AP1131AG, WLC44002 and remote capture

Dear,
we have installed a WLC 4402 with about 50 AP1131AG. This works all fine. Now I changed one AP's role to sniffer, and I like to use wireshark for the capturing, but I struggle with the syntax of rpcap adapter command. Can someone help me with this?
Regards
Thomas

Try this link:
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn501480.html
"Wireshark sniffer support-The controller enables you to configure an access point as a network "sniffer," which captures and forwards all the packets on a particular channel to a remote machine that runs packet analyzer software. These packets contain information on timestamp, signal strength, packet size, and so on. Sniffers allow you to monitor and record network activity and to detect problems. In previous controller software releases, only the following packet analyzers are supported: Wildpackets Omnipeek and Airopeek and the AirMagnet Enterprise Analyzer. In controller software release 5.0.148.0, the Wireshark packet analyzer is also supported."
Per your link...
"config
Configure parameters.
ap
Configure access point.
sniff
Sniffer command.
802.11b {enable | disable}
Enable or disable sniffing.
channel
Channel to be sniffed.
server_IP_address
The IP address of the remote machine running Omnipeek, Airopeek,
AirMagnet, or Wireshark
Cisco_AP
Access point configured as the sniffer.

Similar Messages

Routing and Remote Access Logs (Windows Server 2008 R2)

Hi,
I have a Windows 2008 R2 server running Routing and Remote access and users are using PPTP VPN's to connect to our network.
I have been asked to find logs for the following for connections in to our server
Username used for connection
Computer Name
IP Address used by computer connecting
Start/End time of VPN session
Date
Encryption used
I found an article stating to enable RRAS logs you need to run the following command
To enable RAS logs run command “netsh ras set tracing * enabled” and found a series of logs created in this location C:\Windows\tracing
None appear to contain the information I am looking for and was wondering if I was doing this correctly and if not how I am meant to extract this information?
If you require any more details just let me know.
Kind Regards
David

Hi,
I can’t sure which article you have read, but fur the 2008R2 the RAS to enable the log and the debug log in the KB is descried like this, I recommend you to try the KB
mentioned method.
To configure RRAS to enable logging
1. Start Server Manager. Click Start, click Administrative Tools, and then click Server Manager.
2. In the navigation tree, expand Roles, and then expand Network Policy and Access Services.
3. Right-click Routing and Remote Access, and then click Properties.
4. On the Logging tab, select Log errors only, Log errors and warnings, or Log all events, depending on how much information you want to capture.
5. Click OK to save your changes.
The related KB:
RRAS: Logging should be enabled on the RRAS server
http://technet.microsoft.com/zh-cn/library/ee922651(v=ws.10).aspx
Hope this helps.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Remote capture with eos digital rebel xt

Is remote capture possible with windows 8 and the EOS Digital Rebel XT?

There is no Windows 8 driver available for Canon EOS Rebel XT, as far as I am aware of. However, there is a Windows Vista driver available on the Cannon Support websites. Try downloading it and installing it in Windows Vista compatibility mode and and see if it makes the EOS Utility work. If it does you should be able to remote shoot with a USB cable.
I have not tried my old XT with Win 7 or 8 but this may do the trick.
Good luck
EOS 1Ds Mk III, EOS 1D Mk IV EF 50mm f1.2 L, EF 24-70mm f2.8 L,
EF 70-200mm f2.8 L IS II, Sigma 120-300mm f2.8 EX APO
Photoshop CS6, ACR 8.7, Lightroom 5.7

Timelapse remote Capture on G9 - How to?

Hi,
Looking to buy a G9 or G10 to use as a high quality time lapse weather cam as my old Olympus software will not work on any OS after XP. I control 2 Olympus cameras and each takes images every 5 minutes to upload to an ftp website, using a constant file name.
It's proving quite difficult to know if the Canon supplied software (and upgrades for Win8) will do the trick.
From my extensive research I have come up with the following, possibly erroneous and conflicting information.
* ZoomBrowser EX can work with Canon Utilities RemoteCapture Task, both compatible with Win8 according to MS. (No sign of Remote Capture being downloadable from Canon, either as a task for Zoom Browser or a standalone product.)
*CameraWindow DC (available from Canon and compatible with Win8). Vague hints that it can control the camera, but no idea if it can take timelapse at for example 5 minute intervals. And the program will not work in test mode without a camera ... catch 22. Also no help file or guide is available.
*Digital Photo Professional 3.13.00. There was some message about needing EOS Utilities if one needed the Remote Capture facility - even though that doesn't support Powershots.
Does anyone have any idea if any of the above would do what I want with my camera?
Thanks in advance
Stuart

DPP is just an editing program used to convert RAW to jpg so it's out AND since you asked such an interesting question I hooked my G9 up to see if I could do this BUT I only have XP so this might not be 100% correct. I couldn't find any way to use the computer to take a photo with my G9 and I tried Zoombrowser & Camera Window. EOS Utility wouldn't even recognize it so you may need to research other options.
"A skill is developed through constant practice with a passion to improve, not bought."

Remote System and Remote Key Mapping at a glance

Hi,
I want to discuss the concept of Remote System and Remote Key Mapping.
Remote System is a logical system which is defined in MDM Console for a MDM Repository.
We can define key mapping enabled at each table level.
The key mapping is used to distinguish records at Data Manager after running the Data Import.
Now 1 record can have 1 remote system with two different keys but two different records cannot have same remote system with same remote key. So, Remote key is an unique identifier for record for any remote system for each individual records.
Now whenever we import data from a Remote System, the remote system and remote key are mapped for each individual records. Usually all records have different remote keys.
Now, when syndicating back the record with default remote key is updated in the remote system that is sent by xml file format.
If same record is updated two times from a same remote system, the remote key will be different and the record which is latest contains highest remote key.
Now, I have to look at Data Syndication and Remote key.
I have not done Data Syndication but my concept tell if there is duplicate record with same remote system but different remote keys both will be syndicated back. But if same record have two remote keys for same remote system then only the default remote key is syndicated back.
Regards
Kaushik Banerjee

You are right Kaushik,
I have not done Data Syndication but my concept tell if there is duplicate record with same remote system but different remote keys both will be syndicated back.
Yes, but if they are duplicate, they needs to be merged.
But if same record have two remote keys for same remote system then only the default remote key is syndicated back.
This is after merging. So whichever remote key has tick mark in key mapping option(default) , it will be syndicated back.
Pls refer to these links for better understanding.
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/library/uuid/80eb6ea5-2a2f-2b10-f68e-bf735a45705f
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/library/uuid/7051c376-f939-2b10-7da1-c4f8f9eecc8c%0c
Hope this helps,
+ An

Search for [Remote Key] and [Remote System] in Data Manager

Hello all
I would like to be able to search on the remote key and the remote system in the MDM Data Manager is that not possible? I thought I remembered seeing that possibility under the Free-Form Search but now I can't find it.
I have, however, found this in the Data Manager reference guide:
REMOTE SYSTEM AND REMOTE KEY FIELDS
MDM uses the remote systems defined in the Remote Systems table
within the MDM Console to store and maintain key mapping information
for each record or text attribute. It does this using a virtual key
mapping field that you never see in the MDM Client.
This virtual key mapping field is very much like a qualified lookup field
into a virtual key mapping qualified lookup table.
Key Mapping information stored in virtual lookup field
The Remote System and Remote Key fields are normally not visible;
however, they do appear in several places in the MDM Client.
Specifically, both fields: (1) appear in the File > Export dialogs in Record
mode for exporting value pairs; (2) are recognized by the File > Import
dialog in Record mode for importing value pairs; and (3) appear in the
Edit Key Mappings dialogs in both Record mode and Taxonomy mode,
for viewing and editing value pairs.
Is there any way to search on the value in the remote key from the Data Manager?

Not sure search i think not possible.
But you can see keys as mentioned:
Enable Key mapping in Console.
MDM Client maens MDM Data Manager.
They do appear in several places in the MDM Client or Data Manager. Three different methods to see in DM are given already below:
Specifically, both fields: (1) appear in the File > Export dialogs in Record mode for exporting value pairs; (2) are recognized by the File > Import dialog in Record mode for importing value pairs; and (3) appear in the Edit Key Mappings dialogs in both Record mode and Taxonomy mode, for viewing and editing value pairs.
BR,
Alok

Remote Control and Remote View Problem

Hi,
I work at a High School running Netware 6.0 SP5 and Zen works 4.01 ir7.
Remote Control and Remote View works great but I noticed one problem.
We have a logo of the school that is forced down on to the desktop when a
user logs in through group policies. This logo works perfect for the
desktop wall paper and loads every time a user logs in.
When I Remote Control or Remote View a computer the users desktop wall
paper turns from the logo being forced down through group policies to the
desktop to a blue desktop wall paper.
I would prefer the desktop wall paper staying the schools logo when I
Remote Control or Remote View because if the desktop wall paper changes to
the blue color I mentioned above when I Remote Control or Remote View the
users computer, they will know that someone is taking over their computer
which sometimes we dont want them knowing.
We have Windows 98SE computer running Novell Client 3.4 and we have some
computers running Windows XP Professional SP1 and Windows XP Professional
SP2 both running Novell Client 4.91 SP2.
The Remote Control and Remote View problem of the desktop wall paper
changing on the users computer occurs on all operating systems mentioned
above.
Is there a solution to my above problem? When Remote Controlling and
Remote Viewing someone's computer I don't want the desktop wall paper to
change.
Thanks!

Bpilon,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Do a search of our knowledgebase at http://support.novell.com/search/kb_index.jsp
- Check all of the other support tools and options available at
http://support.novell.com.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://support.novell.com/forums)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://support.novell.com/forums/faq_general.html
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://support.novell.com/forums/

Unplugging all network devices from Fios router prevents DVR freezing and remote control lock ups.

All,
I recently had a Verizon tech visit my house due to constant DVR and remote control freezing. TV content was freezing whether it was locally recorded, pulled from another DVR in the house, or On Demand. On a hunch after the tech tested everything and was about to leave, he unplugged my gigabit switch from the Fios router. Lo and behold everything started running perfectly. Since to the tech, the problem was solved, he closed the case and was on his way. The probem is of course I have more devices than the built in router switch provides ports for. My network is compised of an 8 port Netgear gigabit switch downstream from the Fios router with two wireless access points (with their own built in gigbait switches) connecting to the Netgear gigabit switch. There are no loops in the switch topology. I've tried changing out the router, the gigabit switch, removing the wireless acces points individually as well as plugging the access points directly into the Fios router switch (one at a time with no Netgear switch in the middle) and all scenarious cause the DVR/remote control freeezing to come back. The only devices I can plug into the Fios router without causing freezes are PC's....anything with it's own switch essentially brings the network to it's knees. If anyone has an idea how to get my network back in one piece AND make the DVR's/remotes behave, I'd greatly appreciate the help!
My Fios equipment:
MI-424WR GEN-3I rev I (eye) running firmware 40.19.36
5 Motorola HD-DVRs all QIP 7232-2 running software release 1.9.1 platform build 25.39 (Oct. 22, 2012)
Specific config:
75/35 Fios connecting via ethernet from ONT. Set-top boxes connect to Fios router coax port via powered splitter.
*All SNR/dB mesasurements taken by the tech from the set-top boxes and router are well within spec.
Fios router provides DHCP addressing. Wireless N access points are configured for roaming with the same SSID and non-overlapping channels. Access points are not providing routing or IP adressing...all layer 3 and up services still provided by Fios router
Diagram:
ONT
|
Fios Router ---------Cable Splitter---------Set Top Boxes
|
Netgear Switch
|           |
WAP1    WAP2

WayfarerII wrote:
... DVR ... remote ... freezing ... TV ... whether ... locally recorded, pulled from another DVR ...
... tech ... unplugged my gigabit switch from the Fios router ... and ... everything started running perfectly ...
... config:
75/35 Fios ... via ethernet from ONT ... Set-top boxes connect to Fios router via powered splitter ...
ONT
|
| cat5
|
Fios Router ---------Cable Splitter---------Set Top Boxes
|
Netgear Switch
|           |
WAP1    WAP2
I am inclined to echo several of the "tns" comments, particularly with respect to your splitter. My layout is based on a standard 8-port splitter of the type usually supplied in a VZ install. In addition I do have a ChannelPlus device that functions as a powered splitter, but its use is limited to distribution of secondary TV signals to older analog TVs. My first point then is that this may be an offender as "tns" has suggested.
In addition, I'd describe your wiring as "non-standard" (red-colored items in the above diagram)  As you're no doubt aware, with 75/35 you don't really need Cat5e from the ONT (your original diagram). It seems the highest tiers do require it, but in "standard" installations this run is coax directly to an 8-port non-powered splitter (below diagram), then from that splitter via coax to all STBs and CableCards, other TVs, et.), and also to the Actiontec.   Subsequent feeds from the Actiontec to wired devices (including WAPs) are via Ethernet (typically Cat 5e).
In fact I don't immediately see how your STBs get additional services such as On Demand and IMG with the wiring shown in your diagram (perhaps someone can help me out here). In "standard" installs the Actiontec must be connected via coax to the ONT to provide such services to other network clients. I don't see that requirement being met here.
For starters I'd recommend that you change your service from WAN Ethernet to WAN coax. This can easily be accomplished over the telephone. Then I'd run coax directly from the ONT to the Actiontec as in my revised diagram below (blue-colored items). If your setup can manage with this arrangement, I think it will help greatly with the "freezing" issue.
ONT - - - - - - coax - - - - -
                                         |
Fios Router --- coax--- Standard 8-Port Splitter --- coax --- Set Top Boxes
|cat5
Netgear Switch
|cat5          |cat5
WAP1 WAP2
Subsequent Note: You provided additional info while I was composing a response, and I'd like to offer another comment. Structured wiring "panels" of the type usually available are pre-configured to provide data, phone and video. This usually means that one is in certain respects limited by the ideas of the panel designer. I have what can be called a structured wiring layout, but it really is composed of individual small custom networks for each service (automation, security, video, data, telco, etc.), configured so that all wiring terminates in "home run" fashion at a central panel (a few details here: http://forums.verizon.com/t5/Home-Networking/Cmon-Show-Us-Your-Network/m-p/481733#M765 ). This layout makes it easier to make adjustments (and there have been quite a few over the intervening years). I'm thinking that in your case you may have to abandon the powered splitter (presumably) built into the panel in order to avoid your present fix.
Subsequent Subsequent Note:   From your description it seems that you are using more than a single "whole house" DVR to supply programming to other devices. This is a bit puzzling to me because somewhere along the line I recall reading that only a single whole house DVR was allowed on the network. Can you elaborate a bit?

Hp laserjet pro m1217nfw and remote desktop printing

hp laserjet pro m1217nfw and remote desktop printing, is there any issues with said function?

whats the problerm you are having??

Cannot login to Cisco Jabber 10.5.1 over Mobile and Remote Access

Hi,
We have deployed sucessfully VCS Expressway-C and VCS Expressway-E with only 1 zone which is "Unified Communication Traversal" and is for Mobile and Remote Access only. VCS-C and VCS-E are communicating and in statuses everything is active and working. Also VCS-C can communicate with CUCM and CUP (both version 10.5).
Problem is when I deploy Cisco Jabber 10.5.1 on computer outside of LAN and without VPN it start communicating with VCS-E, ask me for accepting certificate (we have certificate only intenally generated on Windows CA) and after that it is trying to connect and after few seconds it will tell me that it can't communicate with server.
Did any of you had same problem or can you advice how to troubleshoot? In Jabber logs there is only something like "Cannot authenticate" error message, but when I startup VPN I can authenticate without any problems.
Thanks

On Expressway-C are your HTTP Allow Lists setup properly? By default, and auto discovered CUCM and IMP should be listed via IP and Hostname, but if not, you'll need to insert manually.
Also, you can look at the config file your Expressway-E would be handing out to Jabber via this method.
From the internet, browse to:
https://vcse.yourdomain.com:8443/Y29sbGFiLmNvbQ/get_edge_config?service_name=_cisco-uds&service_name=_cuplogin
Where:
vcse is your Expressway-E hostname (or CNAME/A record)
yourdomain.com is your own domain
The first directory is your Base64 encoded domain name, remove and trailing equal signs (=)
The XML returned is basically the DNS SRV record information available as if internal for _cisco-uds and _cuplogin
TFTP DNS SRV is optional if you configured TFTP in IMP for your Legacy Clients.

Vpn site to site and remote access , access lists

Hi all, we run remote access and site to site vpn on my asa, my question is Can I create an access list for the site to site tunnel, but still leave the remote access vpn to bypass the access list via the sysopt command, or if I turn this off will it affect both site to site and remote access vpn ?

If you turn off sysopt conn permit-vpn it will apply to both your site to site and remote access vpn...all ipsec traffic. You would have to use a vpn-filter for the site to site tunnel if you wanted to leave the sysopt in there.

Preview and image capture don't save imported scanned image

Hi. Both preview and image capture aquire the scanner and displays the image overview. But when proceeding
to scan, the application simply hangs and no image is saved.
Maybe some prefs file is corrupted. Tried removing the com.apple.Preview from ~/Library/Containers, but didn't help....
What to do???

Not sure if this is relevant:
1) TWAIN-BRIDGE is installed otherwise mavericks won't talk to the scanner.
2) recently added an HP printer (no scanner). Shouldn't conflict with the scanner driver, but then again.....

Preview and Image Capture Not Recognising Scanner

Preview and Image capture have stopped recognising my networked Canon MX350 scanner. It seemed to occur after I used PhotoScore to scan some sheet music but that could be coincidence. I deleted the scanner driver and reinstalled it from the Canon website together with the MP Navigator software, and I am now able to scan from MP Navigator but not Image Capture or Preview. I have run Software Update but no updates are available.

Apple's official documentation only provides an information about printing by using this device - scanner is not listed. I would suggest to look for specific drivers on Canon's official webpage.
OS X: Printer and scanner software available for download - Apple Support

How to use the same services-config for the local and remote servers.

My flex project works fine using the below but when I upload my flash file to the server I doesn't work, all the relative paths and files are the same execpt the remote one is a linux server.
<?xml version="1.0" encoding="UTF-8"?>
<services-config>
    <services>
        <service id="amfphp-flashremoting-service"
            class="flex.messaging.services.RemotingService"
            messageTypes="flex.messaging.messages.RemotingMessage">
            <destination id="amfphp">
                <channels>
                    <channel ref="my-amfphp"/>
                </channels>
                <properties>
                    <source>*</source>
                </properties>
            </destination>
        </service>
    </services>
    <channels>
    <channel-definition id="my-amfphp" class="mx.messaging.channels.AMFChannel">
        <endpoint uri="http://localhost/domainn.org/amfphp/gateway.php" class="flex.messaging.endpoints.AMFEndpoint"/>
    </channel-definition>
    </channels>
</services-config>
I think the problem is the line
        <endpoint uri="http://localhost/domainn.org/amfphp/gateway.php" class="flex.messaging.endpoints.AMFEndpoint"/>
but I'm not sure how to use the same services-config for the local and remote servers.

paul.williams wrote:
You are confusing "served from a web-server" with "compiled on a web-server". Served from a web-server means you are downloading a file from the web-server, it does not necessarily mean that the files has been generated / compiled on the server.
The server.name and server.port tokens are replaced at runtime (ie. on the client when the swf has been downloaded and is running) not compile time (ie. while mxmlc / ant / wet-tier compiler is running). You do not need to compile on the server to take advantage of this.
Hi Paul,
In Flex, there is feature that lets developer to put all service-config.xml file configuration information into swf file. with
-services=path/to/services-config.xml
IF
services-config.xml
have tokens in it and user have not specified additional
-context-root
and this swf file is not served from web-app-server (like tomcat for example) than it will not work,
Flash player have no possible way to replace token values of service-config.xml file durring runtime if that service-config.xml file have been baked into swf file during compilation,
for example during development you can launch your swf file from your browser with file// protocol and still be able to access blazeDS services if
-services=path/to/services-config.xml
have been specified durring compilation.
I dont know any better way to exmplain this, but in summary there is two places that you can tell swf about service confogiration,
1) pass -services=path/to/services-config.xml parameter to compiler this way you tell swf file up front about all that good stuff,
or 2) you put that file on the webserver( in this case, yes you should have replacement tokens in that file) and they will be repaced at runtime .

One WLC for Headquarter and Remote Site

Hi
I have a question about the WLC remote deployment.
We have the following design at the moment:
Headquarter
- Network 192.168.49.0 /24
- WLC 4402 Version 4.2.61.0
-- 3 x LAP1252
-- Layer 3 LWAPP
-- SSID wep
-- SSID wpa
- Windows PDC with Active Directory, DHCP Server and local Data Storage
- ACS Version 3.2 for TACACS and RADIUS authentication --> External DB to Active Directory
Remote Site
- Network 192.168.50.0 /24
- 2 x LAP1252
-- SSID wep
-- SSID wpa
- Windows PDC with Active Directory, DHCP Server and local Data Storage
- ACS Version 3.2 for TACACS and RADIUS authentication --> External DB to Active Directory
Connection between Headquarter and Remote Site
- 2 Mbit ADSL
The problem is, that the wireless clients on the remote site get an ip address out of the headquarter DHCP Range 192.168.49.0 /24. The users on the remote site
most of the time only use the local data server in the remote office. With the actual design the hole traffic is switched over the 2 Mbit ADSL connection the the
WLC in the headquarter and back to the remote site. That works but it is not that performant.
The problem could be solved with HREAP, but what I think is, that it is not possible to have the same SSID at headquarter and remote site with different VLANs.
How can I achieve, that the clients on the remote site connect to the same SSID (wep or wpa), get an ip address from the remote site DHCP server (192.168.50.0)
and the traffic is switched localy.
I hope you understand what the problem is.
Thanks in advance for your help!

Yes, putting the remote AP's in HREAP mode will allow the same WLANs to be available on the AP's but the traffic would be locally switched at the AP instead of being tunneled back to the controller. After you put the AP in HREAP mode you then would configure which VLAN you want traffic for each WLAN to be dumped onto for that AP.

AP1131AG, WLC44002 and remote capture

Similar Messages

Maybe you are looking for