AP reboot issue w/ WLC4400 and LAP1020

Hello,
I have a WiFi network based on WLC4400 (SW version 4.2.130.0) and 14 LAP1040s (SW ver. 4.2.130.0, boot ver. 2.1.78.0).
I'm experimenting AP reboots with no apparent reason (no evident correlated event which triggers the reboot).
From WLC4400 log I see messages like the following when reboots happen:
Jun 14 09:21:08.931 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:9a:2e:30 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     ECHO_REQUEST)
Jun 14 09:20:57.478 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:9a:77:d0 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     ECHO_REQUEST)
Jun 14 09:20:38.709 spam_apf.c:314 LWAPP-3-AP_DB_ERR1: Unable to find AP 00:0b:85:9a:77:d0 entry in the database, could not process delete WLAN ALL MNs message
Jun 14 09:20:38.708 spam_l2.c:760 LWAPP-3-TX_ERR3: Max retransmissions for LWAPP control message reached on AP 00:0b:85:9a:77:d0 for CONFIGURE_COMMAND (number of pending messages is 1)
Jun 14 09:19:54.694 spam_lrad.c:2630 LWAPP-3-RX_ERR9: Received a bad sequenced RRM data request message from AP 00:0b:85:9a:77:d0
Jun 14 09:19:54.109 spam_l2.c:387 LWAPP-3-RX_ERR: Received an unexpected LWAPP packet from AP 00:0b:85:9a:77:d0
Jun 14 09:15:35.261 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:9a:2e:30 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     ECHO_REQUEST)
Jun 14 09:15:23.806 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:9a:77:d0 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     ECHO_REQUEST)
Jun 14 09:15:02.698 spam_l2.c:760 LWAPP-3-TX_ERR3: Max retransmissions for LWAPP control message reached on AP 00:0b:85:9a:77:d0 for CONFIGURE_COMMAND (number of pending messages is 2)
Jun 14 09:10:00.735 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:9a:2e:30 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     ECHO_REQUEST)
Jun 14 09:09:50.089 spam_l2.c:404 LWAPP-3-RX_ERR3: Received LWAPP packet with invalid sequence number (got 1expected 2) - from AP 00:0b:85:9a:77:d0
Jun 14 09:09:50.089 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:9a:77:d0 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     ECHO_REQUEST)
Jun 14 09:09:48.369 spam_apf.c:314 LWAPP-3-AP_DB_ERR1: Unable to find AP 00:0b:85:9a:2e:30 entry in the database, could not process delete WLAN ALL MNs message
Jun 14 09:09:48.367 spam_l2.c:760 LWAPP-3-TX_ERR3: Max retransmissions for LWAPP control message reached on AP 00:0b:85:9a:2e:30 for CONFIGURE_COMMAND (number of pending messages is 1)
Jun 14 09:04:25.557 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:80:a3:c0 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     RRM_DATA_REQ)
Jun 14 09:04:25.414 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:80:a0:10 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     ECHO_REQUEST)
Jun 14 09:04:24.039 apf_rogue.c:736 APF-1-UNABLE_TO_KEEP_ROUGE_CONTAIN: Unable to keep rogue f4:ec:38:cd:a1:9e in contained state - no available AP to contain.
Jun 14 09:04:16.528 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:9a:77:d0 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     ECHO_REQUEST)
Jun 14 09:04:15.011 apf_rogue.c:736 APF-1-UNABLE_TO_KEEP_ROUGE_CONTAIN: Unable to keep rogue 54:e6:fc:e6:a2:3c in contained state - no available AP to contain.
Jun 14 09:04:03.634 spam_apf.c:314 LWAPP-3-AP_DB_ERR1: Unable to find AP 00:0b:85:80:a3:c0 entry in the database, could not process delete WLAN ALL MNs message
Jun 14 09:04:03.632 spam_l2.c:760 LWAPP-3-TX_ERR3: Max retransmissions for LWAPP control message reached on AP 00:0b:85:80:a3:c0 for CONFIGURE_COMMAND
(number of pending messages is 1)
Previous message occurred 2 times.
Jun 14 09:03:56.221 spam_lrad.c:2630 LWAPP-3-RX_ERR9: Received a bad sequenced RRM data request message from AP 00:0b:85:80:a3:c0
Jun 14 09:03:55.160 spam_lrad.c:2630 LWAPP-3-RX_ERR9: Received a bad sequenced RRM data request message from AP 00:0b:85:80:a3:c0
Jun 14 09:03:55.159 spam_lrad.c:2630 LWAPP-3-RX_ERR9: Received a bad sequenced RRM data request message from AP 00:0b:85:80:a3:c0
Previous message occurred 2 times.
Jun 14 09:03:54.174 spam_lrad.c:2630 LWAPP-3-RX_ERR9: Received a bad sequenced RRM data request message from AP 00:0b:85:80:a3:c0
Jun 14 09:03:53.151 spam_lrad.c:2630 LWAPP-3-RX_ERR9: Received a bad sequenced RRM data request message from AP 00:0b:85:80:a3:c0
Jun 14 09:03:53.150 spam_lrad.c:2630 LWAPP-3-RX_ERR9: Received a bad sequenced RRM data request message from AP 00:0b:85:80:a3:c0
Previous message occurred 2 times.
Jun 14 09:03:52.093 spam_lrad.c:2630 LWAPP-3-RX_ERR9: Received a bad sequenced RRM data request message from AP 00:0b:85:80:a3:c0
Jun 14 09:03:51.094 spam_lrad.c:2630 LWAPP-3-RX_ERR9: Received a bad sequenced RRM data request message from AP 00:0b:85:80:a3:c0
Jun 14 08:58:41.884 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:9a:77:d0 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     ECHO_REQUEST)
Jun 14 08:58:23.832 spam_l2.c:760 LWAPP-3-TX_ERR3: Max retransmissions for LWAPP control message reached on AP 00:0b:85:9a:77:d0 for CONFIGURE_COMMAND (number of pending messages is 1)
Jun 14 08:58:03.541 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:9a:81:00 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     ECHO_REQUEST)
Jun 14 08:57:57.390 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:9a:2e:30 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     RRM_DATA_REQ)
Jun 14 08:57:56.460 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:80:a3:c0 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     RRM_DATA_REQ)
Jun 14 08:57:51.925 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:80:a0:10 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     RRM_DATA_REQ)
Just before the AP reboots, a wifi client connected to that AP looses wifi connection for about 20 secs (wifi connection is ok, just no IP traffic can go through).
Can anybody help me on troubleshooting the issue?
Thanks,
Marco

I dont think it s DHCP issue, as there are no DHCP conflcts coming up.
This issue looks to be something related with the power negotiation with the AP and the switch
I did a tdr testing and the AP came up and again after a while it went down.. and the tdr testing was showing as incompleted
ATTW.IDFL15#show cable-diagnostics tdr interface gi 3/0/44
TDR test last run on: February 23 11:44:39
Interface Speed Local pair Pair length        Remote pair Pair status
Gi3/0/44  100M  Pair A     N/A                N/A         Not Completed
                Pair B     N/A                N/A         Not Completed
                Pair C     N/A                N/A         Not Completed
                Pair D     N/A                N/A         Not Completed
But I can see the Speed negiotiation done to 100M, but actually it should be 1000M.
The AP fell back to this state after TDR testing
Gi3/0/44  auto   on         15.4    Ieee PD             3     30.0
This AP was not joining the WLC and i had to console, it joined the WLC once when I plugged out the cable and plugged in. But lost the connectivity soon and I had to boot with the rcv image for the AP join the WLC
Thanks
NikhiL

Similar Messages

  • Firefox 3.6.23 having freezing and rebooting issues with Adobe Flash Player 11 Plugin

    Firefox 3.6.23 is experiencing constant freezing and rebooting issues with Adobe Flash Player 11 Plugin, not sure if it is a conflict issue or not.
    Since the update there had been no reported issues till today when the blue screen came up on me, this issue prior to plug in 11 had occurred at least 6 times, this issue only happens on firefox.
    I do not wish to update since recent firefox browsers seem to have a lot of ongoing issues.

    Anyone able to help please?
    Thanks.

  • MacBook Pro was having Finder/Freezing issues, Tried restarting and now it wont reboot. Been stuck at the apple logo/loading screen for over an hour.

    MacBook Pro was having Finder/Freezing issues, Tried restarting and now it wont reboot. Been stuck at the apple logo/loading screen for over an hour.

    Step by Step to fix your Mac
    Create a data recovery, undelete boot drive

  • Freezing and Rebooting issue - Hardware or Softwar...

    Sorry if this has been asked before...but...
    Is the freezing and rebooting issue caused by a fault in the Hardware or Software...?
    Can someone from BT please explain just exactly what is going on.
    Thank you,
    wdp

    sarahoxford wrote:
    Just been on live chat as we are fed up of freezing up, random reboots and failed recordings. Usually happens on Gold, Sky Sports - the non freeview channels. Advice from Geetesh was factory reset thus losing existing recordings, stating rather optimistically that this 'will resolve the problem'. When pushed on freezing and failed recordings issue Geetesh said recording of 'internet channels is in a test phase so won't be able to record'?? But we have recorded on gold, fox for example - response is that it won't always work, only for some customers.
    The advisor was getting confused. The bit about recording broadband channels still being in test phase only applies to BT Youview boxes. The recording functionality has been available for broadband channels on the BT Vision+ boxes since they launched last January.
    To answer the original question. The occasional freezes and reboots are caused by the New Look software (possibly in conjunction with associated system changes on the BT servers). Many of us had years of trouble free viewing using the Classic software on the same black BT Vision+ boxes. It was only when we were upgraded to the New Look software that all the troubles began. If however, you are getting such problems many times per day, or even many times per hour that could indicate a hardware fault.

  • MSI X79A GD-45 - Random Locking / Rebooting Issues

    Hi,
    I recently upgraded my old P45 chipset Q6600 16GB Hyper-V home lab server, with a nice X79A GD-45 Board, with an i3820 & 64GB of Ram.
    I've installed the system with Windows 2012, however I can't seem to get it stable.
    I have a basic AMD 4550 graphics card in the server, and Dual Port HP360T nic, 2 x LSI Raid Controllers, I have tried removing all of this, but still get the same issues.
    I have the latest BIOS updates from the MSI website.
    I found that switching the ACPI power settings to C6 in the BIOS improved the stability but it hasn't resolved the problem completely.
    I have my memory running @ 1333Mhz, as I've seen some people mention that trying to run 8x8GB @ 1600Mhz can cause problems, but that makes no difference.
    I've tried running with 32GB of Ram rather than 64GB but same issues.
    The strange thing is the PC doesn't blue screen, it sort of hangs, i.e. Windows 2012 goes un responsive, however I can still move the mouse cursor around, just nothing works, other times it just reboot's itself, and I get unexpected shutdown messages in the event logs.
    Do I have a dogdy m/board, or is there some other secret to getting the X79 boards stable, my old Q6600 on intel P45 chipset was like a rock, longest uptime was over 250 days without a reboot..
    Thanks,
    Andy.

    Hi,
    Just to let you all know that i think I had two issues in the end, the MSI commander software causing random reboots of Windows 2012, and also an old casecom 500w PSU that was causing the strange partial hangs.
    Removing MSI commander software and setting FAN control directly in BIOS stopped the random reboots, however I was still getting problems with partial crashes for example Hyper-V VM's still running but windows desktop would go unresponsive etc.. and also issues with occasional HD corruption.
    Since replacing the PSU the partial lockups / crashing have gone away, and I've had no more instances of corruption, server stable now for 80hrs+ without a reboot or weird partial hang :-)
    In addition moving to a new 80+ platinum PSU has seen the power draw to run the system drop from 38-40% of the capacity of my UPS down to 17-18% so I've halved the amount of electricity that my server uses when on 24/7, from about 200-250w down to less than 100w, just the saving of approx 2.4Kwh a day (equates to about £0.30 a day) so across the year the PSU will have paid for itself !

  • An issue with authentication and authorization on ISE 1.2

    Hi, I'm new to ISE.
    I have an issue with authentication and authorization.
    I have ISE 1.2 plus patch 6 installed on VMware.
    I have built-in Windows XP supplicant and 2960 cisco switch with IOS c2960-lanbasek9-mz.150-2.SE5.bin
    On supplicant I use EAP(PEAP) with EAP-MSCHAP v2.
    I created  authentication and authorization rules with Active Directory  as External Identity Source. Also I applied  authorization profile with DACL.I login on Windows XP machine under different Active Directory accounts. Everything works fine (authentication, authorization ), but only for several hours. After several hours passed , authentication and authorization stop working . I can see that ISE trying authenticate and authorize users, but ISE always use only one account for  authentication and authorization . Even if I login under different accounts ISE continue to use only one last account.
    I traied to reboot switch and PC,but it didn’t help. Only rebooting of ISE helps. After ISE rebooting, authentication and authorization start to work properly for several hours.
    I don’t understand is it a glitch or I misconfigured ISE or switch, supplicant?
    What  should I do to resolve this issue?
    Switch configuration:
     testISE#sh runn
    Building configuration...
    Current configuration : 7103 bytes
    ! Last configuration change at 12:20:15Tue Apr 15 2014
    ! NVRAM config last updated at 10:35:02  Tue Apr 15 2014
    version 15.0
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname testISE
    boot-start-marker
    boot-end-marker
    no logging console
    logging monitor informational
    enable secret 5 ************
    enable password ********
    username radius-test password 0 ********
    username admin privilege 15 secret 5 ******************
    aaa new-model
    aaa authentication dot1x default group radius
    aaa authorization network default group radius
    aaa authorization auth-proxy default group radius
    aaa accounting update periodic 5
    aaa accounting dot1x default start-stop group radius
    aaa server radius dynamic-author
     client 172.16.0.90 server-key ********
    aaa session-id common
    clock timezone 4 0
    system mtu routing 1500
    authentication mac-move permit
    ip dhcp snooping vlan 1,22
    ip dhcp snooping
    ip domain-name elauloks
    ip device tracking probe use-svi
    ip device tracking
    epm logging
    crypto pki trustpoint TP-self-signed-1888913408
     enrollment selfsigned
     subject-name cn=IOS-Self-Signed-Certificate-1888913408
     revocation-check none
     rsakeypair TP-self-signed-1888913408
    crypto pki certificate chain TP-self-signed-1888913408
    dot1x system-auth-control
    spanning-tree mode pvst
    spanning-tree extend system-id
    vlan internal allocation policy ascending
    ip ssh version 2
    interface FastEthernet0/5
     switchport mode access
     ip access-group ACL-ALLOW in
     authentication event fail action next-method
     authentication event server dead action reinitialize vlan 1
     authentication event server alive action reinitialize
     authentication host-mode multi-auth
     authentication open
     authentication order dot1x mab
     authentication priority dot1x mab
     authentication port-control auto
     authentication periodic
     authentication timer reauthenticate server
     authentication violation restrict
     mab
     dot1x pae authenticator
     dot1x timeout tx-period 10
     spanning-tree portfast
    interface FastEthernet0/6
     switchport mode access
     ip access-group ACL-ALLOW in
     authentication event fail action next-method
     authentication event server dead action reinitialize vlan 1
     authentication event server alive action reinitialize
     authentication order dot1x mab
     authentication priority dot1x mab
     authentication port-control auto
     authentication periodic
     authentication timer reauthenticate server
     authentication violation restrict
     mab
     dot1x pae authenticator
     dot1x timeout tx-period 10
     spanning-tree portfast
    interface FastEthernet0/7
    interface Vlan1
     ip address 172.16.0.204 255.255.240.0
     no ip route-cache
    ip default-gateway 172.16.0.1
    ip http server
    ip http secure-server
    ip access-list extended ACL-ALLOW
     deny   icmp any host 172.16.0.1
     permit ip any any
    ip radius source-interface Vlan1
    logging origin-id ip
    logging source-interface Vlan1
    logging host 172.16.0.90 transport udp port 20514
    snmp-server community public RO
    snmp-server community ciscoro RO
    snmp-server trap-source Vlan1
    snmp-server source-interface informs Vlan1
    snmp-server enable traps snmp linkdown linkup
    snmp-server enable traps mac-notification change move
    snmp-server host 172.16.0.90 ciscoro
    radius-server attribute 6 on-for-login-auth
    radius-server attribute 6 support-multiple
    radius-server attribute 8 include-in-access-req
    radius-server attribute 25 access-request include
    radius-server dead-criteria time 5 tries 3
    radius-server vsa send accounting
    radius-server vsa send authentication
    radius server ISE-Alex
     address ipv4 172.16.0.90 auth-port 1812 acct-port 1813
     automate-tester username radius-test idle-time 15
     key ******
    ntp server 172.16.0.1
    ntp server 172.16.0.5
    end

    Yes. Tried that (several times) didn't work.  5 people in my office, all with vers. 6.0.1 couldn't access their gmail accounts.  Kept getting error message that username and password invalid.  Finally solved the issue by using Microsoft Exchange and "m.google.com" as server and domain and that the trick.  Think there is an issue with imap.gmail.com and IOS 6.0.1.  I'm sure the 5 of us suddently experiencing this issue aren't the only ones.  Apple will figure it out.  Thanks.

  • I have a first generation iPad and the screen went completely green on me and locked up.  I was able to unlock it, but now there's a green haze all over the screen.  Anyone know what the issue could be and how I can get it fixed?

    I have a first generation iPad and the screen went completely green on me and locked up.  I was able to unlock it, but now there's a green haze all over the screen.  Anyone know what the issue could be and how I can get it fixed?

    Try this  - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
    Out-of-Warranty Service
         If you own an iPad that is ineligible for warranty service but is eligible for Out-of-Warranty (OOW) Service, Apple will replace (Apple doesn't repair) your iPad with an iPad that is new or equivalent to new in both performance and reliability for the Out-of-Warranty Service fee listed below. (The replacement will most likely be a refurbished iPad in a brown box, however, it has a new screen, back and battery.)   
    iPad model
    Out-of-Warranty Service Fee
    iPad mini
    $219
    iPad 3rd, 4th generation
    $299
    iPad 2, iPad
    $249
    A $6.95 shipping fee will be added if service is arranged through Apple and requires shipping. All fees are in US dollars and are subject to local tax.
    Certain damage is ineligible for out-of-warranty service, including catastrophic damage, such as the device separating into multiple pieces, and inoperability caused by unauthorized modifications. However, an iPad that has failed due to contact with liquid may be eligible for out-of-warranty service. See http://support.apple.com/kb/index?page=servicefaq&geo=United_States&product=ipad
    Make a Genius Bar Reservation
    http://www.apple.com/retail/geniusbar/
    You may can get the iPad repaired at 3rd party repair sources for less $, however, any remaining Apple warranty will be voided.
    iPad Repair & Screen Replacement Services
    http://www.ifixyouri.com/16-ipad-repairs
    RepairZoom iPad Repair
    http://www.repairzoom.com/ipad-repair.html
    Mission Repair
    http://www.missionrepair.com/Apple_iPad_Repair_Services_s/431.htm
    iGadgetResQ
    http://www.igadgetresq.com/ipad-repair/
     Cheers, Tom

  • IOS 7.0.3 did not fix the mirroring issue with ATVs and AirServer.  Anyone have an idea what needs to be done?

    iOS 7.0.3 did not fix the mirroring issue with ATVs and AirServer.  Anyone have an idea what needs to be done?  The only solution we have found is to reboot the iPad.  We don't have the option of restarting the wireless as so many people are on and it would further disrupt classes. 

    iOS 7.0.3 did not fix the mirroring issue with ATVs and AirServer.  Anyone have an idea what needs to be done?  The only solution we have found is to reboot the iPad.  We don't have the option of restarting the wireless as so many people are on and it would further disrupt classes. 

  • How do u get help from apple support with iChat? I was able to chat with support last week to solve my problem but now the same issue is back and I don't see the option to chat now?

    qHow do u get help from apple support with iChat? I was able to chat with support last week to solve my problem but now the same issue is back and I don't see the option to chat now?

    For what it is worth I have noticed a similar issue from the iPad3 while at work and home. At work we have two Apple TV 3rd Generation installed and tied to our A/V system. I believe the issue has to do with a timeout on the broadcast saying "here I am" and allowing devices to connect.
    For example:
    At work we have several Wi-Fi SSID being broadcast from Cisco APs. The only one we can use with the Apple TV is the one that uses a WEP since the others are either setup to be hidden, require web page authentication, or have a login requirement from employees. Essentially, what I believe the issue is that the Apple TV periodically broadcasts a message to other iOS devices that support Mirroring. When the Apple TV does not get a response from a device it goes into a dormant mode and requires either a command from the remote control or a reboot. This has been tested with both the power management enabled and not enabled with the same results.
    As for when I come home, the Apple TV3 has not seen the device in some time and therefore is not broadcasting it's location information. A simple click of the circle or menu keys on the remote will give it the command to start broadcasting again and allow the iPad3 to see the Apple TV. When trying to Home Share the computer can not play (iTunes 11, Win8RTM) until the Apple TV is awoken then it will show up for mirroing.
    This may or may not assist you but, it hopefully explains how the issue may be happening.

  • SAPGUI installation reboot issue

    Hello all,
    I'm experiencing the following problem on a minority of pc's after installing 7.10 pl16:
    The package installs without any problem , but when you start and try to connect to a server  you get the following message :
    before starting a sapgui session, reboot to ensure sapgui is working properly.
    despite reboots, the message stays when trying to connect.
    when you then try to uninstall sapgui, the (un)installer mentions
    "your system has a pending reboot"
    "click to reboot"
    if you reboot using this method, the tool then works.
    is there some registry entry or something that might cause this?
    the initial install is a silent no reboot install.
    kind regards
    and thanks in advance

    Any luck with this? I am using SAPGUI 7.30 / patch 1 and am equally frustrated. EVERY TIME I start NwSapSetup.exe or SapGuiSetup.exe, etc. I get the "Your system has a pending reboot!" message. I guess I could spend the rest of my life rebooting but I surely can't roll this out to my end user!. I guess I'm happy I'm not the only one with this issue but this is incredibly frustrating. And YES, I ran the nwcheckworkstation and NO, there were not any errors. (but I did get the pending reboot message there too! - aaaaaaaaaagh)

  • Galaxy s4 rebooting after last update, and freezing up

    I know this is posted already, but I too have the constant reboot issue and my s4 freezes constantly after the latest update from verizon.  My phone was flawless before, now it is basically a paperweight.  I cleared the system cache, but have not done the hard reset because many have and they say it didnt fix it whatsoever.  I dont want to waste my time losing every customization I have set up for it not to fix the problem.  I want verizon to come out and say, "We screwed up, we are trying to fix it now"  But instead, they just tell their reps to tell us to do a hard reset.  Thats the extent of their tech solving problems.  Im sick of it.  I didnt want the software, the phone was fine, now its garbage.  They forced the update to their customers and should be held liable and responsible.  I am currently paying for a service I really cant use through no fault of my own.

    I wish I could get the answer for this bc mine is doing the same thing and an update of some sort is causing my galaxy to automatically play Google play music app as soon as I go online

  • Issue with VSS and IIS

    Hello,
    At work i was handed a task for investigation and truly speaking, i dont know where to start with.
    Here is the description of the issue. You help is greatly appreciated.
    we have encountered three incidents in one month of the same type.
    Following Filesystem backup, after the Configuration backup (using DataProtector) of IIS settings, the VSS is not correctly released,
    thus impacting the following backups, resulting in dismounted databases on Exchange.
    Each time we had to reboot both the passive and active node in order to get back to nominal situation.
    I join a screenshot of the log, could you please investigate as soon as possible as it is going to cause severity 1 incidents each time
    this will happen.
    Regards,

    Hello,
    I'm unable to attach the file:
    Here is the error:
    Application - VSS 12289 10.01.2014 - 00:28:31
    Volume Shadow Copy Service error; Unexpected error VSS_E_WRITER_STATUS_NOT_AVAILABLE. An older active writer session state is being overwritten by a newer session. The most common cause is that the number of parallel backups has exceeded the maximum supported
    limit. hr=0x80042409. Operation : Aborting Writer Context: Maximum supported sessions: 64 Completed sessions: 8 Active sessions: 64 Aborted sessions: 0 Writer failed sessions: 0 New Snapshot set {1c2d4422-0181-4d24-bf05-c403c238d6b1} Old Snapshot set: {b2890d99-d486-4e1d-820a-599fb5d5be0c}
    Old Operation: 1014 Old State: 1 Old Failure: 0 Writer Class Id: {2a40fd15-dfca-4aa8-a654-1f8c654603f6} Writer Name: IIS Config Writer Writer Instance ID: {86180699-0172-47fe-b484-9a784da997ea}
    Application - VSS 12298 10.01.2014 - 00:28:31
    Volume Shadow Copy Service error: The I/O writes cannot be held during the shadow copy
    creation period on volume C:\. The volume index in the shadow copy set is 0. Error details: Open[0x00000000], Flush[0x00000000],
    Release[0x80042314],
    OnRun[0x00000000].
    Operation: Executing Asynchronous Operation Context; Current State: DoSnpshotSet
    Application - VSS 12310 10.01.2014 - 00:28:31
    Volume Shadow Copy Service error: The shadow copy could not be committed - operation timed
    out. Error context: Device IoControl(\\?\Volume.(0e61390d-d795-11df-8780-806e6f6e6963} - 00000000000001CC, 0x0053c010, 000000000002060E0, 0,00000000002050D0, 4096, [0]).
    Operation: Commiting Shadow copies context: Execution Context; System Provider

  • Rebooting Problem - Tweet @VZWSupport and let them know!

    I, like most of you on here, have been having the rebooting issue since I purchased the device. It was doing it before the OTA update and after. I suggest you guys call Verizon, or simply hit them up on twitter. The old saying goes 'the squeaky wheel gets the grease'.. WELL IT'S TIME TO  GET SQUEAKY!
    @VZWSupport
    I just tweeted them and they responded with this: 
    "I apologize. We are aware of the situation and our Network Team is working hard to resolve this issue. *CM"

    Mine reboots off and on after update but I told them. And when I'm charging it does shut off. I have the new update. After it does this then when I go into a Verizon app like NFL mobile I have to log in to my Verizon profile before I can use the app. Ugh. Does it make u sign in to if my Verizon profile after u turn the phone on as well as go into say NFL mobile or a Verizon owned app like media manager just when u start the app on. Everytime the phone turns off I have to sign in if I want to open one of these apps.

  • Since updating to iOS 7.1,  having issues with safari and wi-fi...

    Since upgrading to iOS 7.1, I have experienced issues with wifi and safari. Many websites will not load and I receive the message that "Safari cannot open the page as the server cannot be found". This only happens with the iPad (iPhone 5 is fine), and the same problems do not exist when using 3G (cellular). I have tried a reset, renewing the lease, forgetting the network, rebooting, resetting the modem... Any help would be greatly appreciated.

    Hello TunnieZee,
    Thank you for using Apple Support Communities.
    For more information, take a look at:
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/TS1398
    Unable to access the Internet while connected to Wi-Fi
    If you're using a public or commercial network, you may need to log in or subscribe.
    Check to see if you have a self-assigned IP address:
    Tap Settings > Wi-Fi and locate the Wi-Fi network to which you're connected and tap .
    If your IP address is 169.254.xxx.xxx, you may not be able to access the Internet.
    If you do not have a self-assigned IP address, see if other Wi-Fi devices on your network have Internet access.
    If they do not, consult with your network administrator or ISP for further assistance.
    If they do, reset network settings on your device by tapping Settings > General > Reset > Reset Network Settings. Note: This will reset all network settings including:
    previously connected Wi-Fi networks and passwords
    recently used Bluetooth accessories
    VPN and APN settings
    Have a nice day,
    Mario

  • Iphone 5 won't reboot. keeps flashing in and out.

    iphone 5 won't reboot. keeps flashing in and out. it is showing error 21 when I try to restore software.

    Hey Kash922,
    Thanks for using Apple Support Communities.
    Since your screen is flashing you may want to look at the hardware troubleshooting article. The error 21 is a hardware issue and is addressed in the quote from the second article.
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/TS2802
    Resolve iOS update and restore errors
    http://support.apple.com/kb/TS3694#10
    Check for hardware issues
    Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
    These errors mean that your device or computer may have a hardware issue that's preventing the update or restore from completing.
    Check that your security software and settings aren't preventing your device from communicating with the Apple update server.
    Then try to restore your iOS device two more times while connected with a cable, computer, and network you know are good.
    Confirm that your security software and settings are allowing communication between your device and update servers.
    If you still see the error message when you update or restore, contact Apple support.
    Have a nice day,
    Mario

Maybe you are looking for