AP not associate with occur electrical cut

Hi
I have a different models of Access-Point, but when occur electrical cut, the ap not associate againt to controller, additional lost a domain and dns. All AP have static ip address, dns and domain.
I configure HA
Regards.

Can you explain your setup and what you did to troubleshoot. Can you provide more information and maybe post the output from the console port of the AP.
Sent from Cisco Technical Support iPhone App

Similar Messages

2702-UX-K9 Access Point will not associate with controller.

Hi,
I recently purchased nine new 2702 APs. Two of them will not associate with the controller. I realized they they had a different part number. They ended with UX-K9 instead of -K9 like the others. It turns out that these are new AP that are universal for any country. They APs find the controller but need some sort of password to pull the config down. I"m not sure what this could be?
From console of AP @ boot....
examining image...
ipv6 enable
^
% Invalid input detected at '^' marker.
ipv6 address autoconfig
^
% Invalid input detected at '^' marker.
ipv6 address dhcp
^
% Invalid input detected at '^' marker.
%Error opening capwap:/ap3g2 (Incorrect Login/Password)
Download image failed, notify controller!!! From:8.0.110.0 to 0.0.0.0, FailureCode:4
archive download: takes 0 seconds
*Mar 18 20:16:49.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.12.10 peer_port: 5246
*Mar 18 20:16:49.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.12.10 peer_port: 5246
*Mar 18 20:16:49.435: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.12.10perform archive download capwap:/ap3g2 tar file
*Mar 18 20:16:49.439: %CAPWAP-6-AP_IMG_DWNLD: Required image not found on AP. Downloading image from Controller.
*Mar 18 20:16:49.439: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.12.10:5246
*Mar 18 20:16:49.443: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 18 20:16:49.451: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 18 20:16:49.455: capwap_image_proc: unable to open tar file
*Mar 18 20:16:49.715: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
.... Check out the attached log file for more details.
Thanks in advance for the replies!

Rasika,
I have the same issue on my home 2504 with these 2700 UX, I have tried code 8.0.100.0, 8.0.110.0 (Docs say this is the min version supported), and even 8.0.115.0 (latest available) still no dice. The AP won't register, and gives the error stated above. I am seeing 2 images available for the AP, the AP shipped with the later image but I AP recovery isn't working because it say's unable to find image with XX in the name? I see the TFTP logs, and name the file accordingly no dice, then the unable to find file name -XX pops up too. As you know I am busy during the day this week, but let's jump on a skype and take a look later maybe you have seen something I haven't?
For good measure, also attempted to join a 3650 here at the house IOS-XE 3.6 no dice, going to try 3.7 too tomorrow, It worked for the 3700 UX AP's we had??

I have a lot of contacts in my phone that are not mine. In addition, my contacts are showing up on peoples devices that I do not associate with. Why is this happening?

I have a lot of contacts in my phone that are not mine. In addition, my contacts are showing up on peoples devices that I do not associate with. Why is this happening?

Hey Raffiecat,
Thanks for the question. If your iPod is setup to manually manage content, you can add content from multiple libraries:
Managing content manually on iPhone, iPad, and iPod
http://support.apple.com/kb/ht1535
When manually managing content, you can add content from multiple libraries to your iPod or iPad. Even when manually managing music, some content may be available from only one library at time. This includes all content on iPhone and video content on iPod and iPad.
You can also learn which content you can import to your new computer from your iPod:
iTunes: Transferring media from your iPhone, iPad, iPod touch, or iPod
http://support.apple.com/kb/HT1209
Or, if you still have access to the previous computer, you can transfer your iTunes Library:
iTunes: How to move your music to a new computer
http://support.apple.com/kb/HT4527
Thanks,
Matt M.

HT1849 when I download album works from itunes it does not associate with the correct artist

when I download album works from itunes it does not associate with the correct artist

Where are you looking to download them from ? You might be able to redownload them via the Purchased link under Quicklinks on the right-hand side of the iTunes store homepage on your Mac's iTunes. If that album shows there but doesn't have the cloud symbol against it for redownloading then that implies that it's still in your iTunes library

Can not associate with the access point

Greetings!
I am just new here. I am trying to set-up a wireless connection from our linksys router. I recently purchased a linksys wireless internet receiver thru USB connection. Now, my problem is the pc that is supposed to receive a wireless connection is stating " can not associate with the access point". I am not too good about computers, that is why I am seeking you help.
I hope I can hear from you guys.
Thanks in advance.
Cheers!
Square

Lets start with the bad news, no wireless connection. Good news, fixable.
Make sure all your security settings on the usb adapter are correct. If router is set for wep set adapter to wep,and so on. Also check all your firewalls, in windows, and on any virus suites that you may have running. Try turning off all firewalls, other than router, and see if that helps. Also download the easy link advisor from the linksys home page. Make sure your ssid, and network names are set the same for router, and adapter.
Stlbluesfan30
Cisco Network Academy Student

Non-root is not associate with root

I am working to setup the non-root associate with root. I have checked every configuration from the root are the same as non-root. Accept it set to non-root.
- It is the same VLAN, SSID, authentication is open. I have encryption from both sides are the same.
It is still not associated. What else should I check from the non-root to get association? Please give me some helps
I am really appreciated that.
The root configuration:
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname Root_Bridge
no logging console
aaa new-model
aaa group server radius rad_eap
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login default local
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
resource policy
clock timezone MST -7
clock save interval 24
ip subnet-zero
ip domain name Bridge
ip ssh time-out 60
ip ssh version 2
no dot11 igmp snooping-helper
dot11 vlan-name Management vlan 51
dot11 vlan-name User vlan 11
dot11 ssid LOCALBRIDGE
   vlan 51
   authentication open
   infrastructure-ssid
dot11 network-map
crypto pki trustpoint TP-self-signed-4076113752
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-4076113752
revocation-check none
rsakeypair TP-self-signed-4076113752
crypto pki certificate chain TP-self-signed-4076113752
certificate self-signed 01
30820261 308201CA A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 34303736 31313337 3532301E 170D3032 30333031 30303030
33345A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D34 30373631
31333735 3230819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100B329 87F691CA 1107EC3A 9EF4676D 2F96A7E4 42DBB88F 426D78C1 0E9E09A0
8F5EA9A1 DF88C33A A0DF128A E13E6E59 E9232487 0F5C953C 274DF314 1F48544F
E213D232 85B1E45A 4D186A9E FF9581E6 3E471891 16B627B6 CB3D8F01 BCFF89E0
77E8EA44 0E255F75 BFF1299A B3198E9B 61B3056B 8F365D98 2A8D463E F3122C47
B80D0203 010001A3 81883081 85300F06 03551D13 0101FF04 05300301 01FF3032
0603551D 11042B30 29822737 3332385F 42726964 67652E64 61766973 2D6D6F6E
7468616E 2E616363 2E64732E 61662E6D 696C301F 0603551D 23041830 1680145F
9DB7F2A6 BD563ACB 429F6938 6AF9D336 69139F30 1D060355 1D0E0416 04145F9D
B7F2A6BD 563ACB42 9F69386A F9D33669 139F300D 06092A86 4886F70D 01010405
00038181 00372387 521D029A FAE2F579 73EDCF3B FDF262EE 5DF6154E 5469A5BD
6630E5FD C8A1311A A24493D4 D1856862 8979692B CDFE65D7 29E97B60 FCC37584
A27FA332 9CC5F175 2EDC871C D41BA4F5 A50634DE 75210305 47240D4F A30D0046
532F68ED 569CE374 98C5F53D A417CFBF 3A93C98A D399B06E A73E61AB D4889452
0B695B54 86
quit
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption key 1 size 128bit 7 E99521751C16125A7754722A6B72 transmit-key
encryption key 2 size 128bit 7 1857F02303182327EA1A9242A53B
encryption key 3 size 128bit 7 FE1CF103855EBB2763224F129556
encryption key 4 size 128bit 7 19A03A5D596B029A01C208EF1C0F
encryption mode ciphers wep128
encryption vlan 11 key 1 size 128bit 7 419258EC0B7E6C7413C571760B67 transmit-key
encryption vlan 11 key 2 size 128bit 7 AB3C5B091B37223F39306B1F7442
encryption vlan 11 key 3 size 128bit 7 3E1CF103855EBB2763224F129556
encryption vlan 11 key 4 size 128bit 7 E858C5382B5D5E372A6C0438604C
encryption vlan 11 mode wep mandatory
encryption vlan 51 key 1 size 128bit 7 90792B34ACD2C8D18A0B7AF3AC68 transmit-key
encryption vlan 51 key 2 size 128bit 7 72063EA2FEF03A39E5468E92A7C5
encryption vlan 51 key 3 size 128bit 7 8607AEADB49EE0B7E4529770D9AE
encryption vlan 51 key 4 size 128bit 7 F60210B48CB39887A59255187D6D
encryption vlan 51 mode wep mandatory
ssid LOCALBRIDGE
speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
packet retries 128
station-role root
rts threshold 4000
rts retries 128
cca 87
concatenation
distance 5
beacon period 20
infrastructure-client
interface Dot11Radio0.11
encapsulation dot1Q 11
no ip route-cache
no snmp trap link-status
bridge-group 11
interface Dot11Radio0.51
encapsulation dot1Q 51 native
no ip route-cache
no snmp trap link-status
bridge-group 1
interface FastEthernet0
no ip address
no ip route-cache
hold-queue 80 in
interface FastEthernet0.11
encapsulation dot1Q 11
no ip route-cache
no snmp trap link-status
bridge-group 11
interface FastEthernet0.51
encapsulation dot1Q 51 native
no ip route-cache
no snmp trap link-status
bridge-group 1
interface BVI1
ip address 192.168.0.5 255.255.255.0
no ip route-cache
no ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
logging history informational
snmp-server view dot11view ieee802dot11 included
snmp-server community PUBLICSTRING RW
snmp-server chassis-id Bridge
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps tty
snmp-server enable traps entity
snmp-server enable traps disassociate
snmp-server enable traps deauthenticate
snmp-server enable traps authenticate-fail
snmp-server enable traps dot11-qos
snmp-server enable traps wlan-wep
snmp-server enable traps config
snmp-server enable traps syslog
snmp-server enable traps cpu threshold
snmp-server enable traps aaa_server
snmp-server enable traps envmon
snmp-server host 192.168.9.10 PUBLICSTRING
tacacs-server host 192.168.6.100
tacacs-server host 192.168.4.100
tacacs-server directed-request
radius-server attribute 32 include-in-access-req format %h
radius-server vsa send accounting
bridge 1 protocol ieee
bridge 1 route ip
line con 0
access-class 111 in
line vty 0 4
access-class 111 in
line vty 5 15
access-class 111 in
end
The non-root configuration:
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname Bridge
logging console informational
logging monitor informational
aaa new-model
aaa group server radius rad_eap
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login default local
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa cache profile admin_cache
all
aaa session-id common
resource policy
clock timezone MST -7
clock save interval 24
ip subnet-zero
ip domain name Bridge
no dot11 igmp snooping-helper
dot11 activity-timeout bridge default 3600
dot11 vlan-name Management vlan 51
dot11 vlan-name User vlan 11
dot11 ssid LOCALBRIDGE
   vlan 51
   authentication open
   infrastructure-ssid
dot11 network-map
no crypto provisioning petitioner
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption key 1 size 128bit 7 E99521751C16125A7754722A6B72 transmit-key
encryption key 2 size 128bit 7 1857F02303182327EA1A9242A53B
encryption key 3 size 128bit 7 FE1CF103855EBB2763224F129556
encryption key 4 size 128bit 7 19A03A5D596B029A01C208EF1C0F
encryption mode ciphers wep128
encryption vlan 11 key 1 size 128bit 7 419258EC0B7E6C7413C571760B67 transmit-key
encryption vlan 11 key 2 size 128bit 7 AB3C5B091B37223F39306B1F7442
encryption vlan 11 key 3 size 128bit 7 3E1CF103855EBB2763224F129556
encryption vlan 11 key 4 size 128bit 7 E858C5382B5D5E372A6C0438604C
encryption vlan 11 mode wep mandatory
encryption vlan 51 key 1 size 128bit 7 90792B34ACD2C8D18A0B7AF3AC68 transmit-key
encryption vlan 51 key 2 size 128bit 7 72063EA2FEF03A39E5468E92A7C5
encryption vlan 51 key 3 size 128bit 7 8607AEADB49EE0B7E4529770D9AE
encryption vlan 51 key 4 size 128bit 7 F60210B48CB39887A59255187D6D
encryption vlan 51 mode wep mandatory
ssid LOCALBRIDGE
speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
packet retries 128
station-role non-root bridge
rts threshold 4000
rts retries 128
cca 87
concatenation
beacon period 20
infrastructure-client
interface Dot11Radio0.11
encapsulation dot1Q 11
no ip route-cache
no snmp trap link-status
bridge-group 11
interface Dot11Radio0.51
encapsulation dot1Q 51 native
no ip route-cache
no snmp trap link-status
bridge-group 1
interface FastEthernet0
no ip address
no ip route-cache
hold-queue 80 in
interface FastEthernet0.11
encapsulation dot1Q 11
no ip route-cache
no snmp trap link-status
bridge-group 11
interface FastEthernet0.51
encapsulation dot1Q 51 native
no ip route-cache
no snmp trap link-status
bridge-group 1
interface BVI1
ip address 192.168.0.10 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
snmp-server community PUBLICSTRING RW
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps tty
snmp-server enable traps entity
snmp-server enable traps disassociate
snmp-server enable traps deauthenticate
snmp-server enable traps authenticate-fail
snmp-server enable traps dot11-qos
snmp-server enable traps wlan-wep
snmp-server enable traps config
snmp-server enable traps syslog
snmp-server enable traps cpu threshold
snmp-server enable traps aaa_server
snmp-server enable traps envmon
snmp-server host 192.168.9.10 PUBLICSTRING
tacacs-server host 192.168.6.100
tacacs-server host 192.168.4.100
tacacs-server directed-request
radius-server attribute 32 include-in-access-req format %h
radius-server vsa send accounting
bridge 1 protocol ieee
bridge 1 route ip
bridge 11 protocol ieee
line con 0
line vty 0 4
end

what happens if you go completely open, no WEP?
and I wouldn't use WEP, it's very breakable.
Steve

Photoshop cc does not associate with psd files?

I have a simple answer to the problem of photoshop cc not being able to associate psd files and not showing in the options window when you try to associate it with the psd file? How do I get it into the forum where it belongs?

Photoshop does associate with PSD and PSB files on both platforms.
It sounds like your OS is confused about the available file associations.
Which OS version are you using?

Q10 os upgrade 10.2.1.537 Wifi dos not associate with network

Hi all, have a BB Q10 and since monday have updated the OS and since then i am not able to connect to my networks at work and home. I have delated both saved networks and re done them, and it keeps telling me not able to associate with network. Can you help me? Mo

I'd recommend this Knowledge Based: Article ID: KB14477 Unable to connect to a Wi-Fi network on the BlackBerry smartphone. And also the documentation of troubleshooting wizard: http://docs.blackberry.com/en/smartphone_users/deliverables/48934/wifi.jsp
If the problem persist, it's time to call your ISP. They must know specific setting based on the router model that you are using.
Good luck.
• Click Likes to appreciate those who helps you
• If your issue solved, mark the best post in your thread as Solution

AP does not associate with WLC

the wlc send the log:
Feb 11 10:31:48.263 spam_lrad.c:1048 LWAPP-3-DISC_INTF_ERR1: Ignoring discovery request received on non-management interface (2) in L3 LWAPP mode
Any Idea? I review the network configuration and all is fine, I have 3 AP associate without problems but Im trying to add two more and send this log, from the same swithc.

The AP 1242 in this port is working fine:
interface FastEthernet3/7
switchport access vlan 105
switchport mode access
spanning-tree portfast
The AP 1242 in this port does not associate:
interface FastEthernet3/8
switchport access vlan 105
switchport mode access
spanning-tree portfast
The APs are the same and the configuration is the same but one works fine and the other dont.
any Idea?

Itunes will not associate with my music folders on an external hard drive

I moved all of my music on both libraries for two separate Ipods onto an external hard drive. Now when I open Itunes neither one of the libraries comes up. I have tried holding down the shift and choosing a library but it does not open. I am beyond frustrated, please help.

Hi, welcome to Apple Discussions.
To create or open an alternate iTunes library click the icon to start iTunes and *immediately press and _hold down_ the shift key (option for Macs)* until asked to create or choose a library. Click Choose and browse to the .itl file you want to open.
The normal layout for an iTunes library is a folder called iTunes which has some library database files in it and a folder for media called *iTunes Media* or *iTunes Music* (if created pre iTunes-9).
If you move the main iTunes folder elsewhere so that the relative path from the library to the media is unchanged then open using the shift-start-iTunes method then usually the library will carry on working as if nothing has happended.
If you just move the iTunes Media/iTunes Music folder to a new path then immediately update the iTunes preference for the location of the iTunes Media folder then sometimes it will sort itself out, but often it won't. In this case move the media folder back where it came from, open, test & close the library, then go back and move the whole iTunes folder.
If the media folder has previously been moved from inside the iTunes folder by changing the location of the media folder and then consolidating to the new location it gets more complicated. In this case the library files can usually be moved to the parent folder of the media folder, leaving the absolute path to each file unchaged but re-esatablishing the normal arrangement of library folder enclosing media folder. Once done the whole parent folder can then be renamed or moved as desired.
tt2

My iPad will not associate with iTunes, I reinstall and still get prompted to open iPad in Word, Camera or Scanner

Do i need to change my windows file association? What is the extension?

Have you selected the content to sync to your iPad in your sync settings in iTunes. The content that you want to transfer must be selected (checked or "ticked") to sync out will not transfer when you sync.
For instance - if you want to sync music....
Connect the iPad to the computer and launch iTunes.
Click on the iPad name on the left side under devices.
Click on the Music Tab on the right.
Click on the albums or playlists that you want to sync - or the entire library if you like.
Click on the Sync Music Heading.
Click on Apply in the lower right corner of iTunes
This applies to all content that you want to transfer from iTunes to your iPad. Make the selections in the appropriate tabs in the iTunes window on the right.

WRT54GC does not associate with another AP

I need to extend my WLAN and I am trying to add an AP to the WRT54GC.
The AP is of another brand (Atlantis A02-AP-W54), it works for sure (when associated to a router of its brand).
Settings are ok (same channel, ssid, wep), so what could this incompatibility be due to?
Any workaround? It seems so weird...to me...

How you have configured this Atlantis A02-AP-W54 ( Repeater / Bridge) mode. To make this A02 to work wirelessly you need to set this A02 in Bridge or Repeater mode, then only it will work wirelessly.

I just purchased Final Cut Pro X and I want to burn a dvd but the tabs do not see the option of SHARE. Is there something wrong with my Final Cut Pro X?

I just purchased Final Cut Pro X and I want to burn a dvd but the tabs do not see the option of SHARE. Is there something wrong with my Final Cut Pro X?

It's also under the File menu.

Adobe Reader does not automatically associate with PDF files in Xp Sp3

I have reinstalled Reader (twice) and it does not automatically associate with PDF files.
How do I fix this problem?
Cheers, JH

The thing is, when I right click a pdf file, and then go to properties, change default program to open with, select browse, I select it in the correct folder, when I click open, it doesnt open and the programs stay blank, so I cant select anything. There is nothing to select. And I have re-installed. But at the end of the install there are no options what file types to associate with. Any way to do it inside Reader?
I have reader 9.2.0. and Win7 up to date. When I'm opening and closing allot of files the whole time, I don't want to do inside reader. Help please?

With PS 7 create new Place two objects on the new file then you may cut copy and paste Cs2 create new place two object on the new file Cut is not available how does one cut and paste in new file

With PS 7
create new
Place two objects on the new file
then you may cut copy and paste
Cs2
create new
place two object on the new file
Cut is not available how does one cut and paste in new file

If your using File>Place then photoshop cs2 creates what's known as Smart Objects, which photoshop 7 didn't have.
In photoshop cs2 you can rasterize the smart objects and that should make the Cut function available.
Select both placed layers, right click on the area to the right of the tumbnail and select Rasterize Layers.
If in photoshop cs2 you to Help>Photoshop Help and look under Layers>Smart Objects, that should give you a good overview of what smart objects are.

AP not associate with occur electrical cut

Similar Messages

Maybe you are looking for