AP1142 no longer joins controller (WLC55008)
This original post is edited to correct some factual errors, but the error remains and I still need help with my quaestion at the end!!
=======
Hello!
I have (and my customer) a rather "cute" problem ... Two months ago I installed a WLC5508 with sw r7.0.116.0 and we installed 8 AP1142 as a start. Everything came up and running and we were happy....
10 days the customer calls and says that the wlc logs error messages that says there is an IP-conflict with the management-interface. The conflict source is its own ip-adress!!! He reboots the WLC but the error message keeps coming. After a short while he notices that there are No APs on the WLC...!!!...
After some discussion I suggested that he should disconnect one of the two gig-ports of the WLC (LAG was enabled and in use). He did so and rebooted the WLC for good measure ... The IP-conflict disappeared but still no APs.....
In the DHCP-server (MS Win2003 server), in the AP-scope we also see that the "leased adresses" fills up with "BAD_IP_ADDRESS" (or the sort ... :-/ )
The setup is like this:
- WLC5508 running r7.0.116.0
- WLC has LAG activated and is connected to two different Cat3750G that are stacked
- The management if of the WLC is on the same subnet as the AP1142s, no other hosts on this subnet
- WLC management interface on own subnet as the only host (+ def gwy...)
- APs on their own subnet, no other hosts
- When the APs gets a IP-adress it is possible to ping them from the WLC!
- All VLANs/interfaces on the WLC is tagged, ie a "pure" trunk between WLC and 3750-stack
- Option 43 configured on the AP-scope
- All APs is connected via Power-injector (PWR-INJ4)
WLC5508 => LAG => 2x Cat3750G => TRUNK => Cat2960 with 1x AP1142 => TRUNK => Cat2960 with 6x AP1142
What we have done so far:
- Made sure the port-channel on the 3750-stack was configured: port-channel load-balance src-dest-ip
- Physically disonnected on port of the WLC
- Do "shutdown"on port gig-ports on the 3750-stack and "no shut" on only the one that is still physically connected to WLC
- Do "shutdown" on all AP-ports in the 2960-switches. Clear the lease-pool of the DHCP-server, Deactivate scope, Reactivate Scope and finally "no shut" on all AP-ports
Nothing helped, still no APs on the WLC.
I the connected my PC to the consloe of an AP that was easily accessible and powercycled it. The output can be seen below, the most peculiar was the line : " *Mar 1 00:15:53.351: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination"
Powering up and booting of AP1142:
=============================
using eeprom values
WRDTR,CLKTR: 0x88000800 0x40000000
RQDC ,RFDC : 0x80000037 0x00000211
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x88000800, 0x40000000
RQDC, RFDC : 0x80000037, 0x00000211
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is up.
PCIE1: VC0 is active
PCIEx: initialization done
flashfs[0]: 28 files, 8 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 7346176
flashfs[0]: Bytes available: 25038848
flashfs[0]: flashfs fsck took 20 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: e8:b7:48:25:b7:92
Ethernet speed is 1000 Mb - FULL duplex
Loading "flash:/c1140-k9w8-mx.124-23c.JA2/c1140-k9w8-mx.124-23c.JA2"...################################################################################################################################################################################################################################################################################################################################################################################################################################################################
File "flash:/c1140-k9w8-mx.124-23c.JA2/c1140-k9w8-mx.124-23c.JA2" uncompressed and installed, entry point: 0x4000
executing...
enet halted
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 13-Apr-11 12:50 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
flashfs[1]: 28 files, 8 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 32126976
flashfs[1]: Bytes used: 7346176
flashfs[1]: Bytes available: 24780800
flashfs[1]: flashfs fsck took 6 seconds.
flashfs[1]: Initialization complete.
flashfs[2]: 0 files, 1 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 11999232
flashfs[2]: Bytes used: 1024
flashfs[2]: Bytes available: 11998208
flashfs[2]: flashfs fsck took 0 seconds.
flashfs[2]: Initialization complete....done Initializing flashfs.
Ethernet speed is 1000 Mb - FULL duplex
Radio0 present 8363 8000 90020000 0 90030000 B
Radio1 present 8363 8000 98020000 0 98030000 0
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1142N-E-K9 (PowerPC405ex) processor (revision A0) with 98294K/32768K bytes of memory.
Processor board ID FCZ1519W2YU
PowerPC405ex CPU at 586Mhz, revision number 0x147E
Last reset from watchdog timer expired
LWAPP image version 7.0.116.0
1 Gigabit Ethernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: E8:B7:48:25:B7:92
Part Number : 73-12836-01
PCA Assembly Number : 800-33767-01
PCA Revision Number : A0
PCB Serial Number : FOC15161W2S
Top Assembly Part Number : 800-33775-01
Top Assembly Serial Number : FCZ1519W2YU
Top Revision Number : A0
Product/Model Number : AIR-LAP1142N-E-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:08.186: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:08.196: *** CRASH_LOG = YES
Security Core found.
Base Ethernet MAC address: E8:B7:48:25:B7:92
*Mar 1 00:00:09.753: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:10.322: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:10.351: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 8 messages)
*Mar 1 00:00:10.374: status of voice_diag_test from WLC is false
*Mar 1 00:00:11.417: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:12.513: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:12.549: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1140 Software (C1140-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 13-Apr-11 12:50 by prod_rel_team
*Mar 1 00:00:12.549: %SNMP-5-COLDSTART: SNMP agent on host APe8b7.4825.b792 is undergoing a cold start
*Mar 1 00:00:12.558: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Mar 1 00:13:24.043: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:13:24.113: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:13:24.121: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:13:24.129: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:13:24.145: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 1 00:13:25.113: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:13:25.121: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:13:25.635: %DOT11-2-TX_PWR_TIMO: Interface Dot11Radio1, Timed out waiting for fw to clear txp_pndg flag
*Mar 1 00:13:25.833: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:13:25.966: Interface Dot11Radio1 transmit power indices set/txp_pndg cleared
*Mar 1 00:13:25.989: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:13:26.843: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:13:32.229: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 172.22.130.126, mask 255.255.255.0, hostname APe8b7.4825.b792
*Mar 1 00:13:42.900: status of voice_diag_test from WLC is false
*Mar 1 00:13:42.957: Logging LWAPP message to 255.255.255.255.
User Access Verification
Username:
Translating "CISCO-CAPWAP-CONTROLLER.sodra.com"...domain server (172.21.51.23) [OK]
*Mar 1 00:13:52.990: %CAPWAP-5-DHCP_OPTION_43: Controller address 172.21.135.30 obtained through DHCP
% Username: timeout expired!
APe8b7.4825.b792 con0 is now available
Press RETURN to get started.
User Access Verification
Username:
*Mar 1 00:14:43.992: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:14:44.992: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
Username:
Username:
Not in Bound state.Username:
APe8b7.4825.b792 con0 is now available
Press RETURN to get started.
User Access Verification
Username: Cisc
*Mar 1 00:14:56.855: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.o
*Mar 1 00:14:56.875: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 172.22.130.126, mask 255.255.255.0, hostname APe8b7.4825.b792
Translating "CISCO-CAPWAP-CONTROLLER.sodra.com"...domain server (172.21.51.23) [OK]
*Mar 1 00:14:59.498: %CAPWAP-5-DHCP_OPTION_43: Controller address 172.21.135.30 obtained through DHCP
% Username: timeout expired!
APe8b7.4825.b792 con0 is now available
Press RETURN to get started.
User Access Verification
Username: Cisco
Password:
APe8b7.4825.b792>en
Password:
*Mar 1 00:15:40.498: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
Not in Bound state.
APe8b7.4825.b792#
APe8b7.4825.b792#
APe8b7.4825.b792#
APe8b7.4825.b792#
*Mar 1 00:15:53.351: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:15:53.376: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 172.22.130.126, mask 255.255.255.0, hostname APe8b7.4825.b792
Translating "CISCO-CAPWAP-CONTROLLER.sodra.com"...domain server (172.21.51.23) [OK]
*Mar 1 00:15:56.000: %CAPWAP-5-DHCP_OPTION_43: Controller address 172.21.135.30 obtained through DHCP
APe8b7.4825.b792#
APe8b7.4825.b792#
APe8b7.4825.b792#
===============================
My apologies for the rather massive amount of text.........
Questions:
1. It worked initially but after the ip-address confilct and reboot of WLC no APs associate to the WLC. Why??
2. The error message on the AP console: "*Mar 1 00:15:53.351: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination" What does this mean?
3. Since the AP gets an IP-address an it is possible to ping WLC -> AP, is there some freakish ogre in the Cat2960 that eats up the CAPWAP-packets??
Anybody who has a solution?????
Best Regards
Göran Blomqvist
TDC, Sweden
I have verified some facts and edited the original post, see the italics ....
- WLC on its own subnet
- APs on their own subnet
- DHCP-traffic works (to a point), AP gets ip-adress an is pingable from WLC but address-pool fills up with "BAD_ADDRESS"
- CAPWAP-traffic seems to "disappear" on the way from AP to WLC (in lack of a better phrasing)
Questions:
1. It worked initially but after the ip-address confilct and reboot of WLC no APs associate to the WLC. Why??
2. The error message on the AP console: "*Mar 1 00:15:53.351: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination" What does this mean?
3. Since the AP gets an IP-address an it is possible to ping WLC -> AP, is there some freakish ogre in the Cat2960 that eats up the CAPWAP-packets??
Anybody who has a solution?????
Best Regards
Göran Blomqvist
TDC, Sweden
Similar Messages
-
1242 is not joining controller
hello friends,
i have 1240 series access points which is not joining controller 5500 series..
here is logs at joining time below
AP503d.e56e.e7be#Xmodem file system is available.
flashfs[0]: 7 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 2649600
flashfs[0]: Bytes available: 13349376
flashfs[0]: flashfs fsck took 25 seconds.
Base ethernet MAC Address: 50:3d:e5:6e:e7:be
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
button is pressed, wait for button to be released...
button pressed for 37 seconds
process_config_recovery: set IP address and config to default 10.0.0.1
process_config_recovery: image recovery
image_recovery: Download default IOS tar image tftp://255.255.255.255/c1240-k9w7-tar.default
examining image...
%Error opening (connection timed out)Loading "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx"...#############################################################################################################################################
File "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:40 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
flashfs[1]: 6 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 2632192
flashfs[1]: Bytes available: 13366784
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1242AG-E-K9 (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FCZ150482DL
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 50:3D:E5:6E:E7:BE
Part Number : 73-10256-07
PCA Assembly Number : 800-26918-06
PCA Revision Number : A0
PCB Serial Number : FOC150158MH
Top Assembly Part Number : 800-29152-03
Top Assembly Serial Number : FCZ150482DL
Top Revision Number : A0
Product/Model Number : AIR-LAP1242AG-E-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:05.426: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 34 messages)
*Mar 1 00:00:07.500: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:07.526: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:40 by prod_rel_team
*Mar 1 00:00:07.601: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:08.500: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
*Mar 1 00:00:12.979: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
AP503d.e56e.e7be#
*Mar 1 00:00:46.445: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
AP503d.e56e.e7be#
AP503d.e56e.e7be#
AP503d.e56e.e7be#sh ver
Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:40 by prod_rel_team
ROM: Bootstrap program is C1240 boot loader
BOOTLDR: C1240 Boot Loader (C1240-BOOT-M) Version 12.4(13d)JA, RELEASE SOFTWARE (fc2)
AP503d.e56e.e7be uptime is 0 minutes
System returned to ROM by power-on
System image file is "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1242AG-E-K9 (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FCZ150482DL
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 50:3D:E5:6E:E7:BE
Part Number : 73-10256-07
PCA Assembly Number : 800-26918-06
PCA Revision Number : A0
PCB Serial Number : FOC150158MH
Top Assembly Part Number : 800-29152-03
Top Assembly Serial Number : FCZ150482DL
--More--
*Mar 1 00:00:56.445: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not haveTop Revision Number : A0
Product/Model Number : AIR-LAP1242AG-E-K9
Configuration register is 0xF
AP503d.e56e.e7be#
*Mar 1 00:01:06.445: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
any advice please??
thanksIt sounds like you are still working out IP connectivity, but I also noticed your AP is not for US regulatory domain.
Can you confirm that your WLC is ready to accept an AP with country code -E?
Your AP model: AIR-LAP1242AG-E-K9
From the WLC CLI
>show country
If you are in US, you should only have -A available. If this AP is intended to be used the US, then you will need to acquire an AP with the correct country code, as -E would not be supported in the US -A regulatory domain and should not be used. Perhaps this is for another location, so you may need to add the applicable regulatory domain support.
This link provides the list of the respective country codes and compatbility/etc.
http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps5861/product_data_sheet0900aecd80537b6a_ps6087_Products_Data_Sheet.html -
Cisco AP1142N won't join controller
Hi
When upgrading one of our WISM controller cards a problem occurred with some AP1142N.
The can’t join controller with 7.6.120.0, upgrading was from 7.4.121.0
When CLI into the AP I got this messages:
Reboot and tries to connect to the WISM2 with 7.6.120.0, but it fails.
Then tries to connect to another WISM2 with 7.4.121.0 and this work
But then the image on the AP is not correct (have a 7.6.120.0 image)
Downgrading AP to 7.4.121.0 image
Reboot and are back to number 1.
*Mar 1 00:01:09.564: %CAPWAP-3-ERRORLOG: Selected MWAR 'JKP-WISM-02-I '(index 0).
*Mar 1 00:01:09.564: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Sep 10 11:25:00.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.16.25 peer_port: 5246
*Sep 10 11:25:29.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
Translating "CISCO-CAPWAP-CONTROLLER.net.yyyy.se"...domain server (xxx.xxx.xxx.xxx) [OK]
*Mar 1 00:00:59.550: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:01:09.564: %CAPWAP-3-ERRORLOG: Selected MWAR 'JKP-WISM-02-I '(index 0).
*Mar 1 00:01:09.564: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Sep 10 11:25:00.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.16.25 peer_port: 5246
*Sep 10 11:25:29.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
*Sep 10 11:25:59.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.17.16.25:5246
*Sep 10 11:26:00.000: %CAPWAP-3-ERRORLOG: Selected MWAR 'JKP-WISM-02-I (index 0).
*Sep 10 11:26:00.000: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Sep 10 11:25:00.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.17.16.25 peer_port: 5246
*Sep 10 11:25:30.000: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
examining image...
extracting info (292 bytes)
Image info:
Version Suffix: k9w8-.124-23c.JA8
Image Name: c1140-k9w8-mx.124-23c.JA8
Version Directory: c1140-k9w8-mx.124-23c.JA8
Ios Image Size: 4915712
Total Image Size: 5110272
Image Feature: WIRELESS LAN|LWAPP
Image Family: C1140
Wireless Switch Management Version: 7.0.250.0
Extracting files...
c1140-k9w8-mx.124-23c.JA8/ (directory) 0 (bytes)
extracting c1140-k9w8-mx.124-23c.JA8/T5.bin (23836 bytes)
*Sep 10 11
extracting c1140-k9w8-mx.124-23c.JA8/8001.img (174932 bytes):25:59.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.17.16.25:5246With a WISM, you have by definition an etherchannel between your controller & APs. Try setting the load balancing algorithm on the switch housing the WISM to src-dst-mac before connecting the AP. There is/was an issue that shows itself rarely where other load balancing mechanisms interfere with an AP's initial join to a controller. The problem declined significantly over the years, but you may be running into it.
Once the AP joins, you can reset your load balancing and you shouldn't have the problem even if the AP reboots later. It usually impacts APs that have never joined your controller. Don't know why. Since this was an upgrade it may not be your problem, but it won't hurt to try. -
Flexconnect AP not joining Controller
Hi Community ,
I have some flexconnect APs in remote side . But they are not able to join controller 5508 (7.6) and flexconnect is also showing down in PI.
Any reason ??Hi Adam ,
Thanks for your reply .
Scenario is that we have 2 controllers in HQ . Controllers running IOS code 7.6 . APs are 1242 LAP . They were working fine just one week ago . But now I can see them they are not in the controller , though up . When I checked in PI , Flexconnect status showing down . Hope this will help . -
Airport Express no longer joins network
Greetings, I have a cable modem internet connection; I use an older Airport Extreme (802.11n, without Time Capsule) to make a local wifi network with WPA2 Personal security, and an older Airport Express (802.11 b/g, firmware 6.3) to connect a laser printer in a different room.
All was working well until two days ago when access to the internet disappeared. I reset the modem, confirmed that the cable connection was working by plugging a laptop directly into the modem by ethernet, determining that the problem was the Airport Extreme. I discovered the 7.5.2 firmware update which I uploaded, and all seemed well.
However, the 27" iMac upstairs only connected to Airport intermittently; it appeared to have been duplicated in name, as well as only recognized the Airport Express. I've since been able to correct that problem, however, now the Airport Express no longer connects to the Airport Extreme network.
I've tried soft resets (unplugging then plugging back in) and hard resets (pressing the reset button with a paperclip until the amber light flashes, then reconfiguring the device). I've tried setting the Airport Express both just to join the network (printer sharing) as well as extend the network; I also reverted the Airport Extreme's firmware to 7.4.2 which works perfectly well. However, now after each successive attempt to reconfigure the Airport Express to join the network, Airport Utility says that the Airport Express has been successfully updated and will restart, which it never does - it simply flashes an amber light, and Airport Utility eventually times out and says that it was unable to find the Airport Express after restarting, noting that the settings have been successfully updated, but that there is a problem re-joining the wireless network/finding the device. Notably, the Airport Express no longer appears in the left hand list of wireless devices in Airport Utility.
Help!!Hi pslebow,
You make it sound like there was no change, then suddenly the Airport Express 802.11g lost connection to the wireless network and you can't get it back.
What network security is your wireless network using?
From the specification sheet, "…When joining an existing wireless network, AirPort Express only supports WPA-Personal."
AirPort Express - Technical Specifications
Please make sure your router security is set to match.
iOS and OS X: Recommended settings for Wi-Fi routers and access points - Apple Support
If you have older Wi-Fi devices on your network that don't support WPA2 Personal (AES), a good second choice is WPA/WPA2 Mode (often referred to as WPA Mixed Mode). This mode will allow newer devices to use the stronger WPA2 AES encryption, while still allowing older devices to connect with older WPA TKIP-level encryption. If your Wi-Fi router doesn't support WPA/WPA2 Mode, WPA Personal (TKIP) mode is the next best choice.
Best,
Nubz -
Mac Book will no longer join wireless home network
I am having ongoing problems with getting my 2.0G black Mac Book to connect to my wireless home internet and network.
For the first six weeks I had my Mac Book it connected to the network without difficulty. I have a Belkin modem/router, a PC which connects wirelessly and also an airport express on my stereo for airtunes, which was also wirelessly connected. The network was WPA Personal encrypted.
The Mac Book will connect to other wireless networks without any difficulty.
About 3 days ago my Mac Book stopped connecting to my home network - the network name is visible in the airport list but when I tried to connect by entering the WPA password it rejected the password or it returned an "error joining the airport network". The PC and airtunes were still connecting without a problem. It was just the Mac Book that would not connect.
I adjusted the network settings to remove WPA security and the Mac Book then connected easily. However I was not happy about leaving my network unencrypted or unsecured, so I attempted to secure the network again using WPA. Once again,the PC or airtunes joining the network with WPA but the Mac Book would not accept the WPA Password.
I have read as many forum posts as I could find to get all the possible troubleshooting tips on this problem. Here's what I've tried:
1. Deleting the network from my preferred network list and deleting the password from my keychain, then adding it afresh after rebooting the router and the Mac Book
3. Renaming the ESSID to a shorter name
4. Downloading Airport Extreme Update 2007-002
5. Toggling airport on and off
6. Using the $ in front of the WPA Passkey (even though that is a fix for the WEP passwords only)
7. Removing the battery (yes, someone said it worked for them!)
I had no success in getting the Mac Book to connect to the WPA encrypted network (even though it was doing so easily last week!). I then resigned myself to removing the WPA security so that I could at least get an unsecured internet connection on the Mac Book (I was thinking I could deal with the security by hiding the ESSID and using MAC filtering - not ideal, but perhaps the next best solution).
Tonight I removed the WPA security and now the Mac Book will not even connect to the unsecured network. My network ESSID is visible in the airport menu but when I select it - I get the "error connecting to the Airport network' message. I have tried all the usual fixes again (deleting network and passwords and keychains, rebooting router and MacBook etc) but it will not connect to my network. It will, however, connect to my neighbour's unsecured network just fine.
As far as I can deduce, the problem is with how the Mac Book sees my wireless network. The PC is connecting to the network. The Mac Book is connecting to other networks. Have I muddied the waters in my Mac Book through the various fixes I have tried? If so, how can I fix it so that it connects to my unsecured network as easily as it connects to next door's?
Forget about trying to secure the network with WPA for now, I just want to get an unsecured connection at the very least.
Any help would be appreciated.Thanks for your suggestions.
I've looked into the problem a bit further and I think I can trace it to the OS X 10.4.9 updates and the 2007-002 Airport Update downloads. My difficulties accessing the WPA network began after I downloaded the most recent OS X updates. After I downloaded 2007-002 update (designed to make it EASIER to access third party wireless routers! Joke!) I wasn't even able to connect to the unsecured network.
It appears I am not alone with this problem - many others have complained of losing connectivity after downloading these updates. There is a relatively difficult and risky way to uninstall the updates but I have reservations about messing with the OS, and I fear the same problem will arise with future updates.
Because I am now so sick of mucking around trying to fix this and there doesn't seem to be a fix on the horizon, I have solved the problem by buying an airport express and ditching the belkin router. I have now re-established the network without any problems using the airport express. So much for Macs being simple and compatible - the reality is a long way behind the impressive tv advertising. -
i am trying to troubleshoot a 2125 WLC alongside a 1252 access point. The access point is not joining and the y both
have the same software image. See logs below:
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 5.2.193.0
RTOS Version..................................... 5.2.193.0
Bootloader Version............................... 4.0.191.0
Emergency Image Version.......................... 6.0.199.4
Build Type....................................... DATA + WPS
System Name...................................... Cisco_f4:f7:c0
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.828
IP Address....................................... 192.168.1.5
System Up Time................................... 6 days 2 hrs 42 mins 39 secs
System Timezone Location.........................
Current Boot License Level.......................
Next Boot License Level..........................
Configured Country............................... SI - Slovenia
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
--More-- or (q)uit
Internal Temperature............................. +49 C
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 3
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C8:4C:75:F4:F7:C0
(Cisco Controller) >show network summary
RF-Network Name............................. law school
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Mode..................... Disable
Ethernet Broadcast Mode..................... Disable
AP Multicast Mode........................... Multicast Address : 0.0.0.0
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Disable
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Enable
Mgmt Via Dynamic Interface.................. Enable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
Kindly advice what is missing?
many thanksConsole into the AP and post the output to the following commands:
1. sh version;
2. sh ip interface brief -
Cisco 2702 not joining controller
Controller code vs. 7.6.120.0
From the controller:
(Cisco Controller) >debug capwap packet enable
Warning! Enabling this debug with large number of AP's connected, May flood console with message logs !!!.
Are you sure you want to continue? (y/N)y
(Cisco Controller) >*spamApTask3: Mar 05 13:38:13.317: <<<< Start of CAPWAP Packet >>>>
*spamApTask3: Mar 05 13:38:13.317: CAPWAP Control mesg Recd from 192.168.1.28, Port 43295
*spamApTask3: Mar 05 13:38:13.317: HLEN 4, Radio ID 0, WBID 1
*spamApTask3: Mar 05 13:38:13.317: Msg Type : CAPWAP_DISCOVERY_REQUEST
*spamApTask3: Mar 05 13:38:13.317: Msg Length : 165
*spamApTask3: Mar 05 13:38:13.317: Msg SeqNum : 0
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_DISCOVERY_TYPE, Length 1
*spamApTask3: Mar 05 13:38:13.317: Discovery Type : CAPWAP_DISCOVERY_TYPE_UNKNOWN
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_WTP_BOARD_DATA, Length 62
*spamApTask3: Mar 05 13:38:13.317: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.317: WTP_SERIAL_NUMBER : AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_WTP_DESCRIPTOR, Length 40
*spamApTask3: Mar 05 13:38:13.317: Maximum Radios Supported : 0
*spamApTask3: Mar 05 13:38:13.317: Radios in Use : 0
*spamApTask3: Mar 05 13:38:13.317: Encryption Capabilities : 0x00 0x01
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_WTP_FRAME_TUNNEL, Length 1
*spamApTask3: Mar 05 13:38:13.317: WTP Frame Tunnel Mode : NATIVE_FRAME_TUNNEL_MODE
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_WTP_MAC_TYPE, Length 1
*spamApTask3: Mar 05 13:38:13.317: WTP Mac Type : SPLIT_MAC
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10
*spamApTask3: Mar 05 13:38:13.317: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.317:
IE : UNKNOWN IE 207
*spamApTask3: Mar 05 13:38:13.317: IE Length : 4
*spamApTask3: Mar 05 13:38:13.317: Decode routine not available, Printing Hex Dump
*spamApTask3: Mar 05 13:38:13.317: 00000000: 01 00 00 01 ....
*spamApTask3: Mar 05 13:38:13.317:
*spamApTask3: Mar 05 13:38:13.317: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 22
*spamApTask3: Mar 05 13:38:13.317: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.317:
IE : RAD_NAME_PAYLOAD
*spamApTask3: Mar 05 13:38:13.317: IE Length : 16
*spamApTask3: Mar 05 13:38:13.317: Rad Name :
*spamApTask3: Mar 05 13:38:13.317: AP1c6a.7aba.91ec
*spamApTask3: Mar 05 13:38:13.317: <<<< End of CAPWAP Packet >>>>
*spamApTask3: Mar 05 13:38:13.317: 1c:6a:7a:ba:91:e0 Discovery Request from 192.168.1.28:43295
*spamApTask3: Mar 05 13:38:13.317: 1c:6a:7a:ba:91:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 5, joined Aps =0
*spamApTask3: Mar 05 13:38:13.317: apModel: AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.317: apType = 41 apModel: AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.317: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28 port 43295
*spamApTask3: Mar 05 13:38:13.317: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28:43295
*spamApTask3: Mar 05 13:38:13.317: <<<< Start of CAPWAP Packet >>>>
*spamApTask3: Mar 05 13:38:13.318: CAPWAP Control mesg Recd from 192.168.1.28, Port 43295
*spamApTask3: Mar 05 13:38:13.318: HLEN 4, Radio ID 0, WBID 1
*spamApTask3: Mar 05 13:38:13.318: Msg Type : CAPWAP_DISCOVERY_REQUEST
*spamApTask3: Mar 05 13:38:13.318: Msg Length : 165
*spamApTask3: Mar 05 13:38:13.318: Msg SeqNum : 0
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_DISCOVERY_TYPE, Length 1
*spamApTask3: Mar 05 13:38:13.318: Discovery Type : CAPWAP_DISCOVERY_TYPE_STATIC_CONFIG
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_BOARD_DATA, Length 62
*spamApTask3: Mar 05 13:38:13.318: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.318: WTP_SERIAL_NUMBER : AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_DESCRIPTOR, Length 40
*spamApTask3: Mar 05 13:38:13.318: Maximum Radios Supported : 0
*spamApTask3: Mar 05 13:38:13.318: Radios in Use : 0
*spamApTask3: Mar 05 13:38:13.318: Encryption Capabilities : 0x00 0x01
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_FRAME_TUNNEL, Length 1
*spamApTask3: Mar 05 13:38:13.318: WTP Frame Tunnel Mode : NATIVE_FRAME_TUNNEL_MODE
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_MAC_TYPE, Length 1
*spamApTask3: Mar 05 13:38:13.318: WTP Mac Type : SPLIT_MAC
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10
*spamApTask3: Mar 05 13:38:13.318: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.318:
IE : UNKNOWN IE 207
*spamApTask3: Mar 05 13:38:13.318: IE Length : 4
*spamApTask3: Mar 05 13:38:13.318: Decode routine not available, Printing Hex Dump
*spamApTask3: Mar 05 13:38:13.318: 00000000: 01 00 00 01 ....
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 22
*spamApTask3: Mar 05 13:38:13.318: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.318:
IE : RAD_NAME_PAYLOAD
*spamApTask3: Mar 05 13:38:13.318: IE Length : 16
*spamApTask3: Mar 05 13:38:13.318: Rad Name :
*spamApTask3: Mar 05 13:38:13.318: AP1c6a.7aba.91ec
*spamApTask3: Mar 05 13:38:13.318: <<<< End of CAPWAP Packet >>>>
*spamApTask3: Mar 05 13:38:13.318: 1c:6a:7a:ba:91:e0 Discovery Request from 192.168.1.28:43295
*spamApTask3: Mar 05 13:38:13.318: 1c:6a:7a:ba:91:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 5, joined Aps =0
*spamApTask3: Mar 05 13:38:13.318: apModel: AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.318: apType = 41 apModel: AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.318: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28 port 43295
*spamApTask3: Mar 05 13:38:13.318: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28:43295
*spamApTask3: Mar 05 13:38:13.318: <<<< Start of CAPWAP Packet >>>>
*spamApTask3: Mar 05 13:38:13.318: CAPWAP Control mesg Recd from 192.168.1.28, Port 43295
*spamApTask3: Mar 05 13:38:13.318: HLEN 4, Radio ID 0, WBID 1
*spamApTask3: Mar 05 13:38:13.318: Msg Type : CAPWAP_DISCOVERY_REQUEST
*spamApTask3: Mar 05 13:38:13.318: Msg Length : 165
*spamApTask3: Mar 05 13:38:13.318: Msg SeqNum : 0
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_DISCOVERY_TYPE, Length 1
*spamApTask3: Mar 05 13:38:13.318: Discovery Type : CAPWAP_DISCOVERY_TYPE_UNKNOWN
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_BOARD_DATA, Length 62
*spamApTask3: Mar 05 13:38:13.318: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.318: WTP_SERIAL_NUMBER : AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_DESCRIPTOR, Length 40
*spamApTask3: Mar 05 13:38:13.318: Maximum Radios Supported : 0
*spamApTask3: Mar 05 13:38:13.318: Radios in Use : 0
*spamApTask3: Mar 05 13:38:13.318: Encryption Capabilities : 0x00 0x01
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_FRAME_TUNNEL, Length 1
*spamApTask3: Mar 05 13:38:13.318: WTP Frame Tunnel Mode : NATIVE_FRAME_TUNNEL_MODE
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_WTP_MAC_TYPE, Length 1
*spamApTask3: Mar 05 13:38:13.318: WTP Mac Type : SPLIT_MAC
*spamApTask3: Mar 05 13:38:13.318:
*spamApTask3: Mar 05 13:38:13.318: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10
*spamApTask3: Mar 05 13:38:13.318: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.318:
IE : UNKNOWN IE 207
*spamApTask3: Mar 05 13:38:13.318: IE Length : 4
*spamApTask3: Mar 05 13:38:13.319: Decode routine not available, Printing Hex Dump
*spamApTask3: Mar 05 13:38:13.319: 00000000: 01 00 00 01 ....
*spamApTask3: Mar 05 13:38:13.319:
*spamApTask3: Mar 05 13:38:13.319: Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 22
*spamApTask3: Mar 05 13:38:13.319: Vendor Identifier : 0x00409600
*spamApTask3: Mar 05 13:38:13.319:
IE : RAD_NAME_PAYLOAD
*spamApTask3: Mar 05 13:38:13.319: IE Length : 16
*spamApTask3: Mar 05 13:38:13.319: Rad Name :
*spamApTask3: Mar 05 13:38:13.319: AP1c6a.7aba.91ec
*spamApTask3: Mar 05 13:38:13.319: <<<< End of CAPWAP Packet >>>>
*spamApTask3: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:e0 Discovery Request from 192.168.1.28:43295
*spamApTask3: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 5, joined Aps =0
*spamApTask3: Mar 05 13:38:13.319: apModel: AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.319: apType = 41 apModel: AIR-CAP2702I-A-K9
*spamApTask3: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28 port 43295
*spamApTask3: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28:43295
*spamApTask0: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:ec Received LWAPP DISCOVERY REQUEST to 6c:fa:89:da:ff:00 on port '1'
*spamApTask0: Mar 05 13:38:13.319: Start of Packet
*spamApTask0: Mar 05 13:38:13.319: Ethernet Source MAC (LRAD): 1C:6A:7A:BA:91:ED
*spamApTask0: Mar 05 13:38:13.319: Msg Type :
*spamApTask0: Mar 05 13:38:13.319: DISCOVERY_REQUEST
*spamApTask0: Mar 05 13:38:13.319: Msg Length : 70
*spamApTask0: Mar 05 13:38:13.319: Msg SeqNum : 0
*spamApTask0: Mar 05 13:38:13.319:
IE : UNKNOWN IE 58
*spamApTask0: Mar 05 13:38:13.319: IE Length : 1
*spamApTask0: Mar 05 13:38:13.319: Decode routine not available, Printing Hex Dump
*spamApTask0: Mar 05 13:38:13.319: 00000000: 01 .
*spamApTask0: Mar 05 13:38:13.319:
IE : UNKNOWN IE 50
*spamApTask0: Mar 05 13:38:13.319: IE Length : 46
*spamApTask0: Mar 05 13:38:13.319: Decode routine not available, Printing Hex Dump
*spamApTask0: Mar 05 13:38:13.319: 00000000: 00 00 00 00 00 00 00 00 00 00 00 00 46 54 58 31 ............FTX1
00000010: 38 33 30 53 34 50 39 00 00 00 00 00 00 00 00 00 830S4P9.........
00000020: 00 00 00 00 01 01 00 0
*spamApTask0: Mar 05 13:38:13.319:
IE : RAD_PAYLOAD
*spamApTask0: Mar 05 13:38:13.319: IE Length : 14
*spamApTask0: Mar 05 13:38:13.319: H/W Version : 1
*spamApTask0: Mar 05 13:38:13.319: H/W Release : 0
*spamApTask0: Mar 05 13:38:13.319: H/W Maint : 0
*spamApTask0: Mar 05 13:38:13.319: H/W Build : 0
*spamApTask0: Mar 05 13:38:13.319: S/W Version : 7
*spamApTask0: Mar 05 13:38:13.319: S/W Release : 6
*spamApTask0: Mar 05 13:38:13.319: S/W Maint : 100
*spamApTask0: Mar 05 13:38:13.319: S/W Build : 0
*spamApTask0: Mar 05 13:38:13.319: Boot Version : 15
*spamApTask0: Mar 05 13:38:13.319: Boot Release : 2
*spamApTask0: Mar 05 13:38:13.319: Boot Maint : 4
*spamApTask0: Mar 05 13:38:13.319: Boot Build : 5
*spamApTask0: Mar 05 13:38:13.319: numSlots : 0
*spamApTask0: Mar 05 13:38:13.319: numFilledSlots : 0
*spamApTask0: Mar 05 13:38:13.319: End of Packet
*spamApTask0: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:ec Discarding discovery request in LWAPP from AP supporting CAPWAP
(Cisco Controller) >
From the AP:
*Mar 5 19:48:43.007: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Mar 5 19:48:43.007: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Mar 5 19:48:43.007: LWAPP_CLIENT_EVENT: spamSendDiscoveryRequest: sending discovery type 1 to 192.168.1.40
*Mar 5 19:48:53.007: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar 5 19:50:53.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.1 peer_port: 5246
*Mar 5 19:51:22.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
*Mar 5 19:51:52.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.1:5246
*Mar 5 19:51:52.999: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar 5 19:50:53.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.1 peer_port: 5246
*Mar 5 19:51:22.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
*Mar 5 19:51:52.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.1:5246
*Mar 5 19:51:52.999: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Mar 5 19:50:53.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.1 peer_port: 5246
*Mar 5 19:51:22.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
*Mar 5 19:51:52.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.1:5246
*Mar 5 19:51:52.999: %SYS-3-MGDTIMER: Uninitialized timer, timer stop, timer = 3AFD270. -Process= "CAPWAP CLIENT", ipl= 0, pid= 74
-Traceback= 119AF80z 12A89C8z 12AA11Cz 16F512Cz 17645ECz 16FF088z 172810Cz 17299B4z 1720150z 1720228z 17204ECz 1717E50z 172F6A0z 173075Cz 1324C90z 1309B58z
*Mar 5 19:51:52.999: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 5 19:51:52.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 5 19:51:52.999: %CAPWAP-3-ERRORLOG: Failed to load configuration from flash. Resetting to default config
*Mar 5 19:51:52.999: LWAPP_CLIENT_EVENT: parse_lwapp_config: hostname AP1c6a.7aba.91ec
end
*Mar 5 19:51:53.003: LWAPP_CLIENT_EVENT: lwapp_mesh_enable_dhcp - allow DHCP
*Mar 5 19:51:53.003: LWAPP_CLIENT_EVENT: parse_lwapp_config: cdp run
end
*Mar 5 19:51:53.003: LWAPP_CLIENT_EVENT: parse_lwapp_config: interface GigabitEthernet0
cdp enable
end
*Mar 5 19:51:53.003: LWAPP_CLIENT_EVENT: parse_lwapp_config: interface GigabitEthernet0.1
cdp enable
end
*Mar 5 19:51:53.003: LWAPP_CLIENT_EVENT: parse_lwapp_config: interface GigabitEthernet1
cdp enable
end
*Mar 5 19:51:53.007: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 5 19:51:53.007: LWAPP_CLIENT_EVENT: parse_lwapp_config: line vty 0 15
transport input all
exit
end"test mesh mode local" is not a supported command on the AP. I tried to see if there was another syntax but couldn't find it.
AP1c6a.7aba.91ec#test mesh mode local
^
% Invalid input detected at '^' marker.
AP1c6a.7aba.91ec#test ?
GigabitEthernet GigabitEthernet IEEE 802.3z
Virtual-Template Virtual Template interface
aaa AAA Authentication, Authorization and Accounting
arp_retry Test ARP Retry
capwap CAPWAP test commands
cef Cisco Express Forwarding test command
cpuaccounting CPU Accounting test commands
cpurmi CPU RMI test commands
crypto Test crypto functions
dpaa DPAA test commands
dtls DTLS test commands
ecc ECC test commands
evtlog Evtlog test commands
ifs IFS TEST code
interfaces Network interfaces
iphc IPHC testing
opssl OPSSL Test
pb Test parameter block file system
persistent Persistent commands
process Create/kill test processes
rib RIB function test
rmi RMI test commands
rtcp Test RTCP SSM
save save load monitor snapshot
spanning-tree Spanning Tree Subsystem
ssm SSM test commands
tar test tar file system
topology Routing Topology test command
transport TACTIC - transport test commands
AP1c6a.7aba.91ec#test
From the AP:
AP1c6a.7aba.91ec#show version
Cisco IOS Software, C2700 Software (AP3G2-RCVK9W8-M), Version 15.2(4)JB5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Thu 01-May-14 22:18 by prod_rel_team
ROM: Bootstrap program is C2700 boot loader
BOOTLDR: C2700 Boot Loader (AP3G2-BOOT-M) LoaderVersion 15.2(4)JB5m, RELEASE SOFTWARE (fc2)
AP1c6a.7aba.91ec uptime is 46 minutes
System returned to ROM by power-on
System image file is "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP2702I-A-K9 (PowerPC) processor (revision A0) with 204790K/57344K bytes of memory.
Processor board ID FTX1830S4P9
PowerPC CPU at 800MHz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.6.100.0
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 1C:6A:7A:BA:91:EC
Part Number : 73-15824-03
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC182876JM
Top Assembly Part Number : 800-41174-01
Top Assembly Serial Number : FTX1830S4P9
Top Revision Number : A0
Product/Model Number : AIR-CAP2702I-A-K9
Configuration register is 0xF
AP1c6a.7aba.91ec#
From the WLC:
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.6.130.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... xxxxxxx_lab
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 192.168.1.40
Last Reset....................................... Software reset
System Up Time................................... 0 days 1 hrs 0 mins 6 secs
System Timezone Location......................... (GMT -6:00) Central Time (US and Canada)
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
--More-- or (q)uit
Configured Country............................... US - United States
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +41 C
Fan Status....................................... 4700 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Burned-in MAC Address............................ 6C:FA:89:DA:FF:00
Maximum number of APs supported.................. 5
(Cisco Controller) > -
I upgraded a controller yesterday 5508 it went from a low code version 6.x to 6.0.196.0 then to 7.0.116.0. However although all the access points joined code 6.0.196.0 they refused to join 7.0.116.0. The aps are all 1242s.
The country codes etc were all fine so I do not understand what was going on.
Any ideas?
*spamApTask0: Jun 26 16:07:44.734: 00:3a:99:db:f3:20 Discovery Request from 10.0.0.183:55065
*spamApTask0: Jun 26 16:07:44.734: 00:3a:99:db:f3:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Discovery Response sent to 10.0.0.183:55065
*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Discovery Request from 10.0.0.183:55065
*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Discovery Response sent to 10.0.0.183:55065
*spamApTask7: Jun 26 16:07:45.308: 00:3a:99:db:fa:20 Discovery Request from 10.0.0.95:55080
*spamApTask7: Jun 26 16:07:45.308: 00:3a:99:db:fa:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask0: Jun 26 16:07:45.308: 00:3a:99:db:fa:20 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask0: Jun 26 16:07:45.308: 00:3a:99:db:fa:20 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask7: Jun 26 16:07:45.308: 00:3a:99:db:fa:20 Discovery Response sent to 10.0.0.95:55080
*spamApTask7: Jun 26 16:07:45.309: 00:3a:99:db:fa:20 Discovery Request from 10.0.0.95:55080
*spamApTask7: Jun 26 16:07:45.309: 00:3a:99:db:fa:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask7: Jun 26 16:07:45.309: 00:3a:99:db:fa:20 Discovery Response sent to 10.0.0.95:55080
*spamApTask7: Jun 26 16:07:45.511: 00:13:c3:e1:4c:e0 Discovery Request from 10.0.1.232:20023
*spamApTask7: Jun 26 16:07:45.511: 00:13:c3:e1:4c:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask7: Jun 26 16:07:45.511: 00:13:c3:e1:4c:e0 Discovery Response sent to 10.0.1.232:20023
*spamApTask0: Jun 26 16:07:45.511: 00:13:c3:e1:4c:e0 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask0: Jun 26 16:07:45.511: 00:13:c3:e1:4c:e0 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask7: Jun 26 16:07:45.512: 00:13:c3:e1:4c:e0 Discovery Request from 10.0.1.232:20023
*spamApTask7: Jun 26 16:07:45.512: 00:13:c3:e1:4c:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask7: Jun 26 16:07:45.512: 00:13:c3:e1:4c:e0 Discovery Response sent to 10.0.1.232:20023
*spamApTask4: Jun 26 16:07:46.516: 00:3a:99:db:fa:10 DTLS connection not found, creating new connection for 10:0:0:101 (55079) 10:0:1:45 (5246)
*spamApTask4: Jun 26 16:07:46.708: 00:3a:99:db:fa:10 DTLS connection closed event receivedserver (10:0:1:45/5246) client (10:0:0:101/55079)
*spamApTask4: Jun 26 16:07:46.708: 00:3a:99:db:fa:10 No entry exists for AP (10:0:0:101/55079)
*spamApTask4: Jun 26 16:07:46.708: 00:3a:99:db:fa:10 No entry exists in database
*spamApTask4: Jun 26 16:07:47.759: 00:3a:99:db:fa:a0 Discovery Request from 10.0.0.184:55084
*spamApTask4: Jun 26 16:07:47.759: 00:3a:99:db:fa:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask0: Jun 26 16:07:47.760: 00:3a:99:db:fa:a0 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask0: Jun 26 16:07:47.760: 00:3a:99:db:fa:a0 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask4: Jun 26 16:07:47.760: 00:3a:99:db:fa:a0 Discovery Response sent to 10.0.0.184:55084
*spamApTask4: Jun 26 16:07:47.760: 00:3a:99:db:fa:a0 Discovery Request from 10.0.0.184:55084
*spamApTask4: Jun 26 16:07:47.760: 00:3a:99:db:fa:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask4: Jun 26 16:07:47.760: 00:3a:99:db:fa:a0 Discovery Response sent to 10.0.0.184:55084
*spamApTask7: Jun 26 16:07:49.471: 00:13:c3:e1:4d:c0 Discovery Request from 10.0.1.239:20032
*spamApTask7: Jun 26 16:07:49.471: 00:13:c3:e1:4d:c0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask7: Jun 26 16:07:49.471: 00:13:c3:e1:4d:c0 Discovery Response sent to 10.0.1.239:20032
*spamApTask0: Jun 26 16:07:49.471: 00:13:c3:e1:4d:c0 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask0: Jun 26 16:07:49.471: 00:13:c3:e1:4d:c0 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask7: Jun 26 16:07:49.472: 00:13:c3:e1:4d:c0 Discovery Request from 10.0.1.239:20032
*spamApTask7: Jun 26 16:07:49.472: 00:13:c3:e1:4d:c0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask7: Jun 26 16:07:49.472: 00:13:c3:e1:4d:c0 Discovery Response sent to 10.0.1.239:20032
*spamApTask1: Jun 26 16:07:52.222: 00:13:c3:e1:4d:80 Discovery Request from 10.0.1.230:20027
*spamApTask1: Jun 26 16:07:52.222: 00:13:c3:e1:4d:80 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask1: Jun 26 16:07:52.223: 00:13:c3:e1:4d:80 Discovery Response sent to 10.0.1.230:20027
*spamApTask0: Jun 26 16:07:52.223: 00:13:c3:e1:4d:80 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask0: Jun 26 16:07:52.223: 00:13:c3:e1:4d:80 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask1: Jun 26 16:07:52.223: 00:13:c3:e1:4d:80 Discovery Request from 10.0.1.230:20027
*spamApTask1: Jun 26 16:07:52.223: 00:13:c3:e1:4d:80 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask1: Jun 26 16:07:52.224: 00:13:c3:e1:4d:80 Discovery Response sent to 10.0.1.230:20027
*spamApTask5: Jun 26 16:07:52.267: 00:3a:99:da:c7:70 DTLS connection not found, creating new connection for 10:0:0:181 (34152) 10:0:1:45 (5246)
*spamApTask1: Jun 26 16:07:52.274: 00:3a:99:db:ff:20 Discovery Request from 10.0.0.182:55099
*spamApTask1: Jun 26 16:07:52.274: 00:3a:99:db:ff:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask0: Jun 26 16:07:52.274: 00:3a:99:db:ff:20 Received LWAPP DISCOVERY REQUEST to e8:b7:48:9b:86:4f on port '13'
*spamApTask1: Jun 26 16:07:52.274: 00:3a:99:db:ff:20 Discovery Response sent to 10.0.0.182:55099
*spamApTask0: Jun 26 16:07:52.274: 00:3a:99:db:ff:20 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask1: Jun 26 16:07:52.275: 00:3a:99:db:ff:20 Discovery Request from 10.0.0.182:55099
*spamApTask1: Jun 26 16:07:52.275: 00:3a:99:db:ff:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0
*spamApTask1: Jun 26 16:07:52.275: 00:3a:99:db:ff:20 Discovery Response sent to 10.0.0.182:55099
*spamApTask1: Jun 26 16:07:52.306: 00:3a:99:db:f2:40 DTLS connection not found, creating new connection for 10:0:0:100 (55069) 10:0:1:45 (5246)
*spamApTask5: Jun 26 16:07:52.463: 00:3a:99:da:c7:70 DTLS connection closed event receivedserver (10:0:1:45/5246) client (10:0:0:181/34152)
*spamApTask5: Jun 26 16:07:52.463: 00:3a:99:da:c7:70 No entry exists for AP (10:0:0:181/34152)
*spamApTask5: Jun 26 16:07:52.463: 00:3a:99:da:c7:70 No entry exists in database
*spamApTask1: Jun 26 16:07:52.501: 00:3a:99:db:f2:40 DTLS connection closed event receivedserver (10:0:1:45/5246) client (10:0:0:100/55069)
*spamApTask1: Jun 26 16:07:52.502: 00:3a:99:db:f2:40 No entry exists for AP (10:0:0:100/55069)
*spamApTask1: Jun 26 16:07:52.502: 00:3a:99:db:f2:40 No entry exists in databaseSomething "weird" is on the newest 7.0.X. Here's my situation:
1. It doesn't happen to all new APs. When I mean "new", I mean out from a box including APs from RMA.
2. I've seen this in 1240, 1250, 1140. Haven't seen it on a 3500.
3. Here's how it goes ... When the AP, fresh from a box, connects to the networks, sees the WLC/WiSM and downloads the full IOS (OK so far). After the reboot the AP in question loads the new IOS and shows up in the WLC/WiSM. When I check CDP neighbors, NOTHING. What the ... ?
4. Go to the switch and do command "sh cdp neighbor" and what do I get? NOTHING.
5. Check PoE and show that it's IEEE.
For unknown reason, APs in this "trance" shuts off the CDP. I currently have a Cisco TAC Case trying to iron out this "feature". Doesn't appear on the 7.0.96.0 but happens to the newer one. -
1140 AP not joining controller
I have 3 AP's setup on my network and each port is configured the same exact way on the switches. One AP joined the controller fine but the other two are not joning it. They get the IP address but that is about it. When I go and check for the statistics on the WLC it tells me that they are not joined. Here is what the DEBUG shows:
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc CAPWAP Control Msg Received from 10.230.129.113:60844
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc packet received of length 97 from 10.230.129.113:60844
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc Msg Type = 1 Capwap state = 0
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc Discovery Request from 10.230.129.113:60844
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc msgEleLength = 1 msgEleType = 20
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc Total msgEleLen = 68
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc msgEleLength = 40 msgEleType = 39
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc Total msgEleLen = 24
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc msgEleLength = 1 msgEleType = 41
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc Total msgEleLen = 19
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc msgEleLength = 1 msgEleType = 44
*spamApTask5: Apr 18 18:13:01.198: c4:71:fe:8f:da:dc Total msgEleLen = 14
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc msgEleLength = 10 msgEleType = 37
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Vendor specific payload from AP C4:71:FE:8F:DA:DC validated
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Total msgEleLen = 0
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 12, joined Aps =1
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc 1. 1 0
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc 2. 232 3
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc 3. 1 0
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc 4. 12 0
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp: AC Descriptor message element len = 40
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc acName = WLCNAME
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp:AC Name message element length = 56
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp: WTP Radio Information msg length = 65
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp: CAPWAP Control IPV4 Address len = 85
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp: CAPWAP Control IPV6 Address len = 107
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp: Mwar type payload len = 118
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery resp: Time sync payload len = 133
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc Discovery Response sent to 10.230.129.113:60844
*spamApTask5: Apr 18 18:13:01.199: c4:71:fe:8f:da:dc WTP already released
Note: I have one "management interface" configured on 10.230.129.xxx network" Then I created two "AP Manager interfaces on the 10.230.129.xxx network and enabled dynamic AP Management on them".Ok, right, thats because whenever you type ANY number it TAGs the packets with that vlan id. 0 leaves the traffic untagged.
So even if it that IP belongs to vlan 10, if the port is as native (untagged) then on the WLC side should be 0
Thats how it was designed. -
VM with MS SQL will not longer join domain after a reboot
I setup several VM's and a domain. Everything was working fine until I had to shut down the machine. Now only 2 out of the 3 can join the domain. The third is a VM with MS SQL. It claims to be joined to the domain, but logging on using a domain account no
longer works and the VM cannot see DS. The IP address is still local.Hello,
When you said "The IP address is still local", did you means the IP address of the SQL Server VM is a static IP address of a virtual network? Or it use the dynamic IP address that assigned by default. If you had congifure a statice IP address, it will not
change after restart.
http://www.bhargavs.com/index.php/2014/03/13/how-to-assign-static-ip-to-azure-vm/
What error message did you received when logon with the domian account? please verify domain account is vaild and the password is not expired . What's more, you can also check the system event log, it should post more details about the issue.
Regards,
Fanny Liu
Fanny Liu
TechNet Community Support -
hi All,
I have a scenario where my 2602E is not joining a controller in US. AP is in Netherlands.
AP: AIR-CAP2602E-E-K9
Logs on WLC 5508:
*spamApTask4: Jan 29 10:26:37.398: 18:9c:5d:9b:4d:00 Bridge AP can not join MultiCountry Controller: Bridge mode AP 10.130.90.11:63313 cannot be supported on Multi Country Controll
*spamApTask4: Jan 29 10:26:37.406: 18:9c:5d:9b:4d:00 State machine handler: Failed to process msg type = 3 state = 0 from 10.130.90.11:63313
is there a way i can change the bridge mode from this AP to normal or Local so that it can be useD?
Any help will be great.
thanks
Roycecheck the following.
-
1130AG not joining controller - FAILED CRYPTO INIT
I am trying to join my 1130AG-E-K9 AP to my 2016 WLC, but it is stuck in a boot loop and will not connect to the controller. The error I'm getting is:
*Mar 1 00:00:29.584: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:00:29.585: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:29.598: %LWAPP-3-CLIENTERRORLOG: LWAPP Crypto Init (SSC): no certs in the SSC Private File
*Mar 1 00:00:29.598: %LWAPP-3-CLIENTERRORLOG: LWAPP Crypto Init: could not start PKI session
*Mar 1 00:00:29.598: %LWAPP-3-CLIENTERRORLOG: Failed to initialize Crypto. Rebooting
*Mar 1 00:00:29.663: %SYS-4-PUPDATECLOCK: Periodic Clock update with ROMMON failed, because size left in ROMMON (4294967295), size needed (29), error code (-1)
*Mar 1 00:00:29.663: %SYS-5-RELOAD: Reload requested by CAPWAP CLIENT. Reload Reason: FAILED CRYPTO INIT.
*Mar 1 00:00:29.664: %LWAPP-5-CHANGED: CAPWAP changed state to DOWNXmodem file system is available.
I found some details here: http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00808f8599.shtml, but I'm not sure what it means that I have a 'SSC AP'. I am not local to this AP, though I do have a console connection to it-what do I need to do to get it working again? It just continually goes through this error and reboots every 30 seconds or so, so it's useless at the moment.
Thanks!While that did help me potentially debug the AP, it seems the AP can not/is not reaching the WLC. Debugs on the WLC show other APs talking to it, but the only signature I'm picking up on the WLC from this AP is:
*Aug 08 20:34:36.376: 00:13:5f:fb:b4:f0 Echo Request from 10.50.0.25:44194
*Aug 08 20:34:36.376: 00:13:5f:fb:b4:f0 Echo Response sent to 10.50.0.25:44194
And from the AP itself:
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:06.475: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event (contains, 1024 messages)
*Mar 1 00:00:08.523: %LINK-3-UPDOWN: Interface FastEthernet0, changed state up
*Mar 1 00:00:08.548: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.4(21a)JA2, RASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:17 by prod_rel_team
*Mar 1 00:00:09.523: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthet0, changed state to down
*Mar 1 00:00:17.310: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthet0, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:20.591: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTRER
Writing out the event log to nvram...
*Mar 1 00:00:29.591: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTLER
*Mar 1 00:00:29.592: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:29.605: %LWAPP-3-CLIENTERRORLOG: LWAPP Crypto Init (SSC): no ce in the SSC Private File
*Mar 1 00:00:29.605: %LWAPP-3-CLIENTERRORLOG: LWAPP Crypto Init: could not st PKI session
*Mar 1 00:00:29.605: %LWAPP-3-CLIENTERRORLOG: Failed to initialize Crypto. Roting
*Mar 1 00:00:29.666: %SYS-4-PUPDATECLOCK: Periodic Clock update with ROMMON led, because size left in ROMMON (4294967295), size needed (29), error code (
*Mar 1 00:00:29.667: %SYS-5-RELOAD: Reload requested by CAPWAP CLIENT. Reloaeason: FAILED CRYPTO INIT.
*Mar 1 00:00:29.667: %LWAPP-5-CHANGED: CAPWAP changed state to DOWN
Is my only option at this point reverting back to a standalone image, then going back to a LW one?
Thanks again,
-Ryan -
1142 AP will not join Controller through a D-Link POE Switch
This is fun.
I'm trying to use 1142 APs with a 2504 Wireless Controller through a D-Link 48PT GBIT XSTACK SWITCH (DLI-DGS-3120-48PC/SI). (I know. Shame on me. Couldn't help it.)
At any rate, the 1142 AP joins with the wireless controller ONLY when I attach it directly to the controller. When connected directly to the controller the AP functions normally and all is well.
When I attach it through the D-Link switch, the AP flashs green several times, indicating that it can't find the controller.
I suspect that there's some setting on the D-Link switch that's preventing the AP from seeing the controller, but I have no idea what that might be.
Any suggestions would be helpful. Thanks.leolahoo,
Thanks for responding. I appreciate it very much.
I checked the management interface in the GUI on the controller (which is set to an internal IP address 10.1.1.20), but after doing that I am not sure what you mean by "the link should be untagged."
UPDATE: I just saw on the main interface screen that the VLAN identifier for the management interface is marked as "UNTAGGED."
Also note the ping test results I sent to Ron above.
Any idea as to where to proceed from here?
Thanks very much.
Ken -
Reset 1510 AP not joining controller
Hi
I have a 3750 Controller with 1510 access points. I have 1 access point that will not join. I think it was configured as a remote with a fixed IP address but I don't know what that address is, and I think that it is not the right subnet. I think I need to re-prime the AP with new settings.
Unfortunately I suspect that it because it has a set IP address it will now not try to get a DHCP address and thus I cannot prime it using that method. Is there another way to reset the IP address on these units?
Many Thanks
LPHi Laurie,
We do not run 1510's so I can't verify this, but I did come across this info;
Misconfigured Access Point IP address
IP address misconfiguration can occur when you are re-addressing a segment of your mesh network and you start at the mesh access point connected to the wired network (RAP). To avoid this problem, always start the IP addressing changes from the farthest access point and work your way back to the root access point. This problem might also happen if you move equipment such as uninstalling an mesh access point and then redeploying with a different IP subnet in another physical location on the mesh network.
Another option to fix this misconfigured IP address is to physically take a controller in Layer 2 mode with a root access point to the location of the misconfigured mesh access point. Set the bridge group name for the root access point to match the misconfigured access point. Add the access point's MAC address to the controller's filter list and enable Zero Touch Configuration. When the misconfigured access point appears in the controller's Summary page, configure the access point with an IP address.
From this doc;
http://www.cisco.com/en/US/products/ps6548/products_quick_start09186a00806b5d00.html#wp39368
Hope this helps!
Rob
Maybe you are looking for
-
Cannot save email attachments to folders in Finder
Ughhh, I'm getting a sinking feeling.... It's happening again. Ever since I installed Mavericks back in June of 2014, I've had nothing but problems. In fact, the actual install (perhaps coincidentally, I'm told) caused my hard drive to fail in mid-in
-
Boot Camp partition moved to external:"No bootable device found"
I have just installed a new SSD, moved my old OSX partition to the new drive and am currently using the old hdd in an enclosure as an external hard drive. I can access all my files on my old OSX partition and my bootcamp partition when connected to m
-
Pdf thumbnails in Windows 7 64bit?
How do I get my thumbnails to show up using Adobe Reader X and 64 bit Windows 7? Thanks
-
IPhoto 09 (v8.1.2) is released
Check software Update or http://support.apple.com/kb/DL970 This update addresses minor issues in the area of import and syncing to iPhone, iPod or Apple TV. As Always: *Back Up Before any Update* Regards TD
-
Hi Experts, Iam trying to develop an application by following the link How-to Build an Agentry based mobile app from scratch connecting to an SAP back-end Part1. I have created a class in java perspective,started the agentry connector stud