AP1131G fail to bring ethernet link up

My AP1131Gs was automomous and I was upgrade to LAPs.After few days several APs was fail due to ethernet cable(one of pins is broken).I can not bring it up
connect to WLC anymore.Then I try to recover back to automomous by press Mode switch on APs through TFTP.It is back to IOS image but I found the APs FE0 and BVI1 always down.I try to change configure FE0 to speed 100/duplex full and it is up( link up/ping OK). But I can not upgrade this APs as before.
I was told this is AP bug?Is is true?
Someone could give me further info about this?

I tried this once and it worked. If IOS is running on AP login and do:
archive download-sw /overwrite tftp:///
Example:
archive download-sw /overwrite tftp://10.4.1.20/C:\TFTP-Root/c1250-rcvk9w8-tar.124-10b.JA3.tar
Good luck

Similar Messages

'Failed to bring network up' wireless ath5k [SOLVED]

After a fresh install I tried to connect to my wireless network using
netctl, which resulted in the following error:
netctl status wlp0s6
● netctl@wlp0s6\x2dWLAN\x2d50114.service - Networking for netctl profile wlp0s6-WLAN-50114
Loaded: loaded (/usr/lib/systemd/system/[email protected]; static)
Active: failed (Result: exit-code) since Tue 2014-08-19 13:22:55 CEST; 2min 0s ago
Docs: man:netctl.profile(5)
Process: 3512 ExecStart=/usr/lib/network/network start %I (code=exited, status=1/FAILURE)
Main PID: 3512 (code=exited, status=1/FAILURE)
Aug 19 13:22:49 faze network[3512]: Starting network profile 'wlp0s6-WLAN-50114'...
Aug 19 13:22:55 faze network[3512]: Failed to bring the network up for profile 'wlp0s6-WLAN-50114'
Aug 19 13:22:55 faze systemd[1]: netctl@wlp0s6\x2dWLAN\x2d50114.service: main process exited, code=exited, status=1/FAILURE
Aug 19 13:22:55 faze systemd[1]: Failed to start Networking for netctl profile wlp0s6-WLAN-50114.
Aug 19 13:22:55 faze systemd[1]: Unit netctl@wlp0s6\x2dWLAN\x2d50114.service entered failed state.
So I looked into journalctl -xn
-- Logs begin at Tue 2014-08-19 02:35:29 CEST, end at Tue 2014-08-19 13:27:29 CEST. --
Aug 19 13:24:56 faze sudo[3714]: pam_unix(sudo:session): session opened for user root by (uid=0)
Aug 19 13:24:56 faze sudo[3714]: pam_unix(sudo:session): session closed for user root
Aug 19 13:27:23 faze sudo[3868]: erik : TTY=pts/1 ; PWD=/home/erik ; USER=root ; COMMAND=/usr/bin/netctl start wlp0s6-WLAN-50114
Aug 19 13:27:23 faze sudo[3868]: pam_unix(sudo:session): session opened for user root by (uid=0)
Aug 19 13:27:23 faze network[3879]: Starting network profile 'wlp0s6-WLAN-50114'...
Aug 19 13:27:29 faze network[3879]: Failed to bring the network up for profile 'wlp0s6-WLAN-50114'
Aug 19 13:27:29 faze systemd[1]: netctl@wlp0s6\x2dWLAN\x2d50114.service: main process exited, code=exited, status=1/FAILURE
Aug 19 13:27:29 faze systemd[1]: Failed to start Networking for netctl profile wlp0s6-WLAN-50114.
-- Subject: Unit netctl@wlp0s6\x2dWLAN\x2d50114.service has failed
-- Defined-By: systemd
-- Support: http://lists.freedesktop.org/mailman/listinfo/systemd-devel
-- Unit netctl@wlp0s6\x2dWLAN\x2d50114.service has failed.
-- The result is failed.
Aug 19 13:27:29 faze systemd[1]: Unit netctl@wlp0s6\x2dWLAN\x2d50114.service entered failed state.
Aug 19 13:27:29 faze sudo[3868]: pam_unix(sudo:session): session closed for user root
Nothing new here
After that I tried ip link set wlp0s6 up, which spew out this error:
RTNETLINK answers: Operation not possible due to RF-kill
From here on, I don't really know what to do.
lspci -k output:
00:00.0 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
Subsystem: Fujitsu Technology Solutions Device 10cd
Kernel driver in use: agpgart-via
Kernel modules: via_agp
00:00.1 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
00:00.2 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
00:00.3 Host bridge: VIA Technologies, Inc. PT890 Host Bridge
Kernel modules: via_agp
00:00.4 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
00:00.7 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237/VX700 PCI Bridge
Kernel modules: shpchp
00:06.0 Ethernet controller: Qualcomm Atheros AR2413/AR2414 Wireless Network Adapter [AR5005G(S) 802.11bg] (rev 01)
Subsystem: Qualcomm Atheros Compex Wireless 802.11 b/g MiniPCI Adapter, Rev A1 [WLM54G]
Kernel driver in use: ath5k
Kernel modules: ath5k
00:0f.0 IDE interface: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller (rev 80)
Subsystem: Fujitsu Technology Solutions Device 10cd
Kernel driver in use: sata_via
Kernel modules: sata_via, pata_acpi, ata_generic
00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
Subsystem: Fujitsu Technology Solutions Device 10cd
Kernel driver in use: pata_via
Kernel modules: pata_via, pata_acpi, ata_generic
00:10.0 USB controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
Subsystem: Fujitsu Technology Solutions Device 10cd
Kernel driver in use: uhci_hcd
Kernel modules: uhci_hcd
00:10.1 USB controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)
Subsystem: Fujitsu Technology Solutions Device 10cd
Kernel driver in use: uhci_hcd
Kernel modules: uhci_hcd
00:10.4 USB controller: VIA Technologies, Inc. USB 2.0 (rev 86)
Subsystem: Fujitsu Technology Solutions Device 10cd
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South]
Subsystem: Advanced System Products, Inc Device 1734
Kernel modules: i2c_viapro
00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
Subsystem: Fujitsu Technology Solutions Device 10cd
Kernel driver in use: snd_via82xx
Kernel modules: snd_via82xx
00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem Controller (rev 80)
Subsystem: Fujitsu Technology Solutions Device 10cd
Kernel driver in use: snd_via82xx_modem
Kernel modules: snd_via82xx_modem
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 78)
Subsystem: Fujitsu Technology Solutions Device 10cd
Kernel driver in use: via-rhine
Kernel modules: via_rhine
01:00.0 VGA compatible controller: VIA Technologies, Inc. CN700/P4M800 Pro/P4M800 CE/VN800 Graphics [S3 UniChrome Pro] (rev 01)
Subsystem: Fujitsu Technology Solutions Device 10cd
Kernel modules: viafb
Any ideas?
Last edited by er1k (2014-08-19 10:28:49)

Nevermind, got it working.
It seems I just forgot to type the rest of the clunky auto-generated network profile name.
Thanks for the quick help nonetheless!
Last edited by er1k (2014-08-19 10:29:34)

SL500 - ethernet link light always on

Wondering if anyone else has/is having a problem with their lappy. The ethernet link light is always on whether or not there is a cable attached or not. This happens with the factory install (XP) or my own Windows 7 install. If I disable the NIC the light goes off, but anytime the NIC is enabled, and the cabled isnt plugged in, the light is on. If I attached a cable to the NIC it doesnt obtain an IP, still stays at the 169.254... The BIOS is the latest ver. and IPCONFIG will show a 169.254.blah.blah address which suggests to me its just stuffed.. anyone else seen this b4??

Turns out after a couple of years of 'not worrying about it' and using a work around of a USB ethernet adapter.... it turns out the rest of the world has the same issue as me with the SL500 series.. Enabling/forcing 10mb/full duplex, the connection will work.. turn it to auto or anything else.. it fails.. Some have reported problems with work on battery but plugging in AC power causes it to fail.. My issue, is that if I set it to auto or 1Gb Auto, and reboot, the ethernet light will stay on not stop, even if there is no cable attached.. This is seen even when sitting at a PXE boot or BIOS screen with no cable atached... If I then reboot into the O.S... set it to 10Mb/Full, and reboot again.. all is well, At that setting even in the BIOS and I disconnect the cable the lights go off (as you would expect)..
I have seen dozens upon dozens of posts over the net about the exact same issue (it just took a long time to find what the hell I was chasing, and enough time to care to find out too).. But it seems theres issues with the capacitors on the motherboard for the particular NIC for this machine.. AND.. as reported by dozens and dozens.. is to replace 1-2 capcitors on the motherboard to resolve.. (but having worked for IBM, before it the 'THINK' range was bought out by Lenovo, the fix is to replace the motherboard entirely..)

Failed while creating virtual Ethernet switch. Failed to connect Ethernet switch port

Hello Folks
I am completely stuck with the configuration of my virtual networks. I have one logical switch left to add to one of my Hyper-V 2012 R2 hosts when I started getting the error below when I try to add logical switches to either Hyper-V Host. I have been using
the document. 'Hybrid Cloud with NVGRE (Cloud OS)' to implement the virtual networking. Basically using the exact configuration that is in the document. I have added the PA Logical Network and the Network adapters and added the logical switch for it to my
hyper-v 2012 R2 host and everything was fine. I am now trying to add my ISCSI Logical Switch to the host and this is the error I get. My other Hyper-V host I get this error for any logical switch I am trying to add. Can someone help me with this error. I haven't
been able to find any information about it.
Also a some quick info on tracing an error like this so I can figure out what is causing it.
Thsi is my configuration so far
So as far as I know everything is peachy untill the error below. Dead stop now
Error (12700)
VMM cannot complete the host operation on the 08-NY-VHOST01.accounts.ccac-ont.ca server because of the error: Failed while creating virtual Ethernet switch.
Failed to connect Ethernet switch port (switch name = '******', port name = '88C16766-ED02-4AC0-8CD7-660AC9D424DD', adapter GUID = '{FAF431D8-0124-4E40-BB3B-9234BAA02973}'): The system cannot find the file specified. (0x80070002).
Unknown error (0x800b)
Thank you for your time
Christopher
Christopher Scannell

notice your GUID? you may want to consider ensuring that is the same GUID associated in your database. Sometimes during data corruption theres a smidge of a chance your sql database kind of either pulls old guids esp if this was reverted to snapshot
without it being powered off etc.
I would try that first. then i would consider if you get to configure that with your current liscense associated with the host. I would need way more info to help any further

Customer Equipment for Metro Ethernet Link

Hi All
It has been some time since I utilised Cisco network kit to provide private circuit point to point connectivity and I wonder if someone could give me a little guidence.
The customer is shortly to implement a new 100Mb Metro Ethernet link to connect two of their branches. They initially intend to use the link for data only traffic but eventually will want to route VOIP traffic across the link so bandwidth management and QoS will be essential components. It is unlikely that further links will be added to this link so built in expansion of the chosen routers may not be required.
Budget will be an issue on this so I would appreciate any advice or recomendations.
Thanks
J.

Hello James,
I think it would be better to get in touch with your Cisco Account Team as this question cannot be answered on a forum post.
Thanks,
Karim

Win Server 2012 Failover Cluster - Error: Failed to bring cluster disk online

Hi Technet
I'm currently running running 2 VMs Win Server 2012 and would like to test Failover Clustering for one of our FTP server
I've added on both servers an additional partition, formatted and Online
One of the drives comes Online but cannot bring the 2nd disk online from the cluster manager
Error: failed to bring resource online - clustered storage is not connected to the node
Assistance would be greatly appreciated
Thank you
Jabu

Hi jsibeko,
Since the VMware offer the MSCS shared storage solution themselves, I suggest you first ask VMware whether that shared storage is supported with your vSphere edition, I found
some VMware KB about the VMware shared storage for MSCS, may you can get more tips.
The VMware KB:
Microsoft Clustering on VMware vSphere: Guidelines for supported configurations (1037959)
http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1037959
Microsoft Cluster Service (MSCS) support on ESXi/ESX (1004617)
http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1004617
I’m glad to be of help to you!
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Root.sh fails to bring up crs

Hi All,
I am installing 11gR2 on IBM AIX.
Every ran fine. when i ran root.sh
CRS-2676: Start of 'ora.diskmon' on 't24db1' succeeded
CRS-2676: Start of 'ora.cssd' on 't24db1' succeeded
CRS-2672: Attempting to start 'ora.ctssd' on 't24db1'
CRS-2676: Start of 'ora.ctssd' on 't24db1' succeeded
ASM created and started successfully.
DiskGroup OCR_VOTE created successfully.
clscfg: -install mode specified
Successfully accumulated necessary OCR keys.
Creating OCR keys for user 'root', privgrp 'system'..
Operation successful.
CRS-2672: Attempting to start 'ora.crsd' on 't24db1'
CRS-2676: Start of 'ora.crsd' on 't24db1' succeeded
CRS-4256: Updating the profile
Successful addition of voting disk 70e7b3c678074f2bbfcf933764645975.
Successful addition of voting disk a85fe5cb0c9a4f88bf5adf830732d62f.
Successful addition of voting disk 52d343aad6374f79bf0257908be9a6c9.
Successfully replaced voting disk group with +OCR_VOTE.
CRS-4256: Updating the profile
CRS-4266: Voting file(s) successfully replaced
## STATE File Universal Id File Name Disk group
1. ONLINE 70e7b3c678074f2bbfcf933764645975 (/dev/rhdisk10) [OCR_VOTE]
2. ONLINE a85fe5cb0c9a4f88bf5adf830732d62f (/dev/rhdisk11) [OCR_VOTE]
3. ONLINE 52d343aad6374f79bf0257908be9a6c9 (/dev/rhdisk5) [OCR_VOTE]
Located 3 voting disk(s).
CRS-2673: Attempting to stop 'ora.crsd' on 't24db1'
CRS-2677: Stop of 'ora.crsd' on 't24db1' succeeded
CRS-2673: Attempting to stop 'ora.asm' on 't24db1'
CRS-2677: Stop of 'ora.asm' on 't24db1' succeeded
CRS-2673: Attempting to stop 'ora.ctssd' on 't24db1'
CRS-2677: Stop of 'ora.ctssd' on 't24db1' succeeded
CRS-2673: Attempting to stop 'ora.cssdmonitor' on 't24db1'
CRS-2677: Stop of 'ora.cssdmonitor' on 't24db1' succeeded
CRS-2673: Attempting to stop 'ora.cssd' on 't24db1'
CRS-2677: Stop of 'ora.cssd' on 't24db1' succeeded
CRS-2673: Attempting to stop 'ora.gpnpd' on 't24db1'
CRS-2677: Stop of 'ora.gpnpd' on 't24db1' succeeded
CRS-2673: Attempting to stop 'ora.gipcd' on 't24db1'
CRS-2677: Stop of 'ora.gipcd' on 't24db1' succeeded
CRS-2673: Attempting to stop 'ora.mdnsd' on 't24db1'
CRS-2677: Stop of 'ora.mdnsd' on 't24db1' succeeded
CRS-2672: Attempting to start 'ora.mdnsd' on 't24db1'
CRS-2676: Start of 'ora.mdnsd' on 't24db1' succeeded
CRS-2672: Attempting to start 'ora.gipcd' on 't24db1'
CRS-2676: Start of 'ora.gipcd' on 't24db1' succeeded
CRS-2672: Attempting to start 'ora.gpnpd' on 't24db1'
CRS-2676: Start of 'ora.gpnpd' on 't24db1' succeeded
CRS-2672: Attempting to start 'ora.cssdmonitor' on 't24db1'
CRS-2676: Start of 'ora.cssdmonitor' on 't24db1' succeeded
CRS-2672: Attempting to start 'ora.cssd' on 't24db1'
CRS-2672: Attempting to start 'ora.diskmon' on 't24db1'
CRS-2676: Start of 'ora.diskmon' on 't24db1' succeeded
CRS-2676: Start of 'ora.cssd' on 't24db1' succeeded
CRS-2672: Attempting to start 'ora.ctssd' on 't24db1'
CRS-2676: Start of 'ora.ctssd' on 't24db1' succeeded
CRS-2672: Attempting to start 'ora.asm' on 't24db1'
CRS-2676: Start of 'ora.asm' on 't24db1' succeeded
CRS-2672: Attempting to start 'ora.crsd' on 't24db1'
CRS-2676: Start of 'ora.crsd' on 't24db1' succeeded
CRS-2672: Attempting to start 'ora.evmd' on 't24db1'
CRS-2676: Start of 'ora.evmd' on 't24db1' succeeded
Timed out waiting for the CRS stack to start.
I can also do the ocrcheck and i am also able to connect to ASM.
crs process is not coming up.
I tried to start it manually but no luck.
alert log
[crsd(11534476)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:29:50.913
[crsd(11534476)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:29:52.130
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:29:53.760
[crsd(11468998)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:29:54.029
[crsd(11468998)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:29:55.246
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:29:55.246
[ohasd(6947036)]CRS-2771:Maximum restart attempts reached for resource 'ora.crsd'; will not restart.
2011-09-21 20:51:59.589
[crsd(8650916)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:51:59.854
[crsd(8650916)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:52:00.895
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:52:02.588
[crsd(9306182)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:52:02.852
[crsd(9306182)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:52:04.024
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:52:05.693
[crsd(9306184)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:52:05.961
[crsd(9306184)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:52:07.174
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:52:08.807
[crsd(11337884)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:52:09.078
[crsd(11337884)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:52:10.289
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:52:11.942
[crsd(11206904)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:52:12.207
[crsd(11206904)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:52:13.400
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:52:15.031
[crsd(11337894)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:52:15.302
[crsd(11337894)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:52:16.521
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:52:18.132
[crsd(11337896)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:52:18.403
[crsd(11337896)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:52:19.627
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:52:21.225
[crsd(9306200)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:52:21.498
[crsd(9306200)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:52:22.717
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:52:25.895
[crsd(8650934)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:52:26.176
[crsd(8650934)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:52:27.369
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:52:29.046
[crsd(9306206)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:52:29.316
[crsd(9306206)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:52:30.511
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:52:32.169
[crsd(11337908)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:52:32.435
[crsd(11337908)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:52:33.629
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:52:33.630
[ohasd(6947036)]CRS-2771:Maximum restart attempts reached for resource 'ora.crsd'; will not restart.
2011-09-21 20:57:11.777
[ctssd(8388722)]CRS-2405:The Cluster Time Synchronization Service on host t24db1 is shutdown by user
2011-09-21 20:58:15.374
[ctssd(8519782)]CRS-2403:The Cluster Time Synchronization Service on host t24db1 is in observer mode.
2011-09-21 20:58:15.391
[ctssd(8519782)]CRS-2407:The new Cluster Time Synchronization Service reference node is host t24db1.
2011-09-21 20:58:16.064
[ctssd(8519782)]CRS-2401:The Cluster Time Synchronization Service started on host t24db1.
2011-09-21 20:58:32.499
[crsd(11862176)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:58:33.649
[crsd(11862176)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:58:34.450
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:58:36.075
[crsd(11534462)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:58:36.339
[crsd(11534462)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:58:37.560
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:58:39.190
[crsd(9699394)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:58:39.555
[crsd(9699394)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:58:40.677
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:58:42.311
[crsd(9699396)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:58:42.586
[crsd(9699396)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:58:43.790
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:58:45.435
[crsd(11600058)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:58:45.720
[crsd(11600058)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:58:46.909
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:58:48.536
[crsd(11600060)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:58:48.799
[crsd(11600060)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:58:50.037
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:58:51.670
[crsd(9699410)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:58:51.940
[crsd(9699410)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:58:53.151
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:58:56.298
[crsd(11600072)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:58:56.559
[crsd(11600072)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:58:57.784
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:58:59.428
[crsd(9699414)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:58:59.733
[crsd(9699414)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:59:00.910
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:59:02.522
[crsd(9699416)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:59:02.798
[crsd(9699416)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:59:04.030
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:59:05.624
[crsd(9699418)]CRS-1012:The OCR service started on node t24db1.
2011-09-21 20:59:05.899
[crsd(9699418)]CRS-1201:CRSD started on node t24db1.
2011-09-21 20:59:07.120
[ohasd(6947036)]CRS-2765:Resource 'ora.crsd' has failed on server 't24db1'.
2011-09-21 20:59:07.121
[ohasd(6947036)]CRS-2771:Maximum restart attempts reached for resource 'ora.crsd'; will not restart.
crsd log
2011-09-21 20:59:06.013: [ default][1]clsu_get_private_ip_addresses: required buffer number is 2. Buffer number passed in 1 is not enough. Return [8]
2011-09-21 20:59:06.013: [GIPCXCPT][1] gipcShutdownF: skipping shutdown, count 2, from [ clsinet.c : 1735], ret gipcretSuccess (0)
2011-09-21 20:59:06.014: [GIPCXCPT][1] gipcShutdownF: skipping shutdown, count 1, from [ clsgpnp0.c : 1021], ret gipcretSuccess (0)
2011-09-21 20:59:06.015: [ CRSCCL][1]Listening endpoint created sucessfully @ (ADDRESS=(PROTOCOL=tcp)(DEV=52)(HOST=192.168.50.15)(PORT=49390)).con = 116b2c4f0
2011-09-21 20:59:06.018: [ CRSCCL][10799]CSS Group Registration complete.
2011-09-21 20:59:06.018: [ CRSCCL][10799]cclGetMemberData called
2011-09-21 20:59:06.020: [ CRSCCL][10799]Obtained first membership map.
2011-09-21 20:59:06.020: [ CRSCCL][10799]Dumping member data ------------------
2011-09-21 20:59:06.020: [ CRSCCL][10799]Member (1, 1411327295) on node port=.
2011-09-21 20:59:06.020: [ CRSCCL][10799]Done ------------------
2011-09-21 20:59:06.020: [ CRSCCL][10799]Waiting for reconfigs
2011-09-21 20:59:06.020: [ CRSCCL][11056]cclCommunicationHandler started.
2011-09-21 20:59:06.020: [ CRSCCL][1]cclLibShutdown called
2011-09-21 20:59:06.120: [ CRSCCL][10799]CCL Shutting down.
2011-09-21 20:59:06.122: [ CRSCCL][10799]CSS Group Unregister complete.
2011-09-21 20:59:06.122: [ CRSCCL][11056]Comunications Shutdown.
2011-09-21 20:59:06.123: [ CRSCCL][10799]Membership Monitor exiting ...
2011-09-21 20:59:06.123: [ CRSCCL][1]Clsc shutting down
2011-09-21 20:59:06.123: [ CRSCCL][1]Clsc server shutdown
2011-09-21 20:59:06.123: [ COMMCRS][1]clscugblmterm: (1158d7970) cleaning up icon (116b2bef0) with 1 cons
2011-09-21 20:59:06.123: [ COMMCRS][1]clscugblmterm: (1158d7970) cleaning up open icon (116b2bef0)
2011-09-21 20:59:06.123: [ CRSCCL][1]Clsc UGBLM shutdown
2011-09-21 20:59:06.123: [ CRSCCL][1]Clsc shutdown Done
2011-09-21 20:59:06.123: [ CRSCCL][1]ccllibShutdown done.
2011-09-21 20:59:06.123: [CLSFRAME][1] clsCclInit returned failure:4
2011-09-21 20:59:06.123: [CLSFRAME][1] Unable to start module-to-module comms: 2
2011-09-21 20:59:06.123: [ CRSD][1][PANIC] CRSD exiting: unable to start CLS framework
2011-09-21 20:59:06.123: [ CRSD][1] Done.
Please assist me on this.
Thanks and Regards,
Daniesh

1. try to give root capabilities with CAP_NUMA_ATTACH, CAP_BYPASS_RAC_VMM, and CAP_PROPAGATE
2. install 11.2.0.2 version
I solved the problem rootsh fails to bring up crs.

Windows host cannot establish Ethernet link to Arch Router

This is a weird problem.
I have a Windows host about 20 meters away from my Arch Router, the Ethernet cable goes into the wall, with wall sockets, so it's a total of 3 cables (1 in wall, 1 @ router, 1 @ host). I've tested the Ethernet cables with a LAN tester, they are all fine. When I connect the host to a Linksys router using the same cables, an IP address is obtained and the link is up and running.
But when I connect the host to my Arch Router (an Arch computer with some network cards), no ethernet link at all is detected. No lights on the ethernet card of the host, and ethtool on the router reports the link being down. I have connected my laptop to this ethernet card of the router and it works just fine, I get an IP and I can surf the web etc.
I really have no clue why this other host cannot establish a link. Does anyone have a clue what the problem might be?

pyther is right. Check for Auto-MDIX support on your network cards.
What network cards are you using?
Rule of thumb:
Auto-MDIX is a requirement in the Gigabit Ethernet specification, so proper Gigabit capable cards will work 99% of the time whatever cable you use.
Fast Ethernet (100mbit) and below does not have Auto-MDIX in it's specification, so those 9 out of 10 of those cards will not perform it! When connecting these directly to another network card, use a cross-cable.
Also make sure the network cards are in working order. I assume the ArchRouter PC's network runs fine when you connect that to your Linksys router?

Alerts for metro ethernet link

Hi,
Kindly let me know " How to enable alerts for metro ethernet link"
Thanks..

Hello Gureshi,
they are probably referring to OAM, CFM and other mechanisms to detect link or service failure in metro ethernet scenarios
see
http://www.cisco.com/en/US/docs/switches/metro/me3400e/software/release/12.2_52_se/configuration/guide/swoam.html
Hope to help
Giuseppe

Failed to lookup External Link

Hi,
I just upgraded to EP7 SP12 and deployed the ESS BP. When I try to preview Content Administration -> Portal Content -> Content Provided by SAP -> Employee Self Service -> iViews -> Benefits and Payment -> Benefits Participation, we see the below error.
com.sapportals.portal.prt.runtime.PortalRuntimeException: Failed to lookup External Link for: portal_content/com.sap.pct/every_user/com.sap.pct.erp.ess.bp_folder/com.sap.pct.erp.ess.iviews/com.sap.pct.erp.ess.benefits_payment/com.sap.pct.erp.ess.benparticipation
Any one have any ideas?
Your help is greatly appreciated.
Regards,
Rick

I did some more research. It seems like we are having the same problem on another portal server. So I don't think I caused the problem. This is coming from the standard business planning pages like planning wizard, planning modeler, etc.

Monitoring ethernet links

Hello All,
Is there any other method to monitor ethernet links apart from IP sla and monitoring tunnel.
Regards,
Sathvik

I take it you want to verify confirmed end-end reachability of both sides of an Ethernet connection from the router itself. The usual approach is to use an external tools that looks at each end's characteristics and makes a conclusion based on that.
If you want something closer to the absolute truth then IP SLA and tunnel monitoring are good ones. Depending on the platform you may be able to use something like mediatrace as well. You can also leverage embedded event manager (EEM) to give you some insight.

Ethernet Link Status Detection

Hi,
I am trying to write a program to detect the ethernet link status of an hme/eri ethernet driver.
It is possible to do so using the "ndd -get /dev/hme link_status" command. However, I need
a very efficient inplementation which can accomplish this in a couple of ms.
The ndd man page describes that it uses some ioctl calls to the driver. However, I was not able
to find any specifics of how to make the ioctl call. The /usr/inlcude/sys/hme.h page provides some
#define that may be being used but I still haven't been able to figure out how to make the ioctl
call.
Previously, I was planning to use the kstat API which has an ifspeed parameter, but my tests
show that this is not updated if the ethernet link goes down.
Any help by providing details of the ioctl call or pointing out some alternative approach will be very much appreciated.
Thanks
Pari

mlebryant wrote:
Network Settings for Ethernet says Not Connected.
Status: Cable Unplugged
Either the cable for Ethernet is not plugged in or the device at the other end is not responding.
Well, was/is it? You make no mention of checking.
Please detail ALL you have done so far in the way of troubleshooting? Need this info to avoid the been there done that scenarios.
Did you run Diagnostics? Results?

Mac OS X Server v10.7 does not show the ethernet link aggregated interface I created in Server Hardware Network Dialogue window. Are link aggregated ethernet connections not supported in Lion Server?

Mac OS X Server v10.7 does not show the ethernet link aggregated interface i created. Does Lion server support ethernet link aggregated interfaces?

Thanks for responding Cold--
Hardware: Mac Pro 3.0 GHZ quad core xeon
I read the link but it still does not explain why the aggregated dual ethernet interface does not show up in the Network tab of the hardware section Lion Server. I was able to see it on the network and looks to be using a single static IP that I assigned. My concern was that is this supported and will it allow for failover and double performance of the single network interface.
Any thoughts?
Thanks again!

Time Machine fails with "error while linking files on the backup volume"

One of my drives was nearly full. I moved some folders from that drive to one that had more space.
The next TM backup failed with "error while linking files on the backup volume". A full backup is about 620 GB, although this backup shouldn't have been a complete one. There was 570+ GB free on the drive.
A Disk Verify reported "Drive appears to be okay." Earlier TM backups appeared to be fine (at least accessible). I swapped the TM drive for another, initialized it, and TM used that drive with no complaints.
What does the message mean?
Thanks,
harv47

Pondini wrote:
harv47 wrote:
The Time Machine Buddy widget shows no messages. None of the buttons do anything.
What am I doing wrong?
See #A1 in the Time Machine - Troubleshooting *User Tip,* also at the top of this forum.
Your user account may not have permission to see the logs.
The sentence beginning "If the message area is blank ..." shows how to figure out if that's the problem, and how to fix it.
Post back if it's not clear, or doesn't work.
The Tip had the answer. It was permissions.
What follow are the messages for the last unsuccessful TM backup (on v.3), followed by
the successful TM backup on the replacement drive (v.1). The line
"Copied 11 files (0 bytes) from volume Bay 3 HPFS+." was odd.
Starting standard backup
Backing up to: /Volumes/Time Machine v.3/Backups.backupdb
Event store UUIDs don't match for volume: Bay 3 HPFS+
Event store UUIDs don't match for volume: Macintosh HD
Node requires deep traversal:/Volumes/Bay 3 HPFS+ reason:kFSEDBEventFlagMustScanSubDirs|
Node requires deep traversal:/ reason:kFSEDBEventFlagMustSc
(Finished May 4, 2010 9:31:21 AM-- Status unknown)
Starting standard backup
Backing up to: /Volumes/TimeMachine v.1/Backups.backupdb
Event store UUIDs don't match for volume: Bay 3 HPFS+
Event store UUIDs don't match for volume: Bay 2 HPFS+
Event store UUIDs don't match for volume: Macintosh HD
Backup content size: 169.1 GB excluded items size: 0 bytes for volume Bay 3 HPFS+
Backup content size: 305.5 GB excluded items size: 0 bytes for volume Bay 2 HPFS+
Backup content size: 145.7 GB excluded items size: 7.5 MB for volume Macintosh HD
No pre-backup thinning needed: 744.36 GB requested (including padding), 931.15 GB available
Waiting for index to be ready (909 > 0)
Copied 1951 files (169.0 GB) from volume Bay 3 HPFS+.
Copied 4999 files (474.3 GB) from volume Bay 2 HPFS+.
Copied 410304 files (612.4 GB) from volume Macintosh HD.
No pre-backup thinning needed: 712.2 MB requested (including padding), 315.09 GB available
Copied 11 files (0 bytes) from volume Bay 3 HPFS+.
Copied 20 files (1.1 GB) from volume Bay 2 HPFS+.
Copied 1103 files (1.1 GB) from volume Macintosh HD.
Starting post-backup thinning
No post-back up thinning needed: no expired backups exist
Backup completed successfully.
(Finished May 4, 2010 2:38:17 PM)
I hope this is useful. Thanks for your help.
harv47

Safari fails to update followed links dynamically

I mentioned this a while ago and am surprised that Apple continues to produce perhaps the only browser which fails to update followed links dynamically.
The bug is best illustrated with an example. Hit this URL:
http://www.google.co.uk/search?num=100&newwindow=1&q=apple
and then try one or two links on the resulting Google page.
All other browsers I have tried update the followed links on the Google page dynamically without it being reloaded but Safari does not.
I do not use tabs and am not sure if those using tabs will be aware of the bug.
This is the only thing which stops me using Safari as my default browser.
I would be grateful if others can confirm that they also get this bug.

Many thanks bdash.
I am surprised it was not included with this week's Safari 3.2.1.
I have just tried iCab and the result is consistent with it being a WebKit issue.
The original bug report that you linked to compared Safari with Firefox but, from memory, with the exception of WebKit virtually all browsers produced from at least 5 series onwards have dynamically updated followed links.
I will put a link to this thread on
http://discussions.apple.com/thread.jspa?threadID=1702301
and any other pages about this issue which I come across.
Thanks again for your timely helpful reply - I will mark this as 'answered'.

AP1131G fail to bring ethernet link up

Similar Messages

Maybe you are looking for