Service.java:156)
         at SampleZimbraSMTP.postMail(SampleZimbraSMTP.java:44)
         at SampleZimbraSMTP.main(SampleZimbraSMTP.java:22)
    Caused by: javax.net.ssl.SSLHandshakeException: sun.security.validator.ValidatorException: PKIX path building failed: sun.security.provider.certpath.SunCertPathBuilderException: unable to find valid certification path to requested target
         at com.sun.net.ssl.internal.ssl.Alerts.getSSLException(Unknown Source)
         at com.sun.net.ssl.internal.ssl.SSLSocketImpl.fatal(Unknown Source)
         at com.sun.net.ssl.internal.ssl.Handshaker.fatalSE(Unknown Source)
         at com.sun.net.ssl.internal.ssl.Handshaker.fatalSE(Unknown Source)
         at com.sun.net.ssl.internal.ssl.ClientHandshaker.serverCertificate(Unknown Source)
         at com.sun.net.ssl.internal.ssl.ClientHandshaker.processMessage(Unknown Source)
         at com.sun.net.ssl.internal.ssl.Handshaker.processLoop(Unknown Source)
         at com.sun.net.ssl.internal.ssl.Handshaker.process_record(Unknown Source)
         at com.sun.net.ssl.internal.ssl.SSLSocketImpl.readRecord(Unknown Source)
         at com.sun.net.ssl.internal.ssl.SSLSocketImpl.performInitialHandshake(Unknown Source)
         at com.sun.net.ssl.internal.ssl.SSLSocketImpl.readDataRecord(Unknown Source)
         at com.sun.net.ssl.internal.ssl.AppInputStream.read(Unknown Source)
         at java.io.BufferedInputStream.fill(Unknown Source)
         at java.io.BufferedInputStream.read(Unknown Source)
         at java.io.DataInputStream.readLine(Unknown Source)
         at com.sun.mail.pop3.Protocol.simpleCommand(Protocol.java:347)
         at com.sun.mail.pop3.Protocol.<init>(Protocol.java:91)
         at com.sun.mail.pop3.POP3Store.getPort(POP3Store.java:201)
         at com.sun.mail.pop3.POP3Store.protocolConnect(POP3Store.java:144)
         ... 4 more
    Caused by: sun.security.validator.ValidatorException: PKIX path building failed: sun.security.provider.certpath.SunCertPathBuilderException: unable to find valid certification path to requested target
         at sun.security.validator.PKIXValidator.doBuild(Unknown Source)
         at sun.security.validator.PKIXValidator.engineValidate(Unknown Source)
         at sun.security.validator.Validator.validate(Unknown Source)
         at com.sun.net.ssl.internal.ssl.X509TrustManagerImpl.checkServerTrusted(Unknown Source)
         at com.sun.net.ssl.internal.ssl.JsseX509TrustManager.checkServerTrusted(Unknown Source)
         ... 19 more
    Caused by: sun.security.provider.certpath.SunCertPathBuilderException: unable to find valid certification path to requested target
         at sun.security.provider.certpath.SunCertPathBuilder.engineBuild(Unknown Source)
         at java.security.cert.CertPathBuilder.build(Unknown Source)
         ... 24 more
    Can any one guide me to resolve this....
    Thanks
    Bharathi.
    Message was edited by:
    bharathi

  • How to set WRT54G v7 router so signal is forwardet- using bridge or repeater mode?

    What i need to set in WRT54G so its signal is beeing repeated?
    I want to use WRT54G v7 as to who internet comes in and it works like that right now and it has passw admin changed and WPA2 personal set up
    I have another router tenda w311r+ and there i have options in WDS- Lazy, Bridge and Repeater modes..
    Lazy mode is without asking BSID but others ask so i asume Lazy repeats every routers around signals..
    But what then is difference in Bridge and Repeater mode?
    I wasnt able to set all up corectly..
    Read tutorials about w311r+ and doing similar couldnt get it work..

    1
    In tenda i have
    Wifi settings
    BSSID NameTenda123 Passw123 <---- This is not same as WRT54G settings, do i need to make it like that also? Even channel the same?
    WDS settings
    Repeater ESSID Mac of WRT54G and WifipasswofWRT54G <--- this is the same as set inWRT54G
    2
    And do i connect from computer to NameTenda123 to get repeated signal from WRT54G ?
    Or the same name as reapted signal router i need to connect? BSSID of WRT54G? And do i need to set in tenda wifi settings witch now are different then WRT54G wifi settings but in Tenda WDS repeater settings are set..
    Maybe i need to set Tenda wifi off and only set WDS to be on?
    3
    Also to WRT54G i log in to 192.168.0.1 and maybe i need to set Tenda to 192.168.0.2 ? and something else?

  • Universal Repeater Mode with Airport Express

    Hi all folks,
    is something like the universal repeater mode with the new Airport Express 802.11n (2nd) available.
    Today I use a Airport Express in the Client Mode to connect to a WLAN and I connect my Mac to the Ethernet Port and the Airport is in Bridge Mode.
    This works nice and became available with the AirPort Express 802.11n, my AirPort Express 802.11g can't do this.
    On the other hand, I'm interesting in connecting some Macs to the "foreign" WLAN, but all the time I use "Join a wireless Network", I got "Internet Connection" with "Connect Using" "Wireless Network" and "Connection Sharing" "Off (Brifge Mode)" only (same with "Extend a wireless network").
    In "Participate in a WDS network" and "WDS remote" the Options for "Connection Sharing" are "Off (Bridge Mode)", "Distribute a range of IP addresses" or "Share a public IP address".
    Maybe I'm wrong, but why I can't use this "Connection Sharing" Options with "Join a wireless Network", the Client Mode, too.
    In the Bridge Mode I can't separate the two networks well.
    Any suggestions,
    Lutz

    The "Connection Sharing" option basically controls the base station's NAT & DHCP functions. By default, Connection Sharing = Share a public IP address. This would enable both NAT & DHCP. When "Distribute a range of IP addresses" is selected, DHCP is enabled, but NAT is disabled. Finally, for "Off (Bridge Mode)," both NAT & DHCP are disabled.
    Now depending on which Connection Sharing option you choose, the options for Wireless Mode will change as well. These are all pre-designed by Apple for the most common uses for their base stations for simplicity.

  • When i plug my ipod touch (4th gen) into my car usb port the ipod goes into repeat mode

    Why is it that when I plug my ipod touch into the USB port of my Peugeot 508SW that the device goes into repeat mode and the same song is played continuosly?

    Hi lllaass
    The car handbook certainly states that Ipods can be connected although it doesn't specifically mention which operating systems are supported.  The car system is recognising the ipod and playing one tune continuously but you cannot switch it to a different song.
    Geordietommo

  • How to switch repeat mode on?

    I running 11.3.1.2 on Windows 8.1 64bit.
    How to I turn on repeat mode?
    The icon/button for this is not where Apples help pages say it is!
    The only way I have found to do it is to switch on the menu bar and then go to Controls menu >> Repeat >> All.
    This if fricking crazy!
    Not to mention the fact that the Apple site is useless - I had to search just to find out how to change my password because logging in and editing profile/preferences clearly isn't it (like the rest of the internet) not Apple goes and makes a whole site just for managing your apple login with no link to it from the main site.

    I think you'll find that it's working correctly. Presumably, the programmers have decided that if you choose to manually add a song to the Up Next Playlist - then that's what you want to hear next, which is why the repeat feature is turned off. Likewise, manually adding songs to the Up Next will turn off the Shuffle feature, until the manually added songs have been played.
    Peter Row wrote:
    This is not very good; often I just throw together a few tracks that fit my mood at the time I'm playing them and have that batch playing on repeat. Yes I could save it as playlist but the simple fact of the matter is that is an extra step that I shouldn't have to do.
    Perhaps you simply need to accept that that is how it works. Surely the extra step would be worth it to you, wouldn't it?
    Of course, it's possible that you only realise that you want to hear that sequence again once it has played. In that case, there is one tip you could try. When you discover a sequence of songs that you want to hear again, look in the Songs view and list the songs by Last Played. Select the group of songs you want and then create a Playllst from that group. Note that the default view in Last Played is in reverse, as shown in this first shot:
    To put it in forward order, simply click on the Last Played column header to reverse the list, as shown in this next shot. Scroll down to the bottom of the list to find the most recent songs:
    Lastly, highlight the songs you want and either create a new Playlist from the selection or add them to an existing list:
    Yes, I know that's several steps, and you don't think you should be required to take even one extra step. The choice is yours to make, thanks to the exhaustive possibilities of iTunes.

  • WRT54G V.5 and WAP54G in "Repeater Mode" works flawlessly!

    If any of you've wondered if the combination of a Linksys WRTG54 V 5.0 Wireless Router and a Linksys WAP54G can function in "Repeater Mode". The answer is Yes. Repeater mode means to repeat your Lan wirelessly. All clients of the WAP54G are on the same network as the WRT54G i.e. 192.168.1.0 and are DHCP clients of the WRT54G.
    SSID is the same, the encryption I use is WPS-PSK with TKIP, Channel is the Same. PassPhrase is the same.
    Setup is simple just follow the User Guide with one exception. The  exception being when you configure the WAP54G in "Repeater mode" enter the "Wireless MAC address of the WRT54G router, not the "LAN" MAC address as the user guide says.
     I've extended my network to my Bro's across the street, with external antenna's ,the speed is great almost like being at home, when close to the WAP54G. One drawback is the coverage is poor except when in close proximity to the WAP54G. I'm looking into a 2.4 ghz bidirectional Wlan amplifier to hook up to the WAP54G for extending the wireless coverage.

    The WAP54G also works with the 300N wireless router.

  • More design mode problems

    I've been down this road before but now it's getting just crazy. I can't get work done if I want to create a simple layout. I've created new workspaces, cleaned, everything I can think of including taking out any third-party components that might possibly be compiled in non 4.5.1 (though they supposedly have).
    I try to create a simple MXML component. If it's based on anything visual (e.g., panel) or if I start with a group and then drag in a panel, I just get the little computer icon with red x on it in design mode with the following errors in the Design Mode Problem panel. I mean, this is just a new, empty component.
    Assets failed to compile. 
    Design Mode is unable to display the document styles, skins, and images because the following assets have failed to compile:Details
    :Unable to resolve resource bundle "components".( - Line:-1)
    Unable to resolve resource bundle "skins".( - Line:-1)
    Unable to resolve resource bundle "core".( - Line:-1)
    Unable to resolve resource bundle "core".( - Line:-1)
    Unable to resolve resource bundle "effects".( - Line:-1)
    Unable to resolve resource bundle "layout".( - Line:-1)
    Unable to resolve resource bundle "styles".( - Line:-1)
    Unable to resolve resource bundle "components".( - Line:-1)
    Unable to resolve resource bundle "core".( - Line:-1)
    Any ideas?

    I thought I had it by deleting a namespace reference; things started to render and all was good for a couple minutes. Then it reverted to the same problem so I'm open to other suggestions.

  • Music locked in repeat mode

    My music -- whether in the playlist or by album or by artist-- is locked in the repeat mode for a single song even if I touch the shuffle button. I can move it manually, but it is not scrolling through the songlist or shuffling through the list. How do I get out of this? I can't find the repeat button on the itouch, and I made sure the iTunes was on shuffle and not repeat when I synched it tonight.

    You can find this in the manual page 45.
    While playing music, tap the artwork. The scrubber bar will appear with the repeat icon and the shuffle icon. Tap the repeat icon until it is white = off.
    http://manuals.info.apple.com/enUS/iPod_touch_3.1_UserGuide.pdf

  • I installed Adobe CS6 Design & Web Premium on my Mac Book Pro a few years ago but have repeatedly encountered problems with the programs freezing or not opening properly. It's a Student and Teacher Licensing version so an academic ID is required but I am

    I installed Adobe CS6 Design & Web Premium on my Mac Book Pro a few years ago but have repeatedly encountered problems with the programs freezing or not opening properly. It's a Student and Teacher Licensing version so an academic ID is required but I am no longer a student--can I still reinstall it since my academic ID may no longer be valid?

    Erin Elzo as long as the serial number has been registered under your account at http://www.adobe.com/ then you should be able to continue to utilize the software.  You can find details on how to locate your registered serial number at Find your serial number quickly - http://helpx.adobe.com/x-productkb/global/find-serial-number.html.

Maybe you are looking for