AP 360021 cannot join WLC 5508
Dears,
I have a cisco 5508 WLC and 40 cisco 360021 APs.
I configured the WLC and assign the management interface IP and also configured a DHCP pool on my Cisco 4507 core switch wit option 43.
But the problem that the APs connot join the WLC.
The below message appears:-
Nov 7 09:08:28.953: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Nov 7 09:08:28.954: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Nov 7 09:08:38.968: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Nov 7 09:08:39.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: x.x.x.x pe6
*Nov 7 09:08:39.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
Please support me to solve this issue.
Regards,
Dears,
Also find the attched debug and the requirements that you asked for.
AP cisco debug:
*Oct 13 01:33:32.691: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Oct 13 01:33:34.691: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Oct 13 01:33:35.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Oct 13 01:33:35.691: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
*Oct 13 01:33:37.815: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Oct 13 01:33:37.903: status of voice_diag_test from WLC is false
*Oct 13 01:33:37.907: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Oct 13 01:33:37.907: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 13 01:33:38.815: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Oct 13 01:33:38.867: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Oct 13 01:33:38.875: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Oct 13 01:33:39.191: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Oct 13 01:33:39.223: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 10.10.107.58, mask 255.255.255.0, hostname APfc99.47a2.2ef7
*Oct 13 01:33:39.223: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Oct 13 01:33:39.899: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 13 01:33:40.899: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Oct 13 01:33:43.191: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Oct 13 01:33:43.259: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.10.107.58, mask 255.255.255.0, hostname APfc99.47a2.2ef7
*Oct 13 01:33:43.259: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Oct 13 01:33:47.907: %CAPWAP-3-ERRORLOG: Invalid event 29 & state 4 combination.
*Oct 13 01:33:47.907: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message. Event 29, state 4
*Oct 13 01:33:47.907: %CAPWAP-3-ERRORLOG: Failed to handle timer message.
*Oct 13 01:33:47.907: %CAPWAP-3-ERRORLOG: Failed to process timer message.
*Oct 13 01:33:48.315: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Oct 13 01:33:48.379: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to ad
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (10.10.18.1) (10.10.18.100)
ministratively down
*Oct 13 01:33:48.467: status of voice_diag_test from WLC is false
*Oct 13 01:33:48.471: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 13 01:33:49.379: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Oct 13 01:33:49.431: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Oct 13 01:33:49.439: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Oct 13 01:33:49.471: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Oct 13 01:33:49.471: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Oct 13 01:33:50.463: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 13 01:33:51.463: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Oct 13 01:33:52.475: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Oct 13 01:33:52.483: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Oct 13 01:33:53.475: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Oct 13 01:33:53.507: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 13 01:33:54.507: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 23 23:47:46.583: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
*Mar 23 23:47:46.583: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
*Mar 23 23:47:46.583: %MESH-6-LINK_UPDOWN: Mesh station fc99.47a2.2ef7 link Down
*Mar 23 23:47:47.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.10.107.5:5246
*Mar 23 23:47:48.055: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 23 23:47:48.119: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 23 23:47:48.211: status of voice_diag_test from WLC is false
*Mar 23 23:47:48.211: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 23 23:47:49.119: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 23 23:47:49.171: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 23 23:47:49.179: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 23 23:47:50.207: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 23 23:47:51.207: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 23 23:47:51.215: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 23 23:47:51.223: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 23 23:47:52.215: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 23 23:47:52.247: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 23 23:47:53.247: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.10.107.5
*Mar 24 00:25:36.579: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
*Mar 24 00:25:36.579: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
*Mar 24 00:25:36.579: %MESH-6-LINK_UPDOWN: Mesh station fc99.47a2.2ef7 link Down
APfc99.47a2.2ef7#
%CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Mar 24 00:33:27.519: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 24 00:33:28.003: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 00:33:28.035: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 00:33:28.043: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 00:33:28.051: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 00:33:29.079: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 00:33:30.079: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 24 00:33:32.519: %CAPWAP-5-SENDJOIN: sending Join Request to 10.10.107.5
*Mar 24 00:33:32.523: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 00:33:32.531: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 00:33:33.523: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 00:33:33.555: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 00:33:34.555: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radi
The Time on AP is not same time on the WLC
Oct 13 01:34:13.411: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar 24 02:02:36.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.10.107.5 peer_port: 5246
*Mar 24 02:02:36.003: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
User Access Verification
Username:
*Mar 24 02:02:36.011: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:02:37.003: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:02:37.035: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:02:38.035: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
Username:
*Mar 24 02:03:05.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2051 Max retransmission count reached!
Username: Cisco
Password:
APfc99.47a2.2ef7>
*Oct 13 01:34:13.411: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar 24 02:02:36.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.10.107.5 peer_port: 5246
*Mar 24 02:02:36.003: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
User Access Verification
Username:
*Mar 24 02:02:36.011: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:02:37.003: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:02:37.035: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:02:38.035: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
Username:
*Mar 24 02:03:05.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2051 Max retransmission count reached!
Username: Cisco
Password:
APfc99.47a2.2ef7>
*Mar 24 02:04:31.603: %IP-4-DUPADDR: Duplicate address 10.10.107.5 on BVI1, sourced by 0006.f661.d880?
memory set memory parameters
APfc99.47a2.2ef7#set
*Mar 24 02:04:33.103: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-start
*Mar 24 02:04:33.207: %CAPWAP-3-ERRORLOG: Invalid event 29 & state 4 combination.
*Mar 24 02:04:33.207: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message. Event 29, state 4
*Mar 24 02:04:33.207: %CAPWAP-3-ERRORLOG: Failed to handle timer message.
*Mar 24 02:04:33.207: %CAPWAP-3-ERRORLOG: Failed to process timer messag
APfc99.47a2.2ef7#
*Mar 24 02:04:38.159: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 24 02:04:38.223: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 24 02:04:38.315: status of voice_diag_test from WLC is false
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 24 02:04:38.315: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:04:39.223: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:04:39.275: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:04:39.283: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
%DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.10.107.5:5246
*Mar 24 02:06:58.999: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar 24 02:05:59.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.10.107.5 peer_port: 5246
*Mar 24 02:05:59.003: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:05:59.011: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:06:00.003: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:06:00.039: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:06:01.039: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
APfc99.47a2.2ef7#
APfc99.47a2.2ef7#
*Mar 24 02:09:50.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2051 Max retransmission count reached!
APfc99.47a2.2ef7#
APfc99.47a2.2ef7#
APfc99.47a2.2ef7#
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 24 02:10:20.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.10.107.5:5246
*Mar 24 02:10:21.055: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 24 02:10:21.123: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 24 02:10:21.207: status of voice_diag_test from WLC is false
*Mar 24 02:10:21.211: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:10:22.123: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:10:22.175: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:10:22.183: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:10:23.211: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:10:24.211: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 24 02:10:25.787: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
*Mar 24 02:10:25.787: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
*Mar 24 02:10:25.787: %MESH-6-LINK_UPDOWN: Mesh station fc99.47a2.2ef7 link Down
*Mar 24 02:10:30.211: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 24 02:10:30.215: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:10:30.223: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:10:31.215: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:10:31.251: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:10:32.251: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 24 02:10:49.211: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 24 02:10:49.215: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:10:49.223: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:10:50.215: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:10:50.251: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:10:51.251: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 24 02:11:08.211: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 24 02:11:08.215: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:11:08.223: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:11:09.215: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:11:09.247: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:11:10.247: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 24 02:11:16.607: %IP-4-DUPADDR: Duplicate address 10.10.107.5 on BVI1, sourced by 0006.f661.d880
*Mar 24 02:11:18.107: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 24 02:11:18.211: %CAPWAP-3-ERRORLOG: Invalid event 29 & state 4 combination.
*Mar 24 02:11:18.211: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message. Event 29, state 4
*Mar 24 02:11:18.211: %CAPWAP-3-ERRORLOG: Failed to handle timer message.
*Mar 24 02:11:18.211: %CAPWAP-3-ERRORLOG: Failed to process timer message.
*Mar 24 02:11:23.163: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 24 02:11:23.227: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 24 02:11:23.319: status of voice_diag_test from WLC is false
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 24 02:11:23.319: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:11:24.227: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:11:24.275: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:11:24.283: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:11:25.311: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:11:26.311: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 24 02:11:33.319: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 24 02:11:33.323: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:11:33.331: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:11:34.323: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:11:34.355: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:11:35.355: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 24 02:11:43.319: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar 24 02:12:43.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.10.107.5 peer_port: 5246
*Mar 24 02:12:43.003: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:12:43.011: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:12:44.003: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:12:44.035: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:12:45.035: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 24 02:17:05.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.10.107.5:5246
*Mar 24 02:17:06.055: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 24 02:17:06.119: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 24 02:17:06.203: status of voice_diag_test from WLC is false
*Mar 24 02:17:06.207: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:17:07.119: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:17:07.171: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:17:07.179: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:17:08.203: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:17:09.203: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 24 02:17:10.787: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
*Mar 24 02:17:10.787: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
*Mar 24 02:17:10.787: %MESH-6-LINK_UPDOWN: Mesh station fc99.47a2.2ef7 link Down
*Mar 24 02:17:15.207: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 24 02:17:15.211: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:17:15.219: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:17:16.211: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:17:16.247: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:17:17.247: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 24 02:17:53.207: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 24 02:17:53.211: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 24 02:17:53.219: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 24 02:17:54.211: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 24 02:17:54.247: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 24 02:17:55.247: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 24 02:18:01.607: %IP-4-DUPADDR: Duplicate address 10.10.107.5 on BVI1, sourced by 0006.f661.d880
*Mar 24 02:18:03.107: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
*Mar 24 02:18:03.207: %CAPWAP-3-ERRORLOG: Invalid event 29 & state 4 combination.
*Mar 24 02:18:03.207: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message. Even
Show requirement for AP:-
APfc99.47a2.2ef7#show version
Cisco IOS Software, C3600 Software (AP3G2-K9W8-M), Version 12.4(25e)JA, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Fri 27-Jan-12 21:27 by prod_rel_team
ROM: Bootstrap program is C3600 boot loader
BOOTLDR: C3600 Boot Loader (AP3G2-BOOT-M) LoaderVersion 12.4(23c)JY, RELEASE SOFTWARE (fc1)
APfc99.47a2.2ef7 uptime is 7 minutes
System returned to ROM by power-on
System image file is "flash:/ap3g2-k9w8-mx.124-25e.JA/ap3g2-k9w8-mx.124-25e.JA"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP3602I-A-K9 (PowerPC) processor (revision A0) with 167926K/81920K bytes of memory.
Processor board ID FGL1644Z15P
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.2.1.72
1 Gigabit Ethernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: FC:99:47:A2:2E:F7
Part Number : 73-14521-02
PCA Assembly Number : 800-37501-02
PCA Revision Number : A0
PCB Serial Number : FOC16414A83
Top Assembly Part Number : 800-35852-02
Top Assembly Serial Number : FGL1644Z15P
Top Revision Number : C0
Product/Model Number : AIR-CAP3602I-A-K9
Configuration register is 0xF
show inventry
NAME: "AP3600", DESCR: "Cisco Aironet 3600 Series (IEEE 802.11n) Access Point"
PID: AIR-CAP3602I-A-K9 , VID: V01, SN: FGL1644Z15P
show requirement on WLC
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.100.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
Build Type....................................... DATA + WPS
System Name...................................... Cisco_61:d8:84
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 10.10.107.5
Last Reset....................................... Software reset
System Up Time................................... 0 days 1 hrs 4 mins 25 secs
System Timezone Location......................... (GMT +3:00) Baghdad
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... IQ - Iraq
Operating Environment............................ Commercial (0 to 40 C)
--More-- or (q)uit
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +40 C
External Temperature............................. +24 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ 00:06:F6:61:D8:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 100
WLC after debug enable
*spamApTask6: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Discovery resp:AC Name message element length = 58
*spamApTask6: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Discovery resp: WTP Radio Information msg length = 67
*spamApTask6: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Discovery resp: CAPWAP Control IPV4 Address len = 77
*spamApTask6: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Discovery resp: CAPWAP Control IPV6 Address len = 99
*spamApTask6: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Discovery resp: Mwar type payload len = 110
*spamApTask6: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Discovery resp: Time sync payload len = 125
*spamApTask6: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Discovery Response sent to 10.10.107.60:8944
*spamApTask6: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Discovery Response sent to 10.10.107.60:8944
*spamApTask6: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 WTP already released
*spamApTask2: Mar 24 04:56:19.133: fc:99:47:a2:2e:f7 CAPWAP Control Msg Received from 10.10.107.5:8944
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 packet received of length 123 from 10.10.107.5:8944
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Msg Type = 1 Capwap state = 0
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Discovery Request from 10.10.107.5:8944
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 msgEleLength = 1 msgEleType = 20
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Total msgEleLen = 94
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 msgEleLength = 40 msgEleType = 39
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Total msgEleLen = 50
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 msgEleLength = 1 msgEleType = 41
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Total msgEleLen = 45
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 msgEleLength = 1 msgEleType = 44
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Total msgEleLen = 40
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 msgEleLength = 10 msgEleType = 37
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Vendor specific payload from AP 54:78:1A:43:CA:D0 validated
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Total msgEleLen = 26
(Cisco Controller) >*sshpmLscTask: Mar 24 05:02:01.461: sshpmLscTask: LSC Task received a message 4
*Oct 13 01:33:48.191: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
User Access Verification
Username:
Username:
Username:
*Oct 13 01:33:50.191: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Oct 13 01:33:50.191: %IP-4-DUPADDR: Duplicate address 10.10.107.5 on BVI1, sourced by 0006.f661.d880
*Oct 13 01:33:51.191: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Oct 13 01:33:52.019: %CAPWAP-3-ERRORLOG: Invalid event 29 & state 4 combination.
*Oct 13 01:33:52.019: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message. Event 29, state 4
*Oct 13 01:33:52.019: %CAPWAP-3-ERRORLOG: Failed to handle timer message.
*Oct 13 01:33:52.019: %CAPWAP-3-ERRORLOG: Failed to process timer message.
*Oct 13 01:33:53.251: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Oct 13 01:33:53.315: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to ad
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)ministratively down
*Oct 13 01:33:53.407: status of voice_diag_test from WLC is false
*Oct 13 01:33:53.411: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 13 01:33:54.315: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Oct 13 01:33:54.367: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Oct 13 01:33:54.375: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Oct 13 01:33:55.399: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Oct 13 01:33:56.399: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 msgEleLength = 22 msgEleType = 37
nable
(Cisco Controller) >*spamApTask2: Mar 24 04:56:19.133: 54:78:1a:43:ca:d0 Vendor specific payload from AP 54:78:1A:43:CA:D0 validated
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Total msgEleLen = 0
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Join Priority Processing status = 0, Incoming Ap's Priority 4, MaxLrads = 100, joined Aps =0
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 1. 0 0
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 2. 232 3
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 3. 0 0
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 4. 100 0
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Discovery resp: AC Descriptor message element len = 40
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 acName = Cisco_61:d8:84
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Discovery resp:AC Name message element length = 58
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Discovery resp: WTP Radio Information msg length = 67
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Discovery resp: CAPWAP Control IPV4 Address len = 77
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Discovery resp: CAPWAP Control IPV6 Address len = 99
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Discovery resp: Mwar type payload len = 110
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Discovery resp: Time sync payload len = 125
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Discovery Response sent to 10.10.107.5:8944
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 Discovery Response sent to 10.10.107.5:8944
*spamApTask2: Mar 24 04:56:19.134: 54:78:1a:43:ca:d0 WTP already released
*spamApTask6: Mar 24 04:56:28.440: fc:99:47:a2:2e:f7 CAPWAP Control Msg Received from 10.10.107.60:8945
*spamApTask6: Mar 24 04:56:28.440: 54:78:1a:43:ca:d0 packet received of length 123 from 10.10.107.60:8945
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Msg Type = 1 Capwap state = 0
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Discovery Request from 10.10.107.60:8945
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 1 msgEleType = 20
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 94
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 40 msgEleType = 39
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 50
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 1 msgEleType = 41
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 45
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 1 msgEleType = 44
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 40
*spamApTask7: Mar 24 04:56:28.441: fc:99:47:a2:2e:f7 CAPWAP Control Msg Received from 10.10.107.61:8945
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 10 msgEleType = 37
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 packet received of length 123 from 10.10.107.61:8945
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Vendor specific payload from AP 54:78:1A:43:CA:D0 validated
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Msg Type = 1 Capwap state = 0
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 26
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 22 msgEleType = 37
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Discovery Request from 10.10.107.61:8945
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 1 msgEleType = 20
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Vendor specific payload from AP 54:78:1A:43:CA:D0 validated
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 94
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 40 msgEleType = 39
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 0
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 50
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 1 msgEleType = 41
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Join Priority Processing status = 0, Incoming Ap's Priority 4, MaxLrads = 100, joined Aps =0
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 45
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 1 msgEleType = 44
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 1. 0 0
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 40
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 2. 232 3
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 10 msgEleType = 37
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 3. 0 0
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Vendor specific payload from AP 54:78:1A:43:CA:D0 validated
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 4. 100 0
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 26
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 msgEleLength = 22 msgEleType = 37
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Discovery resp: AC Descriptor message element len = 40
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Vendor specific payload from AP 54:78:1A:43:CA:D0 validated
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 acName = Cisco_61:d8:84
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Total msgEleLen = 0
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Discovery resp:AC Name message element length = 58
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Discovery resp: WTP Radio Information msg length = 67
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Join Priority Processing status = 0, Incoming Ap's Priority 4, MaxLrads = 100, joined Aps =0
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 1. 0 0
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 2. 232 3
*spamApTask6: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 Discovery resp: CAPWAP Control IPV4 Address len = 77
*spamApTask7: Mar 24 04:56:28.441: 54:78:1a:43:ca:d0 3. 0 0
Similar Messages
-
Cannot add WLC 5508 to Prime Infrastructure 2.1
Regards,
I've been migrating / implementing a WCS to PI 2.1. I had several problems at first to add the 11 WLC we have to PI which I could be solving by trying and testing as I have not found many references by Cisco when it comes to troubleshooting when deploying PI.
I have several queries:
1. The WCS was added 11 WLC using different SNMP communities are configured on each of them. At first when trying to add the WLC had PI SNMP communication problems. I performed the test to eliminate any of the WLC added to WCS and add it again with some communities already existing R / W without any problem. At the end, I could not add the WLC so I had to create an SNMP community with the IP of Prime in the WLC so that they can be added. Does anyone know what is the cause of this?
2. I could not add a WLC 5508 IOS 7.3 using this method, even creating an SNMP community and IP mask 0.0.0.0 / 0. No access list or FW in between the WLC These WLC are spread over several countries but i was able to add the other WLC adding a community in each WLC pointing to the IP of Prime. It is similar to this case:
https://supportforums.cisco.com/discussion/12232506/cannot-add-wlc-5508-v761200-prime-infrastructure-21
Thanks for the help.It turns out that this situation was caused by a bug in 7.6.120.0 (CSCuo73572).
TAC handed me an escalation image (7.6.120.16) that fixed this.
Added the controllers sucessfully on the first try.
Phill -
3602i CAP unable to join WLC 5508
Hi All,
Hope to you a very happy new year,
I have an (AIR-CAP3602i-E-K9) and I tried to join it to WLC 5508 but I'm facing an error,
I get this error from the LAP 1310 console as below:
Reading cookie from SEEPROM
Base Ethernet MAC address: 60:73:5c:ad:cb:9c
Boot CMD: 'boot flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx;flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx'
Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"...#####################
File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx" uncompressed and installed, entry point: 0x2003000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C3600 Software (AP3G2-RCVK9W8-M), Version 15.2(2)JA, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Thu 23-Aug-12 02:43 by prod_rel_team
Initializing flashfs...
flashfs[2]: 6 files, 3 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31997952
flashfs[2]: Bytes used: 7015936
flashfs[2]: Bytes available: 24982016
flashfs[2]: flashfs fsck took 9 seconds.
flashfs[2]: Initialization complete.
flashfs[3]: 0 files, 1 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 12257280
flashfs[3]: Bytes used: 1024
flashfs[3]: Bytes available: 12256256
flashfs[3]: flashfs fsck took 0 seconds.
flashfs[3]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Warning: the compile-time code checksum does not appear to be present.
cisco AIR-CAP3602I-E-K9 (PowerPC) processor (revision A0) with 180214K/81920K bytes of memory.
Processor board ID FCZ1642J01K
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.3.1.73
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 60:73:5C:AD:CB:9C
Part Number : 73-14521-02
PCA Assembly Number : 800-37501-02
PCA Revision Number : A0
PCB Serial Number : FOC16352BJ0
Top Assembly Part Number : 800-35852-02
Top Assembly Serial Number : FCZ1642J01K
Top Revision Number : C0
Product/Model Number : AIR-CAP3602I-E-K9
% Please define a domain-name first.
logging facility kern
^
% Invalid input detected at '^' marker.
logging trap emergencies
^
% Invalid input detected at '^' marker.
logging facility kern
^
% Invalid input detected at '^' marker.
logging trap emergencies
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
*Mar 1 00:00:10.355: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:11.971: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:12.575: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3600 Software (AP3G2-RCVK9W8-M), Version 15.2(2)JA, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Thu 23-Aug-12 02:43 by prod_rel_teamlwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:13.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:15.387: DPAA Initialization Complete
*Mar 1 00:00:15.387: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:15.979: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
no bridge-group 1 source-learning
^
% Invalid input detected at '^' marker.
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:00:32.327: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C2960S-48FPD-L (10bd.18a5.6082)
*Mar 1 00:00:48.579: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.114.42.204, mask 255.255.255.128, hostname AP6073.5cad.cb9c
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (10.114.44.129) (8.8.8.8)
*Mar 1 00:00:59.459: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.114.44.131 obtained through DHCP
*Mar 1 00:00:59.459: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:01:00.015: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:01:00.015: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'CIR906.WLC.5508'running version 7.0.235.3 is rejected.
*Mar 1 00:01:00.015: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:01:00.015: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:01:00.015: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:01:00.015: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.114.44.131
*Mar 1 00:01:10.015: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'CIR906.WLC.5508'running version 7.0.235.3 is rejected.
*Mar 1 00:01:10.015: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:01:10.015: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:01:10.015: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:01:10.015: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.114.44.131
*Mar 1 00:01:20.015: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'CIR906.WLC.5508'running version 7.0.235.3 is rejected.
*Mar 1 00:01:20.015: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:01:20.015: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:01:20.015: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:01:20.015: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.114.44.131
*Mar 1 00:01:30.015: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'CIR906.WLC.5508'running version 7.0.235.3 is rejected.
*Mar 1 00:01:30.015: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:01:30.015: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:01:30.015: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:01:30.015: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.114.44.131
*Mar 1 00:01:32.343: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C2960S-48FPD-L (10bd.18a5.6082)
*Mar 1 00:01:40.015: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'CIR906.WLC.5508'running version 7.0.235.3 is rejected.
*Mar 1 00:01:40.015: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:01:40.015: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:01:40.015: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:01:40.015: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.114.44.131
Not in Bound state.
*Mar 1 00:01:55.515: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:02:02.519: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:02:02.555: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.114.42.205, mask 255.255.255.128, hostname AP6073.5cad.cb9c
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (10.114.44.129) (8.8.8.8)
*Mar 1 00:02:06.515: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.114.44.131 obtained through DHCP
*Mar 1 00:02:06.515: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:02:06.631: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:02:06.631: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'CIR906.WLC.5508'running version 7.0.235.3 is rejected.
*Mar 1 00:02:06.631: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:02:06.631: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:02:06.631: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:02:06.631: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.114.44.131
*Mar 1 00:02:16.631: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'CIR906.WLC.5508'running version 7.0.235.3 is rejected.
*Mar 1 00:02:16.631: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:02:16.631: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:02:16.631: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:02:16.631: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.114.44.131
*Mar 1 00:02:26.631: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'CIR906.WLC.5508'running version 7.0.235.3 is rejected.
*Mar 1 00:02:26.631: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
*Mar 1 00:02:26.631: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
*Mar 1 00:02:26.631: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Mar 1 00:02:26.631: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.114.44.131
Please Advise,
Thanks in Advanced,
Ahmed,Your WLC is running a 7.0.235.3. This firmware is suitable for your 1300 but you need at least 7.2.X to run 3600.
As I've mentioned in your other thread, you can get a refurbished 4402/4404 cheap from Cisco Refurbished. You can use the 4400 to run your 1310 and the 5508 to run the newer APs. -
1310 LAP unable to join WLC 5508
Hi All,
Hope to you a very happy new year,
I have an (AIR-LAP1310G-E-K9R) and I tried to join it to WLC 5508 but I'm facing an error,
I get this error from the LAP 1310 console as below:
Compiled Mon 17-Jul-06 11:45 by alnguyen
*Mar 1 00:00:05.289: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:23.337: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:33.477: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.114.36.25, mask 255.255.255.0, hostname APe4d3.f1c2.8882
examining image...
*Mar 1 00:00:44.781: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
*Jan 11 15:21:37.178: %LWAPP-5-CHANGED: LWAPP changed state to IMAGE
%Error opening (Protocol error)archive download: takes 6 seconds
*Jan 11 15:21:43.178: LWAPP_CLIENT_ERROR_DEBUG: Retransmission count for packet exceeded more than max(IMAGE_DATA
, 1)
*Jan 11 15:21:43.178: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Jan 11 15:21:43.179: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Jan 11 15:21:43.181: LWAPP_CLIENT_ERROR: not receive read response(3)
*Jan 11 15:21:43.185: lwapp_image_proc: unable to open tar file
*Jan 11 15:21:43.200: %SYS-5-RELOAD: Reload requested by lwapp image download proc. Reload Reason: Reason unspecified.
*Jan 11 15:21:43.201: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
*Jan 11 15:21:43.207: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERYXmodem file system is available.
flashfs[0]: 3 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 7741440
flashfs[0]: Bytes used: 1861632
flashfs[0]: Bytes available: 5879808
flashfs[0]: flashfs fsck took 14 seconds.
Base ethernet MAC Address: e4:d3:f1:c2:88:82
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Loading "flash:/c1310-rcvk9w8-mx/c1310-rcvk9w8-mx"...#######################################################################################################################################################################
File "flash:/c1310-rcvk9w8-mx/c1310-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1310 Software (C1310-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:45 by alnguyen
Image text-base: 0x00003000, data-base: 0x00359EA0
Initializing flashfs...
flashfs[1]: 3 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 7741440
flashfs[1]: Bytes used: 1861632
flashfs[1]: Bytes available: 5879808
flashfs[1]: flashfs fsck took 2 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
cisco AIR-LAP1310G-E-K9R (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FGL1649T00U
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from reload
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: E4:D3:F1:C2:88:82
Part Number : 73-8960-09
PCA Assembly Number : 800-24963-06
PCA Revision Number : B0
PCB Serial Number : FOC16447J1K
Top Assembly Part Number : 800-28479-05
Top Assembly Serial Number : FGL1649T00U
Top Revision Number : D0
Product/Model Number : AIR-LAP1310G-E-K9R
Press RETURN to get started!
*Mar 1 00:00:04.329: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1310 Software (C1310-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:45 by alnguyen
*Mar 1 00:00:05.289: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.289: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:23.337: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:33.352: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.114.36.28, mask 255.255.255.0, hostname APe4d3.f1c2.8882
examining image...
*Mar 1 00:00:44.783: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
*Jan 11 15:21:37.189: %LWAPP-5-CHANGED: LWAPP changed state to IMAGE
%Error opening (Protocol error)archive download: takes 6 seconds
*Jan 11 15:21:43.189: LWAPP_CLIENT_ERROR_DEBUG: Retransmission count for packet exceeded more than max(IMAGE_DATA
, 1)
*Jan 11 15:21:43.189: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Jan 11 15:21:43.189: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Jan 11 15:21:43.192: LWAPP_CLIENT_ERROR: not receive read response(3)
*Jan 11 15:21:43.195: lwapp_image_proc: unable to open tar file
*Jan 11 15:21:43.210: %SYS-5-RELOAD: Reload requested by lwapp image download proc. Reload Reason: Reason unspecified.
*Jan 11 15:21:43.210: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
*Jan 11 15:21:43.216: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERYXmodem file system is available.
flashfs[0]: 3 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 7741440
flashfs[0]: Bytes used: 1861632
flashfs[0]: Bytes available: 5879808
flashfs[0]: flashfs fsck took 14 seconds.
Base ethernet MAC Address: e4:d3:f1:c2:88:82
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Please Advise,
Thanks in advanced,
Ahmed,Dear Stefan,
Many thanks for your kind reply,
Please find the information below:
Controller Summary
Management IP Address
10.114.44.131
Service Port IP Address
10.114.23.20
Software Version
7.2.111.3
Field Recovery Image Version
6.0.182.0
System Name
CIR906.WLC.5508
Please Advise,
Thanks,
Ahmed, -
AP Cannot join WLC, i have RADIUS authorization is pending for the AP Error
Hi Support,
I'm new in installing WIFI, I have WLC 2504 using 7.4.100.0
I have AP 1600 (AIR-CAP1602E-E-K9)
I installed the WLC and AP in a cisco poe switch, wlc and ap are in the same subnet and can ping ap from WLC, but the AP cannot join the wlc. i have this error message
(Cisco Controller) >show ap join stats detailed 00:06:f6:d6:03:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
Discovery phase statistics
- Discovery requests received.............................. 124
- Successful discovery responses sent...................... 124
- Unsuccessful discovery request processing................ 0
- Reason for last unsuccessful discovery attempt........... Not applicable
- Time at last successful discovery attempt................ Jun 11 11:56:46.133
- Time at last unsuccessful discovery attempt.............. Not applicable
Join phase statistics
- Join requests received................................... 62
- Successful join responses sent........................... 0
- Unsuccessful join request processing..................... 62
- Reason for last unsuccessful join attempt................ RADIUS authorization is pending for the AP
- Time at last successful join attempt..................... Not applicable
- Time at last unsuccessful join attempt................... Jun 11 11:56:56.606
Another this is from AP cli, i cannot have the command configure terminal
Can you please help meThanks Scott, i'm in Gabon (Central Africa) there is no Gabon in coutries list, then i chosen France.
this is the new status
(Cisco Controller) >show ap join stats detailed 00:06:f6:d6:03:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
Discovery phase statistics
- Discovery requests received.............................. 126
- Successful discovery responses sent...................... 126
- Unsuccessful discovery request processing................ 0
- Reason for last unsuccessful discovery attempt........... Not applicable
- Time at last successful discovery attempt................ Jun 11 13:38:37.411
- Time at last unsuccessful discovery attempt.............. Not applicable
Join phase statistics
- Join requests received................................... 63
- Successful join responses sent........................... 1
- Unsuccessful join request processing..................... 62
- Reason for last unsuccessful join attempt................ RADIUS authorization is pending for the AP
- Time at last successful join attempt..................... Jun 11 13:38:49.888
- Time at last unsuccessful join attempt................... Jun 11 11:56:56.606
Configuration phase statistics
--More-- or (q)uit
- Configuration requests received.......................... 0
- Successful configuration responses sent.................. 0
- Unsuccessful configuration request processing............ 0
- Reason for last unsuccessful configuration attempt....... Not applicable
- Time at last successful configuration attempt............ Not applicable
- Time at last unsuccessful configuration attempt.......... Not applicable
Last AP message decryption failure details
- Reason for last message decryption failure............... Not applicable
Last AP disconnect details
- Reason for last AP connection failure.................... Timed out while waiting for ECHO repsonse from the AP
- Last AP disconnect reason................................ Not applicable
Last join error summary
- Type of error that occurred last......................... AP got or has been disconnected
- Reason for error that occurred last...................... Timed out while waiting for ECHO repsonse from the AP
- Time at which the last join error occurred............... Jun 11 13:40:31.432
AP disconnect details
- Reason for last AP connection failure.................... Timed out while waiting for ECHO repsonse from the AP
Ethernet Mac : 00:06:f6:d6:03:f0 Ip Address : 172.25.100.84
--More-- or (q)uit
(Cisco Controller) > -
OEAP 600 cannot join WLC with auth-list enable
I've got a strange problem here. In the office, my OEAP 600 can join WLC if there is no MAC authentication. When i enable MAC authentication at WLC, AP will fail to register. However, I try it at home and it works with both MAC authentication enable or disable. I suspect it is because of firewall in my office, but there shouldn't have any different in discovery and joining procedure for AP with MAC authentication enable or disable. I'm confused here. Please help.
Justin,
Below is error summary from WLC:
Last Error Summary
Last AP Message Decryption Failure----
Last AP Connection Failure --------- Timed out while waiting for ECHO repsonse from the AP
Last Error Occurred --------- Lwapp join request rejected
Last Error Occurred Reason --------- RADIUS authorization is pending for the AP
The error reason is probaly because I haven't added AP MAC address to ACS. With the same AP, at home using ADSL link, i have no problem.
Thanks. -
Hi all,
we have two new APs 1532E and we trying to join them into the WLC.
APs received correctly Management IP address but they doesn't appear in the WLC, we got the follow error message :
*Jul 16 09:29:46.499: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Jul 16 09:29:46.499: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Jul 16 09:29:46.499: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 172.31.93.250
*Jul 16 09:29:51.499: %CAPWAP-5-SENDJOIN: sending Join Request to 172.31.93.250
*Jul 16 09:30:45.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.31.93.250:5246
*Jul 16 09:30:46.031: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Jul 16 09:30:46.079: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Jul 16 09:30:46.307: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Jul 16 09:30:56.307: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jul 16 09:30:54.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.31.93.250 peer_port: 5246
*Jul 16 09:30:54.507: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.31.93.250 peer_port: 5246
*Jul 16 09:30:54.507: %CAPWAP-5-SENDJOIN: sending Join Request to 172.31.93.250
*Jul 16 09:30:54.511: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Jul 16 09:30:54.511: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Jul 16 09:30:54.511: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Jul 16 09:30:54.511: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 172.31.93.250
*Jul 16 09:30:59.507: %CAPWAP-5-SENDJOIN: sending Join Request to 172.31.93.250
*Jul 16 09:31:53.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.31.93.250:5246
*Jul 16 09:31:54.031: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Jul 16 09:31:54.079: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Jul 16 09:31:54.307: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Jul 16 09:32:03.383: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
*Jul 16 09:32:03.383: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
*Jul 16 09:32:03.383: Mesh setting the ethernet port 0 state to 0
*Jul 16 09:32:03.383: %MESH-6-LINK_UPDOWN: Mesh station 78da.6e60.8000 link Down
*Jul 16 09:32:04.307: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jul 16 09:31:59.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.31.93.251 peer_port: 5246
*Jul 16 09:32:06.075: Mesh setting the ethernet port 0 state to 2
Do I need to change Country into the WLC? We have configured IT and US.
We tried to put into the MAC filter the Dot11radio MAC address but nothing changed.
Thanks
MarcoHi,
I had the same join problem with a new CAP1552E outdoor model which should associate with 5508 WLC or WISM. According to all information I checked before we ordered the hardware, the ios version should support this. But could not get it working.
I found this information about the country-code and the MAC address filtering.
Removed the US-country-code next to BE-code and added the MAC-address of the AP and the problem was FIXED !!!
AP joined the controller. Thanks soo much for posting this very helpfull technical information.
Belgian Network technician. -
CANNOT ADD WLC 5508 HA MODE IN PRIME INFRASTRUCTURE 2
I have two 5508 7.5.102 in HA mode and i am trying to add theme in cisco prime infrastructure 2 but i am taking back unreachable. Controller can ping the prime. I adding the controller using the management ip address of controller. Have anyone meat thise issue ? I also have problem when adding switches in stack mode (WS-C2960S-48TD-L)
Hello!
Check, that the service-port of the wlc is not in the same subnet, as Prime ip address -
Cisco CAP2602E Cannot Join WLC 2504
Dears,
I have Cisco 2504 WLC version (7.0.220.0) configured, I'm trying to join AP CAP2602 but I got error messages as shown on the attached files.
For the DNS I already created a record but still having the same eror message.
Appreciate your support,You can do a direct upgrade to 7.6MR1 from 7.0.220, this is in the matrix.
Be aware, if you use Prime Infrastructure(WCS) or MSE they too will need to be upgraded to support your WLC code. If you have these let me know and I will give you details on the upgrades I went through recently.
The APs will upgrade with the WLC. You can predownload but it sounds like your deployment is small enough to not be an issue.
Just be sure to hit the FUS upgrade while you are doing this, it is the most painful piece and will take 30-45 minutes. http://software.cisco.com/download/release.html?mdfid=283848165&softwareid=284364857&release=1.9.0.0&relind=AVAILABLE&rellifecycle=&reltype=latest -
Cannot add WLC 5508 7.2.111.3 to Cisco Prime Infrastructure 2.0
Though the Cisco Prime Infrastructure Compatibility Matrix list out that 7.2.111.3 is supported for PI 2.0
I am not able to add the controller to the PI 2.0.
The Reachability Status always shown "Unknow" and SNMP Status always shown "No response for SNMP Get".
There is no firewall between the WLC and PI.
And ping test shows it is reachable.
If I try to add controller by non-management port (I know it is not work but I want to try the reachability), the Reachability Status shown "Reachable" but the SNMP Status always shown error.
And if I use some SNMP testing software to test the SNMP port. SNMP can be quoted.
I have try to lower down the "Maximum VarBinds per Get PDU" but no luck.
Any thing I can do to troubleshoot the problem?Yes, I follow the procedure but it does not work.
Another update:
I add another WLC with version 7.0.98.0. It is fine.
And I setup another new PI 2.0 and new temporary WLC5508 with 7.2.111.3 to test. It work fine also......
So, I am wondering the existing 7.2 WLC have problem in responsing the SNMP Get. But I dont have any idea to test....
Do anyone have idea to test the snmp connection between PI and WLC? -
Cannot add WLC 5508 v7.6.120.0 into Prime Infrastructure 2.1
Hi everyone
Hope you can help us with this issue.
We already configure the WLC using this guide: http://mrncciew.com/2013/02/14/configuring-snmp-on-wlc/
snmp v2: enable
snmp v1: enable
default port values
community: incaenic with ip and mask 0.0.0.0 to allow access from any network or ip
traps receiver: community: incaenic ip: 10.100.100.15
when we try to discover the WLC with the PI it gave the error "SNMP Connectivity Fail"
WLC is on subnet 10.100.102.0/24 and PI in 10.100.100.0/24; there is a Catalyst 3850 between then with no access list on then.
Did someone can guide us with this?
Best Regards.
Alvaro RugamaHi,
Which version of SNMP are you using?
If you are using v1/v2 you should be using community string rather than local database credentials?
Regarding the service port what is the ip address assigned on the service port. From the configuration guide "Prime Infrastructure uses the preferred management IP address from the loop back interface. If the device does not have a loopback interface, Prime Infrastructure uses similar logic to the OSPF algorithm to select the router’s preferred management IP address."
Hope that helps.
Regards
Najaf -
AIR-CAP1602i cannot join a WLC 5508 controller
Hello,
I'm managing a large number of access points on a Cisco wlc 5508 controller.
We've recently purchased a bunch of new AIR-CAP1602I-E-K9.
note that we already have AIR-CAP1602I-E-K9 and other models in production.
These A.P are not able to join the controller for some reason, I've tried a lot of different things but I am now at a loss.
I have checked the regulatory domain, upgraded the FUS, manually upgraded the software version of the LAP to match the version on the other A.P.
I even downgraded/upgraded the WLC code (version 7.4.x and 8.0)
I use the dhcp option 43 to to send the controller IP.
Here are the info that can help:
errors:
#on A.P
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
#on WLC
Lwapp join request rejected (WLC version 7.6.130.0)
Failed to add database entry (WLC version 8.0)
WLC sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.6.130.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... XXX
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... XXX
Last Reset....................................... Software reset
System Up Time................................... 6 days 4 hrs 16 mins 27 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... Multiple Countries:CA,FR
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +41 C
External Temperature............................. +22 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 7
Number of Active Clients......................... 1977
Burned-in MAC Address............................ A4:93:4C:B0:E4:C0
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 250
AP sh version
AP58f3.9cb8.3701#sh version
Cisco IOS Software, C1600 Software (AP1G2-K9W8-M), Version 15.2(4)JB6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 22-Aug-14 10:56 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
AP58f3.9cb8.3701 uptime is 31 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-k9w8-mx.152-4.JB6/ap1g2-k9w8-mx.152-4.JB6"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-E-K9 (PowerPC) processor (revision B0) with 229366K/32768K bytes of memory.
Processor board ID FGL1832X5QU
PowerPC CPU at 533MHz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.6.100.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 58:F3:9C:B8:37:01
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC183171L4
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1832X5QU
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-E-K9
AP sh inventory
NAME: "AP1600", DESCR: "Cisco Aironet 1600 Series (IEEE 802.11n) Access Point"
PID: AIR-CAP1602I-E-K9 , VID: V01, SN: FGL1832X5QU
Thanks for your help !Hi Olivier,
The error messages that you have on the debugs:
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Dec 12 09:24:49.659: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
It is related to the bug: CSCuh46442
https://tools.cisco.com/bugsearch/bug/CSCuh46442/?referring_site=ss
This bug is resolved in version : 8.0.100.0
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/crn80.html#pgfId-1163951
Can you please paste here "show ap auth-list" from the controller CLI?
I suggest to enable MIC if it is not enabled, and then check if the AP's will join or not.
Kind Regards
Mohammad Setan -
Converted 1140 AP can't join the WLC 5508
Hello! Please, help me to sort my problem out.
We have bought autonomous APs AIR-AP1141N-E-K9 and converted them to the lightweight mode, but they cannot join the WLC 5508. The errors are below. There were NO problems with the LAPs that were bought before, together with the WLC.
AP's IP: 172.22.90.27 IOS version 12.4
WLC's IP: 172.22.90.20 IOS version 6.0.188.0
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
This Discussion has been converted into document:- https://supportforums.cisco.com/docs/DOC-23054
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
logs from the AP:
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Oct 13 21:37:06.044: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 13 21:37:06.045: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 13 21:37:06.046: bsnInitRcbSlot: slot 1 has NO radio
*Oct 13 21:37:06.056: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to a
dministratively down
*Oct 13 21:37:06.066: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to r
eset
*Oct 13 21:37:06.098: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Oct 13 21:37:15.060: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLL
ER
*Oct 13 21:37:24.060: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
LER
*Oct 13 21:37:34.060: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Oct 13 21:38:34.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 172.22.90.20 peer_port: 5246
*Oct 13 21:38:34.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Oct 13 21:38:34.822: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 172.22.90.20 peer_port: 5246
*Oct 13 21:38:34.823: %CAPWAP-5-SENDJOIN: sending Join Request to 172.22.90.20
*Oct 13 21:38:34.823: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Oct 13 21:38:34.825: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Contr
ol Message from 172.22.90.20
*Oct 13 21:38:34.825: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 4.
*Oct 13 21:38:34.825: %CAPWAP-3-ERRORLOG: Failed to handle capwap control messag
e from controller
*Oct 13 21:38:39.823: %CAPWAP-5-SENDJOIN: sending Join Request to 172.22.90.20
*Oct 13 21:38:39.823: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Contr
ol Message from 172.22.90.20
*Oct 13 21:38:39.823: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 4.
*Oct 13 21:38:39.823: %CAPWAP-3-ERRORLOG: Failed to handle capwap control messag
e from controller
*Oct 13 21:38:39.824: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap p
acket from 172.22.90.20
*Oct 13 21:39:33.999: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 1
72.22.90.20:5246
*Oct 13 21:39:34.000: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Oct 13 21:38:34.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 172.22.90.20 peer_port: 5246
*Oct 13 21:38:34.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Oct 13 21:38:34.001: %DTLS-5-PEER_DISCONNECT: Peer 172.22.90.20 has closed conn
ection.
*Oct 13 21:38:34.001: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 1
72.22.90.20:5246
*Oct 13 21:38:34.001: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 3 combination
*Oct 13 21:38:34.125: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
not established.
logs from the WLC:
debug capwap events enable
*Dec 21 15:02:06.244: 68:bc:0c:63:3d:a0 DTLS keys for Control Plane deleted successfully for AP 172.22.90.27
*Dec 21 15:02:06.246: 68:bc:0c:63:3d:a0 DTLS connection closed event receivedserver (172:22:90:20/5246) client (172:22:90:27/21077)
*Dec 21 15:02:06.246: 68:bc:0c:63:3d:a0 Entry exists for AP (172:22:90:27/21077)
*Dec 21 15:02:06.246: 68:bc:0c:63:3d:a0 apfSpamProcessStateChangeInSpamContext: Deregister LWAPP event for AP 68:bc:0c:63:3d:a0 slot 0
*Dec 21 15:02:06.246: 68:bc:0c:63:3d:a0 Deregister LWAPP event for AP 68:bc:0c:63:3d:a0 slot 0
*Dec 21 15:02:06.246: 68:bc:0c:63:3d:a0 apfSpamProcessStateChangeInSpamContext: Deregister LWAPP event for AP 68:bc:0c:63:3d:a0 slot 1
*Dec 21 15:02:06.246: 68:bc:0c:63:3d:a0 Deregister LWAPP event for AP 68:bc:0c:63:3d:a0 slot 1
Ble
*Dec 21 15:04:03.194: 68:bc:0c:63:3d:a0 capwap_ac_platform.c:1223 - Operation State 0 ===> 4
*Dec 21 15:04:03.194: 68:bc:0c:63:3d:a0 Register LWAPP event for AP 68:bc:0c:63:3d:a0 slot 0
*Dec 21 15:05:36.253: 68:bc:0c:63:3d:a0 Join Version: = 100711424
*Dec 21 15:05:36.253: 68:bc:0c:63:3d:a0 Join resp: CAPWAP Maximum Msg element len = 93
debug capwap errors enable
*Dec 21 16:16:51.879: 68:bc:0c:63:3d:a0 DTLS connection was closed
*Dec 21 16:17:09.940: 68:bc:0c:63:3d:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 12, joined Aps =5
debug capwap detail enable
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 CAPWAP Control Msg Received from 172.22.90.27:21078
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 packet received of length 281 from 172.22.90.27:21078
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 Msg Type = 3 Capwap state = 5
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 Join resp: Result Code message element len = 8
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 1. 47 0
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 2. 232 3
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 3. 6 0
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 4. 12 0
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 Join resp: AC Descriptor message element len = 48
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 acName = Wi-Fi_Controller
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 Join resp: AC Name message element len = 68
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 Join resp: WTP Radio Information message element len = 77
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 Join resp: CAPWAP Control IPV4 Address len = 87
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 Sending encrypted packet to AP 172:22:90:27 (21078)
*Dec 21 16:21:49.961: 68:bc:0c:63:3d:a0 Releasing WTP
*Dec 21 16:24:12.212: 68:bc:0c:63:3d:a0 CAPWAP Control Msg Received from 172.22.90.27:21077
*Dec 21 16:24:12.212: 68:bc:0c:63:3d:a0 DTLS connection 0x167c8b20 closed by controller
*Dec 21 16:24:12.212: DTL Deleting AP 9 - 0.0.0.0
*Dec 21 16:24:12.214: CAPWAP DTLS connection closed msg
*Dec 21 16:24:12.216: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'mfpSendEventReport+168' for AP 68:bc:0c:63:3d:a0(0)
*Dec 21 16:24:12.216: Received SPAM_MFP_RADIO_DOWN message
*Dec 21 16:24:12.218: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'l2roamInit+560' for AP 68:bc:0c:63:3d:a0(0)
*Dec 21 16:24:12.220: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'apfSpamCallbackInSpamContext+1224' for AP 68:bc:0c:63:3d:a0(0)
*Dec 21 16:24:12.222: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'apfSpamSendBlackListTable+376' for AP 68:bc:0c:63:3d:a0(0)
*Dec 21 16:24:12.224: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'rrmIappSendChdPacket+2320' for AP 68:bc:0c:63:3d:a0(0)
*Dec 21 16:24:12.226: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'asTrackInitTask+19360' for AP 68:bc:0c:63:3d:a0(0)
*Dec 21 16:24:12.228: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'mfpSendEventReport+168' for AP 68:bc:0c:63:3d:a0(1)
*Dec 21 16:24:12.228: Received SPAM_MFP_RADIO_DOWN message
*Dec 21 16:24:12.230: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'l2roamInit+560' for AP 68:bc:0c:63:3d:a0(1)
*Dec 21 16:24:12.232: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'apfSpamCallbackInSpamContext+1224' for AP 68:bc:0c:63:3d:a0(1)
*Dec 21 16:24:12.234: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'apfSpamSendBlackListTable+376' for AP 68:bc:0c:63:3d:a0(1)
*Dec 21 16:24:12.236: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'rrmIappSendChdPacket+2320' for AP 68:bc:0c:63:3d:a0(1)
*Dec 21 16:24:12.238: 68:bc:0c:63:3d:a0 Sending LWAPP Event DeReg to 'asTrackInitTask+19360' for AP 68:bc:0c:63:3d:a0(1)
*Dec 21 16:24:12.238: 68:bc:0c:63:3d:a0 Deleting and removing AP 68:bc:0c:63:3d:a0 from fast path
P.S. The time is set to the WLC with the NTP
P.P.S. Don't lookup at the time the logs were made - they were made not during the same day/timeI have solved this as soon as published my problem!!!
the answer is published here:
https://supportforums.cisco.com/thread/2004491
especially in the post of Matthew Fowler
Hi,
Please take a look at CSCte01087.
I see that your WLC is 10.0.13.5 and your AP is 10.0.13.28/24 so they are on the same subnet. I also see your AP MAC address does not begin with 00. This is why I believe it is relevant.
Please try the workaround or open a TAC case if you need a fix.
-Matt
Symptom:
An access point running 6.0.188.0 code may be unable to join a WLC5508.
Messages similar to the following will be seen on the AP.
%CAPWAP-3-ERRORLOG: Invalid AC Message Type 4.
%CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message
Conditions:
At least one of the following conditions pertains:
- The high order byte of the AP's MAC address is nonzero, and the AP is in
the same subnet as the WLC5508's management (or AP manager) interface
- The WLC's management (or AP manager) interface's default gateway's
MAC address' high order byte is nonzero.
Workaround:
If the MAC address of the WLC's default gateway does not begin with 00,
and if all of the APs' MAC addresses begin with 00, then: you can put
the APs into the same subnet as the WLC's management (or AP manager)
interface.
In the general case, for the situation where the WLC's default gateway's
MAC does not begin with 00, you can address this by changing it to begin
with 00. Some methods for doing this include:
-- use the "mac-address" command on the gateway, to set a MAC address
that begins with 00
-- then enable HSRP on the gateway (standby ip ww.xx.yy.zz) and use this
IP as the WLC's gateway.
For the case where the APs' MAC addresses do not begin with 00, then make
sure that they are *not* in the same subnet as the WLC's management
(AP manager) interface, but are behind a router.
Another workaround is to downgrade to 6.0.182.0. However, after
downgrading the WLC to 6.0.182.0, any APs that have 6.0.188.0 IOS
(i.e. 12.4(21a)JA2) still installed on them will be unable to join.
Therefore, after downgrading the WLC, the APs will need to have a
pre-12.4(21a)JA2 rcvk9w8 or k9w8 image installed on them.
different vlan!!!! yes! thank you Matthew Fowler sooooo much!!!! -
Hi,
I have AP :OUTDOOR,AIR-LAP1524SB-N-K9 , i want to deploy this AP at difrent location , between WLC 5508( SW:6.0.196.0) and AP there are 2 nos of layer 3 Switches
connected with OSPF.
should i use DHCP option 43 to join the AP into WLC ??
How it will work , wht configuration i need to do in Windows based DHCP server ?
Thanks
Kuldip.Hello
Yes use option 43 to point the ap toward wlc.
here are two links to help you
http://www.cisco.com/en/US/docs/wireless/access_point/1520/installation/guide/1520_axf.html#wp1007791
and
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00808714fe.shtml#p2
Cheers -
Why LAP1131AG and LAP11412 cannot to join WLC 2504?
I have WLC 2504, Cisco LAP1131AG and then Cisco LAP1142N. Why LAP1131AG and LAP11412 cannot to join WLC 2504?
this is error code at the Cisco LAP1131AG
*Sep 12 19:30:27.730: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Sep 12 19:30:27.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.100.10 peer_port: 5246
*Sep 12 19:30:57.001: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2051 Max retransmission count reached!
*Sep 12 19:31:27.000: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.100.10:5246
*Sep 12 19:31:32.083: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Sep 12 19:31:32.083: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Sep 12 19:31:32.085: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Sep 12 19:31:32.117: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 12 19:31:32.118: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 12 19:31:33.083: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Sep 12 19:31:33.112: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Sep 12 19:31:33.117: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Sep 12 19:31:34.104: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Sep 12 19:31:34.111: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Sep 12 19:31:34.142: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Sep 12 19:31:34.147: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Sep 12 19:31:34.152: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Sep 12 19:31:35.141: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Sep 12 19:31:35.146: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Sep 12 19:31:35.170: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 12 19:31:36.171: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
this is version LAP1131AG
AP0018.18fc.fd58#sh version
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(25e)JAO6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 22-Aug-14 10:07 by prod_rel_team
ROM: Bootstrap program is C1130 boot loader
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(7)JA1, RELEASE SOFTWARE (fc1)
AP0018.18fc.fd58 uptime is 9 minutes
System returned to ROM by power-on
System image file is "flash:/c1130-k9w8-mx.124-25e.JAO6/c1130-k9w8-mx.124-25e.JAO6"
and then this is version WLC2504
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.6.130.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... Cisco_47:19:c4
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 192.168.100.10
Last Reset....................................... Software reset
System Up Time................................... 0 days 0 hrs 36 mins 45 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
--More-- or (q)uit
Configured Country............................... ID - Indonesia
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +34 C
External Temperature............................. +40 C
Fan Status....................................... 4100 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Burned-in MAC Address............................ 24:E9:B3:47:19:C0
Maximum number of APs supported.................. 5
IP Address management WLC : 192.168.100.10/24
IP Address LAP1142N :192.168.100.102/24
IP Address LAP1131AG : 192.168.100.101/24
Can anyone help my problem?A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected]
cisco AIR-LAP1142N-A-K9 (PowerPC405ex) processor (revision A0) with 90102K/40960K bytes of memory.
Processor board ID FGL1439S15W
PowerPC405ex CPU at 586MHz, revision number 0x147E
Last reset from reload
LWAPP image version 7.6.130.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: C8:4C:75:79:EB:E9
Part Number : 73-12836-03
PCA Assembly Number : 800-33767-03
PCA Revision Number : A0
PCB Serial Number : FOC14234D8Z
Top Assembly Part Number : 800-33775-02
Top Assembly Serial Number : FGL1439S15W
Top Revision Number : A0
Product/Model Number : AIR-LAP1142N-A-K9
cisco AIR-LAP1131AG-A-K9 (PowerPCElvis) processor (revision A0) with 27638K/5120K bytes of memory.
Processor board ID FTX1026T46E
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 7.6.130.0
1 FastEthernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:18:18:FC:FD:58
Part Number : 73-8962-09
PCA Assembly Number : 800-24818-08
PCA Revision Number : A0
PCB Serial Number : FOC102513DE
Top Assembly Part Number : 800-25544-06
Top Assembly Serial Number : FTX1026T46E
Top Revision Number : A0
Product/Model Number : AIR-LAP1131AG-A-K9
Configuration register is 0xF
Maybe you are looking for
-
New page when the fields changed
Hi all, I wanna display my report on next when my BEZEI_T gets changed. I used at-new command also .. but its not working.. and also i want that new bezei_t get stored in some variable and change the header of the report. Please guide me. My code is
-
UNCAUGHT_EXCEPTION on load data for 0PU_C02 infocube
Hi Everybody, I am trying to load data into 0PU_C02 infocube from 0PU_O31 ODS, but the system shows me a problem in the log (ST22), the message includes: "UNCAUGHT_EXCEPTION" "CX_RSR_X_MESSAGE" "SAPLRRMS" or "LRRMSU13" "RRMS_X_MESSAGE" Thanks for you
-
Apps won't launch after disk reformat
I recently deactivated my Creative Cloud apps on my primary machine because I needed reformat the startup partition. After the reformat everytime I try to launch an app I'm asked to sign in, after the thank you screen the app will not launch (with th
-
Weblogic server is not responding
Hi Friends, I installed weblogic server 10.3 on Rec Hat Linux 5. My hardware configuration is 3 GB RAM , 150 GB hard drive, pentium 4 , DELL OPTIPLUX DX520. 32 Bit OS. I installed weblogic on this ,created a domain, and started the weblogic server. C
-
HI, I have insrtalle CLOUD this morning on my leopard (latest version) then after icloud has been installed I have downloaded lion from internet and installed it: sice preference system is quitting and impossible to retrieve my emails... What should