AP1200 options for "mixed" encryption methods

Using AP1200 access points, with PCM352 client cards....98% of my wireless devices are using the VPN client, tunneling to a VPN3030 concentrator.
A small amount dont have VPN capability. Can I configure the same access points to support both WEP based and non-WEP based clients ?
thnx
chuck

http://www.cisco.com/univercd/cc/td/doc/product/wireless/airo1200/accsspts/ap120scg/bkscgch4.htm doesn't indicate either way but I don't see anyway to provide wep support for one and not for all. Wouldn't it be better to require WEP for all your clients to cover the few that need it?

Similar Messages

  • HT1918 There's no none option for my payment method ?d

    How come there's no "none " option for my payment method?

    It may be that there is a balance on your account that needs to be taken care of before you can remove a credit card. If you are trying to create an account with a "none" option, see most of the threads to the right under "More Like This" including https://discussions.apple.com/thread/3929942

  • Airport Extreme Drop Outs -  Best Firmware/set-up  options for mixed Airport Devices

    I have an Airport Extreme (4th Gen) that I have connected to a Comcast modem.  I use this devise as a primary base station for my wireless network, and route an Ethernet cable from this Extreme to a D-Link 24 port switch.  The D-link is then connected to the various ports around my house via Cat5.
    Recently, I have been having trouble with my Internet connection dropping out periodically (not just wireless, but the Internet as well).  Had comcast out and all look good with the lines, signal, etc.  When I connect a computer directly to the Comcast modem (i.e. bypassing the Extreme), no drop outs.  So, I figured it was the Extreme (or potentially the D-Link, but feels more like the Extreme) so I bough a new Extreme (but have not installed yet).
    I have read in some of the forums that the firmware update on the Airport Extreme may be the culprit, but after downgrading, the issue still remains. I have a couple of Airpirt Expresses as well, of mixed Generations. 
    2 questions:
    1 - My buddy seemed to recall a site or page that showed the best Airport firmware options for a mixed generation Airport network.  I can't find it anywhere. Anyone know if this exists or where I might find something like this.
    2 - I am currently extending the network wirelessly, but also have that extender plugged in via Ethernet for faster speed when I want to connect via Ethernet.  Could this be causing issue.  I am now thinking I should have set the express up as a bridge (i.e. roaming network) rather than extender, and will do that when I install the new Extreme.  Could having the Express set up the way I currently do (wirelessly extending network AND connected via Ethernet) causing the issue (it has worked fine for the longest time, but maybe the new firmware doesn't like that).  I am not really that good with network stuff, so may be that's just a snipe hunt. 
    FWIW - I also just bought a brand new IMAC with Mavericks that is now on the network (via Ethernet). I mention this only because I feel like people have also mentioned connectivity issues with Mavericks.
    Any help would be appreicated. 

    First just install the new extreme to see if dropouts go away
    For the express, it should be setup to extend via wired (not wirelessly); power it off for now and just make sure the new extreme isn't suffering from dropouts
    Then factory reset the express so that it can be a wired extender, don't worry, it will also provide a wifi signal with the same credentials as your main extreme

  • Auto calculation row, work around for mixed calc methods?

    I have a problem with an auto calculation row. One of the columns in the report is a percentage so I want the total row to calculate using a column formula, instead of the Auto Calculation Row calculation method setting.
    We're using the auto calculation row as a way to churn through many Entity members, displaying financial totals for 4 Account category groupings for each Entity member.
    For each Entity, those 4 rows display the data they're supposed to, and the auto calc row generates the 'Total', which is the calculation method it is set to do.  With 2 columns in play, it works like this:
    A1 through A4 display data, and are summarised in [A][Total Row]
    B1 through B4 display data, and are summarized in [B][Total Row]
    An updated requirement for a % column came up, and now we're trying to get that to display properly in column [C]. 
    [C] is created as a formula column
    The formula is set to [B]/[A], and formatted to display 0.01 precision
    We expect each row to use this formula, and for rows 1 through 4 it does.
    However, for [Total Row], it does not calculate [B]/[A]... instead it calculates [C][1]+[C][2]+[C][3]+[C][4]
    This makes sense in terms of what the 'auto calculation row' is designed to do, or as to how it is explained in FR documentation.
    The calculation method is set to 'Total', so it just adds up all of the data.
    But we're looking for a combination of settings or a work-around that permits the Auto Calculation row feature to be used with mixed calculations as I've described.
    We're on FR 11.1.2.362
    Thanks
    Troy

    gofer wrote:
    Hi osgood, thanks for getting back, thanks for that suggestion, I think that's a nice way of going about it. The form is working great with the calculation but I still can't get it to work on the reply email back to the site.
    This is what I've used in the PHP form;
    $freight = $_POST['PROD_freight_1'];
    $totalcost = ($chardonnay_2011_bottles * 20 + $chardonnay_2011_cases * 204) + ($pino_gris_2011_bottles * 21 + $pino_gris_2011_cases * 228) + ($sauvigon_blanc_2011_bottles * 20 + $sauvigon_blanc_2011_cases * 204) + ($riesling_2012_bottles * 20 + $riesling_2012_cases * 204) + ($pinot_noir_2009_bottles * 25 + $pinot_noir_2009_cases * 250) + ($PROD_freight_1);
    This the code for the reply back to the site;
      \n selection \n $PROD_freight_1
    Cheers
    The variable should be:
    + ($freight);
    and
      \n selection \n $freight
    Does that work?

  • HT2534 There is no option for "none" payment method anymore?

    see the title, I need to download xcode but don't have a credit card, how do I do it?

    Peter, I had the same problems!  I could set up my account for iTunes without a card by doing the following:
    - open iTunes
    - Sign In
    - Get the message saying that the account must be reviewed for iTunes
    - click Review
    - Ok the Use Terms
    - on the screen where you see your username, password, security questions, there are two check boxes at the bottom for receiving emails from Apple (marketing stuff).  I was always deselecting these, but one time i just left them checked and clicked Continue
    - after leaving them checked, i then saw the NONE option next to PayPal.
    I did this with my existing account.  I tried creating a new account, but if I deselected those two options, i didn't see NONE even with the completely new account.
    Hope that helps you!  It was a bugger for me too!

  • Options for ReleaseSeqFileEx

    The documentation for the options to the Engine.ReleaseSeqFileEx function lists one option as:
    "ReleaseSeqFile_DiscardChanges - (Value: 0x1) Use this option to remove a modified sequence file from the Engine internal cache, thus discarding changes to the file..."
    My question is: if I use this option when releasing a sequence file, is an unmodified sequence file not removed from the internal Engine cache? If I don't use this option, does a modified sequence file remain in the cache? And is removing a file from the cache the same as releasing it? Basically, I want to release a sequence file, whether or not it has been modified, and be able to load a fresh sequence file in the future.
    Also, there are two options in the documentation for Re
    leaseSeqFile_UnloadFile and ReleaseSeqFile_UnloadFileIfModified, but they have no specified values. What do these options do and how are they used? What is the difference between unloading, releasing, and removing from the cache?
    Thanks.

    Hi Jeff,
    Yes, removing a file from the engine's internal cache is the same thing as releasing it. The main thing to keep in mind is that the file will remain in the cache until all references to it are released. There could be more than one reference to a file at any given time, whether your Operator Interface/Sequence Editor has a reference to it or an executing sequence has a reference to it, etc... Whenever you are editing a file in the Sequence Editor, the editor will maintain a list of changes you've made to the file until you save it. If you use the UnloadFileIfModified option when releasing, it will cause the editor to ignore the fact that it hasn't been saved (once a file has been saved, it is no longer in a "modified" state). You can combine the different options for the release method using the bitwise OR operator in the language you are calling it from since they are simply integer values. Try combining these options until you get the behavior that you would like. As you noted, there are some errors in the documentation for the options, in regards to what values they are, what they do specifically, and which ones are really valid/useful. Follow this guide for the options (notice that the DiscardChanges option is omitted; this option is not intended to be used externally by end-user programmers):
    ReleaseSeqFile_DoNotRunUnloadCallback�(Value: 0x2) Use this option to prevent the SequenceFileUnload callback from running if the callback exists and the reference being released is the last reference. If other references exist to the sequence file, TestStand may execute the SequenceFileUnload callback when these references are released using Engine.ReleaseSequenceFileEx.
    * Use the SequenceFile.UnloadCallbackEnabled property to prevent the SequenceFileUnload callback from ever being executed.
    ReleaseSeqFile_NoOptions�(Value: 0x0) No options.
    ReleaseSeqFile_UnloadFile�(Value: 0x4) Use this option to request TestStand to remove a sequence file from the engine's internal cache. When you specify this option, it does not guarantee that TestStand will remove the sequence file from the cache because there may be multiple references to it or it may be executing. If you do not specify this option, TestStand may remove the sequence file from the cache if TestStand no longer needs the file.
    ReleaseSeqFile_UnloadFileIfModified�(Value: 0x1) Use this option to remove a modified sequence file from the engine's internal cache.
    Jason F.
    Applications Engineer
    National Instruments
    www.ni.com/ask

  • Select-options for OO Methods

    Hi all,
    How can I define select-options for a method in a global class.
    And how can I pass these select-options from a report.
    Thanks & Regards
    Eshwar

    Hi all,
    How can I define select-options for a method in a global class.
    And how can I pass these select-options from a report.
    Thanks & Regards
    Eshwar

  • I am from India using my iphone4 with Vodafone and  firmware version 5.0.1(9A405). I am unable to access 3G from my device as the CELLULAR DATA NETWORK option in the settings is missing. Any methods or options for fixing the same????

    I am from India using my iphone4 with Vodafone and  firmware version 5.0.1(9A405). I am unable to access 3G from my device as the CELLULAR DATA NETWORK option in the settings is missing. Any methods or options for fixing the same????

    I am from India using my iphone4 with Vodafone and  firmware version 5.0.1(9A405). I am unable to access 3G from my device as the CELLULAR DATA NETWORK option in the settings is missing. Any methods or options for fixing the same????

  • Log onto incoming mail server (POP3): Your server does not support the connection encryption type you have specified. Try changing the encryption method. Contact your mail server administrator or Internet service provider (ISP) for additional assistance.

    Hi All,
    This is my first post to ms exchange forum am getting  Log onto incoming mail server (POP3): Your server does not support the connection encryption type you have specified. Try changing the encryption method. Contact your mail server administrator
    or Internet service provider (ISP) for additional assistance. in my outlook clients, till last Sunday (12.04.15) my exchange was well & good, Monday morning suddenly the problem started like none of our outlook pop3 clients are able to communicate
    with exchange (rest  IMAP, SMTP & Exchange accounts are working fine). i have tried with all port no but no luck. please help me to get raid of this one.
    Exchange 2013 CU6 with server 2012 Std 64Bit
    Thanks,
    Murali 

    Dear All,
    I have found the solution for above problem, the problem has occur due to PopProxy inactivity
    please find relevant exchange management shell commends below.
    1. Get-ServerComponentstate -Identity <yourmailserver.com> 
    Server Component State
    yourmailserver.com ServerWideOffline Active
    yourmailserver.com HubTransport Active
    yourmailserver.com FrontendTransport Active
    yourmailserver.com Monitoring Active
    yourmailserver.com RecoveryActionsEnabled Active
    yourmailserver.com AutoDiscoverProxy Active
    yourmailserver.com ActiveSyncProxy Active
    yourmailserver.com EcpProxy Active
    yourmailserver.com EwsProxy Active
    yourmailserver.com ImapProxy Active
    yourmailserver.com OabProxy Active
    yourmailserver.com OwaProxy Active
    yourmailserver.com PopProxy Inactive
    yourmailserver.com PushNotificationsProxy Active
    yourmailserver.com RpsProxy Active
    yourmailserver.com RwsProxy Active
    yourmailserver.com RpcProxy Active
    yourmailserver.com UMCallRouter Active
    yourmailserver.com XropProxy Active
    yourmailserver.com HttpProxyAvailabilityGroup Active
    yourmailserver.com ForwardSyncDaemon Active
    yourmailserver.com ProvisioningRps Active
    yourmailserver.com MapiProxy Active
    yourmailserver.com EdgeTransport Active
    yourmailserver.com HighAvailability Active
    yourmailserver.com SharedCache Active
    2. Set-ServerComponentState -Identity <yourmailserver.com> -Component PopProxy -Requester HealthAPI
    -State Active
    3. Get-ServerComponentstate -Identity <yourmailserver.com> 
    Server Component State
    yourmailserver.com ServerWideOffline Active
    yourmailserver.com HubTransport Active
    yourmailserver.com FrontendTransport Active
    yourmailserver.com Monitoring Active
    yourmailserver.com RecoveryActionsEnabled Active
    yourmailserver.com AutoDiscoverProxy Active
    yourmailserver.com ActiveSyncProxy Active
    yourmailserver.com EcpProxy Active
    yourmailserver.com EwsProxy Active
    yourmailserver.com ImapProxy Active
    yourmailserver.com OabProxy Active
    yourmailserver.com OwaProxy Active
    yourmailserver.com PopProxy Active
    yourmailserver.com PushNotificationsProxy Active
    yourmailserver.com RpsProxy Active
    yourmailserver.com RwsProxy Active
    yourmailserver.com RpcProxy Active
    yourmailserver.com UMCallRouter Active
    yourmailserver.com XropProxy Active
    yourmailserver.com HttpProxyAvailabilityGroup Active
    yourmailserver.com ForwardSyncDaemon Active
    yourmailserver.com ProvisioningRps Active
    yourmailserver.com MapiProxy Active
    yourmailserver.com EdgeTransport Active
    yourmailserver.com HighAvailability Active
    yourmailserver.com SharedCache Activ
    Replace yourmailserver.com with your server host name.
    Thanks

  • Options for image format and encryption when creating disk image?

    I am trying to help someone via email, so I am not positive that he is doing everything I tell him .
    He was having problems with creating a disk image of his project, but I thought he was getting it now until he sent me a message asking what settings I select when creating a disk image. He included a picture that has the options in drop-down bars. The first two are not a problem, but I don't know where the second two are coming from, as I have never gotten those:
    +Save As: [Name of project]+
    +Where: [Location]+
    These two are what I see each time I do a 'Save as disk image' but he also has a block with these other two options, that I have never seen. I put his default selections in the brackets:
    +Image Format [read-only]+
    +Encryption: [none]+
    I took a look at iDVD's options for archiving a project, thinking that he had done that, but I still do not get these options.
    Any information appreciated.

    Beverly Maneatis wrote:
    ... How do I get a screenshot into these replies?
    send me an email, Bev, I'm shy to publish here that simple html code.. (picture has to be on some webspace...) .. I want to avoid, some 'beginner' posting here 10Mpixel vacation pics....

  • What is the encryption method for the user's password?

    hi all,
    who knows what is the encryption method for the user's password?
    the password is 803004, and i get the encrypted string "D7EDED84BC624A917F5B462A4DCA05CDCE256EEEEEDC97D59A57930E06CF9781E022CC8E430FF04E"
    thanks,
    dan

    There is no default password for a guest user unless you've created one:
    (screenshot from the System Pref Guest User Pane)

  • Available HTTP delivery options for Flash Access encrypted content

    Dear colleagues,
    Could you please clarify available HTTP delivery options for Flash Access encrypted content.
    Standard HTTP DS scheme with Apache web server getting chunks of video from segmented with f4fpackager file.
    HTTP Progressive Download of encrypted with Flash Access file (non segmented).
    Is it possible to use byte range delivery in this case in order to start playback from custom position (seek)?
    Are there any pitfalls in this case? Is it required to make encryption blocks aligned with keyframe intervals or something like that?

    Thanks for your response, seems though that only the encrypted videos appear to have a problem because when I tried some un-encrypted videos (again from adobe http://drmtest.adobe.com/content/unencrypted/Indesign.f4v ) it played fine.
    Maybe is has something to do with the decryption process and the hardware of the mobile phone after all.
    Again thanks for your response.

  • Best option for Asynchronous method invocation? JMS or Pure Java Thread

    Hi,
    We've a swing based Client application which is supposed to run with a server in J2EE environment. Some process like Search etc are very time consuming. So we are going for asynchronous process.
    Now the question is to find a best option for this. Two possible candidates are
    1. JMS
    2. Java Thread.
    Can anybody suggest me which one is the best option in this context?

    Actually my thought was the issues with code maintainability.Maintainability is different issue, it is much related to OOAD and design pattern you might want to choose to avoid coupling (thus high reusability and maintainability - eg: for future enhancement, etc)..
    public interface SearchService {
         public static class DefaultFactory {
                 public SearchService getInstance() {
                          return HttpSearchService.getInstance();
         public void search (String[] keywords, Observer obs);
    public class HttpSearchService implements SearchService {
         public static HttpSearchService getInstance() {
                ... bla bla bla singleton ...
         public void search(final String [] keywords, final Observer obs) {
                     (new Thread() {
                              public void run() {
                                    .. do http request ...
                                    List result =  ... parse http response ...
                                    obs.update(list);
                     }).start();
    SearchService ss = SearchService.DefaultFactory.getInstance();
    ss.search( new String[] { "get", "me", "my" , "dukes" }, myTableModel );
    ...You can, in future, replace the default factory HttpSearchService with something faster, more appropriate SearchService, without changing many codes.
    rgds,
    Alex

  • Need suggestion for data encryption

    Hello Experts,
    I need your expert opinion on one of the data encryption method. We have some legal compliance to implement data encryption as listed below, lets say we have to apply encryption on 2 tables (1) TAB_A (2) TAB_B.
    (1) Need data encryption on the TAB_A & TAB_B for 2-3 columns and not the entire table.
    (2) Data should not be in readable format, if anyone connect to database and query the table.
    (3) We have reporting services on our tables but reporting services doesn't connect to our schema directly rather they connect to a different schema to which we have given the table Select grant.
    (4) Reports should work as it is, and users should see the data in readable format only.
    (5) There are batch processes which generates the data into these tables and we are not allowed to make any changes to these batch processes.
    This is a business need which has to be delivered. I explored various options such as VPDs, Data encryption methods etc but honestly none of these are serving our business need. There is also a limitation of encrypting data as data volume of quiet high (30TB DB) and generally users query the data on millions of records at a time. Also reports have very tight SLAs as well. If we create any encryption wrapper then decrypt will take longer in reports and will cause the SLA miss for reports.
    Could someone please suggest any better solution to me or if something is inbuilt in Oracle? We are using Oracle 11g.
    Regds,
    Amit.

    you can read about Transparent Data Encryption
    Check
    http://docs.oracle.com/cd/B28359_01/network.111/b28530/asotrans.htm

  • BODS : Datastore options for SAP R/3 - need clarity for use

    Hi All.
    Another request to understand the datastore optiono n BOXI 3.1 BODS existing installation.
    We are trying to pull a new table from SAP R/3 into BODS and we find that ABAP program is not getting generated as expected. And terminates. When we tested a simple workflow.
    While creating a new datastore for SAP R/3 Source :
    When we look at the datastore we find the following options for R3 Source ;
    ABAP Execution option :
    Execute preloaded
    Generate and execute
    Under data transfer method we find ;
    Shared directory
    Direct download
    FTP
    Custom transfer
    Then we have working directory on sap server
    local directory
    generated ABAP Directory
    Am testing a simple workflow of pulling data from SAP R/3 in a dev machine.
    But am not understanding.
    which option of ABAP Execution, and data transfer , path would work in co-ordination.
    Because when i say direct download and say generate and execute it throws error.
    Can anyone help me with combinations of the options to choose for a R/3 source. And the implications thereof.
    I had created a folder under local bods server D:\Bodi. And given the path for data transfer.
    But the files are not getting generated for whatsoever reasons.
    Any advise on this would be helpful.
    Also found a bit unusual, that there was no button to test the connection to be correct or not, a TEST connection button is not there. Which i felt, could be included.
    Note : on the existing production system, we have chosen execute preloaded; shared directory on sap server. and shared that folder path for the user and given full rights. But while we try to do the same on the dev machine a test before transporting on production, a simple workflow does not work.
    would like to know what settings on sap server, really affect the data store options on the BODS
    thanks
    indu
    Edited by: Indumathy Narayanan on Jul 19, 2011 4:14 PM

    Indeed, BODS <> SAP connectivity can be tricky.
    For a development environment, I suggest you select the option "Generate and execute" for your "ABAP Execution Option." What this means is that DS will create, on the fly, small-ish ABAP programs. These ABAP programs will be written, in plain text, to a local directory on the DS job server, in the folder specified in "Generated ABAP Directory".  You can see them in there after an attempted job execution, assuming the job involves the creation of an ABAP program.  The ABAP program name is specified in the properties of an ABAP data flow, under Options > ABAP Program Name.  If you can't, perhaps the DS job server process doesn't have full rights to that folder - ?  After being generated on-the-fly, they'll be transferred to SAP to execute.  The SAP user you use to connect to SAP must have sufficient rights to upload-and-execute these ABAP programs, and that's a fairly substantial set of rights. What's required is documented in the BODS supplement for SAP. Often, to get things running, your friendly local Basis admin will grant SAP_ALL to the DS user, to see what rights are being invoked.
    Once all that jazz is working, you need to get the data back. There are a number of ways to do this. The method of data transfer is specified in "Data transfer method," where, ignoring "Custom transfer," you have three choices:
    1) Direct Download: easiest and slowest.  This method tells SAP to attempt to stick data in the client-side folder specified in "Local directory." Try this first.
    2) Shared folder: This is recommended when you have SAP being hosted on a Windows box. Basically: you set "Working directory on SAP Server" and "Data Services path to the shared directory" to point to the same folder.  SAP uses the "Working directory on SAP Server" to find this folder, and DS uses the other setting. So, for instance, if you were going to use the Shared folder method, you could set "Working directory on SAP Server" to "E:\BODS_Transfer", and, assuming E:\BODS_Transfer was shared-out as "BODS_Transfer", you could set "Data Services path to the shared directory" to
    dev12.somecompany.com\BODS_Transfer .  Then, you'd need to setup all the relevant security, as both SAP and DS need rights to read and write files in this folder.
    3) FTP (this is the method I usually use): SAP writes the "transport files" you're after (i.e., the data) in the folder specified in "Working directory on SAP Server". Then, you need to establish ftp connectivity to that folder from the DS job server's perspective, which you do by entering the ftp host name and the path to that folder in "FTP host name" and "FTP relative path to the SAP working directory".  In my opinion, the "relative" business is a little confusing, and I just typically enter the full ftp path, beginning the path w/ a forward slash, like "/usr/sap/tmp/BOBJ" or something like that.  You also need to obtain a separate username and password for the ftp connectivity. Note that this name and password has NOTHING to do with the SAP username and password; you're just setting-up DS to act as an ftp client. I strongly encourage you to test ftp connectivity by using a regular ftp client from the DS job server and attempt to connect to your ftp host using the username and password you were given, and attempting to fetch some sample test file. If you can't do this, manually, then DS won't be able to do it, either.
    Best wishes,
    Jeff Prenevost

Maybe you are looking for