Ap not showing up in wlc

Hey All,
i have an AP that is not showing up in the wlc. when i place the WLC on a diffrent vlan to the WLC it shows up in the WLC but once it is placed on the same vlan to the WLC it dosnt show at all. the vlan the WLC on has spare IP's in DHCp so its not that. here is a log from wlc when that AP is not on the same Vlan:
Last AP Connection Failure -
Last Error Occurred Lwapp join request rejected
Last Error Occurred Reason Reachability info not found
client's are joinning up with the AP ( very odd??).
but once it is on the same vlan as the wlc it dosnt show up.
thanks

we are running ver:
7.0.98.0
shows up on the switch for cdp but not on the wlc ( tested in diffrent vlans)
the ap is running
AIR-LAP1231G-A-K9
also the ap has an IP in the 1 vlan but when it goes to the 10 vlan ( the vlan with the wlc on it) in cdp neighbors it still have the ip from vlan 1

Similar Messages

AP on remote site not showing up on WLC (edit)

Hi,
The AP at remote site A retrieve IP address from the FW.
From the WLC, i able to ping the IP address of the AP at remote site.
Only that on WLC, the AP at remote site not associated with the WLC.
What could be the possible reason?

hi all,
below is WLC sysinfo:
show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.5.102.0
Bootloader Version............................... 1.0.18
Field Recovery Image Version..................... 1.0.0
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... WLC_NittoDenko
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 10.154.101.104
Last Reset....................................... Power on reset
System Up Time................................... 4 days 3 hrs 36 mins 53 sec
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
--More-- or (q)uit
Configured Country............................... MY - Malaysia
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +22 C
External Temperature............................. +27 C
Fan Status....................................... 3600 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Burned-in MAC Address............................ 24:E9:B3:46:FC:A0
Maximum number of APs supported.................. 5
=========
for AP not yet, i need to go to remote site to

702W APs out of box not showing on WLC

We have a 2504 WLC with existing 11 APs which are 3602-I.
We want to add 5x more 702w APs. I have installed the license on the 2504 WLC and that was fine.
I have added new APs mac to my dhcp server, so they get an IP now and I can telnet/ssh into them using their IP (and default Cisco username/password).
The problem is that they are not showing up on the WLC. I see on the APs ssh session that its running the (ap1g1-RCVK9W8-M), Version 15.2(4)JB5, image.
Can someone please explain how I can get the APs showing up on the WLC?
Thanks in advance.

What code running on your WLC, it has to be 8.x to support this AP model. refer this
http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html
If you have compatible code on your WLC & still AP not register, pls attach AP console output while booting & trying to register
HTH
Rasika
**** Pls rate all useful responses ****

Multiple DHCP scopes on WLC 5508 (not showing leases?)

I have 2 DHCP scopes set up on a wlc 5508, one for the AP's and another for a wlan, the leases for the AP's scope show up, but the one that the clients on the WLAN are on do not show up in the "show leases" is that a bug? normal?

Customers using Cisco Unified Wireless solutions have been reporting issues with the DHCP support provided on the Wireless LAN Controller (WLC). Some of these issues are software bugs or debugability problems. Others are due to lack of proper understanding on the DHCP implementation.
This document describes the different DHCP operations on the wireless controller, which provides consistent and accurate information to customers in an effort to reduce the related customer issues and TAC cases.
Please refer to the following link: http://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/110865-dhcp-wlc.html

AP mesh info in WCS not show bridge links.

Hi guys,
I would like to know if any of you following problem has occurred. I have implemented 3 wireless mesh with 1262 AP WLC 5508 v 7.0.116.0 and WCS 7.0.172.0 base lic, all has been running perfect, the problem arises when I want to see on the map graphically bridge links, I have enabled AP Messh info but it not shows the bridge links, in hierarchical Mesh Parent-Child View only shows the RAP. To load the maps we used Campus> Outdoor area> AP.
I will appreciate any comments.
Greetings.

Are you loading 4.0? With WCS 4.x you need to generate a license with the PAK you should have received from Cisco. If you did not receive a PAK, read the following excerpt from the following url:
Existing Cisco WCS customers that have not received their PAK certificate from Cisco should contact their Cisco sales representative or send an e-mail to the [email protected] alias to notify Cisco that they need their PAK certificate. Cisco will attempt to respond to requests to this alias within 48 hours Monday-Friday 9AM-5PM Pacific Standard Time.
http://www.cisco.com/en/US/products/ps6305/products_data_sheet0900aecd804b4646.html
I hope this helps.
-Eric

MSE 8.0.110.0 not showing any clients

hi all,
i just posted a reply in some other thread stating the same thing but decided to make my own topic.
set-up:
2x5760 running 3.6.0
mse appliance running 8.0.110.0
prime infra in VM running 2.2
ap - 3702I / E
problem:
wireless clients not showing on the prime floor maps.
what have done so far:
wlc synced with mse thru nmsp - check
wlc added to prime - check
mse added to prime - check
mse synced with wlc thru prime - check
all aps positioned on the maps - check
CAS enabled on mse - check
NTP configured to wlc , mse and prime - check
check time all synced
nmsp status in mse - active
nmsp status in wlc :
WLC1#show nmsp status
MSE IP Address   Tx Echo Resp Rx Echo Req   Tx Data     Rx Data
x.x.x.x      618           618           43878       10
WLC1#show nmsp subscription sum
Mobility Services Subscribed
Server IP         Services
x.x.x.x       RSSI, Info, Statistics, AP Monitor, Attachment, Wired Location
WLC1#show nmsp subscription deta
Mobility Services Subscribed by 10.29.220.9:
Service         Subservice
RSSI            Mobile Station, Tags, Rogue
Info            Mobile Station, Rogue
Statistics      Mobile Station, Tags
Attachment      Wired Station
Location        Subscription
AP Monitor      Subscription
troubleshooting done so far:
deleted then added mse on prime then resynced to wlc
reconfigured nmsp on wlc and resynced again with mse
rebooted mse - no avail
rebooted prime - no avail
reboot wlc - not an option coz theres a lot of users =)
tia,
chris

Thanks Pete, I have done that, in fact I used a useful utility to update that property on a batch of servers.
Thanks for the thought, any additional ideas?
Cheers
Andrew

Wism controller does not show url redirection spalash page

Hi
Wism controller does not show url redirection/splash page .
client takes the ip from the dhcp server. when browsing its not going to the authentication page as usual
Thank you

Can you elaborate on your issue... really hard to follow. To me, it seems like you want to use a guest splash page. The client associates to the open guest ssid and get's an ip address. Now the user has to open a browser to get the portal page correct? This has nothing to do with the WLC, but the OS on the device. Some devices can detect if no internet is present after authentication and obtaining an address. This means the device will automatically open a browser to present the user with the splash page. Other devices will require the user to open a browser to get the login screen.
Scott

Access Points do not show in CDP neighbor

Hi All,
Last night I was performing mainteance on access points throughout the network. I was converting them from Local to H-REAP to allow for vlan support. The maintenance went well however afterwards I've noticed access points are not showing up in CDP neighbor and with a "show power inline" the access points shows as a IEEE PD. This is causing some weird issues where a client can connect but then will lose it's DHCP address. The problem happened on 9 of the 12 floors that I did this on and there is no configuration differences and bouncing the access points did not resolve the issue. The access points do show a blue light.
Has anyone ever experienced this before? If so what did you do to fix it?
I have a mix of 1131 and 1142N access points on a 4402 WLC running version 6.0.188.0.
Thank you,
Chris Pratt

The maintenance went well however afterwards I've noticed access points are not showing up in CDP neighbor and with a "show power inline" the access points shows as a IEEE PD.
I see all the time.
"sh cdp neigh" shows nothing and "sh power inline" shows the port connected to the WAP as "IEEE". This is mostly caused by faulty cabling. If you have the right Cisco switch, you can test the cable using the in-built TDR feature.
Here's how you do it:
1. Command: test cable tdr interface
2. Wait for about 5 to 7 seconds;
3. Command: sh cable tdr interface
4. Please post the complete output.

ITunes does not show up on apple tv 1st gen.

i have a 1st gen apple tv with the 160 gig HD. recently, it will not show the itunes site. Under teh movies tab there are my movies and trailers and that's it. Does anyone know how to get the itunes store back on apple tv?

Known issue currently, you'll need to wait for the fix.

My downloaded text sounds do not show up under the sounds tab in settings after installing 8.1.1. can someone help me please?

i downloaded a couple text tones and since installing 8.1.1, they will not show up under the sounds tab. in fact, they do not show up in my recent purchases on itunes, but when i go to buy them again, it says that i have already bought this tone. I just want to use the tones i paid for as the tones on my phone. not asking much.... thanks for the help. i hope someone can help me get the tones working. thank you.

This was happening to me too but only for some of my songs. I have a mac so I dunno about PCs, but for most of my ringtones I had to create an ACC version in itunes to make them short enough then turn that into a m4r and those all worked fine. But if the song was already short enough and I didn't create an ACC version and just turned the original into a m4r, then it wouldn't appear in my itunes.
so if you're on a mac:
1. go to get info, options, pick when you want the song to start and end.
     Has to be pretty short to work, 30 second or less is good
     if it's already short enough that's fine
2. right click and click 'create ACC version'
     a copy with the length you put in will appear, drag that into a folder or whatever and just type in m4r where m4a would be
     still make an ACC version even if it's the right length
Hopefully this helps someone else.

Internet Streams in Playlists do not show up on Apple TV

I use the following setup:
- Apple TV MD199LL/A (Software 6.0.1) just updated to the latest
- iTunes 11.1.3 for Windows (from a Windows 7 x64)
- iTunes 11.1.3 for MAC (from a Apple MacBook Pro x64, Maverix)
Homesharing is turned on both computers
From both machines I share pictures, videos and music.
All photos, videos and music files are getting displayed on the Apple TV menu, and can be played.
All iTunes playlists from both machines are getting displazed on the Apple TV
BUT!
If a internet stream is added to a playlist, this entry does not show on the Apple TV menu.
If the playlist contains only internet streams the Apple TV menu says "There are no songs in this library"
If I hit the play key on my remote, it will randomly play the first stream in the playlist (not realy reproducable pattern)
I can play those streams in iTunes and send it via AirPlay without problems,
Can anyone help me with this and tell me what I'm doing wrong?
Thank you

You can only view that rental on the iPad. For it to show up it has to be rented directly on ATV or through a computer and streamed via home sharing

When I sync my iPod to my MacBook through iTunes new events do not show up and old events are not deleted. I am using Snow Leopard and not iSync.

I am using Snow Leopard on a MacBook. I have an iPod touch 3G. I do not use iSync it Mobile Me. When I sync my iPod through iTunes new events on my iPod do not show up on my Mac and old events do not delete. I have read help instructions that include deleting the data on the iPod. The iPod has the correct data and the Mac does not so I have not followed those instructions. I need help as the only reason I bought the Mac was to be able to sync, back up, view and print my calendar. Currently it is useless. If only Apple could have learned from the elegance of the Palm software.

Start here:
iPhone, iPad, or iPod touch: Device not recognized in iTunes for Windows

Synced videos do not show up on iPod

Every time I sync my iPod with iTunes, although iTunes says the videos are synced, they do not show up in the Video app on the iPod.
This is a fairly new problem. All these videos have been synced before and they all showed up just fine in the Video app, but as of late the iPod does not show them. Searching for them yields no results.
The videos are in a compatible format and do not have an extremely high definition. Again, I do not think the problem is with the videos, because previously I was able to view them all just fine.
I have at least 1G of memory left, 2G without syncing the videos.
I have erased and re-synced them in iTunes, to no avail. I can play the videos on the iPod from iTunes, but not on the actual iPod device. I'm using windows iTunes, and it is up to date. The iPod software is up to date. I don't want to do a restore because I've already done that multiple times for multiple issues, but if that's what I have to do, I will. It's a pretty old iPod. I'm syncing with a third-party Duracell cable, but I really don't think that's the problem.
I'm not sure what it means, but in iTunes I have checked the option that reads, "Prefer standard definition videos". Syncing with that option unchecked changes nothing so far as I can tell.
Thanks for all your help!
iPod Touch 4th Gen. 8G
iOS 6.1.6
1G free with videos, 2G free without
iTunes for Windows 64-bit V12.1
Duracell 30 pin to USB iPod cable

Try:
- DFU mode and then restore to factory settings/new iPod via iTunes
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
- Try with a new video

Files do not show up on HDD

I tried to get an answer through the iTunes community, and was advised to try here instead as it didn't have anything directly to do with iTunes
Not all iTunes Files not showing up on External HDD
So in a nutshell, all of my 35'000 iTunes files (actual MP3 files) were saved on a TC 2.0TB disk and used on multiple Mac's to pull music from. All music files would be saved and streamed wirelessly from this TC and nowhere else.
I would always add files to this external wireless client and iTunes would work flawlessly playing whatever song I chose through the library.
If I would go in to the iTunes directory (path) and look up files on the HDD the files were just not there (but if clicking on the link through iTunes - show in finder - they would appear on the HDD but only through this method). I gave it no further thought until my TC died (i.e. no longer powers up) on me...
I removed the HDD from the TC and placed it in an USB cradle and after looking into the iTunes folder there are only a fraction of the folders / files much less than expected... When I do a cmd-I I'm told that there are 35'000 files, but they just won't show up.
Any ideas on how i can get all the files to be displayed as I want to copy these over on a new TC and need to map iTunes to this new location/path?

Hello Jfrosa,
Thank you for the details of the issue you are experiencing with File Sharing. I found an article that should help with troubleshooting this:
OS X: How to connect to Windows File Sharing (SMB) using Snow Leopard or earlier
http://support.apple.com/kb/ht1568
Thank you for using Apple Support Communities.
Best,
Sheila M.

Movie rentals that I downloaded onto iMac with Lion to do not show up on ATV 2 in menu for computers. Purchased movies show up just fine. What to do or look for?

I have an imac that is running lion and an Apple TV generation 2. I have rented a movie from itunes and it shows up on my imac in Itunes under a rental icon, and will play fine on my computer. However, it does not show up as choice to play on my apple tv. I have homesharing enabled and everything else works fine including purchased movies that are on my imac, but no where does it show rental movies.
What do I look for? What do I do to play the rental movie on my apple tv 2?

Answer to my own question:
Wait until the downloaded rental has completed its download to the imac. This took a long time for me, since it was part of several things that I was downloading at the same time.
Finally, it showed up on my apple tv. Interestingly, I was able to watch much of the movie on my iMac before the movie finished its download and was available to the ATV 2.

Ap not showing up in wlc

Similar Messages

Maybe you are looking for