Ap1130 with wlc or not?

Hello,
Is there a cli command to check whether the AP1130 is connected via a wlc ?
The cli shows the ssid's and interfaces etc. but via the webgui there are no ssids listed and it says that both radio's are up, but line protocol is down (while the current ssid's are still broadcasted)
I suspect the gui is corrupted, what may be fixed by a reboot, but currently a lot of users are connected.
I have this in CLI
dot11 ssid wifi-Gasten
   vlan 20
   authentication open
   authentication key-management wpa
   mbssid guest-mode
   wpa-psk ascii 7 0114140BE455030420420F
The ssid needs to be changed to Gasten but when I do this via CLI, the network doesn't show up anymore in the wireless networks list.
Anyone an idea?
Kind regards,
Ralph Willemsen
Arnhem, Netherlands

If the AP is in lightweight mode, there is no web UI and you can't change the SSID from the CLI.
To verify what WLC that AP is connected to, depending in what code the AP has on it:
show lwapp client rcb
or
show capwap client rcb
You would need to change the SSID from the WLC that AP is joined to.
Sent from Cisco Technical Support iPhone App

Similar Messages

Troubleshoot Cisco Airlap 1242 with WLC 4400 Series LWAPP_CLIENT_ERROR_DEBUG: spamHandleCfgReqTimer: Did not recieve the Config response

I have a Problem with my new AIRLAP 1242 to connect with WLC 4400
after debug in my airlap it shows :
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Loading "flash:/c1240-k9w8-mx.123-7.JX8/c1240-k9w8-mx.123-7.JX8"...######################################################################################################################################################################################################################################
File "flash:/c1240-k9w8-mx.123-7.JX8/c1240-k9w8-mx.123-7.JX8" uncompressed and installed, entry point: 0x3000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.3(7)JX8, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Mon 19-Mar-07 01:42 by hqluong
Image text-base: 0x00003000, data-base: 0x004051E0
Initializing flashfs...
flashfs[1]: 9 files, 3 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 5062144
flashfs[1]: Bytes available: 10936832
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
cisco AIR-LAP1242AG-E-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FCW1411U0FZ
PowerPCElvis CPU at 266Mhz, revision number 0x0950
Last reset from power-on
1 FastEthernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 68:EF:BD:5F:9A:18
Part Number                          : 73-10256-07
PCA Assembly Number                  : 800-26918-06
PCA Revision Number                  : A0
PCB Serial Number                    : FOC14093XU3
Top Assembly Part Number             : 800-29152-03
Top Assembly Serial Number           : FCW1411U0FZ
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1242AG-E-K9
Press RETURN to get started!
*Mar 1 00:00:05.608: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:06.858: %DOT11-2-VERSION_INVALID: Interface Dot11Radio0, unable to find required radio version 581.18
*Mar 1 00:00:06.858: Interface Dot11Radio0, Accepting as a test version of radio firmware
*Mar 1 00:00:06.878: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:07.234: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:08.212: %DOT11-2-VERSION_INVALID: Interface Dot11Radio1, unable to find required radio version 581.18
*Mar 1 00:00:08.212: Interface Dot11Radio1, Accepting as a test version of radio firmware
*Mar 1 00:00:08.232: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:09.278: %SYS-6-LOGGERSTART: Logger process started
*Mar 1 00:00:09.326: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.3(7)JX8, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Mon 19-Mar-07 01:42 by hqluong
*Mar 1 00:00:09.332: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Mar 1 00:00:09.388: %DOT11-6-FREQ_SCAN: Interface Dot11Radio0, Scanning frequencies for 32 seconds
*Mar 1 00:00:10.271: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:10.332: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:10.332: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:11.271: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:28.331: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:28.361: %DOT11-6-FREQ_USED: Interface Dot11Radio0, frequency 2462 selected
*Mar 1 00:00:28.362: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 1 00:00:28.363: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:28.369: %DOT11-6-FREQ_USED: Interface Dot11Radio1, frequency 5260 selected
*Mar 1 00:00:28.372: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:28.398: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:28.399: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:28.465: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:29.398: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:29.465: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
Translating "CISCO-LWAPP-CONTROLLER.ekahospital.com"...domain server (202.134.0.155)
*Mar 1 00:00:38.351: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 172.31.xxx.xxx, mask 255.255.255.0, hostname AP68ef.bd5f.9a18
*Mar 1 00:00:38.820: %DOT11-6-FREQ_USED: Interface Dot11Radio0, frequency 2417 selected
*Mar 1 00:00:38.827: %DOT11-6-FREQ_USED: Interface Dot11Radio1, frequency 5200 selected (203.130.196.5)
*Mar 1 00:00:49.835: %DOT11-6-FREQ_USED: Interface Dot11Radio0, frequency 2422 selected
*Mar 1 00:00:49.842: %DOT11-6-FREQ_USED: Interface Dot11Radio1, frequency 5220 selected
*Mar 1 00:00:49.851: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
*Mar 1 00:00:49.852: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 00:00:49.852: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Mar 1 00:00:50.852: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:50.852: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Sep 18 07:02:25.504: %LWAPP-5-CHANGED: LWAPP changed state to CFG
*Sep 18 07:02:29.288: LWAPP_CLIENT_ERROR: lwapp_name_lookup - Could Not resolve CISCO-LWAPP-CONTROLLER.MYDOMAIN.com
*Sep 18 07:02:30.504: LWAPP_CLIENT_ERROR_DEBUG: spamHandleCfgReqTimer: Did not recieve the Config response
*Sep 18 07:02:30.551: %SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: DID NOT GET CONFIG RESPONSE.
*Sep 18 07:02:30.551: %LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 5062144
flashfs[0]: Bytes available: 10936832
flashfs[0]: flashfs fsck took 26 seconds.
Base ethernet MAC Address: 68:ef:bd:5f:9a:18
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
and after that i check in my WLC that shows
AP with Base Radio MAC xx:xx:xx:xx:xx:xx (APxxxx.xxxx.xxxx) is unable to associate.
The reulatory domain configured on it '-e' does not match the controller's country
code: USA
i found that the problem about the region.
question :
1. is it possible to change the region in AIRLAP 1242 or in WLC?
2. if possible how to change it?
INFO :
my first AIRLAP Product/Model Number : AIR-LAP1242AG-A-K9 and my new AIRLAP Product/Model Number : AIR-LAP1242AG-E-K9

WLC GUI >> Wireless >> Country >> Select the country.
Regards
Surendra

WLC 2106_AP-1131_dell vostro 14 v3446 wifi not working with WLC

Hi,
I'm facing issue with newly purchased Dell laptops(dell vostro 14 v3446) are not able to join in WLC.
I have check WLAN profile for these laptops ,all mapped correct,but laptops not able to join the same profile.
Only one(newly purchased) laptop is working fine with WLC profile,remaining laptop all config is same but not getting connected with WLC.
Laptop wifi is working with another vendor APs.
But this particular profile working with my exciting user's laptop perfectly.
WLC/-AIR-WLC2106-K9-Firmware version—6.0.199.4
AP-AIR-LAP1131AG-A-K9.
Please advice me here to resolve this problem.
regards,vijesh
This was posted in lieu of blog https://supportforums.cisco.com/node/12292096 which was deleted since questions should be questions as discussions as not as blogs ;-)

Hi Leo,
Thanks for your response.
Client laptop trying to connect the SSID and once authentication key entered ,it will try for a while then error message come "could not connect...."
As our suggested,i will create new profile with open authentication,then try to connect the laptop.
we have planned to upgrade WLC firmware in coming weekend.

Connecting Cisco AIR-CAP2602E over WAN with WLC - Procedural Details

Hi,
I have a Wireless LAN Controller Installed in one of the subnets where some AIR-CAP2602E's are connected with the WLC. WLC acts as DHCP for the AIR-CAP2602E Devices.
I have additional AIR-CAP2602E access-points at other location (Subnet) and Need to connect them with WLC.
Challange faced by me is creating DHCP on Cisco 2950 (L2) or 3750 (L3) with DHCP option 43. Can any one has detailed configuration of enabling DHCP for specific VLAN on Cisco L2 and L3 Devices.

If you have control of the DNS environment for these network segments, just make an entry for :
cisco-lwapp-controller aliases cisco-capwap-controller (IP list) as the CAP will hunt for those two name sets.
My WLC provides DHCP support only to the wlans supported by the AP but not the AP it self..
hope this helps

ISE device registration webauth with wlc 7.0 lwa

Is it possible to use the DRW feature with WLCs running 7.0 code? All configuration examples refer to 7.2 code. Its only for guest user device registration. No profiling / provisioning.
Compatibility matrix says that "Wireless Controllers support MAC filtering with RADIUS lookup. For WLCs that support version 7.2.103.0, there is support for session ID and COA with MAC filtering so it is more MAB-like."
Thanks.

Hi,
The reason you need to run the upgraded code is that the radius NAC feature coupled with a mac-filtering enabled SSID will work together. On the release prior you were unable to get both features to work with one another.
For your reference here is the item in the New Features section of the 7.2 WLC release notes:
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn7_2.html#wp855314
thanks,
Tarik Admani
*Please rate helpful posts*

7925 Phones voice quality issues with wlc 5508 version 7.6

Hi all,
I have a mix environment with 1 WLC 5508 and more or less 6 sites with several Access Points ( all AIR-LAP1242AG and all in FlexConnect mode Hreap ) and several wireless phones (all CP7925G) . My Ap's have antennas 2.4GHz in all sites except 1 site ( the one i'm talking for now) with 2.4GHz and 5GHz , because of the problems we suggest to have all phone in A BAND (5Ghz) . In this site we force the phones just to A (802.11a only) , power safe NONE , Continuous scan mode , i fallow all in http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/7925g/7_0/english/deployment/guide/7925dply.pdf , one thing i didn’t do it was apply QoS because I can’t apply several ios commands in that 2960 with lan lite ios.
So I have 3 SSID for data and 2 for VOICE ( one is common to all environment and supports 2.4 and 5Ghz , and other just to test one site , with only 5Ghz with “[WPA2][Auth(802.1X + CCKM)][Auth(FT 802.1X)]”, because I read that problem can be phone rooming , and in FlexConnect only have fast-roaming in a CCKM or a PKM key-management solution , but even like this the problem still exist) .
I have another sites with phones in 2.4GHz running well and others with problems.
i read here in forums lots and lots of people with similar problems , i tried several solutions ( WLC upgrades versions and phones firmware's , …. ) tried all my best of solving the problems mas now I’m running without any ideas , i did also some site surveys and detect some interferers that why I change phones to 5Ghz , and I run also WLC Config analyser to help me , but all without good success. Some changes solve temporarily problems , but after some time , people reclaim about problems.
I can open a TAC case but first I want be sure if did all already.
Can someone try to help me?
ip phone 7925G firmware : CP7925G-1.4.5SR1.3
CUCM 8.6.2
WLC    5508 : 7.6.120.0
AP : AIR-LAP1242AG-E-K9    7.6.120.0       (flexconnect)
Best Regards

Hi Serge,
Thanks for the suggestions. I have taken care of all the settings. Problem is , the user is seated in his office cabin and using the 7925 and there is around 50db signal strength in his room from an AP which is just outside the cabin. And this doesnt occur often, when we go to check and make calls, everything is fine whereas the user says it happens sometimes in the morning, evening etc... randomly... where the fone goes blank while in a call.... since the problem never happens when we go to troubleshoot the issue, we really dont know what is going on. This is happening when calling PSTN.
AP's are not restarting and there is no logs indicating that. Wireless infrastructure looks very much OK cos there are other users who are not experiencing this problem and there is ample coverage all over the floor. I am baffled why only one user has this problem even when he is seated in his office cabin.
Tried changing phones also, but still remains.
Question : i tried to do a linktest from WLC to his phone, but it failed, while linktest to laptops are working fine. Does wlc linktest not working for wireless phones ?
regards
Joe

An issue with WLC 5508 and 7921 phone

Hello all!
I have a system with WLC 5508 and some 1242 APs. And I use a lot of 7921 phones.
One of 7921 phones was in trouble. It loses registration, disconnect conversations...
I installed the trial WLC and run voice diagnostics.
I saw some of "Potentially degraded QoS in downlink direction because of incorrect packet classification" messages and one "Fair upstream packet loss ratio: 1,2%, which is less than threshold 2.5%"
As I understand all of 7921 phones in these area are affected.
what does it mean? I set up Platinum QoS for voice WLAN. I don't have any qos configuration string for AP and WLC ports on switches...
any ideas?
thanx in advance

Sergey:
There is one application called "WLC Config analyzer". You save your "show run-config" from your WLC in a text file and import it by this application. it will analyze the file for you and tell you what recommendations for voice are missing so you improve them.
When importing a config file you choose what voice clinets you are using, so you need to choose cisco 7921 to it tells you what config improvemetns is needed based on 7921 needs.
Here is the link to download the application:
https://supportforums.cisco.com/docs/DOC-1373
download the latest versoin.
BTW, how many voice/data clients are connected to one AP in that area? if I remember correctly if you are utilizing voice then the max number of clients connected to one AP should not exceed 17. If you have more than this number per AP try to minimize the number of users concurrently connected to the AP then try again.
Hope you'll find the config analyzer useful.
If useful please don't forget to rate.
Amjad

WLC 5508 - AP's are conecting with WLC but unable to regester with WLC

Hi,
I have old 4400 series wlc and recently I have configured 5508 wlc and 6 new Access Point.
when you go to MONITER - AP Join their it shows connected AP detail with AP IP address but if u see it in under WIRELESS Option their is not showing any AP's detail.
I mean to say that AP's are connecting with WLC and also getting IP address but unable to regester with WLC.
Even I have checked with remove Radius configuration also from wlc as well as from acs.
please suggest......

Im not able to post info it says below msg, plesse suggest how i can provide detail.
This message can not be displayed due to its content. Please use the contact us link with any questions.
Also I like to say that after factory rest 4 out of 6 is done now 2 remain.

AP 1310 with WLC 5508

Hi,
I have upgraded my WLC 5508 from 7.0 to 7.4 and the AP 1310 no longer can associate to WLC.
Seems that the AP doesn't work with WLC ver 7.4
Except changing these APs to autonomous mode, any other alternatives?
Besides, if we change them to autonomous mode, can Prime Infrastructure manage/monitor these APs?
thanks.

The 1310 last support is on v7.0.x of the WLC. See the matrix below.
http://www.cisco.com/en/US/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html
Prime Infrastructure can monitor the Autonomous access point but will not do anything else than monitor. Config changes is done via the bridge/AP itself.
Sent from Cisco Technical Support iPhone App

WLC 4400 Not authetnicating between GUEST and Private networks

Hello,
I have a problem. I have a WLC 4400 and the problem i´m encountering is that when a user authetnicates to the private network, and then tryies to autheticate to the Guest network, it just stays there, it doens't do anything. Same way around, if you authenticate tothe Guest network, and change to the private network, it just sits there. I pointing that the problem is with Authentication, but not sure if i´m correct.
Can anyone help me?? what ifnormation will i need to retreive from the WLC to see where the problem lies??
I will get the debug mac addr <client-MAC-address xx:xx:xx:xx:xx:xx> and repeat the issue in order to see if i get anything from the client.
Thanks for the help
Tony

Thanks for the help.
Actually the problem was that the WLC had a wrong time and also we had on our DHCP a 24 hour lease, so we were running low on IP´s.
Change the lease for 8 hours and set the time correctly and the issue got solved.
Thanks.

Help me : Problem with WLC and AP

Hi,
We have a few AP on our network which work fine.
But, those which are behind our fw don't work.
LAN WI-FI with WLC <>--------Lan Routed---with Ap (Ok) ------------------
<> -------FW <> Vlan behind Fw and APs not work fine.
WLC = Software Version 7.0.220.0
Logs on WLC :
spamApTask2: Jun 04 11:49:59.494: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:631 Failed to complete DTLS handshake with peer 172.37.251.71
*spamApTask1: Jun 04 11:48:49.323: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:631 Failed to complete DTLS handshake with peer 172.37.251.71
*spamApTask2: Jun 04 11:47:39.149: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:631 Failed to complete DTLS handshake with peer 172.37.251.71
*spamApTask1: Jun 04 11:46:28.978: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:631 Failed to complete DTLS handshake with peer 172.37.251.71
*spamApTask2: Jun 04 11:45:18.806: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:631 Failed to complete DTLS handshake with peer 172.37.251.71
*spamApTask1: Jun 04 11:44:08.632: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:631 Failed to complete DTLS handshake with peer 172.37.251.71
*osapiBsnTimer: Jun 04 11:43:51.235: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:2202 Failed to complete DTLS handshake with peer 172.37.251.71
debud dtls :
*spamApTask1: Jun 04 11:22:42.434: 64:a0:e7:5f:e5:70 record=Alert epoch=0 seq=2
*spamApTask1: Jun 04 11:22:42.435: 64:a0:e7:5f:e5:70 SSL_do_handshake: SSL_ERROR_SSL while communicating with 172.37.251.71 : (null)
*spamApTask1: Jun 04 11:22:42.435: 64:a0:e7:5f:e5:70 Requested by openssl_dtls_process_packet
*spamApTask1: Jun 04 11:22:42.435: dtls_conn_hash_delete: Deleting hash for Local 172.18.3.2:5246 Peer 172.37.251.71:52258
*spamApTask1: Jun 04 11:22:42.435: 64:a0:e7:5f:e5:70 DTLS Connection 0x145520d0 closed by controller
*spamApTask1: Jun 04 11:22:42.436: dtls_conn_hash_search: Searching hash for Local 172.18.3.2:5247 Peer 172.37.251.71:52258
Cordially,

HI,
- On the fw-
a. Make sure the FW is open for udp 5246 and 5247 ports required for the capwap process.
If this is a cisco ASA, you can set up ingress and egress packet captures to see what packets enter and leave the FW for this AP-
cap capin interface match udp any
cap capout interface match udp any
**match captures bidirectional flow for the interesting traffic.
b. Check the logs on the firewall for any drops.
c. cap capdrop type asp-drop all
This will tell you if the pkt was dropped and the reason for the drop
d. You can run the packet-tracer command on the firewall tracking this udp flow-
e.g. packet-tracer input inside udp 3.3.3.3 1212 2.2.2.3 5246 detailed
- What AP model is this? Is it the same AP that connects to the controller if there is no fw in the path?
- Does it use MIC or SSC cert? If SSC, make sure you have SSC checked and you will need to manually enter the hash for the AP on the controller under AP Authorization List -
Security> AP Policies
You can get the hash of the AP (f you dont have it) by enabling the following debug on the controller
debug pm pki enable
Other controller debugs for the AP-
debug mac address
debug capwap error enable
debug capwap events enable
- What about AP console log? Do you have access to that?

Help required with WLC software upgrade

I have a customer with WLC 4402 in use, running software version 7.0.98.0, and supporting 11 APs at present. The customer wants to enlarge the WLAN, which involves increasing the number of APs. I have purchased a new WLC5508, and have installed it onto the network alongside the 4402. the 5508 is running software version 7.0.116.0. Because the wireless network is critical to the user, we want to move the APs over to the new controller while the network is up and running, then remove the 4402.
However, when we set the 5508 as the master controller, or tell one of the APs to use the 5508 as its primary controller, the AP connects to the new controller, downloads the new software version, attempts to load it but reports an error with the unzipped file size of the software and fails to boot. formatting the flash on the AP, then disconnecting the 5508 from the network and rebooting the AP allows it to connect to the 4402, it downloads the older software and boots as normal. A new AP, if connected to the 5508 in a test scenario (ie no 4402) connects, downloads and boots perfectly.
I have the upgrade software to allow the 4402 to be upgraded to 7.0.116.0, but I am concerned that, if this is installed, the existing APs will then fail to boot from the 4402 or the 5508.
all APs are 3502s, running IOS version 12.04(23c)JA when connected to the 4402 and 12.04(23c)JA2 on the 5508.
Any suggestions would be gratefully received
Thanks

Hi Pat,
thanks for the reply. I am off site until the morning, but will attach the colsole output tomorrow.
Your mentioning a corrupt image makes me wonder - we had a lot of trouble setting up the initial config on the new WLC, getting a lot of launch failures. Eventually things seemed to settle down (it certainly booted successfully first time this morning) and getting an AP to connect without a problem made me hope it was just a quirk of the configuration wizard, but I think I will try a reboot of the WLC before I do anything else, just to check it is stable.
If it is a corrupt image it may take a little while to sort, as we have not as yet got a support contract on the 5508 - the plan was to upgrade the existing contract on the 4402 once they were swapped out, but I'll let you know whats going on
Rob

LWAPP assocoation with WLC

hi,
m lwapp cisco 1242ag is not getting associted with wlc.
it is giving following logs in console of AP -
%LWAPP-3-CLIENTEVENTLOG: Performing DNS resolution for CISCO-LWAPP-CONTROLLER
%LWAPP-3-CLIENTERRORLOG: DNS Name Lookup: could not resolve CISCO-LWAPP-CONTROLL
ER
pls help on this.

http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00808f8599.shtml
Check that link
What you should try
clear lwapp or capwap private config
clear nvram
If still no go,
MAke sure that DHCP is proving domain name and DNS ip address
If it still does not join, convert it to aIOS and then clear nvram and then convert back again to lightweight using the latest RCVK image or lightweight ios and see if it works
if not try this:
debug lwapp console cli
debug capwap console cli
AP(config)# ip domain name company.com
AP(config)# ip name-server
Let us know how did you go

The problem I have since I upgraded to Mavericks version 10.9.1 The problem appears only with Mail not with other programs, not even with my browser. When I try to zoom the text of an e-mail I received or sent , I can no longer use the keys Command to e

the problem I have since I upgraded to Mavericks version 10.9.1
The problem appears only with Mail not with other programs, not even with my browser.
When I try to zoom the text of an e-mail I received or sent , I can no longer use the keys Command + to enlarge the text, although I can reduce it with Command -.
As I have a problem with my eyes, This is a serious matter for me.
When I write an e-mail, if I select text and press Command +, it just displaces the text to the right.
Now, my husband has a USB keyboard. If he connects it to my computer, his regular Command + does not work either, but he uses the extended keyboard, then it works. Unfortunately, he needs it for a musical application which does not work with a wireless keyboard.

Firefox 3.6.4 and 3.6.6 use a process called, "plugin-container.exe" which was using up most of my CPU when I opened up multiple tabs that contained Adobe Flash files, and caused Firefox to lock up.
My solution was to use Firefox 3.5.10 which you can get from the Mozilla website at [http://www.mozilla.com/en-US/firefox/all-older.html]
I am using Adobe Flash 10.1.53.64 without any problem in this version of Firefox. Check the release notes, I believe it contains all the latest security fixes in "Firefox 3.6.4".
Hopefully, they will fix Firefox 3.6 in the next version (e.g. Firefox 3.6.7), until then you should probably use "Firefox 3.5.10".

An error The local farm is not accessible. Cmdlets with FeatureDependencyId are not registered after launching a ps1 script from cmd file.

I'm trying to load sharepoint script from *.cmd file.
I have Sharepoint 2010 installed on Windows 7 x64 and SQL server 2008r2.
My cmd file is:
Powershell -v 2 -NonInteractive -NoLogo -File 1.ps1
My sharepoint file 1.ps1 is:
$snapin="Microsoft.SharePoint.PowerShell"
if ($action -eq $null -or $action -eq '')
{<br />
# Action by default is complete uninstallation.
$action='uninstall'
$uninstall = $true
else
$action = $action.ToLower()
switch($action)
{ $_ -eq "uninstall" } { $uninstall = $true; break }
{ $_ -eq "removesolution" } { $removeSolution = $true; break }
{ $_ -eq "deactivatecorpus" } { $deactivateCorpus = $true; break }
{ $_ -eq "deactivatesupport" } { $deactivateSupport = $true; break }
default { Write-Host -f Red "Error: Invalid action: $action "; Exit -1 }
Check the Sharepoint snapin availability.
if (Get-PSSnapin $snapin -ea "silentlycontinue")
Write-Host "PS snapin $snapin is loaded."
elseif (Get-PSSnapin $snapin -registered -ea "silentlycontinue")
Write-Host "PS snapin $snapin is registered."
Add-PSSnapin $snapin
Write-Host "PS snapin $snapin is loaded."
else
Write-Host -f Red "Error: PS snapin $snapin is not found."
Exit -1
$url = "http://pc1/sites/GroupWork/"
$site= new-Object Microsoft.SharePoint.SPSite($url )
$loc= [System.Int32]::Parse(1033)
$templates= $site.GetWebTemplates($loc)
foreach ($child in $templates){ write-host $child.Name " " $child.Title}<br />
$site.Dispose()
The script works fine from the Sharepoint 2010 management shell after launching the shell from the start menu (or from windows cmd by entering powershell -v 2):
PS C:\2> .\1.ps1
PS snapin Microsoft.SharePoint.PowerShell is loaded.
GLOBAL#0 Global template
STS#0 Team Site
STS#1 Blank Site
STS#2 Document Workspace
MPS#0 Basic Meeting Workspace
MPS#1 Blank Meeting Workspace
MPS#2 Decision Meeting Workspace
MPS#3 Social Meeting Workspace
MPS#4 Multipage Meeting Workspace
CENTRALADMIN#0 Central Admin Site
WIKI#0 Wiki Site
BLOG#0 Blog
SGS#0 Group Work Site
TENANTADMIN#0 Tenant Admin Site
{248A640A-AE86-42B7-90EC-45EC8618D6B4}#MySite2 MySite2
{95629DC2-03B1-4C92-AD70-BC1FEAA49E7D}#MySite1 MySite1
{7F01CFE4-F5E2-408B-AC87-E186D21F624C}#NewSiteTemplate NewSiteTemplate
PS C:\2>
I have an access to the database Sharepoint_Config from current domain user and from other 2 users. All users have db_owner rights to the Sharepoint_Config database. But
i've loaded in windows from the user which is dbo in the database (dbo with windows authentication with domain\username for the current user). The dbo user has do_owner rights in the Sharepoint_Config database. I've tried to login under other users and launch
the cmd file but without success.
My PowerShell has version 2.0:
PS C:\2> $psversiontable
Name Value
CLRVersion 2.0.50727.5477
BuildVersion 6.1.7601.17514
PSVersion 2.0
WSManStackVersion 2.0
PSCompatibleVersions {1.0, 2.0}
SerializationVersion 1.1.0.1
PSRemotingProtocolVersion 2.1
After launching the script from 1.cmd file i get an errors:
C:\2>Powershell -v 2 -NonInteractive -NoLogo -File 1.ps1
PS snapin Microsoft.SharePoint.PowerShell is registered.
The local farm is not accessible. Cmdlets with FeatureDependencyId are not regis
tered.
Could not read the XML Configuration file in the folder CONFIG\PowerShell\Regist
ration.
Could not find a part of the path 'C:\2\CONFIG\PowerShell\Registration'.
No xml configuration files loaded.
Unable to register core product cmdlets.
Could not read the Types files in the folder CONFIG\PowerShell\types.
Could not find a part of the path 'C:\2\CONFIG\PowerShell\types'.
"No Types files Found."
Could not read the Format file in the folder CONFIG\PowerShell\format.
Could not find a part of the path 'C:\2\CONFIG\PowerShell\format'.
No Format files Found.
PS snapin Microsoft.SharePoint.PowerShell is loaded.
New-Object : Exception calling ".ctor" with "1" argument(s): "The Web applicati
on at http://Pc1/sites/GroupWork/ could not be found. Verify t
hat you have typed the URL correctly. If the URL should be serving existing con
tent, the system administrator may need to add a new request URL mapping to the
intended application."
At C:\2\1.ps1:48 char:18
+ $site= new-Object <<<< Microsoft.SharePoint.SPSite($url )
+ CategoryInfo : InvalidOperation: (:) [New-Object], MethodInvoca
tionException
+ FullyQualifiedErrorId : ConstructorInvokedThrowException,Microsoft.Power
Shell.Commands.NewObjectCommand
Please help me. I don't understand why the script is launched from the sharepoint management shell but doesn't work from the cmd file.

I have an answer for my problem: for solving a problem I've made several steps:
1. Run farm installation under AD admin credentials - runas /user:Domain1\DomainAdmin1 "C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\14\BIN\psconfigui.exe".
This user has been added as farm administrator in the wizard.
This user has been added as DBO in the SQL Server. (This is the main difference with my previous attempts)
2. Execute a command Add-SPShellAdmin Domain1\UserAccount1 in
the Management Shell of Sharepoint.
3. Run SQL server and add Sharepoint_Shell_Access to the Domain1\UserAccount1
(my main account) in the Config database
4. Run CMD file only from Start->Run menu.
runas /user:Domain1\UserAccount1 "C:\1.cmd".
Do not use Total Commander command prompt or file list for executing *.cmd of *.bat files without root administrator account.
Thanks all for help.

Ap1130 with wlc or not?

Similar Messages

Maybe you are looking for